COMPREHENSIVE DAILY MAINTENANCE SERVICES, CERTAIN B/R REPAIRS TO JOINERY, FLOORING, PLASTERING AND PLUMBING ETC TO BLDGS IN ZONE B AT DAMANA UNDER GE JAMMU

Amount

Taking down chowkats or frames with shutters (w/o taking off shutters from the frames) not exc 1.5 sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt), and removing from site all as specified and as directed by Engr-in-Charge.

Description same as per Ser item No 1.00 here-in-before but exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete and removing from site all as specified and directed by Engr-in-Charge.

Taking down shutters and refixing in same opening after resecuring or easing and adjusting, also refixing builders hardware as required including renewal of unserviceable screws etc of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed by Engr-in-Charge.

M&L Factory made pressed steel frames of size 105x60mm made out of PBI sheet 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete including bottom of each chowkat to be welded with 02 no's 25x25x3mm angle iron projecting 10cm one either side including one shop coat of red oxide chrome primer and including PCC 1:3:6 type C-O in back filling of chowkats and tarring back of chowkats and holdfasts complete all as specified and as directed.

Description same as per Ser item No 5.00 here-in-before but frame size125x60mm complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet and edges will be painted to match with printed sheet, reinforced with MS square tube supplying and fixing in opening as per specification complete all as specified and as directed.

S&F 30 mm thick PVC wood grain printed factory made panel door shutter (style) consisting of frame made out of MS tubes for top and bottom rail, MS Frame shall be covered with heat moulded wood grain printed PVC channel and 5 mm thick X 15 mm wide PVC Sheet beading used inside style and rails and decorative PVC beading of 10x10 mm used instead of exposed portion of PVC sheeet beading as in toilet / kitchen cabinet shutters complete all as specified and as directed.

S&F mild steel butt hinges medium weight 75 mm long complete all as specified and as directed.

S&F 30mm thick Flush shutters, soild core construction, with particle board core and plywood face panels, both faces are covered with decorative face veener with lipping/frame to match complete all as specified and directed by Engr-in-Charge.

S&F 35mm thick Factory made Ist class hard wood, glazed and skelton shutter open rebated and prepared to receive glass, guage, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. sizes of members of shutters as specified in SSR 2009 Pt-I Section 8.24(b) supplied and fitted to chowkhats complete all as specified and as directed.

S&F mild steel butt hinges medium weight 100 mm long complete all as specified and as directed.

S&F box type steel windows / Ventilator (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler / AC window complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3. Note:- The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 no's MS steel lugs made of 20X5 mm iron flat 200 mm long. (iii)10 mm Sq Bar grill / guard bar design as per drawing. (iv) PCC block for embedding lugs

S&F framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks, cupboard frames etc (including cutting holes in brick masonry walls and fixed with PCC 1:1 1/2:3) and similar work confirming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F in repairs 18/19 mm thick Prelaminated Particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws / nails to timber / steel frame work as in shelves, cup board shutters, book case, writing table stand, shelves etc including fixing of plain fillets square or rectangular of 2nd class hard wood not exc 3 sq.cm in leaping to shutters / shelves complete fixed all as specified and as directed.

S&F continuous piano hanges, mild steel, bright finish or electrogalvanised, width of flap 30mm (when open) fixed with welding complete all as specified and as directed.

S&F Hasp and staple size 100 mm, alumium anodised, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F Aluminium handle cast type, anodised size 150mm long, 'D' type complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolts, with bright bolt and fixed 200mm complete all as specified and as directed.

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F in repairs Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F in repairs Helical door spring 150mm including roller and roller plate complete fixed with welding to existing steel chowkhats all as specified and directed.

Hacking out old broken glass of any thickness, size, quality or description from the wooden / steel frames glazing with putty or fixed with wooden beads complete all as specified and as directed.

S&F 3mm thick ordinary glass sheet quality and glazing with oil putty in square n. exc 0.5 sqm in each pane including punching or drilling out old glazing pins or spring clips and providing and fixing new clips or pins, including scaffolding to reach up to 4 story building all as specified and as directed.

Description same as per Ser item No 25.00 here-in-before but frosted glass complete all as specified and as directed.

M&L applying two coats of synthetic enamel paint on wooden surface over one coat of pink primer including preparation of new surface over 10 cm width or girth complete all as specified and as directed.

M&L for two coats of synthetic enamel paint on old steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of new surface all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing and making good, cutting not exc. 10cm girth complete all as specified and as directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 15mm all as specified and as directed.

Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 20mm all as specified and as directed.

S&F steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm all as specified and as directed.

S&F steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20mm all as specified and as directed.

Refixing only 15mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and as directed.

Refixing only 20mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and as directed.

M&L for Opening of air lock / blockage in GI pipe line from outlet of water tank to all internal GI pipes / fittings to smooth flow of water from bib taps / shower / WHB pillar tap / stop valves complete by air pressure / water gravity pressure etc complete all as specified and as directed.

M&L for replacing 15 mm GI fittings of medium grade ISI marked like butt Elbow, socket, nipple, union socket, tee etc complete all as specified and as directed at site.

M&L for replacing 20 mm GI fittings of medium grade ISI marked like butt Elbow, socket, nipple, union socket, tee etc complete all as specified and as directed at site.

Complete removal of vegetations, roots and shrubs from wall and making good the wall with cement, brick work and plastering including all scaffolding up to 4 storey building complete all as specified and as directed.

M&L for repairs to steel windows / doors by using welding machine where necessary thicknesss of each welding spot exceeding 6mm but not exceeding 9mm complete all as specified and as directed at site.

Easing of existing doors / windows of any description complete all as specified and as directed at site.

M&L for disconnecting existing tanks of capacity exc 250 ltrs but n exc 500 ltrs, setting aside for repairs, cleaning etc and hoisting if required reconnecting and refixing in position after cleaning and removing all scale dirt etc from tanks complete all as specified and as directed at site and writing date of cleaning with synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for disconnecting existing tanks of capacity exc 500 ltrs but n exc 1000 ltrs, setting aside for repairs, cleaning etc and hoisting if required reconnecting and refixing in position after cleaning and removing all scale dirt etc from tanks complete all as specified and directed at site and writing date of cleaning with synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC low level flushing cistern valve less, syphonic action type of 10 ltrs capacity white with inlet, ball valve, float and handle including cast iron brackets, PVC flush pipe 32mm dia, PVC connection (15 x 450 mm) long complete all as specified and as directed.

Material and Labour repairing of PVC low level / high level cistern by changing its internal fitting including PVC flush pipe etc complete all as specified and as directed at site.

S&F in repair Vitreous china squatting pan 'Orissa' pattern size 580 x 440mm white, with integral foot rest 'P' or 'S' trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe, etc. complete making good to floor as existing complete all as specified and directed by Engr-in-Charge.

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, flush pipe and joints complete all as specified and directed by Engr-in-Charge.

S&F in repairs stainless steel sink with drainage board, made of 1.00mm thick sheet for kitchen or laboratory with plug, washers, waste pipe including bedding in cement mortar to dwarf wall or including fixing cast iron cantilever brackets, connecting union to pipe, overall size 915mmx460mm, bowl size (410x330x160mm) as in repair complete all as specified and as directed.

S&F in repairs kitchen plate rack of stainless steel of size 900 x 800 x 230mm made out of 1mm thick stainless steel sheet all as specified and as directed.

S&F in repairs Vitreous china wash hand basin white, flat back of size 550x400mm including cutting for and pinning in ends of brackets or erecting stand complete all as specified and as directed by Engr-in-Charge.

S&F in repairs Pillar tap fancy type chromium plated with capstan head, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipes 15 mm bore dia complete all as specified and as directed.

S&F in repairs brass CP Mixer of bore dia of pipe 15mm for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed. Make: - Jaquar, Cera, Kohler

Dismantling PVC water tank / demolition of RCC water storage tanks of capacity upto 1000 ltrs and removing from site complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tank including plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 500 ltrs including making connections, 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (min wt 210 gram) complete all as specified in SSR Part-I.

S&F rotational moulded polyethylene water storage tank including plastic lid cover, double layered, cylindrical vertical with closed top hoisted and fixed in position of capacity 1000 ltrs including making connections, 20 mm dia ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (min wt 210 gram) complete all as specified in SSR Part-I.

S&F in repairs Ball valves high pressure of PTMT with epoxy coated aluminium rod and high-density plastic ball screwed for iron pipe and fixed (minimum weight 15mm-142 gms) of 15 mm bore complete all as specified and as directed.

S&F in repairs 20 mm dia Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (min wt 210 gram), screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Repairing of existing float valve by replacing its rod of brass or plastic float of any description complete all as specified and as directed at site.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water and removing unserviceable material outside cantt area all as specified and directed by Engr-in-Charge. Note: Plaster work may be in patches upto triple storey.

M&L rendering 10 mm thick in CM 1:6 on fair faces of brick surface finished even and smooth without using extra cement upto height of four storey building all as specified and as directed.

M&L rendering 5 mm thick in CM 1:3 on fair faces of concrete surface of ceiling, finished even and smooth without using extra cement, all as specified and as directed by Engineer-in-Charge.

M&L rendering 15mm thick in CM 1:4 in two layers of 10 mm thick and 5 mm thick with WPC on fair faces of brick surface finished even and smooth without using extra cement etc. all as specified and as directed. (Including all necessary scaffolding lifiting arrangement for external surfaces).

M&L for two coats of oil bound distemper to newly plastered surfaces including preparation of surfaces complete all as specified and directed by Engr-in-Charge.

M&L applying two coats of cement based paint including preparation of new plastered surface complete all as specified and as directed.

Complete removal of existing treatment and applying two coat of apex paint on old surface of chajjas including preparation complete all as specified and as directed.

Complete removal of existing treatment of old surface of wall (plastered or unplastered) and applying one coat of cement base paint complete all as specified and as directed.

M&L for two coats of oil bound distemper of wall to old plastered surfaces including preparation of surfaces complete all as specified and directed.

M&L applying three coats of white wash on ceiling including preparation of newly plastered surface complete all as specified and as directed.

Dismantling floors, hearth or wall tilling including cement mortor bedding (but not backing) removing unserviceable materials outside MOD area and rubbish off the premises complete all as specified and as directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Description same as per Ser item No 72.00 here-in-before but as in skirting including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L Vitrified tiles dark shade 10mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including screed bed 15mm thick in CM 1:4 complete all as specified and directed.

M&L Vitrified tiles dark shade 10mm thick (square / rectangular) polished, area of each tiles not exceeding 0.36 sqm, as on vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade over and including 10 mm thick screed in CM 1:4 complete all as specified and as directed.

M&L glazed ceramic coloured tiles 300 x 450 x 7 to 8 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the surface over and including taking down old plaster and 10 mm thick screed in CM 1:4 complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc all as specified and directed.

M&L granite 20mm thick (Pure black) (tabled rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar 1:4 including pointing in colour cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in cm 1:4 edges of slab to be rounded from all sides (including cutting, wastage and polishing) complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

S&F in repairs chromium plated bib tap 15mm size with crutch or butterfly handle screwed down screwed fro iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F plain aluminium sheeting 0.71 mm thick, in crumple joint covering, ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed.

S&F angle / stop valve of cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed 15 mm bore complete all as specified and as directed.

S&F swivel shower rose PTMT any colour with arm 15mm size 195mm long complete all as specified and as directed.

Dismanting asbestos cement (corrugated or semi corrugated etc) sheets in roof covering complete all as specified and as directed.

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets fixed with L-type or J-type or cranked hook bolts in roofs, walls etc complete all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and as directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and as directed.

Dismantling timber scantling 40 sq cm and over in section framed work of any description complete all as specified and as directed.

S&F for structural steel works of Fe-410W (Gde 'E' 250) quality 'A', as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate / red oxide primer paint (including preparation of surface) before fabrication including taking down complete all as specified and as directed.

Dismantling boarding of any description fixed in any position with nail complete all as specified and as directed.

S&F for frame work for ceiling with specification as under mentioned:- (i) GI section frame work (Powder coated) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mm X 19mm X 0.45mm, cross 'Tee' 28.6mm (web) X 24mm flange 0.33mm thick powdered coated main tee 38mm (Web) X 24mm flange 0.33mm thick. Wall angle shall be screwed / fixed to brick wall / partition wall / concrete / RCC with the help of nylon sleeves and screws @ 610 mm C/C, then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits. To from grid of 610X610mm cross Tee shall be provided @ 610mm C/C in both directions and all suitable provisions shall be made for fixing the recessed / surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge.

S&F for 4mm thick of size 605 X 605 mm, white pre-premiered, self embossed, reinforced Designer board for false ceiling conforming to IS-14862 and ISO-8336:1993 fixed / laid / inserted to GI framework at ceiling with screws complete all as specified and as directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surface all as specified and directed.

S&F PVC connection 15mm, 450mm long with nuts and washers complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in floor / plinth protection laid in suitable panels finished even and fair all as specified. 6mm joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 gde and three part of sand (all by weight) complete all as specified and as directed.

M&L for double action floor spring hydraulically regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repairs all as defined complete all as specified and as directed.

Repair to Aluminium door including adjusting, necessary bedding, clip, rubber beader, repair to floor door closer complete all as specified and as directed.

S&F Aluminium (extruded section) body door closer hydraulically regulated designation No 2, universal type suitable for door shutters of 701 to 850mm in width and of weight between 36 and 60kg and fixed in repairs complete all as specified and as directed.

S&F in repairs waste coupling of PTMT (half or full threaded) of bore dia 32 mm discharge pipe complete all as specified and as directed.

Material and Labour for repairing of existing Bib cock by replacing its jumper / washer etc to make it functional complete all as specified and as directed at site.

S&F brass phase for CP bib tap, pillar tap, angle valve for suitable 15mm dia full turn, half turn as per sample all as specified and as directed. Make: - Jaquar, Cera, Kohler

S&F grating doom 100mm dia without hole chromium plated complete all as specified and as directed.

S&F grating doom 100mm dia with hole, chromium plated complete all as specified and as directed.

S&F 15mm bore long body bib tap cast copper alloy fancy type chromium plated with capstan handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and as directed. as per sample kept in AGE B/R Damana office.

S&F PVC waste pipe 32 mm dia and suitable length straight or flexible type for wash hand basin / sink complete all as specified and as directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length of cover plate as 150mm complete all as specified and as directed.

S&F PVC tank cover for water storage tank for 500 ltr capacity including locking arrangement complete all as specified and as directed.

S&F in repair 110 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall complete all as specified and as directed.

S&F in repair 75 mm dia bore PVC (SWR) pipes single socketed in any length with solvent cement joints, fixed to wall complete all as specified and as directed.

S&F in repairs PVC SWR bends of bore 110mm dia complete all as specified and directed.

S&F in repairs PVC SWR bends of bore 75 mm dia complete all as specified and directed.

Note:- Providing one Plumber and his helper with M.seal, taflon tape, white cement and similar items etc for plumbing works and one carpenter and his helper with nails/screw of different size, fevicol, pvc rawal plug and similar items etc for carpenter work with tools and plant required for day to day maintenance and petty repair required for upkeeping of certain pocket of Married/ OTM Accn buildings under AOR of AGE B/R Damana for 08 (eight) working hours (0900 - 1700 Hrs) per day, and reporting to JE (Civil) incharge after attending the complaint at 16.00hrs daily. including provision of uniform along with all necessary tools, to the persons providing services complete all as per requirement enumerated in Particular Specifictions and as directed at site by the Engineer-In-Charge.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - All plumbing works shall be laid or fixed as to be completely air tight or water tight as specified and Contractor will furnish its certificates towards air / water tight before completion of work under the Contract. NOTE NO 4: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

Jagbir Singh and Co

Mehta Enterprises

M/S STAR CONSTRUCTIONS

ASHFAQ AHMED MANHAS

Bidder Name

ASHFAQ AHMED MANHAS

M/S VERMA ENTERPRISES

Jagbir Singh and Co

Mehta Enterprises

M/S STAR CONSTRUCTIONS