SPECIAL REPAIR TO BLDG (P-10) E/M INSTALLATION DIPR AND DIPAS AND REPAIRING / RE-CONSTRUCTION OF PARAPET WALL AND PORCH BEAM OF MAIN BUILDING AT DIPR AT KWC AREA UNDER GE I RnD DELHI.

Amount

Taking down cement plaster from brick or stone wall or concrete surfaces etc including racking out joint, hacking for key scrubing down with water etc complete all as specified and directed.

M&L for 15mm thick rendering on brick work or concrete surfaces in CM (1:6) finished even and fair without using extra cement complete all as specified and directed.

M&L for 15 mm thick Rendering on brick work or concrete surfaces in CM (1:4) such as in wall and similar work finished even and fair without using extra cement complete all as specified and directed.

M&L for 5 mm thick Rendering on brick work or concrete surfaces in CM (1:3) such as in ceiling and similar work finished even and fair without using extra cement complete all as specified and directed.

M&L for Rough cast plaster including 15mm thick rendering in CM (1:3) on brick work or concrete surfaces complete as specifed in SSR Part -I clause 14.22 complete all as specified and directed. Note:- Rough cast finish to be as below :- After applying the under coat of cement mortar (1:3) and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generallly of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of (1:1:1) shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered.

Complete removal of existing treatment from internal/external plastered or unplastered surfaces of walls complete all as specified and directed

M&L for applying two coat of wall care putty (Each coat minimum 1mm thick) on wall including preparation of surfaces complete all as specified and directed.

M&L for applying two coats of distemper oil emulsion on wall including preparation of surfaces complete all as specified and directed.

M&L for two coats of acrylic exterior emulision (weather proof paint) of any tint including priming with alkali resistant primary paint on external cement plastered surfaces complete all specified and directed.

Complete removal of existing treatment from plastered or unplastered or concrete surfaces of ceiling including preparation of surface complete all as specified and directed.

M&L for two coats of white wash on old plastered surfaces of ceiling complete all as specified and directed.

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed.

M&L for chipping of spalled and loose concrete and cleaning rust from reinforcement by sand blasting scrubbing down concrete surface with wire brushes cleaning with water allowed to dry and applying a layer of zinc rich epoxy primer as antirust on all exposed reinforcement followed by a layer of bounding coat of approved epoxy adhesive on complete exposed surfaces of concrete to be gunited all as specified and applying two layers of guniting over steel welded mesh 2mm dia of wire and aperture 75mm, total thickness of gunite n.exc 40mm thick (average thickness) in cement mortar (1:2) using OPC 53 grade cement mixed with polycrete admixture @ 2% by weight of cement or as per manufacturer instructions and finally applying cement plaster over gunite surface of required thickness to give even uniform and smooth finish conforming to proper geometrics in cement mortar (1:3) to match the existing surface as in sides and soffits etc of slabs, chajjas, fins, facias,parapets, lintels, columns and beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 6 storey building including removing of small trees shrubs etc all as specified and as directed.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm thick cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm thick cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with and including groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified Note: (i). Rate also includes necessary scaffolding to carry out stone grit plaster work upto a height G+6 floor. (ii) Payment for providing grooves shall be measured & paid seperately.

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone girt plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and direction of the Engineer -in-charge.

M&L for Roughening of surfaces of old concrete slab by wire brushing, sweeping, cleaning and washing down to remove all loose dust etc. incl grouting with cement slurry mixed with water proofing compound and brushing neat cement slurry @ 3.00 kg/Sqm on roof surface, complete all as specified. Notes:- (i) Injection grouting to the surface shall be done with manually operated with frout with cement slurry impregnated with COBEX-100 for Fosroc Chemical. The cement slurrly shall be at first instance 1:1 (water and cement) and after that it shall be 1:1 ½ (1 water and 1 ½ cement) (ii) Grout will be allowed to curing for minimum of 48 hours and the hole after removal of nipple will be refilled with grout.

Demolition of brick work built in cement mortar of any description complete all as specified and directed.

M&L for brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) etc complete all as specified and directed.

All as per ser item No 18.00 above but except bricks complete all as specified and as directed. Note:- Serviceable bricks obtained from item No 17.00 shall be reused.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provide for complete all as specified and directed.

S&F Rolling shutters 1.25mm thick laths , without ball bearing, as specified including top cover, an anchoring rod, haps and staple and one shop coat of primer, erected in position as indicated, complete: push pull or manual type complete all as specified and directed.

S&F Safety lever lockss mild steel with 4 levers for rolling sutter complete all as specified and directed.

S&F ball bearing for rolling shutter ccomplete all as specified and directed.

M&L for painting to steel surfaces of any description not other wise described over 10cm width or girth with two coats of synthetic enamel paint over one coat of red oxide primer incl preparation of new surfaces complete all as specified and directed.

Taking down chowkats or frames n.exc 1.5 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc complete all as specified and directed.

Taking down chowkats or frames with shutters ( without taking off shutters from the frame area 1.50 sqm but not exc 4 sqm including making holes as required for receiving PCC and to match with the existing wall surface complete all as specified and directed.

M&L for Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

M&L for Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

M&L for PCC 1:3:6 type C-1 (20 mm graded stone agg as in filling pressed steel frame /hold fast blocks etc

S&F for 35 mm thick flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specified and directed.

S&F for 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F for Butt hinges, 100mm size extruded aluminium alloy with anodised galvanised , with mild steel hinge pin, and fixed, type B-21 complete all as specified and directed.

S&F for 250mm size aluminium alloy anodised sliding door bolt with hasp & staple ( bolt type ) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

S&F for 150mm size aluminium handles, cast type anodised complete all as specified and directed.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick wood grain printed PVC sheet reinforced with M.S. Square tube, suppling and fixing in opening as per specification & drawing complete all as specified and directed.

M&L for Factory made solid panel PVC wood grain printed door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side &as gap insert for top rail & bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to gathers with solvent cement supplying & fixing the frame at site complete all as specified and directed. Make : Rajshri/SINTEX (Make should be engraved on item )

S&F for factory made steel ventilators/window box type glazed shutter made out of 16 gauge steel section for frames & shutters as per drawing No TD-A sheet No. 01/03 to 03/03 with openable glass shutters including pintel hinges 75mm long 12mm dia, 100mm long handle and tower bolt 150mm long, MS hooks & eye 150mm long all as applicable including one coat of red oxide primer complete all as specified and directed. Note:- Glass shall be measured and paid separetely

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars all as specified and directed

Hacking out old broken glass any thickness/size quality or description from metal / steel frame etc complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n-exc 0.50 sqm in each pane etc complete all as specified and directed.

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for and all as specified and directed.

M&L for 25 mm thick Plain cement concrete 1:2:4, type B0 (using 12.5mm graded stone aggregate) as in flooring, complete all as specified and directed .

M&L for 18-20mm thick machine cut kota stone (table rubbed and polished) as in flooring laid over and including 15 mm thick screed bed or bedding layer in CM (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, rubbing, grinding and mirror polishing complete all as specfied and directed.

M&L for machine cut kota stone 18-20mm thick as in skirting,risers of steps laid over and including 10 mm thick rendering in CM (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specfied and directed.

M&L for demolition of stone slabs/old granite / Kota stone as in plateform and tiles / floring of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all specified and directed.

M&L for 18 to 20mm thick granite stone slab as in shelves, in steps, jambs, pillars, window cills, cooking platforms, flooring and like work ,machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid over 15 mm thick sereed bed in CM 1:6 etc complete all as specified and directed.

M&L for 18 to 20mm thick granite stone slab on vertical surfaces such as skirting/dado including grinding and polishing etc set and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone and beveling half round edges of stones fixed over and including rendering 10 mm thick in CM 1:3 complete all as specified and directed.

M&L for dismantling of floor tiles / hearth of wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

BLANK

M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) joint less / joint free, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match colour of tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for light colour fully vitrified ceramic tiles 9 to 10 mm thick (Square/rectangular) joint less / joint free, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match colour of tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

All as per ser item No 54.00 above but on vertical surfaces i.e dado/skirting etc over and including 10mm thick rendering in CM 1:4

M&L for Ist quality glazed ceramic coloured designer tiles of size 450x300x7mm thick on vertical surface as in skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over 10mm thick rendenring in CM 1:4 on brick wall complete all as specifie and directed.

S&F in repair 2.5 mm thick Rubber tiles/mats/sheets with fabric backing or insert, plain coloured or marbled topping, matt or glossy, laid in floors with approved adhesive and ribbed or fluted topping as per IS-15652 etc complete all as specified and directed.

S&F Mild Steel Framed work such as guard bar/grill welded to window frame or fixed independantly, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Dismantling old unserviceable PVC water tanks of capacity exc 250 ltrs & n.exc 500 Ltrs including supplying & fixing of PVC water storage tank 500 ltr capacity HDPE double layered , cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia including tank nipple and (Minimum weight 20 mm - 210 gms ) complete all as specified and directed. Note : (i) GI inlet, outlet & wash out pipe will be measured & paid for separately.

Taking up or down 20 mm bore steel tubing & connection including. cleaning for refixing serviceable tubing complete all as specified and directed.

Taking up or down 15 mm bore steel tubing & connection including. cleaning for refixing serviceable tubing complete all as specified and directed.

S&F steel water tubing 20 mm bore, medium grade , galvanised with all fittings and fixed complete to walls and ceiling or laid in floors etc complete all as specified and directed. Note:- Cutting chases for concealing the pipes & fittings etc wherever required and making good, disturbed surface in Cement mortar (1:3) complete shall be included in the quoted rate.

S&F steel water tubing 15 mm bore, medium grade , galvanised with all fittings and fixed complete to walls and ceiling or laid in floors etc complete all as specified and directed. Note:- Cutting chases for concealing the pipes & fittings etc wherever required and making good, disturbed surface in Cement mortar (1:3) complete shall be included in the quoted rate.

S&F in repair Bib Tap fancy type cast copper alloy with crutch or butterfly handle but fancy type chromium plated, screwed down, screwed for iron pipe of 15 mm bore etc complete all as specified and directed.

S&F in repair 15 mm dia brass chromium plated pillar tap, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut, capstan head, screwed for 15mm dia pipe complete all as specified and directed.

S&F in repairs angle valve/stop valve fancy type chromium plated, cast brass copper alloy, screwed down, high pressure with crutch or butter-fly handle screwed both ends for 15 mm bore iron pipes complete all as specified and directed.

S&F in repairs ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia complete all as specified and directed.

S&F in repair PVC connection 45 cm long with brass check nuts on both sides suitable for 15 mm bore iron pipe complete all as specified and directed.

S&F in repair brass chromium plated towel Rail of size 600 mm with lower hanger brackets fixed to wall complete all as specified and directed.

S&F for WC Orissa pattern size 580 x 440 mm of vitreous china (white) fixed with all including accessories including integral footrest including taking down old WCs etc complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 ltr capacity sleek having weight not less than 1.80 KG including PVC bend, supporting brackets and complete accessories white colour as in repair etc complete all as specified and directed.

S&F in repair urinal, Half stall type,white with grating, union for discharge pipe, flush pipe and waste pipe, PTMT urinal Spreader fixed to water supply pipe etc complete all as specified and directed.

S&F in repair vitreous china wash basin white flat back size 580x 450mm excluding taps but incl 32mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets complete all as specified and directed.

Dismantling 100 mm bore cast iron soil, waste and vent pipes fixed on walls or laid in floors including fittings and taking out including removing from site complete all as directed .

Dismantling 75 mm bore cast iron soil, waste and vent pipes fixed on walls or laid in floors including fittings and taking out including removing from site complete all as directed .

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed to walls complete all as specified & directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 110mm PVC(SWR) bends any radius complete all as specified and directed.

M&L for 150mm x 150 mm salt glazed stoneware gully traps , square or round mouthed, type `P' including cast iron grating and fixed including necessary excavation and eath work, concrete in bed, surrounds, kerbs etc and jointing to drains in CM 1:1 complete all as specified

Removing building materials etc., to a distance out side MoD land in low laying area including loading, unloading and transporting complete all as directed

Dismantling bricks tiles or concrete tiles single layer on roofs and removal, complete all as specified and directed .

Demolition of mud phuska on roofs any thickness including mud plastering (whether full thickness removed or only a part thereof) and removal to a distance out side MoD land in low lying area complete all as specified and directed.

Roughening of surfaces of old concrete slab by wire brushing, sweeping, cleaning and washing down to remove all loose dust etc. and brushing neat cement slurry @ 3.00 kg/Sqm on roof surface, complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L Water proofing treatment over roof at any height consisting evenly applied primer coat @ 0.30 litre/ Sq. m on surfaces, overlaps, joints etc and including a layer of APP polymer 3 mm thick even membrane weight not less than 3.00 Kg/ Sq.m duly sealed at over laps joints with flame (complete by torch application) all as per manufacturer's instructions, over and including 15 mm thick screed bed of cement mortar (1:4) mixed with water proofing compound @ 2% by weight of cement, complete all as specified and directed Note:- (i) Water proofing compound shall be measured and paid separately. (ii) Application of polymeric membrane shall be by torch application. (iii) The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (iv) Primer shall be applied after preparing & cleaning of fully dried cement plastered surface.

M&L for Cutting or uprooting grass on old mud phuska, removing rubbish off the premises, cleaning surface and preparing to receive new mud plaster etc. complete all as specified and directed.

M&L for 40 mm thick brick tiles laid on roof and jointed and grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement over and including 15 mm thick screed bed in CM (1:4) complete all as specified and directed.

All as per Item No. 88.00 above but except tiles. Note:- Serviceable tiles retrieved from Serial item No. 82.00 here-in-before shall be used.

M&L for plain cement concrete (1:2:4) type B-0, using 12.5 mm graded mechanically crushed stone aggregates as in roof kerbs, benching and the like, as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for as in Manhole/Septic tank/Soakage well cover slab, Chajja, shelves, lintel band etc complete all as specified and directed.

S&F Factory made precast light duty drain/manhole covers with MS frame and reinforcement complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams complete all as specified and directed.

M&L for mild steel 10 mm dia and over TMT bar cut to length, bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Supply and fixed Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Demolition of reinforced cement concrete as in parapets wall at a height G+5 roof floor of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) in Fins, fascias, louvres, parapets wall, and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) in slab supported on walls, landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers weathering, throating etc and set in cement mortar 1:4 including formwork complete with joints to match etc complete all as specified and directed.

S&F for reinforcement steel (TMT bars) 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than 9mm dia complete all as specified & directed

Use & waste of form work to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses etc. vertical or to better for fair finished complete all as specified.

Use & waste of form work to to fins, louvers, fascia for fair finished complete all as specified & directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams complete all as specified. Note for Ser item No 93.00 to 103.00 :- 1. Rate also includes necessary scaffolding, T&P to carry out Demolition work upto a height G+5 floor. 2. Necessary precuation should be taken by tenderer while demoltion at high level height works.

Demolition of cement concrete in ground floor and paving n.exc 15 cm thick below or above ground level including removing from site out side MoD land in low lying area complete all as specified and directed.

M&L for PCC (1:4:8), type D2 (using 40 mm graded mechanically crushed stone aggregate) as in foundation, filling, mass concrete and sub base of floor complete all as specified and directed.

M&L for pre-polished coloured chequred cement concrete tiles 30cm X 30cm X 20-22mm thick, with white cement and pigments, set, jointed and pointed in neat cement slurry in floors over and including screed bed 20mm thick in CM (1:6) complete all as specified and directed.

M&L for factory made PU moulded polished with coating material, concrete interlocking coloured paver block with Grey cement and pigment, any shape and size, 60 mm thickness, M-35 grade over and including 40mm thick sand cushion and also including dismantling old tiles complete all as specified and as directed.

Taking down carefully point wiring aluminium (light, fan, socket, and power) complete fittings such as switches, ceiling roses, pendent, regtulators, sockets etc making good the disturbed surfaces complete all as specified and as directed.

M&L for point wring for one light/ceiling fan controlled by one switch with 1.5 sqmm (nominal area) PVC insulated and PVC unsheathed multi stranded copper conductor cable FRLSH in and including concealed PVC conduit 20 mm dia medium duty ISI marked, including sutiable new steel sunken boxes,modular frame and cover plate for fixing of modular switches as per required point in that board, flush to surface for one light point, fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 sqmm copper conductor cable FRLSH connected to common earth dolly complete including cutting,chasing the surface and then making good the same in CM 1:3 complete all as specified and directed.

All as per item No 109.00 above but socket 3 pin 5 Amp 230 volt flush type on same board.

All as per item No 109.00 above but for one socket point outlet 3 pin 5 Amp on independent board.

All as per item No 109.00 above but for one socket point outlet 3 pin 15 Amp with 2.5 sqmm PVC copper conductor and 2.5 sqmm PVC insulated copper conductor as earth continuity conductor.

S&F modular switch flush type 5/6 Amps 230V AC complete one way. Make : Crabtree or equivalent in legrand /Havells.

S&F one switch and one socket modular type 5 PIN 5 Amp 230 Volts AC complete all as specified and directed. Make:- Crabtree or equivalent in legrand/Havells(Switch and socket shall be same make).

S&F one switch and one socket modular type 3 PIN 15 Amp 230 Volts AC complete all as specified and directed. Make:- Crabtree or equivalent in legrand/Havells (Switch and socket shall be same make).

S&F regulator for ceiling fan modular electronic step type120watt- 2module suitable for 1200/1400mm ceiling fan complete all as specified and directed. Make:- Crabtree or equivalent in legrand/Havells.

S&F ceiling rose surface type bakelite 65x50mm two to three terminal 230V complete all as specified and directed. Make : Legrand/crabtree/Havells

S&F RJ 11 telephone socket jack with shutter.

S&F lamp holder, PVC/Polycarbonate type with back plate suitable for retrofit lamp complete all as specified & directed..

S&F Retrofit LED lamp 12 watt complete. Make: Cat part No. LTHPLEDLAMP12WB22BULB of C&S or equivalent in Havells/Bajaj/Wipro

M&L in replacement wiring for circuit/submain wiring along with earth wire with the 2x6 Sqmm+1x6 sq mm earth wire of FRLSH PVC insulated copper conductor single core cable in and including conduit pipe 25 mm external dia medium grade including pvc all accessories complete all as specified and directed.

S&F of LED aluminium extruded suspended light along with fixture 20 Watt and making all electric connections with two core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm including taking down old unserviceable light fitting complete all as specified and directed. Make: Cat Part No Consta544lP20Wled830sPmmaWH of Havells or equivalent in Bajaj/ Philips/Wipro.

S&F of LED tube light along with fixture .20 Watt and making all electric connections with two core PVC insulated, PVC sheathed copper conductor flexible cable 1.5 sqmm including taking down old unserviceable light fitting complete all as specified and directed. Make: Havells Cat part No ENDURALINEARNEOBS20WLED840SPCWH or equivalent of bajaj/ Philips/Wipro.

S&F light fitting 2x2, 36 W including driver recess mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and separate replaceable electronic driver including taking sown old unserviceable fittings complete all as specified & directed.. Make:Havells Cat Part No ENDURASLIMPROPLUS 2x2PLR28/36WLED840MOD or equivalent of bajaj/ Philips/Wipro.

S&F LED flood light fitting with pressure die cast aluminium housing , complete with all accessories of 70W making all electric connections with two core PVC insulated, PVC sheathed, copper conductor flexible cable 1.5Sqm including taking down old unserviceable fittings complete all as specified & directed. Make: Cat Part No Havells JETAFLAREFL70WLED757LTG or equivalent in Bajaj/ Philips/Wipro.

Taking down of existing Ceiling/ Exhaust fan of any size and refixing the same after repair of the fan including painting and testing the serviceability of the fan complete all as specified and directed.

S&F of MCB distribution board double door/ metal door vertical type made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating, TPN 8 way, 415 volts with bus bar rating 200 Amps, dust and vermin proof and IP 42 - IK 09 protection suitable for incorporation of MCB, including grouting in the wall, cutting & chasing etc complete all as specified and directed.

S&F of sheet metal enclosur double door SPN 8 way with 240 V 200 Amp rated busbar all as directed.

S&F MCCB 415 Volts 100 Amps, 25KA 04 pole 'C' series complete all as specified & directed.

S&F MCB 240 Volts 63 Amps, 10KA SPN 'C' series complete all asspecifie.

S&F MCB 240 Volts 6 Amp to 32 Amp SP 10 KA 'C' series complete all as specified.

S&F rigid non- metalic PVC conduit of size 25mm dia inclusive of all tees,bends, elbow, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook etc over the surface/recess comlete all as directed.

Supply , installation, testing and commissioning of plug-in type ionisation addressable analogue smoke detectors with twin blinking LED and this will glow in case of fire with 5 levels of sensitivity bands for adjustment of clean/harsh area and day & night mode to avoid false alarm. The operating temperature of the detector should be from (-) 30 to 70 degree. The detector should have drift compensation and should have non volatile memory to have his own event log. It should have a facility to act as conventional detector in case of panel failure with operating voltage 17-28V DC, complete all as specified and directed. The detector should be EN-54/LPCB/UL/VDS approved. Make-Apollo, Cat Part No 58000-500/Notifier(Honeywell)/Sharack/Hochiki or equivalent approved.

S&F telephone cable of two pairs (2P) 0.5 mm size in concealed non metalic rigid PVC conduit 20mm dia including fittings of suitable size, connecting in telephone socket complete.

M&L for earthing with Galvanised iron earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal GL) with top of earth plate not less than 1.5 metre below GL connected to GI earth Strip 32 x 6 mm connected to earth plate electrode by means of GI nuts, bolts & washers earth wire protected with & including 40 mm dia medium grade ISI marked GI pipe not less than 7.5 metre long all as shown in electrical plate No 3 of MES Schedule Part I, with & including; PCC 1:3:6 type C1 pit with cover of RCC 1:2:4 B1 reinforced with welded steel wire fabric not less than 4 Kg per Sqm watering arrangements with 20 mm GI medium grade pipe ISI marked , GI funnel with GI mesh, filling with mixture of common salt & charcoal including necessary excavation and earth works in any type of soil, including test point, testing & commissioning complete all as specified & directed.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32x6mm galvanised iron strip.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required but GI Wire 4mm dia complete all as specified & directed.

M&L in replacement of Air termination, single pointed aluminium rod 12mm dia and 300mm long including clamps, nut & bolt etc & necessary PCC work for grouting of air termination rod complete all as specified & directed.

M&L Test point terminal block made of gun metal or phosphorus bronze size 75X75X25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. Head screw complete all as specified and directed.

S&F in replacement of Aluminium strip 25X3.15mm with saddles and fixing screws etc for roof conductors and down conductors upto test point and further connected to ground conductor complete as specified and directed.

M&L for earthing with Galvanised iron earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal GL) with top of earth plate not less than 1.5 metre below GL connected to GI earth Strip 25 x 4 mm connected to earth plate electrode by means of GI nuts, bolts & washers earth wire protected with & including 40 mm dia medium grade ISI marked GI pipe not less than 7.5 metre long all as shown in electrical plate No 3 of MES Schedule Part I, with & including; PCC 1:3:6 type C1 pit with cover of RCC 1:2:4 B1 reinforced with welded steel wire fabric not less than 4 Kg per Sqm watering arrangements with 20 mm GI medium grade pipe ISI marked , GI funnel with GI mesh, filling with mixture of common salt & charcoal including necessary excavation and earth works in any type of soil, including test point, testing & commissioning, complete all as specified & directed.

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. of size 25x4mm galvanised iron strip including taking down old GU/S strip complete all as specified & directed.

M&L in relacement of GI tube light grade laid in PCC Foundation and protection/fixed air termination single pointed aluminium rod and strip protection as required for the size 40mm bore complete all as specified and as directed.

JM enterprises