8414-REPAIR/ REPLACEMENT AND PAINTING OF DIFFERENT STEEL AND WOODEN FURNITURES OF OFFRS MD ACCN UNDER GE MINNIE BAY PORT BLAIR

Amount

BED HARD/BED PLY TOP (1980mmx900mmx660mm) FD-246/ 247

S&F 12mm thick plywood BWP Grade,termite and borer resistant, approved quality in single piece as per drawing without any joint to the bed frame with suitable screws wood/steel including removal of damaged ply wood complete all as specified and directed by Engineer-in-Charge.

S&F in repairs to 1st quality seasoned grade 1 teakwood long rail 35mm x 90mmx 1930mm in section as per existing size of Bed including removal of damaged long rail all as specified on drawing or as directed by Engineer-in-charge.

All as per item No. 1.02, but short rail 60mm x60mmx 900mm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs to head board consisting of 60 x 30 x 260mm vertical size and 30 x 60 x 400mm horizontal including legs of size 60 x 60mm in section at top and length 400mm from bottom of leg and 30 x 30mm in section at bottom complete including removal of damaged head board all as specified on drawing or as directed by Engineer-in-charge.

All as per item No. 1.04, but foot board consisting of 22 x 75mm in section seasoned grade 1 teakwood battens 3 Nos at equal space, joining top and bottom horizontal rails of foot board. The top and bottom horizontal rails of size 30 x 60mm shall be 1st quality of seasoned grade 1 teakwood. The vertical legs above horizontal rails shall be 30 x 60mm all as specified on drawing or as directed by Engineer-in-charge.

S&F in repair with new 1st quality seasoned grade 1 teakwood stiffeners of size 40mm x 60mm x 900mm complete including removal of damaged stiffiners all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs 4mm thick one side seasoned grade 1 teakwood finished plywood BWP grade of size 780 x 340mm including 12mm dia half cut seasoned grade 1 teakwood beading of both side of head board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to 4mm thick one side seasoned grade 1 teakwood finished plywood BWP grade of size 780 x 180mm including 12mm dia half cut seasoned grade 1 teakwood beading of both side of foot board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to flat iron of mild steel of size 15mm x80mm x 3mm, bents to right angle on each corners of Bed Hard all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mansion wax polish till the smooth finishing achieved complete all as specified and directed by Engineer-in-charge.

BIN SOILED LINEN SMALL (750mm x 45mm x 450mm) FD-244

Material and labour for replacement of unservicable Top of 6mm of 450mm x 900mm size with new 6mm pre-laminated particle board exterior grade

S&F in repairs to unserviceable damaged legs from bin soiled linen small made out of hard wood (seasoned grade 1 teakwood) complete, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged legs ( 45x 45mm at top and 45 x 25mm at bottom) from bin soiled linen small made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged front side from bin soiled linen small made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged bottom from bin soiled linen small made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

Recaning of repaired Bin soiled linen on (Left Right) both sides with best quality of approved plastic cane 2mm wide 0.4mm thick cane and border with 3x0.60 mm cane of white or cream ivory all as specified and directed by Engineer-in-charge. (Note: Each side wil be mesured as single unit).

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mansion wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

CHAIR DINING (440MMx430MMx890MM) FD-228, FD-279 FD MAP-II/04

Removing the existing unserviceable rear leg and providing with new seasoned grade 1 teakwood rear leg of size 30x55x890 mm complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new seasoned grade 1 teakwood front leg of size 30x55x460mm complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable back rest and proving new seasoned grade 1 teakwood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new seasoned grade 1 teakwood front rail of size 30x65mm drilling 3mm dia holes at 12.5 mm C/C complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable rear rail of size and proving new seasoned grade 1 teakwood rear rail of size 30mm x 65mm including drilling 3mm dia holes at 12.5 mm C/C complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new seasoned grade 1 teakwood side rails of size 30x65 mm including drilling 3mm dia holes at 12.5mm C/C complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable fabric leatherette seat and cushion providing new fabric leatherette seat and cushion 75 mm thick 40 mm density foam cover with leatherette seat and 12 mm BWP ply wood shall be approved by GE

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mansion wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

CHAIR WRITING (530MMx470MMx890MM) FD-280

Removing the existing unserviceable rear leg and providing with new seasoned grade 1 teakwood rear leg of size 55x30x890mm complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new seasoned grade 1 teakwood front leg of size 55x30x685mm complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable back rest and providing new seasoned grade 1 teakwood back rest of size 50 x 15mm slightly curved made out of 50x35mm complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new seasoned grade 1 teakwood front rail of size 30x65mm including drilling 3mm dia holes at @ 12.5 mm C/C complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable rear rail and providing new seasoned grade 1 teakwood rear rail of size 30x65mm including drilling 3mm dia holes @ 12.5 mm C/C complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

(Removing the existing unserviceable side rails and providing new seasoned grade 1 teakwood side rails of size 30x65mm including drilling 3mm dia holes @ 12.5mm C/C complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest of size 60x25 mm of appropriate length and providing new seasoned grade 1 teakwood arm rest complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Recanning of repaired chair writing with best quality of approved plastic cane 1.80 x0.46mm cane (godrej pattern) and border with 3x0.60mm cane of white or cream/ivory all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mansion wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

CHAIR EASY FD-229

Removing the existing unserviceable rear leg and providing with new seasoned grade 1 teakwood rear leg of size 55x25 mm of appropriate length complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new seasoned grade 1 teakwood front leg of size 55x25mm complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest and providing new seasoned grade 1 teakwood arm rest of size 65x25x610mm complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable front frame and providing new seasoned grade 1 teakwood front frame of size 55x25 mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new seasoned grade 1 teakwood front rail of size 50x25 mm of appropriate length complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable rear rails and providing new seasoned grade 1 teakwood rear rails of size 50x25mm of appropriate length complete all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Recaning of repaired chair easy seat and back of approved quality white or cream ivory with 1.80 x 0.46 mm cane and border with 3x0.60 mm cane Godrej pattern complete all as specified on drawing all as specified and directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mansion wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

COMMON FOR ALL CHAIRS FD-228/ 279/280/225/285 or similar

Removing the existing unserviceable stiffeners and providing new seasoned grade 1 teakwood 2nd class hard wood stiffeners of size 25x20 mm .

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

PEG TABLE FD-277

M & L for removing the existing unserviceable leg and providing with new seasoned grade 1 teakwood rear leg 30mm x 50mm x 380mm complete all as specified on drawing or as directed by Engineer-in-charge.

M & L for removing the existing unserviceable top rail and providing with new seasoned grade 1 teakwood top rail 20mm x40mm of appropriate length complete all as specified on drawing or as directed by Engineer-in-charge.

M & L for removing the existing unserviceable bottom rail/ stiffener of 20mm x 40mm of appropriate length and providing with new seasoned grade 1 teakwood bottom stiffener complete all as specified on drawing or as directed by Engineer-in-charge.

Replacement of old unserviceable top with new 19mm prelaminated particle board exterior grade complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

SOFA SET 5 SEATER FD-281 & 373

Removing the existing unserviceable tapestry cloth, cushion of sofa set 5 seater and replacing with new tapestry cloth including mulmul with foam cushion 40 density 100mm thick of size 560mm x 530mm x 100mm. The tapestry cloth shall be matt finish and shall not less than Rs. 350/- per metre and as approved by GE. , rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing the existing unserviceable front leg from Sofa and providing new first class seasoned grade 1 teakwood of leg size 70mm x 35 mm x 300mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing the existing unserviceable rear leg from Sofa and providing new first class seasoned grade 1 teakwood leg size 70mm x 35 mm x 530mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable Arm rest from Sofa and providing new first class seasoned grade 1 teakwood Arm Rest of size 35mm x 70mm x 725mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable side rail from Sofa and providing new first class seasoned grade 1 teakwood side rail of size 35 mm x 100mm x 725mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable bearer from Sofa and providing new first class seasoned grade 1 teakwood bearer of size 40mm x 40mm x 725mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable battens from Sofa and providing new first class seasoned grade 1 teakwood battens of size 50mm x 20 mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable front rail from Sofa three seater and providing new first class seasoned grade 1 teakwood front rail of size 35mmx 100mm x 1590 mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable front rail from Sofa single seater and providing new first class seasoned grade 1 teakwood front rail of size 35mm x 10mm x 530 mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

SOFA SET 4 SEATER FD-281 & 373

Removing the existing unserviceable tapestry cloth, cushion of sofa set 4 seater and replacing with new tapestry cloth including mulmul with foam cushion 40 density 100mm thick of size 560mm x 530mm x 100mm. The tapestry cloth shall be mat finish and shall not less than Rs. 350/- per metre and as approved by GE. , rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing the existing unserviceable front leg from Sofa and providing new first class seasoned grade 1 teakwood of leg size 70mm x 35 mm x 300mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing the existing unserviceable rear leg from Sofa and providing new first class seasoned grade 1 teakwood leg size 70mm x 35 mm x 530mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable Arm rest from Sofa and providing new first class seasoned grade 1 teakwood Arm Rest of size 35mm x 70mm x 725mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable side rail from Sofa and providing new first class seasoned grade 1 teakwood side rail of size 35 mm x 100mm x 725mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable bearer from Sofa and providing new first class seasoned grade 1 teakwood bearer of size 40mm x 40mm x 725mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable battens from Sofa and providing new first class seasoned grade 1 teakwood battens of size 50mm x 20 mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable front rail from Sofa three seater and providing new first class seasoned grade 1 teakwood front rail of size 35mmx 100mm x 1590 mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing existing unserviceable front rail from Sofa single seater and providing new first class seasoned grade 1 teakwood front rail of size 35mm x 10mm x 530 mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

TABLE DRESSING GENTS FD-230

Replacement of existing unserviceable drawer for Table dressing gents made out of prelaminated particles board 12mm thick of 255mm x 300mm x150mm compartment size one side seasoned grade 1 teakwood facing and balancing white on the other side and 12x12mm wooden beading around all as specified and directed by Engineer-in-charge. Note-Each drawer should be measured as single unit

S & Fixed in repairs new mirror 5.5mm thick of approved make with full frame all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new top made out of 12mm thick pre laminated particle board of 900mm x300mm of approved make, all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

TABLE DRESSING LADIES FD-251

S & Fixed in repairs table top of Table dressing ladies with 19 mm thick pre-laminated particle Board of approved make, all as specified on drawing or as directed by Engineer-in-charge.

S&Fixed in repairs new 5.5mm sliding glass shutters of size 550mm x 300mm of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge.(Each glass shutter shall be measured as single unit)

Removing the existing unserviceable Aluminium channel and S & Fixed in repairs 12mm x 22mm aluminium Channel all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new back support made out of 6 mm thick plywood BWP grade for mirror of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new mirror 5.5mm thick for Table dressing ladies of approved make with complete frame back all as specified on drawing or as directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

Table Bed Side FD-276

Removing of existing unserviceable sides of Table Bed Side and providing new sides of 19mm thick prelaminated particle Board with seasoned grade 1 teakwood veneer facing one side and balancing white on the other side of exterior grade and 18 x 6 mm seasoned grade 1 teakwood beading on front sides, rest all as specified and directed by Engineer-in-charge. (Each sides will be measure as single unit)

Removing of existing unserviceable Top and bottom of Table Bed Side and providing new Top of 19mm thick prelaminated particle Board with seasoned grade 1 teakwood veneer facing one side and balancing white on the other side of exterior grade and 18 x 6 mm seasoned grade 1 teakwood beading on front sides, rest all as shown on drawing and as directed by Engineer-in-Charge. (Each Top & Bottom will be measure as single unit)

Removing of existing unserviceable Back of Table Bed Side and providing new Back of 6mm plywood commercial shall be fixed with headless nail, rest all as shown on drawing and as directed by Engineer-in-Charge.

SIDE BOARD (1200mm x 455mm x 760mm) FD-241

Removing the existing unserviceable top of side board and providing new top made out of 19mm thick prelaminated particle board exterior grade of size 1220 x 455 mm all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable sides of side board and providing new sides made out of 18mm thick prelaminated particle board exterior grade of size 760x 455mm all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge. (Note : Each side will be measured as single unit)

Removing the existing unserviceable back of Side Board and providing new Back with 6mm thick plywood commercial type of Size 760 x 1220 mm all as specified on drawing all as specified and directed by Engineer-in-charge.

Removing the existing unserviceable Top drawer and providing New drawer made out of 12 mm thick particle board having ply on both sides. The drawer shall be run as 19 mm x 19 mm thick seasoned grade 1 teakwood batten all as specified on drawing all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable Drawers (other than Top drawers) and providing new drawer made out of 12mm thick particle board having ply on both sides. The drawer shall be run as 19mm x 19mm thick seasoned grade 1 teakwood bearer all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge. Note : Each drawer will be measured as single unit.

Removing the existing unserviceable shutter and providing new shutter made out of 19mm thick teak veneer on one side and white on other side ply of size 400x600 mm including Hinges and lock all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge. (Note : Each shutter will be measured as single unit.

Removing the existing unserviceable bottom of side board and providing new bottom of size 1220 x 455 mm made out of 19mm thick plywood commercial type all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable leg frame of side board and providing seasoned grade 1 teakwood 2nd class hard wood leg frame all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removing the existing unserviceable broken legs of side board and providing new seasoned grade 1 teakwood leg 2nd class hard wood of size 45 x 45 x 125 mm but at bottom 25 x 25 mm all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge. Note : Each leg will be measured as single unit.

Replacement of unserviceable hinges with new continuous 75mm long piano hinges of appropriate length.

S & Fixed in repairs locking device 1st quality brass 6 lever locks iron body with duplicate keys chromium plated all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

TEAPOY WOODEN FD-278 / 382

Replacement of existing unserviceable top for Teapoy made out of pre laminated particle board 19mm thick with one side seasoned grade 1 teakwood facing and balancing white with on the other and fixed with 19x12mm wooden beading (seasoned grade 1 teakwood) on all the four sides all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

S&F in repairs of old unserviceable damaged legs from teapoy with new one 30mm x 60mm x 540mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs of unserviceable damaged bottom stiffeners (both short & long) from teapoy with new one of 30mm x 60mm of 600/450mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

TABLE DINING 8/6 PERSONS FD-273

S&F in repairs of unserviceable damaged legs from Table dining 8/6/4 persons made out of 75mm x 40mm of length 760mm hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs of unserviceable damaged side short rails from Table dining 8/6/4 persons made out of 25mm x100mm of length 900mm hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged long rails from Table dining 8 persons made out of 25mm x100mm of length 1500/1800mm hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

Replacement of existing unserviceable table top for Table dining 8 persons made out of prelaminated particle board 19mm thick 1800mm x 900mm size with one side seasoned grade 1 teakwood facing and balancing white on the other side and fixed with 18x12mm wooden beading (seasoned grade 1 teakwood) on all the four sides all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Replacement of existing unserviceable table top for Table dining 6 persons made out of prelaminated particle board 19mm thick 1500mm x 900mm size with one side seasoned grade 1 teakwood facing and balancing white on the other side and fixed with 18x12mm wooden beading (seasoned grade 1 teakwood) on all the four sides all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged long rails from Table dining 6 persons made out of 25mm x 100mm of length 900mm hard wood (seasoned grade 1 teakwood) , rest all as shown on drawing and as directed by Engineer-in-Charge.

Replacement of existing unserviceable table top for Table dining 4 persons made out of prelaminated particle board 19mm thick with one side seasoned grade 1 teakwood veneer facing and balancing white on the other side and fixed with 18x12mm wooden beading (seasoned grade 1 teakwood) on all the four sides all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged long rails from Table dining 4 persons made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

Hat Stand with mirror FD-361/362

S & Fixed in repairs new mirror 5.5mm thick for Hat stand with mirror of approved make with complete frame back all as specified on drawing or as directed by Engineer-in-charge.

Removing of existing unserviceable Back of Hat stand with mirror and providing new Back of 6mm plywood commercial shall be fixed with headless nail, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F of brass pegs with brass screw in place of broken/ lost pegs in hat stand with mirror, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

TABLE WITH DRAWER 900x 600 x 760mm FD-283

Removing of existing unserviceable table top for Table with drawer 900 x 600 x 760mm and providing new table top made out of 19mm thick prelaminated particle board with seasoned grade 1 teakwood veneer facing one side and balancing white on the other side of exterior grade and 18 x 4 mm seasoned grade 1 teakwood beading on all round, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged legs from Table with drawer size 30x60x760mm made out of hard wood (seasoned grade 1 teakwood) size 60x30x760mm rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table with drawer size 20x110x600mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged front long rails from Table with drawer size 20x110x900mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffeners (short side) from Table with drawer size 25mm x 60mm x 600mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged drawers from Table with drawer 900x600x760mm made out of hard wood (seasoned grade 1 teakwood) including providing 6mm thick commercial ply to bottom of drawer complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

TABLE WITHOUT DRAWER 900x 600 x 760mm FD-284

Removing of existing unserviceable table top for Table without drawer 900 x 600 x 760mm and providing new table top made out of 19mm thick prelaminated particle board with seasoned grade 1 teakwood veneer facing one side and balancing white on the other side of exterior grade and 18x4 mm seasoned grade 1 teakwood beading on all round, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged legs from Table without drawer 900x600x760mm made out of hard wood (seasoned grade 1 teakwood) size 60x30x760mm including applying two coats of French polish including preparation of surfaces complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table without drawer size 20x110x600mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged front long rails from Table without drawer size 20x110x900mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffeners (short side) from Table with drawer size 20mm x 60mm x 600mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffeners (long side) from Table with drawer size 20mm x 60mm x 900mm made out of hard wood (seasoned grade 1 teakwood) complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

TABLE 900x 900 x 760mm FD-291

Removing of existing unserviceable table top for Table 900 x 900 x 760mm and providing new table top made out of 19mm thick prelaminated particle board with seasoned grade 1 teakwood veneer facing one side and balancing white on the other side of exterior grade and 18x4 mm seasoned grade 1 teakwood beading on all round, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs to unserviceable damaged legs from Table 900x900x760mm made out of hard wood (seasoned grade 1 teakwood) size 60x30x740mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

STOOL DRESSING CB, FD-282

Removing of existing unserviceable legs of stool dressing and providing with new legs of 1st quality seasoned grade 1 teakwood of size 50 x 30 x 380mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing of existing unserviceable side rails of stool dressing and providing with new side rails of1st quality seasoned grade 1 teakwood of size 25 x 50 mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removing of existing unserviceable front and rear rails of stool dressing and providing with new front and back of1st quality seasoned grade 1 teakwood of size 25 x 65 mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

Replacement of existing unserviceable plastic cane of Stool dressing and recanning the same with half round 2mm wide and 0.4mm thick plastic cane Godrej pattern, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of french polish over a coat of mention wax polish till the smooth finishing complete all as specified and directed by Engineer-in-charge.

Almirah Large/Glazed/Medium / Small Steel FD-67 / 104 350/351/1031/ 1033,FD-114(m), FD-243 FD-1032, FD-1034

S&F in repairs legs of Almirah Large/Glazed steel and providing new legs of 100mm height made out from 1mm MS channel base ends covered into required shape for almirah large/Glazed steel, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs legs of Almirah medium/small and providing new legs of 100mm height made out from 1mm MS channel base ends covered into required shape for almirah large/Glazed steel, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs shelves for Almirah Large/Glazed steel with MS sheet CRC 1mm thick bent to shape including welding to the almirahs, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs shelves for Almirah Medium/Small steel with MS sheet CRC 1mm thick bent to shape including welding to the almirahs, rest all as shown on drawing and as directed by Engineer-in-Charge.

S & F in repairs locking device including replacement of brass 6 lever locks iron body with duplicate keys chromium plated to Almirah Large/Glazed/Medium/Small steel , rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs handle Chromium plated of size 150 mm grip length with both sides screwed to Almirah large/Glazed/Medium/small steel , rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repair to door shutter of Almirah Large/Glazed/medium/small steel with 1mm thick MS sheet including replacement of hinges all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs Almirah glazed steel by removing of existing unserviceable mirror plain neatly and replacing the new mirror plain 5.5mm thick with suitable bolts and clamps to be fitted or welded where ever required, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F existing serviceable shelf with proper welding to reposition in almirah

Removal of existing worn out painting from in side & outside including preparation of surface frame and applying two coats of 1st quality synthetic enamel paint of approved colour and make over a coat of red oxide primer, complete all as specified and directed by Engineer-in-Charge.

Chair computer Revolving (MAP and similar)

S & F in repairs of maintenance free Gas lift for all type of chairs revolving rest all as shown on drawing and as directed by Engineer-in-Charge.

S & F in repairs of Pedestal assy. Injection moulded in black 30% glass filled nylon , 50mm MS castor pin is of press fitted to each prong for holding the castor, for all type of chairs revolving rest with pitch center dia of 600mm all as shown on drawing and as directed by Engineer-in-Charge.

S & F in repairs of twin wheel castors for all type of chairs revolving rest all as shown on drawing and as directed by Engineer-in-Charge.

S & F in repairs of seat not less than size 510x470x60mm and back made out from 12mm thick hot pressed plywood upholstered with fabric and moulded polyurethane foam with acrylic/polyester and the back foam designed with lumbar support with PVC lipping and as directed by Engineer-in-Charge.

S & F in repairs removing of old upholstery from seat and back of all type of chairs with new best quality Acrylic/polyester fabric complete including upholstery work for all type of chairs revolving rest all as shown on drawing and as directed by Engineer-in-Charge.

S & F in repairs of handles of chair revolving made of black integral skin polyurethane reinforced with MS insert scratch proof weather and scratch resistant complete for all type of chairs revolving with arm rest all as shown on drawing and as directed by Engineer-in-Charge.

CHAIR TUBULAR STEEL WITH ARMS FD-75 (M)

Repairs/ replacement of seat frame made out of superior quality hard wood 35x25mm size duly black painted and caned Godrej pattern for tubular steel chair CB with arms of overall size of seat frame 450x450mm, rest all as shown on drawing and as directed by Engineer-in-Charge.

Repairs/ replacement of back rest frame made out of superior quality hard wood 35x25mm size duly black painted and caned Godrej pattern for tubular steel chair CB with arms of overall size of seat frame 450x380mm rest all as shown on drawing and as directed by Engineer-in-Charge.

Replacement of hand rest (Godrej pattern) duly painted with black enamel paint as per existing size for tubular steel chair tubular steel with arms rest all as shown on drawing and as directed by Engineer-in-Charge.

Repair/replacement of Flat iron strips 20mm x 3mm, two in numbers in each seat and back, shall be welded to frame of chair, rest all as shown on drawing and as directed by Engineer-in-Charge.

CHAIR TUBULAR STEEL WITHOUT ARMS FD-75 (M)

Repairs/ replacement of seat frame made out of superior quality hard wood 35x25mm size duly black painted and caned Godrej pattern for tubular steel chair CB without arms of overall size of seat frame 450x380mm rest all as shown on drawing and as directed by Engineer-in-Charge.

Repairs/ replacement of back rest frame made out of superior quality hard wood 35x25mm size duly black painted and caned Godrej pattern for tubular steel chair CB without arms of overall size of seat frame 450x380mm rest all as shown on drawing and as directed by Engineer-in-Charge.

Repair/replacement of Flat iron strips 20mm x 3mm, two in numbers in each seat and back, shall be welded to frame of chair, rest all as shown on drawing and as directed by Engineer-in-Charge.

CHAIR VERANDAH FD-19, FD-256, FD-359, FD/MAP-II/15

Repair/replacement of broken Leg, each one piece made of MS conduit pipe 16G, 19/20mm dia including welding and providing two coats of synthetic enamel paint over one coat of red oxide primer all as per drawing and as directed by Engineer-in-charge.

Material and Labour for welding joints of broken leg with 19/20mm Mild Steel tubes ISI marked & other joints complete all as specified and directed by Engineer-in-Charge.

Material and Labour for hard PVC/Nylon shoes complete all as specified and directed by Engineer-in-Charge.

M&L for removal of existing worn out paint surfaces and two coats of the entire frame of chair verandah with white colour synthetic enamel paint over a coat of primer of approve make including removing old unserviceable cane/plastic newar from seat & back and recaning the seat & back of complete chair including handles etc with approved 4mm white plastic cane as per Matt Pattern all specified on drawing or as directed by Engineer-in-charge.

CHARPOY GI PIPE /RECTANGULAR PIPE WITH PLYWOOD TOP FD-220

S&F in repairs to 12mm thick plywood BWP Grade, single piece of approved quality with suitable steel screw and cup washer including removal of damaged plywood, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&Fixed in repairs GI Elbow 32 mm dia three way medium grade, duly threaded and as directed by Engineer-in-Charge.

S & Fixed in repairs 32mm medium grade 1980mm long rail for GI Charpoy including removing unserviceable long rail, rest all as shown on drawing and as directed by Engineer-in-Charge.

Making 32mm GI pipe short rail of length 900mm for GI Charpoy obtained from Sch 'A' item No.26.03 here-in-before cut in to length one end threaded including removing of existing unserviceable short rails all as specified and directed.

Making 32mm dia GI leg of length 440mm for GI charpoy obtained from item No. 26.04 above here-in-before end threading other end plugged with wooden stopper rest all as shown on drawing and as directed by Engineer-in-Charge.

Supply & fixing three Nos & 25 mm mild steel flat iron 16 gauge not less then 80 cm long each welded to charpoy GI at equal distance as in centre support at middle span including painting all as specified & directed.

Table Office Officers Steel FD-84 (M)

S&F in repairs drawers made of 20 gauge MS Sheet duly finished with standard workmanship for Table Office Officers Steel complete same as per existing drawer, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs top of Table office officer steel top with 19mm thick prelaminated particle board one side seasoned grade 1 teakwood facing and balancing white on other side all the four edges provided with suitable PVC beading, rest all as shown on drawing and as directed by Engineer-in-Charge.

S & F MS Lock (6 liver brass levers) with duplicate keys for drawers/cup-board, rest all as shown on drawing and as directed by Engineer-in-Charge.

M & L for welding of broken joints 25mm to 75mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M & L for repair including welding and replacement of heavy duty spring with new as per existing locking device to make functional for smoothly play of drawers in its original position, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F of leg Made out of square pipe 25mm square pipe having wall thickness 1.6mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F Hard Rubber/PVC toe of superior quality as approved & as directed by Engineer-in-charge.

Removal of existing worn out painted surfaces and applying paint to the entire frame of table with two coats of white colour synthetic enamel paint over a coat of primer of approve make all specified on drawing or as directed by Engineer-in-charge.

Table Office Clerk Steel FD-84 (M)

S&F in repairs drawers made of 20 gauge MS Sheet duly finished with standard workmanship for Table Office Clerk Steel same as per existing drawer complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repairs top of Table office clerk steel top with 18mm thick prelaminated particle board one side seasoned grade 1 teakwood facing and balancing white on other side all the four edges provided with suitable PVC beading, rest all as shown on drawing and as directed by Engineer-in-Charge.

S & F MS Lock (6 liver brass levers) with duplicate keys for drawers/cup-board, as per approved sample & as directed by Engineer-in-charge.

M & L for welding of broken joints 25mm to 75mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M & L for repair including welding and replacement of heavy duty spring with new as per existing locking device to make functional for smoothly play of drawers in its original position, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F of leg Made out of MS square pipe 25mm square pipe having wall thickness 1.6mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F to Hard Rubber/PVC toe of superior quality as approved & as directed by Engineer-in-charge.

Removal of existing worn out painted surfaces and applying paint to the entire frame of table with white colour synthetic enamel paint over a coat of primer of approve make including removing old unserviceable PVC Seat from seat & back and new PVC seat provide seat & back of complete size of seat PVC 90x10 mm and 4 mm thick not less than 1.85 KG all specified on drawing or as directed by Engineer-in-charge.

TABLE 900x900x600 mm STEEL FD-291

Replacement of existing unserviceable table top for Table 3'x3' Steel made out of 18mm thick pre-laminated particle board with seasoned grade 1 teakwood finish one side and balancing white on the other side and 18 x4 mm wooden beading (seasoned grade 1 teakwood) on all the four sides complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F of leg Made out of square pipe 25mm square pipe having wall thickness 1.6mm complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M&L for welding of broken joints 25mm to 75mm of Table 3'x3' Steel , rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F Hard PVC/rubber toes of superior quality as specified and as directed by Engineer-in-charge.

Removal of existing worn out paint and Re-Painting to the entire frame of table with white colour synthetic enamel paint over a coat of primer of approve make including removing old unserviceable PVC Seat from seat & back and new PVC seat provide seat & back of complete size of seat PVC 90x10 mm and 4 mm thick not less than 1.85 KG all specified on drawing or as directed by Engineer-in-charge.

Locker Steel FD-257,FD-1029

S&F in repair to leg made out of 1mm MS Sheet complete rest all as shown on drawing and as directed by Engineer-in-Charge.

S&F in repair to MS butt Hinges 75mm long

S&F in repair to Chromium plated Handle 100mm long

S&F in repair to Chromium plated Hasp & Staple of size 75mmx40mmx3mm

S&F in repair to 20mm Chromium plated hanging pipe of wall thickness 1.25mm including replacement of brackets complete all as shown in drawing of as directed by GE/Engineer-in-charge.

M & L for welding of broken joints 25mm to 75mm long of Locker Steel complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

Removal of existing worn out painted surfaces and applying to the entire frame of locker with two coats of white colour synthetic enamel paint over a coat of primer of approve make including removing old unserviceable PVC Seat from seat & back and new PVC seat provide seat & back of complete size of seat PVC 90x10 mm and 4 mm thick not less than 1.85 KG all specified on drawing or as directed by Engineer-in-charge.

Teapoy verandah FD-255

Replacement of frame of top (without top) of Teapoy Verandah and applying two coats of synthetic enamel paint white colour over a coat of red oxide primer complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

M & L for welding of broken joints of Teapoy verandah including preparation of surface and applying two coat of white synthetic enamel paint over a coat of red oxide primer complete, rest all as shown on drawing and as directed by Engineer-in-Charge.

Replacement of existing unserviceable table top for Teapoy verandah made out of 18mm thick pre laminated particle board seasoned grade 1 teakwood finish on top and balancing white with on the other and all the four edges provided with suitable PVC beading all as specified on drawing all as specified and directed by Engineer-in-charge. directed by Engineer-in-charge.

Removal of existing worn out paint and Re-Painting to the entire frame of chair verandah with white colour synthetic enamel paint over a coat of primer of approve make including removing old unserviceable PVC Seat from seat & back and new PVC seat provide seat & back of complete size of seat PVC 90x10 mm and 4 mm thick not less than 1.85 KG all specified on drawing or as directed by Engineer-in-charge.

Table Bed side steel FD-157 (M) & FD/ E6/ MAP/ 15 R

Removal of existing worn out painting from in side & outside including preparation of surface frame complete of the following steel furniture and M&L for applying two coats of 1st quality synthetic enamel paint of approved colour and make over a coat of red oxide primer, rest all as shown on drawing and as directed by Engineer-in-Charge.

Replacement of existing unserviceable table top for Table bed side steel made out of 18mm thick prelaminated particle board exterior grade with suitable PVC edging al-round top of table, rest all as shown on drawing and as directed by Engineer-in-Charge.

M/s Susanta Enterprises (BID ID -3062264)

SALCON ENGINEERS AND FABRICATORS (BID ID -3062332)

Chandra Construction Enterprises (BID ID -3061685)

MAJUMDAR FURNITURE (BID ID -3062639)