SPL REPAIR TO ROOF TREATMENT IN CIVILIAN MD ACCN 03 X BLOCKS AND M-15 (SINGLE QTR) AT VRC AND SPL REPAIR TO BLDG NO.P-26 (POLYCLIINC) OF IHQ OF MoD (ARMY) CAMP UNDER AGE B/R-I AND AGE E/M OF GE (SOUTH) DELHI CANTT-10

Amount

Dismantling of brick tiles (laid flat or on edge) on roof surface laid bedded and pointed in any mortar complete all as specified and directed by Engr-in-Charge.

Demolition of mud in roof, any thickness, including plastering and leeping upto two storey bldg incl necessary scaffolding arrangement complete all as specified and directed(whether full thickness removed or only a part there of) and removing from cantonment area or complete all as specified and directed by Engr-in-Charge.

M&L for brushing neat cement slurry with 3.00 Kg of cement per Sqm on existing surfaces complete all as specified and directed by Engr-in-Charge.

M&L 50 mm thick (average thickness) plain cement concrete 1:2:4 type B-0 using (12.5 mm graded aggregate), as in roof, padding to maintain the uniform slope complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick (average) plaster on concrete surfaces in CM (1:4) on roof, mixed with water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. Note : Water proofing compound shall be measured and paid seperately.

M&L, Priming roof surfaces and applying water proofing treatment over roofs comprising of the following complete all as specified & as directed:-

(a) Applying oil bound bituminous primer at the rate of 0.30 Ltrs/Sqm as per IS 3384-1986 on prepared surfaces. Surface shall be kept free till the moment, the primer is impregnated and the solvent oil in primer is evaporated.

(b) Applying one coat of hot straight run bitumen @ 1.20 Kg/Sqm of grade 30/40 confirming to IS-73 (Grade S-35).

(c) Laying 3mm thick APP polymeric water proofing membrane of weight not less than 3.6 kg/sqm, black finish reinforced with non woven polyster matt, (weight not less than 160 gm/Sqm) with a thermo fusible finish, torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer's instruction including preparation of surface.

make of APP: "Moply FP" manufactured by STP Texsa Ltd or Hyper Plas (Polyester) manufactured by M/S IWL Ltd or "Shaliplas"ter) manufactured by M/S Capital Steels and Chemical Pvt Ltd or Makpolyplast manufactured by M/S M K Patro as approved by GE.

Note :- The water proofing treatment shall be got carried out by the manufacturer or their authorised applicators. The contractor shall give 10 years guarantee for effectiveness of water proofing treatment, 2.5% of work done amount of this item shall be retained from contractors payment for a period of 10 years reckoned from date of physical completion of this work, or in lieu contractor may deposit bank FDR for the said amount for 10 years which shall be released by GE on expiry of satisfactory completion of 10 years period.

All as per item No.6 above, but on vertical surfaces.

M&L for cement concrete tiles 25cmx25cmx22mm thick laid over and including 20mm thick screed in cement mortar 1:6 and jointed grouted and pointed in CM 1:3. complete all as specified and directed by Engr-in-Charge.

M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete all as specified and directed by Engr-in-Charge.

Supply only water proofing compound.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge.

M&L for 15 mm thick rendering with Readymix plaster (as per manufacturer's instructions) on fair faces of brick work or concrete surfaces finished even and smooth surface without using extra cement on wall and ceiling of up to four storied bldg complete all as specified and directed by Engr-in-Charge.

M&L for 5 mm thick rendering with Readymix plaster (as per manufacturer's instructions) on fair faces of brick work or concrete surfaces finished even and smooth surface without using extra cement on wall and ceiling of up to four storied bldg complete all as specified and directed by Engr-in-Charge. Notes for Srl item Nos. 12 & 13 :- 1. Make of readymix plaster shall be Birla Aerocon/Ultratech Readiplast/ACC Accoplast/Fosroc Chemical (India) Pvt Ltd Renderoc and as approved by GE. 2. The readymix plaster shall be procured directly from the manufacturer or from their authorised dealer. 3 The contractor shall produce original purchase voucher alongwith test certificate of readymix plaster while claiming RAR/ Final Bill. 4. The Engr-in-Charge shall verify the genuineness of these purchase vouchers before endorcing.

M&L for preparation of new plastered wall surfaces and applying two coats of cement base paint, white or tinted (colour and shade as per new colour scheme approved by GE) over a coat of primer of same make including scaffolding for four storey building complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old decorated wall surfaces by complete removal of existing treatment and applying two coats of cement base paint, white or tinted (colour and shade as per new colour scheme approved by GE) over a coat of primer of same make including scaffolding for four storey building complete all as specified and directed by Engr-in-Charge.

M&L for chipping of spalled and loose concrete and cleaning rust from re-inforcement by sand blasting scrubbing down conrete sufrace with wire brushes cleaning with water allowed to dry and applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bonding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited all as specified and applying two layess of guniting over steel welded mesh 2mm dia of wire and aperture 75mm,total thickness of gunite n.exc 25mm thick (average thirteen) auth cement mortar 1: 2 using OPC 53 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufacturers instructions and finally applying cement plaster over gunite surface of required thickness to give even uniform and smooth finish conforming to proper gerometrics in cement mortar (1:3) to match with the existing surface as in sides and soffits etc of slabs, chajjas, fins, facias, parapets , columns and beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 4 storey bldgs complete all as specified and directed by Engr-in-Charge. Note : Steel welded mesh is to be tightening/welding with the existing re-inforcement. The cost of welded mesh is deemed to be included in the unit rate quoted.

Taking down rain water pipe (any size) or pattern incl all fittings, head shoes, bends swan necks etc incl cleaning or re-fixing or removal to store(measured overall as fixed along the centre line over fittings and accessories complete all as specified and directed by Engr-in-Charge.

S&F for PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, of 110 mm dia complete all as specified and directed by Engr-in-Charge.

S&F for PVC (SWR) bends any radius 110mm dia bore complete all as specified and directed by Engr-in-Charge.

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres complete all as specified and directed by Engr-in-Charge.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves, high pressure, with polythene float and fly- nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

Disconnecting existing tanks, exc 250 ltr and n exc 500 ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting reconnecting and re-fixing after repair cleaning etc in same position complete all as specified and directed by Engr-in-Charge. Note :- The rate quoted by the tenderer are also deemed to be included necessary repair work of water tank to make fully functional as per site requirment.

Taking up or down steel tubing and connections including cleaning for re-fixing or removal to store, 15 mm bore of pipe complete all as specified and directed by Engr-in-Charge.

All as per Srl item No.23 above but 20 mm bore of pipe.

All as per Srl item No.23 above but 32 mm bore of pipe.

M&L tubes, medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid floors, 15 mm bore of pipe complete all as specified and directed by Engr-in-Charge.

All as per item No.26 above but 20 mm bore of pipe

All as per item No.26 above but 32 mm bore of pipe

Cutting of trees including cutting of trunk n.exc 30cm girth and branches and digging out roots from floor or roofs and walls of up to four storied bldg and making good the dismantled portion in cement mortar 1:3 to match the existing surfaces complete all as specified and directed by Engr-in-Charge.

Cutting chases or making holes, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed by Engr-in-Charge.

Taking down door/window chowkhat or frame with shutters (without taking off shutters from the frame n.exc 1.5 sqm each complete all as specified and directed by Engr-in-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be coloured with heat mould plain coloured PVC'C channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock and botton rail either side and as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engr-in-Charge.

S&F solid PVC doors & frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification & drg in SSR 2009 Part II complete all as specified and directed by Engr-in-Charge.

S&F 100 mm size butt hinges medium weight stainless steel complete all as specified and directed by Engr-in-Charge.

S&F 150mm long stain less steel, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-Charge.

S&F stainless steel handles of 100 mm size complete all as specified and directed by Engr-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing removing serviceable to store and rabbish off the premises complete all as specified and directed by Engr-in-Charge.

M&L for non Skid ceramic tiles 7 to 8mm thick coloured & joint free (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors over and including 15 mm thick screed bed or bedding layers in cm 1:6 etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for glazed coloured, joint free ceramic tiles in vertical surface of size 450X300X7mm thick over and including 10 mm thick rendering set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-Charge.

Rounding to edges of stone slabs on edge, such as in steps cooking platform and other similar situations complete all as specified and directed by Engr-in-Charge.

S&F in repairs wash hand basin vitreous China flat back 550x450mm size white, including PVC waste coupling 32mm size, pair of brackets of mild steel 35 x 35 x 6mm size including complete all as specified and directed by Engr-in-Charge.

S&F in repairs vitreous china squatting pan (Orissa pattern) long pan fixed size 580x440mm white with integral footrest with `P' or `S' trap complete all as specified and directed by Engr-in-Charge. (excluding flushing cistern and flush pipe).

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern) , white fixed in repair,including sheet cover of closed pattern with flat bottom and mild steel chromium plated or aluminiumised hinging device complete all as specified and directed by Engr-in-Charge.

S&F in repairs 15 mm bore, Wash hand basin Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC connection for 15 mm bore pipe,450mm long complete all as specified and directed by Engr-in-Charge.

S&F in repairs 32/40 mm bore and 75 long PVC Waste pipe suitable for WHB/Sink complete all as specified and directed by Engr-in-Charge.

S&F in repairs Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC valveless , syphonic action type flushing cistern 10 ltrs capacity , low level , white, with inlet ball valves, float and handle including brackets and pvc flush pipe 32 mm dia for low level complete all as specified and directed by Engr-in-Charge.

S&F in repairs 15mm bore chromium plated bib tap long body with flange fixed in 15mm bore of pipe, cast copper alloy with crutch of butterfly handle, screwed in iron pipe complete all as specified and directed by Engr-in-Charge.

S&F in repairs 15 mm bore angle stop valves (fancy type), cast copper alloy , chromium palted, screwed down high pressure witg crutch and butter fly handles , screwed with iron pipes or for union complete all as specified and directed by Engr-in-Charge.

S&F in repairs Stop valves 15 mm bore fancy type, CP with long shank & cup (conncelaed type), cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed by Engr-in-Charge.

S&F in repairs grating dome 125 mm dia with waste hole of PTMT complete all as specified and directed by Engr-in-Charge. (Minimum weight 40 gms)

M&L for preparation of newly plastered surfaces on wall/ceiling of chajjas etc and filled with wall care putty to achieve even and smooth surface and then applying two coat of 100% anti fungal acrylic emulsion exterior grade whether proof paint over a coat of weather resistant acrylic primer complete all as specified and directed by Engr-in-Charge. Note: The surface shall be got approved by the GE before application of first coat of paint and then before subsequent coat.

M&L for complete removal of existing treatment of old treted surface of wall by sand paper and filled with wall care putty to achieve even and smooth surface and then applying two coat of 100% anti fungal acrylic emulsion exterior grade whether proof paint over a coat of weather resistant acrylic primer complete all as specified and directed by Engr-in-Charge. Note: The surface shall be got approved by the GE before application of first coat of paint and then before subsequent coat .

M&L for complete removal of existing treatment of old treated surfaces and applying two coats of distemper oil emulsion over water based primer with 2 mm thick JK wall putty on wall surfaces complete all as specified and directed by Engr-in-Charge.

M&L for of new plastered surface wall / ceiling and applying two coats of distemper oil emulsion over water based primer with 2 mm thick JK wall putty on wall surfaces complete all as specified and directed by Engr-in-Charge.

Taking down 100 mm bore cast iron pipes including fittings by burning out lead joints etc to facilitate dismantling old serviceable fittings/pipes laid in trenches,floors or fixed to walls all as directed including earth work, demolition of PCC/Brick work complete all as specified and directed by Engr-in-Charge.

All as per Srl item No.59 above but 75 mm bore of pipe.

S&F 100 mm bore cast iron sand soil waste or vent pipes (ISI Marked), in any length with or without ears with joints in cement mortar (1:3), laid in trenches, floors or fixed to walls all as directed including making good to match with existing surfaces complete all as specified, for the following sizes of pipes.

All as per Srl item No.61 above but 75 mm bore of pipe.

S&F in repairs 100 mm bore cast iron branch pieces (ISI Marked), single (equal or unequal) ordinary of inverted spigot or socket type complete all as specified,for the following sizes of pipes.

All as per srl item No.63 above but 75 mm bore of pipe.

S&F in repairs 100 mm bore cast iron bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified, for the following sizes of pipes.

All as per Srl item No.65 above but 75 mm bore of pipe.

M&L in repairs 75 mm out let dia CI floor trap incl jointing to waste pipe in run lead complete all as specified and directed by Engr-in-Charge.

M&L in repairs 100 mm out let dia CI floor trap incl jointing to waste pipe in run lead complete all as specified and directed by Engr-in-Charge.

Demolition of brick work built in CM incl quoins, arches, pillers etc complete all as specified and directed by Engr-in-Charge.

M&L brick work in cement mortar (1:6) using sub class 'B' bricks, straight or curved on plan exc 6 mtr mean radius complete all as specified and directed by Engr-in-Charge.

Cutting grooves in brick wall, 75mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engr-in-Charge.

Demolition of lime concrete or cement concrete including tilling etc in ground floors and pavings not exc 15cm thick (below or above ground level) complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggt) as in sub base of floor/plinth proctions etc finished surface fair & even complete all as specified and directed by Engr-in-Charge.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade 'A' complete all as specified and directed by Engr-in-Charge.

S&F gun globe or gate valve for 15 mm bore pipe with iron wheel had screwed both ends for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F gun globe or gate valve for 20 mm bore pipe with iron wheel had screwed both ends for iron pipe complete all as specified and directed by Engr-in-Charge.

S&F galvanised iron tank nipple 15mm bore suitable for HDPE water tank complete all as specified and directed by Engr-in-Charge.

M&L for brick work using old size bricks of class designation 10, built in cement mortar (1:4), straight or curved on plan, exc 6 metre mean radius complete all as specified and directed by Engr-in-Charge.

Excavation in trenches in soft/loose soil, not exc 1.5m wide & n exc 1.5m in depth as in foundation , mainholes etc.n exc 10 sqm on plan and n exc 1.5 m in depth and getting out complete all as specified and directed by Engr-in-Charge.

Demolition and breaking up 150 mm dia drain pipes (salt glazed stoneware/ACC/RCC), set in cement mortar, including removal of waste material upto 500 metre distance at the place notified by the Engineer-in Charge.

M&L for salt glazed stoneware drain pipes 150 mm bore, laid in trenches and jointed in cement mortar (1:4) and tested complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete (1:3:6) type D-2 (using 40mm graded stone aggregate) as in bed to drain pipes of 150 mm bore of SGSW pipe including packing under and haunching against sides of pipes after they are laid and tested, complete all as specified and directed by Engr-in-Charge.

Returning, filling in including, spreading, levelling, watering and well ramming in layers n.exc 25cm thick, in soft/loose soil complete all as specified and directed by Engr-in-Charge.

Removal of excavated surplus soil to a distance not exc 50 metre where directed by Engineer-in-Charge at a level not exc 1.5m above or below the starting point complete all as specified and directed by Engr-in-Charge.

S&F in repairs SFRC manhole cover size (1200 X 600 x 70) mm thick with frame set in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Notes: - (i) Make of SFRC Manhole/drain cover and frame : (a) M/s PS Concrete. (b) M/s KK Manhole.(c) Or equivalent as approved by GE” (ii) Contractor will provide manufactuerer test certificate of SFRC cover & frame

M&L in repair, salt glazed stone ware gully trap, square or round mouthed,150mm x 150 mm size, shape as required,including dismantling and taking out of old GT and jointing with old connection and pipes complete all as specified and directed by the Engineer-in-Charge.

Extra for forming fair furnished drain or channels 30 cm inner girth in cement concrete using cement including forming moulds,mitred/stopped ends etc complete all as specified and directed by Engr-in-Charge.

M&L for PCC(1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundation and mass concrete complete all as specified and directed by Engr-in-Charge.

Taking down carefully the old U/S Aluminium point wiring (light, fan, socket or power) complete fitting such as switches, ceiling roses, pendants, sockets, regulators, etc and making good disturbed surfaces of walls including necessary touch up with the adjoining surface of disturbed area ie with OBD/colour wash/white wash as the existing finish complete all as specified and directed by Engr-in-Charge.

M&L for point wiring complete, stranded copper conductor 1.5 Sqmm nominal area PVC insulated FRLS 1100 volts grade electrical cable in but with through existing concealed PVC conduit medium grade and sunk in pressed steel terminal boxes of required size with top cover 3 mm thick plastic/laminated sheet of required color with screwed and cup washer complete with all accessories including 1.5 Sqmm standard copper conductor PVC unsheathed cable earth and connected to earth dolly complete all as specified and directed by Engr-in-Charge. Note :- In existing conduit wiring new conduit will be added if there is a blockage/damage to the existing conduit including bends/elbows/tees/junction boxes with the adjoining surface of disturbed area with OBD/colour wash/white wash complete.

All as per item No.91 but One light /fan/Bell point/security light controlled by one way switch.

All as per item No.91 but One 3 pin socket outlet 5 amps point independent board with cable 1.5 Sqmm for main current and 1.5 sqmm as earth wire as power point.

All as per item No.91 but One 3 pin socket outlet, 15 amps on independent board with cable 2.5 Sqmm for main current and 2.5 sqmm as earth wire as power point.

S&F switch piano flush type 5/6 Amp one way single pole complete all as specified and directed by Engr-in-Charge.

S&F socket outlet 5 pin 5/6 Amp two in one complete all as specified and directed by Engr-in-Charge.

S&F switch piano flush type 15 Amp complete all as specified and directed by Engr-in-Charge.

S&F socket outlet 2 in 1, 5 pin 15/5 Amp complete all as specified and directed by Engr-in-Charge.

S&F of ceiling rose surfaces bakelite minimum size 65x50mm with two/ three terminals complete all as specified and directed by Engr-in-Charge.

S&F in repairs of plastic body heavy duty exhaust fan 250 mm sweep, 230 Volts with louver and copper wound including necessary electric connection with appropriate size of PVC copper wire from ceiling rose/switch board to exhaust fan including fixing of nut-bolts of suitable size and making good the disturbed surface of wall with OBD/White wash to match with old surface. Note : Old unsv exhaust fan shall be deposited to MES sotre yard by the contractor.

Supply & fixing water storage heater 25 ltr capacity, 5 Star rated, vertical type, Glass line, AC, vertical type, AC, Single Phase electric, 230 Volt, complete with heating element, thermostat, 3 core lead, Plug top, safety valve, including electric and water connection with suitable nut, bolts & washers and making good to disturbed surface complete all as specified and directed by Engr-in-Charge.

S&F of Wall mounted LED Integrated Batten T5 20 Watt - 4Ft White, indoor decorative PVC extruded T5 LED battern-Integrated complete all as specified and directed by Engr-in-Charge.

S&F of Wall mounted LED Integrated Batten T5 10 Watt-2 Ft White, indoor decorative PVC extruded T5 LED battern-integrated type complete all as specified and directed by Engr-in-Charge.

S&F in replacement of LED 12W roof light panel of 1 x 1 feet as per sample recees mounted LED luminaires made in CRCA sheet metal with wider light window with opal diffuser for sportless glare-free uniform lighting, with including flixble wire all as taking down of UNSV 1 x 1 panel complete all as specified and directed by Engr-in-Charge.

S&F PVC connection with brass nipple 15 mm x 600 mm long with ISI marked, stainless steel, suitable for hot and cold water of 25 ltrs capacity of geyser as hot and cold water connection complete all as specified and directed by Engr-in-Charge.

Notes for BoQ:- The contract sum shall be after deducting the amount of Credit shown in Credit Schedule of this Tender.

M/S.M.S.Devi.Const.Co

JINDAL ENTERPRISES

SHIV INFRA

Chaudhary Constructions

A N BUILDERS

Kunal Construction Co.