Park inside the Honble Ministers Colony

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

REINFORCED CEMENT CONCRETE WORKS: Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

FORM WORK: Centering and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster.

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

Demolishing R.B. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

FORM WORK: Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)

20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): Raised and cut pointing

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : Makrana white second quality

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size. Size of Tile 600 x 600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Extra for pre finished nosing to treads of steps of marble stone

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 100 mm nominal dia Pipes

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall. 25 mm dia nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 20 mm nominal dia Pipes

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm .................... as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & ...................water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing, fitting and fixing Certain Teed Designer Roofing made of composite fiber glass shingles, Type: Landmark - AR, Cottage: Red Colour, Size: 335mm x 984mm, Algea Resistance, UL Class Fire Resistance, 110 km/hr Wind Resistance, Shingles (Roof) nailed upon the plywood surface (19mm Waterproof Plywood) including all necessary fittings at Park of Hon'ble Minister's Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Children Playing Equipment- Sea Saw Double Planks KE- 201 with all necessary fittings at Park of Hon'ble Minister's Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Children Playing Equipment- Arch Swing Double KE- 408 with all necessary fittings at Park of Hon'ble Minister's Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Children Playing Equipment- Multiplay Station Fantasy KE- 802 with all necessary fittings at Park of Hon'ble Minister's Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Children Playing Equipment- Delux Slide 5ft KE- 304 with all necessary fittings at Park of Hon'ble Minister's Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Children Playing Equipment- Spring Rides KE- 511, KE- 512 with all necessary fittings at Park of Hon'ble Minister's Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Children Playing Equipment- Merry Go Round KE- 602 with all necessary fittings at Park of Hon'ble Minister's Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Outdoor Cast Iron Garden Benche- KE 14022 (3 Seater Bench) of side made of cast iron and seating area made of MS hollow section (size 50x25) along with black enamel paint (2 coats) and primer (2 coats) with all necessary fittings at Park of Hon'ble Minister's Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Outdoor Garden Sofa (Single Seater Sofa) with all necessary fittings at Park of Hon'ble Ministers Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Outdoor Garden Sofa (2 Seater Sofa) with all necessary fittings at Park of Hon'ble Ministers Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Outdoor Garden Sofa Centre Table (Round Centre Table) with all necessary fittings at Park of Hon'ble Ministers Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Outdoor Garden Table with all necessary fittings at Park of Hon'ble Ministers Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Outdoor Garden Chair with all necessary fittings at Park of Hon'ble Ministers Colony at Dispur in all complete as approved and specified by the Department.

Supply and Installation of Outdoor Garden Table with all necessary fittings at Park of Hon'ble Ministers Colony at Dispur in all complete as approved and specified by the Department.

Supplying and planting of Aesthetic Plant-Plumeria Alba (Size: 1800 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Chandni Variegated Hedge (Size: 300 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Champiam Palm (Size: 1200 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Red Palm (Size: 1350 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Fox Tail Palm (Size: 2400 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Bougainvillea Variegated (Size: 750 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Punda Ficus (Size: 900 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Bismarckia Palm (Size: 1500 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Black Ficus (Size: 450 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Syzgium Plant (Size: 300 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Exora Mini (Size: 200 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-London Pine (Size: 1350 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Cycus Palm (Size: 45 leaves, 900 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Heliconia Red & Yellow (Size: 600 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Croton (Size: 300 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-GulMohar (Size: 1800 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Kanchan (Size: 1800 mm) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and planting of Aesthetic Plant-Golden Hedge (Size: Small Pkt) on landscap ground including the preparation of the pit, removing unwanted debrises, filling the pit with manure and fertilizers as per specification and necessary maintenance for a period of 6 months from the date of planting complete as specified and directed.

Supplying and filling in Brahmaputra River Fertile Soil (including royalty) at Low lying ground including ramming, dressing and watering of the earth in layers complete at Park of Hon'ble Minister's Colony at Dispur as approved and specified by the Department.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch

3 pin 5/6 A socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required 6 Module (200mmX75mm)

12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. 6 Module

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required 125 A, 16 KA,TPMCCB

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, clusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Excavation for cable trenches in soft soil, depth upto 1.2 m including dressing of sides lift upto 1.5 m, including getting out the excavated soil, refilling with sand and or good soil after laying of cable/ pipe etc in layers of 20 cm, ramming, watering and disposal of surplus excavated soil as directed, within a lead of 50 metres

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required Upto 35 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 32 mm dia nominal bore

25 mm dia nominal bore

80 mm dia nominal bore

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal/ coke and salt ) as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying installation testing and commissioning of Chandeler eleganza Ceiling fan as required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Orient/ Crompton/ Havells

Supplying installation testing and commissioning of LED recessed mounted round downlight with die cast aluminium housing light as required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Phillips/Jaquar make LESP01RO15XN 15W

Supplying installation testing and commissioning of Dia cast aluminium housing transparent glass diffuser IP54 (Up - Down light) as required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Phillips/Jaquar make CARINA LWWL03X203XW 2X3W

Supplying installation testing and commissioning of Dia cast aluminium housing ,trasparent tempered anti glare diffuser with IP54 as required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Phillips/Jaquar make NASH LFLT01S105XW 10X.05 W

Supplying installation testing and commissioning of Dia cast aluminiun housing ,transparent tempered glass IP65 required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Phillips/Jaquar make SPARKLZ LSPK04R112XW 1X12W

Supplying installation testing and commissioning of BOLLARD ITEM NO.ZL1922/5A required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Phillips/Jaquar make ITEM NO.ZL1922/5A

Supplying installation testing and commissioning of POST OF LENTERN LIGHT (ITEM NO .ZL1991/8) required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Phillips/Jaquar make ITEM NO.ZL1922/5A

Supplying installation testing and commissioning of WALL FAN ELECTRIC BLUE required 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Phillips/Jaquar make WALL FAN ELECTRIC BLUE 400 MM

Supplying installation testing and commissioning of Tempo meni flood lighting luminaire with PDC housing and unique flood optics (NB) to ensure unifrom distribution equired 1.5 sq mm copper multstrand wire connection an as specified and directed by the Deptt.Phillips/Jaquar make BVP180 LED50 CW PC WB 50W 120-270 PSU

SITC of supplying U.G. Cable complete with cable lug etc all accessories of following capacity as approved and directed by the Department (havells/ RR Kable/Phinolax etc) 3 core XLPE Insulated U.G. Cable Aluminium size 6 sq mm

Supplying including fitting fixing of following A.C. Wall fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department.

Supplying, installation, testing and Commission of Foam Fountain at Central Park submersible pump make aquasub 01 No,Led fountain lights Ip-65 Make CDI-10 Nos, Foam Nozzles made :- Brass with chrome polish 10 Nos.Submesible cabling round 4 core copper wire, requiremed plambing required electrical works electrical PVC conduits main distribution section made GI brass ball Joint :10 Nos, Enamel paint, Labour with all fittings etc as specified and directed by the Department.

SITC of supplying U.G. Cable complete with cable lug etc all accessories of following capacity as approved and directed by the Department (havells/ RR Kable/Phinolax etc) 3 core XLPE Insulated U.G. Cable Aluminium size 25 sq mm

SITC of supplying & installation of HGS smarty series Astronomica panel bord 12KW complete connection with cable lug etc all accessories of following capacity as approved and directed by the Department (havells/L&T etc)

SITC of supplying U.G. Cable complete with cable lug etc all accessories of following capacity as approved and directed by the Department (havells/ RR Kable/Phinolax etc) 4 core XLPE Insulated U.G. Cable Aluminium size 16 sq mm .

SITC of supplying U.G. Cable complete with cable lug etc all accessories of following capacity as approved and directed by the Department (havells/ RR Kable/Phinolax etc) 3.5 core XLPE Insulated U.G. Cable Aluminium size 70 sq mm .

Puberun Real Estate Pvt. Ltd.