CERTAIN B/R REPAIRS TO MES INSTALLATION IN TECH AREA UNDER GE AIR FORCE STATION PATHANKOT

Amount

Taking down chowkhats or frame of any discreption with shutter n exc 1.50 sqm each complete all as specified and directed by the Engineer-in-charge.

Taking down chowkhats or frame with shutter of any discreption exc 1.50 sqm but n exc 4 sqm each complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing pressed steel frames door 125 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer, including incl fixing of holdfast complete.NOTE:- During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing pressed steel frames door 105 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer, including incl fixing of holdfast complete.NOTE:- During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement complete all as specified and directed by the Engineer-in-charge.

Supply & Fixing for 30mm flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides particle board core all as specified and directed by Engr-in-charge. NOTE :- All screws shall be self tapping chrome plated complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair 35mm thick 2nd class Hard wood glazed and skelton shutters open rebated and prepared to receive glass gauze (Without sash bar ) etc as specified in SSR Pt- I Sec -8 clause 8.20 (a) complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Galvanised stainless steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by the Engineer-in-charge.

Material and Labour for preparing of new wooden surfaces of any description over 10cm in width or girth and applying two coat of synthetic enamel paint,over one coat of pink primer complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification and drawing complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 150mm aluminium handles cast type (anodised), fixed with steel chromium plated bright screws complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 300mm aluminium anodised sliding door bolt with hasp staple (Bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding door bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing aluminium anodised barrel tower bolt of extruded section of size 150 mm complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor including rubber bush compete (overall length of cover plate 150mm) complete all as specified and directed by the Engineer-in-Charge.

Supply and Fixing 100 mm stainless steel but hinges, medium weight quality (ISI Marked), fixed with steel chromium plated bright screws complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing for factory made Steel window/ Ventilator 1.25mm thick box type(primer coated)ERW hollow P section of size 60mmx25mm including grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two open able leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick including taking down with existing one four Nos for each window including following fitting welded to frame shutter : (a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) MS Tower bolt 150mm long-02No per leaf . (d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, (g) Including two coats of synthetic enamel paint complete. (h) Stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm &fixed with aluminium wire staples. (j) Glass pane 3mm thick fixed with MS pin and oil putty. NOTE: During Fixing of window, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.cutting holes and good dismantled portion in PCC(1:2:4) type B1 complete all as specified and directed by the Engineer-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing 3.00 mm thick glass sheet, ordinary quality and glazing with oil putty in square exc 0.5 sq.m ineach pane complete all as specified and directed by the Engineer-in-charge.

Cutting holes in brick walls built in cement mortar or cement lime mortar exc one brick but not exc two bricks for inserting hold fasts/ iron posts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 complete all as specified and directed by the Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description and in any position complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing mild roof structural steel angles/rectangular hollow section/steel tubular roof trusses (framed), purlines and fastening including distance pieces etc complete all as specified and directed by the Engineer-in-charge.

Dismantling AC corrugated or semi corrugated sheets in wall cladding complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engineer-in-charge.

Excavating in post holes each n.exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25 cm watering and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed by the Engineer-in-charge.

Material and Labour for cement conc 1:3:6 type C-2 (40 mm graded aggregate) as in post/strut foundation complete all as specified and directed by the Engineer-in-charge.

Material and Labour for demolition of existing hardstanding/ paver blocks of any depth with mechanical means and disposing of watse out of MoD land complete all as specified and dircted by Engineer-in-Charge.

Material and Labour for 100mm thick Hardcore (broken stones or boulders) of guage not exc 63mm deposited spread & leveled in layers watered & rammed to a true surface complete all as specified and dircted by Engineer-in-Charge.

Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed by the Engineer-in-charge.

Material and Labour for 100mm thick PCC (1:2:4) type B-2 using 40 mm graded stone aggregate as in floor finising fineshed even and smooth without using extra cement complete all as specified and dircted by Engineer-in-Charge.

Preparing new steel surfaces of any description exc 10cm width or grith and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed by the Engineer-in-charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing servicable tiles to store and rubnbish of the permises complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Rendering 10 mm thick on wall and the like to receive tile in cement mortar (1:4), complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Glazed ceramic coloured tiles, of size350x 250x 7mm/ 450X 350X 7mm thick,as in skirting, dado set and jointed with neat cement slurry including pointing in white cement with pigment to match the shade of tiles complete all as specified and directed by the Engineer-in-charge.

Material and Labour for Screed bed or bedding layer of mortar 15 mm thick average thickness for laying floor finishes in cement mortar (1:4) complete all as specified and directed by the Engineer-in-charge.

Material and Labour for 25 mm thick, PCC (1:2:4) type B-O using 12.5 mm graded stone aggregates as in flooring as leveling course complete all as specified and directed by the Engineer-in-charge.

Non skid ceramic coloured tiles, 7 to 8 mm thick (square or rectangular) area of each tile exe 0.11 Sqm but n.exe 0.18 Sqm, laid in floors set and jointed with neat cement slurry including pointing in white cement with pigment to match the shade of tiles, complete all as specified and directed by the Engineer-in-charge. (Make : Kajaria, Somany, Johnson).

Material and Labour for light shade vitrified tiles flooring 9-10mm thick (square/rectangular), polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in net slurry and pointed in white or coloured cement to match existing shed complete all as specified and directed by the Engineer-in-charge.

Material and Labour for 100 mm thick, PCC (1:4:8) type D-2 using 40 mm graded stone aggregates as in sub base complete all as specified and directed by Engr-in-Charge.

Material and Labour for 80 mm thick machine pressed precast concrete interlocking paver block any shape and size & Colour M-50 grade with grey cement and pigment confirming to IS 15658-2006 incl 25mm sand cushioning complete all as specified and directed by the Engineer-in-charge.

Supply and fixing 15 mm tubes medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floor including taking down old u/s pipes complete all as specified and directed by the Engineer-in-charge.

Supply and fixing 20 mm tubes medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid in floor including taking down old u/s pipes complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs 500 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) white colour three layers hoisted and fixed in position including taking down U/S tanks and GI tank nipple etc. complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs vitreous china wash down water closet pan (pedestal pattern) white, with 'P' or 'S' trap (excluding flushing cistern and flush pipe) including connection to drain and to flushing pipe complete incl making good to floor to match with adjoining surface and taking out existing WC complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs PVC valve less syphon action type low level flushing cistern 8-10 liters capacity with intel, ball valve, float valve push button type handle including telescopic flush pipe 32 mm dia complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs vitreous chinaware wash hand basin white, flat back of size 550x400 mm excluding tap but including brackets fixing to wall and two Nos 10mm dia 100mm long nut and bolt over brackets including 32mm bore PVC waste pipe and CP waste coupling complete and fixed in repair complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs viterous China urinal, bowl type back or corner wall type of size 465x355x265 complete with waste fittings including urinal spreader providing and fixing complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs 15mm dia Bib Taps, CP fancy type with crutch or butter fly handle screwed down pipe or for screwed iron pipe ccomplete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs 15mm dia CP stop cock concealed type cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs 15mm dia CP angle cock cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for union complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs pillar taps, 15mm bore cast copper alloy with capstern head, chromium plated screwed down high pressure with or without lettered hot or cold complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repairs brass chromium plated towel rail 20 mm outer dia `D’ type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and directed by the Engineer-in-charge.

Supply and fixing in repairs 15mm dia PVC connection with brass check nut of length 450mm complete all as specified and directed by the Engineer-in-charge.

Material and Labour for 3mm thick PVC sheets laminated plain coloured, marbled , mosaic or mottled finish, laid with approved rubber based adhesive as in floors complete all as specified & directed by Engineer-in- charge.

Removing old tar felt, all loose dirt,old roof tiles,cleaning the concrete surface including removal & cleaning of vegetation, fungus,mass small trees etc from the roof top with wire brush, removing the strips of lightening conductor including refixing the same after repair work and applying neat cement slurry @ 1.5Kg/Sqm complete all as specified and directed by Engineer-in-Charge.

Material and labour for 15mm thick cement plaster in CM 1:4 over concrete surface on top of roof finished even and smooth without using extra cement mixed with water proofing compound pidi proof LW @ 200ml per 50Kg cement as per manufacturers instructions complete all as specified and directed by Engineer-in-Charge (WPC shall be measured and paid separately).

Supply only liquid water proofing compound pidilite LW complete all as specified and directed by the Engineer-in-charge.

Supply and fixing for fibre reinforced, UV resistant elastomeric liquid applied waterproofing and Heat reflective coating coating with PU Hybrid polymers & acrylic fibres, SmartCare DampProof Ultra or approved equivalent. The coating shall resist 10 bars of water pressure as per DIN 1048 standards, with elongation of 350% as per ASTM D412 & crack bridging of upto 2.5mm conforming to ASNZ standard, The coating shall reduce the surface temperature of 10 degrees, etc., complete all as specified and directed by the Engineer-in-charge as per Manufacturere specifications.

Supply and Fixing in repair positioning suspended false ceiling using E Grid suspended ceiling system of grid size 600mm x 600mm with GI frame work of main runner 38mmx24mm sheet thickness 0.4mm cross 28mm x 24mm sheet thickness 0.3mm and wall angle 24mmx 24mmx 3mm using 4mm thick high pressure steam cured classic variant E Board designer pattern fiber cement E board to be placed in the grid suspended by 4mm GI wire hangers from the purlins of the roof with butterfly clips incl preparation of surfaces and applying two coats of synthetic enamel paint over one coat of primer, complete all as specified and directed by the Engineer-in-charge.

Demolition of brick work , built in cement mortar or cement lime mortar including all quions, arches, pillars, etc including demolition of precast rcc articles and disposal of debris out of MoD land complete all as specified and directed by the Engineer-in-charge.

Material and Labour Brickwork with burnt clay old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed by the Engineer-in-charge.

All as per item No 02 above but except bricks complete all as specified and directed by the Engineer-in-charge. NOTE: Old burnt clay bricks retrieved from demolition shall be used.

Taking down cement plaster of any description any layer and thickness on brick or stone walls and ceiling including raking out joints, hacking for keys, scubbing down with water etc and complete all as specified and directed by the Engineer-in-charge.

Material and Labour rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed by the Engineer-in-charge.

Material and Labour for rendering cement plaster 5mm thick in CM (1:3) on fair faces of concrete surfaces, finished even and smooth wihout using extra cement on ceilings complete all as specified and directed by the Engineer-in-charge.

Material and Labour rendering 15mm thick on other than fair faces of brick work or concrete surfaces in CM (1:4) finished even and smooth without using extra cement complete all as specified and directed by the Engineer-in-charge.

Material and Labour Washed stone grit plaster on exterior walls in two layers, under ayer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified and directed by the Engineer-in-charge. (Payment for providing grooves shall be made separately).

Material and Labour for preparing of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by the Engineer-in-charge

Material and Labour for preparing of newly plastered surfaces of ceilingss and applying three coats of white wash complete all as specified and directed by the Engineer-in-charge

Material and Labour for finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) in camouflage pattern (four) or more shades as directed by Engr-in-Charge incl necessary scaffolding and other safety arrangement to work at any height at site if required complete all as specified and directed by the Engineer-in-charge.

Bringing extra earth if required from inside ministry of defence (MOD) land at a distance exc 250 m and not exc 6.00 Km for filling and raising (or lowering) earth, upto 6 m height spreading in layer, watering, compacting and finishing to required gradient/ shape and deposited where directed complete all as specified & directed by Engineer-in- charge

Cutting holes exc. half brick but n exc one brick wall build in cement mortar of size 150mm X 150 mm X 345 mm for inserting (PVC Pipe and bend with PVC vent cawl) 110 mm and filling brick bats on earth side and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 and finished the surfaces to matching with existing surfaces including dismentling old PVC pipe in weep holecomplete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair 200x200mm weep hole cover made out of 20x2mm glavnised plain sheet frame with GI neeting 15mm spacinig, thickness of wire 1mm including all necessary drilling , bolting or riveting and fixed on any type of wall with screws or nut bolt and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 and finished the surfaces to matching with existing surfaces complete including dismentling old weep hole cover complete including providing filter media material such as 40mm graded crushed stone aggregate in weep hole complete all as specified and directed by the Engineer-in-charge.

Materal and Labour for 18 to 20 mm thick PVC prelaminated solid board with one side decorative choice laminate and other side balancing white including 3mm thick lipping and equal to thickness of board as in kitchen cabinet, cupboard etc fixed with screws to steel/timber frame work etc complete all as specified and directed by the Engineer-in-charge.

Supply and fixing for Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed by the Engineer-in-charge.

Supply and fixing for 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing Continuous (piano) hinges 30mm Width of flaps (when open) ,mild steel, bright finish or electrogalvanised complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing of anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing of anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as door stopper (1 No.). hinges type B-21 125mm long (3 Nos.) suitable handle (2 Nos.) for each shutter complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing of anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1 No.) for each shutter complete all as specified and directed by the Engineer-in-charge.

Supply and Fixing in repair of sheet glass 4.8 mm thick, ordinary quality and glazing in aluminium shutter in square exc 0.5 sq. m in each panecomplete all as specified and directed by the Engineer-in-charge.

Material and Labour for repair or tightening of loose Aluminium doors/windows, changing old damaged rubber beadings and cleaning/repairing of floor spring/hydraulic door closer etc, complete all as per specified and directed by Engineer-in-Charge.

Supply and Fixing for ACP sheet 4mm thick in aluminium frame including necessary fittings, complete all as per specified and directed by Engineer-in-Charge.

Taking down metal rolling shutters of any size self closed or gear type and refixing in the same opening after carrying out necessary repair as :- Oiling and greasing with lubricant to guide rail gear box etc of rolling shutter if any size including straightening of any strip, hood cover, guide rail and tightening of rolling spring complete, repair to old bevel gear box for any size of opening including replacement of old tension spring with new tension spring in the same position, complete all as per specified and directed by Engineer-in-Charge.

Demolition of existing roof treatment of any description such as worm out tarfelt, mortar of any description & any thickness, shrubs/roots ,vegetation, tree, terracing pcc/brick tiles, concrete bedding etc as directed and Cleaning of all foreign material debris etc by brushing and dusting, washing down with water etc ,surface shall be leveled with a layer of 20 mm thick screed bed in CM 1:4 including mixed with water proofing admixture as per manufacturer's instructions and applying roof treatment with 03mm thick APP modified membrane with non-woven polyster reinforcement(center core) with thermal insulation with plane finish on upper side of weight not less than 3.5 kg/sqm , laid by torch application method with overlap 100 mm on length side and 100 mm on the width side as per manufacturer's instructions over one coat of approved cold applied bituminous oil based primer (IS-3384) @0.30 litre/sqm complete all as specified and directed by the Engineer-in-charge.

INDERJIT SINGH (BID ID -3062472)

Surya & Gautam Builders (BID ID -3061702)

M/S G P MARWAHA (BID ID -3061754)

pardeep singh marwaha (BID ID -3061992)

M/S SINGH AND ASSOCIATES (BID ID -3062127)

new hi tech engineers and contractors (BID ID -3062063)