Supply of Machinery Equipment

Amount

DEPARTMENT OF CIVIL ENGINEERING

Compression Testing Machine : Computerized 2000 KN least count 0.05KN. Load accuracy + 0.5% with PC and software with standard accessories for compressive testing. Complete with manual. The Installation, Commissioning and Training should be included in the offer. Conforming to IS: 14858(2000) and calibrated with an accuracy of ± 1% as per the requirement of 1828(Class1) .

Vee Bee Consistometer :- As per IS119 consisting of vibrating table 380mm long and 260mm wide. Resting upon elastic support at a height of about 305mm above the floor Complete with start/stop switch, cord and plug. A holder is fixed to the base into which a swivel arm is telescoped with funnel and guide sleeve. The swivel arm is also detachable from the vibrating table. A graduated rod is fixed on a swivel arm and at its end a plastic disc is screwed. The divisions of scale on the rod record the slump of the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16mm dia and 600mm long, rounded at one end.

Standard Concrete Cube Moulds:- 150x150x150 size.(Heavy Duty)

Vibrating Table: 60cm x 60cm

Aggregate Impact Tester:- as per IS 2386 part IV. Quick release mechanism to ensure effective fall of hammer during test. The free fall can be adjusted .380mm. The hammer should be provided with lockage arrangement. Fitted with mechanical counter. Complete with manual.

Aggregate Crushing Value Apparatus: As per IS 2386 part iv complete with manual.

Standard Sieve Set for coarse aggregate as per IS standard 30cm dia made of G.I frame with joint I.S meshes complete set with lid.

Standard Set of Sieve for fine aggregate as per IS 460 1962 made of polished brass frame, without joint and tightly fitting with each other 4.75mm to 75 micron is sieve with lid complete.

Digital Balance 5Kg, 10 Kg, 15 Kg (Platform Type) capacity sensitivity 1gm, 1 no each

Physical Balance with weights

Steel trolley (heavy duty) for carrying load upto 500 kgs

Penetrometer Apparatus: as per IP 49, 50 & 167 specification and also per IS 1448 (P:92) & (P:93) for penetration test of wide variety of materials like, bitumen, greases, wax, polish etc. Complete with electronic trimmer & electric arrangement with brass cone and needle complete with manual.

Ductility Testing Machine:- as per IS 1208 consisting of thermostatically controlled bath with inlet and outlet tap complete with moulds and plates, Thermometer etc and manual.

Centrifuge Extractor:- as per ASTMD-2172, AASHO T-58, T-64, T-164 for determination of Bitumen %age in bituminous mixture electrically operated.

Softening Point Apparatus:- according to IP58 & IS 1205-1958 with F.H.P electrical motor driver, Stimer and electric heater with transporates regulator control

Direct Shear Apparatus:- Confirming to IS 2720. Shear velocity adjustable between 0.00001 and 6 mm/min Maximum shear force: 5000 N Vertical load ratio: 10:1 Maximum vertical load: 500 N Maximum vertical load using the lever: 5500 N Shear box and accessories made of brass. Power supply: 220-240 V 50 Hz, single phase Dimensions: 1100 x 1200 x 550 mm Weight: 150 Including PC and Software

Unconfined Compression Test Machine: Electrically cum hand operated as per IS 2720 part x consists of lead frame, proving ring of capacity 5 KN and 50KN and two dial gauges, three rate of travel 1.25mm, 1.5mm & 2.5mm. Set of plain platen and conical platen to test specimen size 38mm, 50mm, 75mm & 100mm.

Standard Penetration Test Apparatus:-As per IS 2113 (SPT) to conduct STP & estimate value of “N” with: i) Split spoon sampler. ii) Extension rod with coupling (A rods) 5ft long heavy duty. iii) 65kg driver wt with penetration guide assembly with 75cm fall designed. iv) Tripod 18’ with high and sleeve. v) Spanners (set of two) vi) Avger 6” dia with extension rods for bores. vii) 50.8mm 60 threaded cone for dynamic cone penetration. viii) Casing pipe. ix) Guide pipe assembly. x) Pulley.

Vane Shear Test :- Laboratory purpose as per IS 270 part xxx electrically operator rates of rotation 1/60 rpm simple phase complete with manual.

Consolidation Apparatus:- For single sample complete with 2 no dial gauges and consolidation ring as per IS specifications

Falling Head Permeability Apparatus: for determination permeability studies of soil with over head tank and mould As per IS 2720 part xvii complete with manual.

Automatic Level. Specifications: Magnification 32x, Standard deviation per km (double run level)= 2.0mm Accessories: Stand: Aluminium (heavy duty)-1no Staff: Aluminium (4m folding)-1no

Electronic Theodolite (including all standard accessories) Specification: Telescope: Image erect, magnification 30x, effective aperture 45mm resolving power 3’, field of view 1 30’ Minimum focusing distance = 1.5m Measurement = Minimum reading 1” Display : LCD screen, both sides Level: vertical till compensation range = 3’ with setting accuracy 1” Accessories: Diagonal eyepiece, adoptor, toolkit, battery holder, handlany case Almunium heavy duty stand.

Digital Theodolite: Specification: 2” angle accuracy, 30 x telescope, clear aperature 45mm two faced LCD display.Till compensation automatically, range o compensator + 3’ nickel hydrogen chargeable battery. Accessories: all standard accessories included complete with manual and training of staff.

Ranging Rod:- Steel Rods 10 ‘ height

Total Station: Specification: 2mm = 2ppm high distance accuracy, 2” angle accuracy, dual-axis compensation (range = 4’) 10hrs battery backup High productivity with alpha numeric keyboard. Internal memory not less than 10,000 points. Accessories: Heavy duty aluminium tripod 2 no Prism polygon-2no with prism poles Prism 2no Software (Data down loaden) Data case and toolkit.

Prismatic Compass :- 4” Prismatic Compass with brass tripod

Plane Table complete with all standard accessories. Specification: Plane Table Board: 600 x 750 x 16mm Plane table stand: Aluminium, heavy duty Plane table head: 151 specification ball and socket type. Magnetic compass: 150mm brass Spirit level: 150mm brass Alidade : telescopic ( ISI standard) Pancake coils single layer: brass Plumb bob : brass Canvas cover: Full

Pipe Friction Apparatus: (Closed circuit) This apparatus is used to measure Darcy’s coefficient “f” for given pipes.

Bernoulli’s Theorem Apparatus:- (Closed circuit) This apparatus is used to verify Bernoullis Theorem

Notch tank Apparatus:- (Closed circuit) The apparatus should measure coelf of discharge of various shape, v-notch of angle 60, rectangular Notch 100 x 150mm.

Venturimeter /orifice apparatus: Use to determine the discharge of water in pipe.

Discharge measuring apparatus through orifice meter

Apparatus for conducting orifice coefficients(cd, Cc & cv): The apparatus is used to measure coefficient of contraction coefficient of discharge and coefficient of velocity of different type of orifices.

Hydraulic Bench : Complete with tank and AC motor for circulation of water. Complete with accessories.

Differential Manometer for measurement of pressure difference.

Meta Centric Height Apparatus: Apparatus is used to determine the meta centric height of a ship model under load and unload condition. (Flat bollomed versel).

Digital PH Meter:- 3 ½ digit LCD, 0 to 14ph accuracy Io.1 ph. Manual lamp compensation 0-100c, IV DC battery electrode stand supplied with combined electrode, doffer solution, electrode stand.

P H Meter Pen Type:- 0-14ph, accuracy I 0.2 ph. Temperature 3 ½ digit LED display.

Floculator:- With illuminated base having florescent tube fitted below fluorescent plastic plate. Consists of geared 1/20 HP variable speed from 10 to 100 RMP with speed control. Fitted with SS stirring rods, electrically operated suitable to work on 220v. With 4 stainless cap 1 lt/ 2lt Digital RPM indicator for above

Dissolved Oxygen Meter:- (Portable) 3 ½ digit LCD displays (CWM)

Portable Digital TDS Meter: Display 3 ½ LED 0 – 1999ppm, 0 to 19.99ppt Acc 2 % FS IV DC battery operated. Supplied with conductivity cell housed in ABS cabinet. Complete with manual.

Residual Chlorine Meter as per Indian Standards

Digital conductivity meter (Portable):- 3 ½ digit LCD display 0 to 1999 ms, 0 to 19.99 ms Accuracy 1% in ABS plastic cabinet with touch switches battery operator.

DEPARTMENT OF ELECTRICAL ENGINEERING

D.C shunt motor coupled with D.C Shunt generator 3hp motor ,5kw 1500rpm Generator including Control Pannel Board

D.C series motor coupled with D.C Series generator 3.5 KW,230 V,1500 rpm DC Series Motor Coupled with 3KW,230V,1500 rpm DC series Generator including Control Pannel Board.

D.C Compound motor coupled with D.C Compound DC generator 5 H.P.,220V DC,1500 rpm DC Shunt Motor Coupled with 3KW, 220V DC,1500 rpm DC Shunt Generator including Control Pannel Board

Three Phase Induction Motor ,3H.P, 440V,50 Hz,1500 rpm. Squirrel Cage Induction Motor having all Terminal on Terminal Box with Star/Delta Starter, Belt & Pully loading arrangement including Control Pannel Board.

3-Phase Solid state DC Source Static 3 phase Converter ,Input -440 V AC, 50 Hz,out Put 0--240 V DC,50A Including Control Pannel Board

SCR V-I Characteristics ,TRIAC V-I Characteristics and DIAC V-I Characteristics kit (Experimental Board ) Experimental Trainer Board comprising of experimental setup for performingV-I characteristics of SCR , DIAC AND TRIAC.The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2. On/Off switch 3 .Protection against high current and transients. 4.Operating manual with detail procedure andspecifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

UJT Characteristics and UJT Relaxation Oscillator Kit (Experimental Board ) Experimental Trainer Board comprising of Experimental setup for UJT Characteristics. The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2. On/Off switch 3.Protection against high current and transients. 4.Operating manual with detail procedure andspecifications of components used . 5.Suitable numbers of Banana Patch cord(min. 4mm) required for the ETB

Single phase half controlled and fully controlled full wave rectifier Using Thyristors (Experimental Board ) Experimental Trainer Board comprising of Experimental set up for SCR based single phase half controlled and fully controlled full wave rectifier. The whole experimental set up must be marked(printed) on the sheet (PCB sheet) with specification of each component used and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2. On/Off switch 3.Protection against high current and transients. 4. Provision for observing waveforms on CRO. 5.Operating manual with detail procedure and specifications of components used 6.Suitable numbers of Banana Patch cord(min. 4 mm) required for the ETB

Digital Trainer Kit for verification of logic Gates . Expt. Board for verification and interpretation of truth table for Logic gates Inbuilt Power Supply alongwith individual terminals of all components with connecting leads for AND, OR, NOT, NAND, NOR, XOR, XNOR, Gates.

3 HP ,230 V,1500 rpm Dc Shunt Wound Motor With loading arrangement & control Pannel Board.

Flip Flops (Experimental Board ) Experimental Trainer Board comprising of Experimental setup for study of Flip Flops(RS,JK, master slave J-K,D and T ). The. whole experimental set up must be marked(printed) on the sheet in the form of logic diagram and should be duly housed in a suitable metallic/robust enclosure. The board must include the following facilities: 1.In built power supply with indicator 2 On/Off switch 3.Protection against high current and transients.4. Provision for logic inputs with display, output display(LEDs), 5.Operating manual with detail procedure and specifications of components used 6.Suitable numbers of Banana Patch cord. required for the ETB.

8085 micro Processsor trainer Kits User Memory : 8 KB Input : ASCII Keyboard Display : 20 X 2 LCD Power Supply : 110V - 260V AC, 50/60Hz Battery Backup for RAM Learning manual .

8051 Microcontroller Trainer Kit, operating at 11.0592MHZ. EPROM.64KB on chip Flash memory ,Two 16 – bit programmable on chip Timer.50 pin FRC connector for system bus expansion.Facility to connect to PC. Supports Assembly and “C “ language

Desert Cooler 24 '' x 30'', Fan Motor 0.5 hP

Digtal Clamp-On- meter Jaw Size 50 mm,AC/DC 0-200 A, DC 0-500 V, AC 0-700 V fluke

Construction Of Half Adder and Full Adder (Experimental Board ) Experimental Trainer Board comprising of Experimental setup for Construction of Half Adder and full Adder. The. whole experimental set up must be marked(printed) on the sheet in the form of logic diagram and should be duly housed in a suitable metallic/robust enclosure.

Function Generator Range 0.3 Hz to 10 MHz with Sine , Square , Triangle waveforms Square Wave Rise time typ. 70 ns , LED Display

Soldering and desoldering station

Contractor 15A,415V (4N/O,3N/C)

Crimping Tool capacity upto 300mm2 cable, Hydraulic

3 HP ,230 V,1500 rpm Dc series Motor With loading arrangement & control Pannel Board.

Power Measurement kit using CT, PT, Wattmeter 15- 1500w , CT Ratio 1 : 10 , Secondary current rating 2A , PT1 Ration 1 : 2 , primary 230v , secondary 115 v , Pt2 1: 4 , Primary 230 v, Secondary up to 60v

Ihp Automatic ceiling Fan Winding Machine with Coil Guides & Dies. 28- 38 swg

Washing Machine(Semi Automatic) 6 kg

Vacume Cleaner motor rating 1 kW

Electrical Machine Trainer for demonstrating the construction and functioning of Different types of Dc and AC Machines ( Should include machines as well control panael

Transformer OiI Test apparatus for measuring the Dielectric strength of Transformer oil with input 220 V,50 Hz Single Phase, testing voltage range from 0 to 100 KV,inbuilt Digital/analog Voltmeter,epoxy moulded bushings for HV terminals.2kv/sec

Electrical Transmission line Trainer Mains supply 230v +/- 10% , 5o Hz current 0-5A

Transformer differential Protection Trainer : 3 phase 3kva , 415/240 v , Delta Star Connected Natural Air Cooled with Differential Relay Static / Numerical relay type with minimum basic Setting Biased feature of 10% , 20%, 30%, 40% and 50% Secondary CT CURRENT 1A

Electro Technology Trainer for Studing DC circuits fundamentals ( OHMS LAW , KCL, KVL, Thevenin , Power , Resistance in series parallel ) Ac Circuit fundamentals single phase and three phase

Buchhloz Relay Testing Kit

Alternator Protection Trainer for protection from overcurrent , under/overvotage , under/Over frequency , Reverse power protection Field Failure protection , Negative phade sequence protection

Power Drilling Machine- chuck capacity upto 1’’ make Wolf , (with Bits)

Micro wave oven ; Including Grill & Utensils 32L

Refrigerator 250 L

Three phase Slip Ring Induction Motor 3H.P,440V,50 Hz,1500 rpm. Slipring Induction Motor (with Rotor Resistance/ DOL Starter) including Control Pannel Board and its loading arrangement.

3 phase Alternator coupled with dc shunt Motor 5kw coupled with 7 hp shunt motor including panel board and all accesories

Auto Synchronous motor 5KVA with excitor

1 Phase universal Motor 2 HP including panel board and all accesories

1 Phase Capacitor start Capacitor run motor 2 KV

1 Phase split phase Motor 2HP including panel board and all accesories

Synchronization of alternator Lamp Method including panel board and all accessories

Parallel operation of 3 phase transformer each capacity 10 KVA */Delta connections including panel board and all accessories

Transformer for conducting OC/SC test 5kva including wattmeter , ammeter, voltmeter(ac) including panel board and all accessories

CRO 100 MHz Digital

Kits for Ohms Law, Kirchoff Law, Series and Parallel Resistances, Nortans Theorem, Thevenins Theorem, Maximum Power Transfer theorem, Reciprocity Theorem and Superposition Theorem

Synchronouscope 3 phase digital type Synchronous cope with all accesories

PLC Trainer System Specifications: v PLC MAKE: ALLEN-BRADLEY MICRO 800 SERIES 2080-LC10-12AWA/ STD. EQUIVALENT. v Micro810 Controller, 8IN 120/240VAC, 4RLY, AC PWR v 8 Digital input / 4 Digital outputs. v 24VDC, 1.5A Power source.4”X2”X2”. v I/p- O/p LED indication on front panel. v PC interface facility. PC-PLC interfacing cable. v 2080-USBADAPTER: USB Adapter Plug for Micro810 12-pt only v 2080-LCD: 1.5 LCD Display and Keypad, for Micro810 Only v Necessary I/p-O/p simulating devices. v Ladder diagram programming on PC. v SCADA SOFTWARE connectivity for PLC.(optional) v Electrical control panel for simulation of digital .

Coil Winding Machine Standard Machine Specifications Base Plate Size 15" x 14" in inches Maximum Coil/Bobbin Diameter 8" in inches Maximum Centre Distance 5" in inches Maximum Axial Winding Length 4.5" in inches Wire Range 20-46 / 16-40 / 14 36 swg Choose any one of the following wire range No of Bearings 12 Main Gears Steel (Big) - Nylon (Small) Nylon gear is used for noise reduction Traverse Shifting Manual Traverse Type V-Bed Rod bed can be used for better winding of thinner gauge at additional cost Tensioner Standard Optional: Regular Tensioner can be used for wire gauge 28-40swg at additional cost Spool Carrier up to 5Kgs Approx Weight 35Kgs of the machine Additional Optional Accessories Motor 1/2 HP 1440rpm Single or Three Phase Marshall Make Clutch Foot Paddle Assembly Fabricated stand

1 Phase energy meter (induction type) Induction type 40A

1 Phase energy meter (digital type) Digital type 40A

1 Phase energy meter (electronic type) Electronic type 40A

DEPARTMENT OF MECHANICAL ENGINEERING

UNIVERSAL IMPACT TESTING MACHINE Working on Pendulum principle for Izod and Charpy test. Capacity: 30 kgf +/- 0.15 kgf, should be as per IS- 1499-1959. IS 1598, 1757

SPRING TESTING MACHINE. Electronic type , 1-100gms Displacement-: 50-200mm 5accuracy +/- 0.5mm Temperature 5-50 deg C Seven segment display. 30mm LCD

METALLURGICAL TRINOCULAR MICROSCOPE: Objective: 5 X, 10X,20X, 40X. Eye piece: 10X/ 22mm Nosepiece: Quadruple. Stage moving range: 250 mm × 250 mm coaxial coarse & fine focus adjustment system Illumination: Halogens lamp 6v20 V,adjustable brightness. Digital camera standard port.

ABRASIVE CUT OFF MACHINE: The rating is 2H.P provided with abrasive, grinding wheels capable of cutting different metals of various diameters. Table top direct cutting model ( Aluminium base) Motor capacity : 1 H.P, single phase Single illumination TWIN Cam operated vice Cutting Size : 40mm max. Wheel Size : 8” Front hood with large window Side opening for length specimen Coolant Jet Recirculating Coolant Chamber, Capacity : 30 litres

POLISHING MACHINES: Disc Size : 200mm Variable Speed 50-800 rpm No.of Disc: 1 No.of Motor: 1 Water flow: single

REFRIGERATION TEST RIG WITH COMPUTERISED CONTROL AND INSTRUMENTATION: Compressor : Hermetically sealed compressor. Condenser : Air Cooled condenser made out of copper pipe & Aluminum fins of matching capacity with fan cooling. Evaporator : Copper Coil immersed in water. Expansion device : Capillary Tube & Thermostatic expansion valve. Energy Meter : One each for power measurement of compressor & evaporator heater. Pressure Gauge : 2 Nos. for H.P., L.P. measurement. Suitable filter/drier. Hand Shut Off type Service valve. Dimmerstat to control power supply to heater. Rotameter for Refrigerant flow measurement. Immersion type electric heater. Solenoid valve. Set of thermocouples. 12 Channel Digital Temperature Indicator. HP-LP Cutout. Switches : For compressor, condenser fan, solenoid valve & evaporator heater. Voltmeter : 0 - 250 V. Ammeter : 0 - 15 A Thermostat. The plant should have design of simple and functional concepts able to visuals the main components of a compression refrigeration cycle.

DEPARTMENT OF AUTOMOBILE ENGINEERING

AUTOMATIC AIR CONDITIONING SERVICE UNIT :Type of refrigerant R134a, service process fully automatic ,display LCD monchrome 20*4,vaccum pump 1.8cfm,1/4hp,compressor 8.8cc, refrigerant bottle capacity 12 KG's, Power supply 230V

Automatic Tyre Changer. Rim clamping from inside: 12"-24"(305mm-610mm), rim clamping from outside:10"-20"(254mm-508mm),Max wheel dia 41"(1041mm),Max wheel width 3"-12"(76mm-305mm),operating pressure 6-8 bar,Bead Breaker force 2500kg ,power supply 220-380v ac, single phase 50hz, power 1 hp

Portable Hydraullic Jack: lifting capacity:3 ton, double plunger, min height 127mm, max height 460 mm

Portable Hydraullic Jack: lifting capacity:3 ton, double plunger, min height 127mm, max height 460 mm

Workshop Trolley 5 Drawer: 930*710*410 mm(H*W*D), Solid sheet steel Design, ABS top tray with recesses for small parts,Two streeing wheels 100mm dia, one wheel with locking, load capacity 300 kg

Pnuematic Auto glass removal kit 9 blade: Low air consumption from 1cfm(30 l/min) to max 5 cfm (140 l/min),Complete portability using a small air compressor, weight: 1.1 to 1.5 kg, moisture resistant lubricating oil

Pnuematic wrench: Free speed:8000 rpm, maximum torque 922 nm,working torque range: 34-542nm,air inlet: 1/4", average air consumption (4.2 cfm/120 l/min, fexible hose pipe with moisture seperator.

Two stage air compressor: power: 5 hp, no of cylinders 2, piston displacement: 501 L/min,compressor speed 925 rpm, air receiver 220 litres

Hydrualic press: Capacity 16 tonnes, stroke: 150 mm, height 1620 mm,width 885 mm, width between legs 640 mm, depth between legs 130 mm, clearance 105-780mm, weight:130 kgs

Automatic fast chargers: Mains voltage 230 v, output voltage 12 & 24, charging current 30 amps

Angle Polisher: Backing pad 6", orbit: 13/16", power 500 w, rpm 2000-4000,electrical cord -30 ft

3 in 1 Random orbital palm sander: Pad size 6", free speed 12000 rpm, overall length 213 mm, net weight :.65 kgs, spindle thread: 5/16"

Spot Welding Machine (Complete Set): 1. Primary voltage: to be suitable for 415v, 3 phase, 3 wire, 50 HZ, AC supply. 2. Rating @ 50% duty cycle: 200 KVA. 3. Secondary No load voltage ( in stages): 6-12v 4. Max. Welding current: 68KA 5. Secondary short circuit current: 85 KA (VDE 0545) 6. Max. Welding load: 680 KVA 7. Connected load: 520 KVA 8. Electrode pressure: 300 to 2500 KPA> 9. Electrode working range: 250mm 10. Arm spacing: 65/445mm 11. Clamping plates: (above): 400x400mm: (below): 400x400mm 12. Ventilation spacer: Rectangular cross section (2x10). Sq.mm 13. Max.dia of stamping : 1300mm 14. In case of segment dia. Uoto:3000mm 15. Thickness of ventilation stamping: up to 1.0mm. 16. Operating speed: 60 to 90 spots/min

OBD scanner with Bluetooth/Wi-Fi supported should be able to find faults on all Indian Vehicles.Complete with all connectors.

DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGINEERING

PCB Prototype Machine latest Model with PCAM and PCB design software and circuit simulation software.

Soldering & Desoldering stations

Drill Machine used in PCB 230V,1500 RPM which are adjustable in steps, with drill bits 0.8mm -5 nos,1.0mm-5 nos.

PCB designer Kit with content Rotring pens,Marker pens, Magnifing lens,Ruler,Stencils,cutter.Adhesive tape,srubber,cleaning reagent.

PCB curing Machine with Blower ,Heating area 12”*12” with accessories as tray , Brush ,PCB Laminate , Measuring Flask , Clips , Hand Gloves. A nd Chemicals as LPR Photoresist negative ,LPR Thinner , Developer ,Dye Blue ,Developer Part A ,Developer Part B ,Fecl3

Digital Rework Station

Portable Lith Camera for PAB Lab. ( Latest specifications )

Project Board Solder less high quality bread board with tie points 1685 .In built DC +5V/1A & variable DC power supply : 0 to +15V ( 500ma ) and 0 to -15V (500mA)

Programmable Logic controller Micro PLC from delta ,On board NO/NC switches High execution speed, PC based programming ,Soft copy of PLC introduction & Tutorials ,built –in power supplies.

Industrial PLC Micro PLC from Fatek , on board ON/NC switches ,On board IR switches ,Pc based programming ,soft copy of tutorials ,built in power supplies.

CPLD Trainer kit Xilinx chip , usng VHDL software languages.

Microprocessor Training Kits 8085.

Microcontroller Development Board with Programmer .

Photo resist DIP coating Machine

Art work table

Dry Film Laminator

Photo Dye Developer

PCB shearing Machine

UV Exposure Double sided machine

PCB Etching Machine

Monochrome TV Demonstrator Kit

Colour TV Demonstrator Kit

GENERAL WORKSHOP

Lathe Machine With accessories Bed length : about 2 meters Height of centre : about 200-230 mm. Swing over bed: about 415-425mm. Distance between centres: about 1000 mm Bed Type :Standard straight type. Bed width: about 270-275mm. Spindle speeds : 8 Swing over cross slide: about 300mm. Spindle bore: 40 mm. Feed range longitudinal: 40 from 0.64 to 1.98/ revolution. Feed range cross: 0.16 to 1.98mm/revolution. Metric Thread: minimum 20 from 0.5 to 15mm. Motor details: minimum 3hp/ 400v, 3phase. Four position tool post, tool post spanner, centre adaptor, MT-4 dead centre, thread dial indicator, chip tray, tool kit and manual and standard cutting tools. Rear tool post, Machine lamp, quick change tool post, coolant arrangement, chuck guard,3 Jaw true chuck (8”) with C.I. flange, Rear splash guard. Taper turning attachment, Face plate( 350 mm dia) Sheet metal spinning attachment.

Universal milling machine Geared head universal milling machine having longitudinal auto-feed. 1.Surface of table-1120x280mm(Approx.) 2.No.of T-slots-3x15 3.Longitudinal Power & by hand-558mm 4.Cross by hand :200-250 mm 5.Vertical hand :375-415mm 6 Length of Arbor-635mm approx. 7 No. of spindle speed-6 8.Spindle motor-2h.p 9.Feed motor -2h.p 10.Coolant motor-1/10h.p approx. 11.Dividing head and slotting attachment

Radial drilling machine All geared Radial drilling machine Drilling Capacity in M.S-38mm Main drive motor-2H.P Elevating motor-1H.P with accessories

Gear Shaper All geared Shaper machine Length of Ram Stroke - 450mm approx. Working Surface of Table- 450X320mm approx Max. Horizontal Travel of Table - 510mm approx. Max. Vertical Travel of Table - 320mm approx. No. of Ram Speeds - 6 Range of Ram speed(stroke/min.) - 20-90 Main Drive Motor - 3H.P

Universal cylindrical grinder Centre distance-600mm ,Centre height-130mm Wheel head motor-3H.P. Work head Fitting taper-MT3 Work head motor -1h.p

Hydraulic surface grinder Working surface of table-600x200mm Max. Job height admitted-275mm Long traverse of the table-650mm Cross traverse table-Hyd.-225mm Vertical traverse wheel head-400mm Size of grinding wheel-250x19x76 Wheel head motor-2H.p, Hydraulic pump motor-1h.p,Rapid transverse-0.5H.p. to be supplied with Electro mag. Chuck, Coolant pump ,wheel dressing attachment

Tool and Cutter grinder 1. Swing over table-800mm 2.Longitudinal Traverse-250mm 3Cross Traverse-175mm 4.Table size-500X113mm 5.Admit bet centre-300mm 6. Motor-1/2H.p Table swivel clockwise-90deg. Table swivel anticlockwise-45deg. Height of cabnit-5feetto be supplied with indexing head, Universal vise-three way, Tilting table convex movement, Magnetic chuck radius wheel dresser.

Power hacksaw Hydraulic Power hacksaw Capacity of round-200mm Capacity of square-150mm. Size of blade-350-450mm, Motor -1H.p.

Pedestal grinder Double ended pedestal grinder with rough and smooth grinding wheels at each end. Both the wheels are guarded. Wheel size 200mm25mm.Motor-1H.p.

Shearing Machine with Motor, v belt, starter, stroke counter Cutting width 0-300 mm Cutting thickness : up to 1.3 mm Shearing accuracy: 0.1mm Motor power : 2 to 5 hp Shearing capacity: 4 mm

Single Phase A C Welding machine Supply voltage 220-230 Volts, Frequency 50/60 Hz

Gas Welding Machine With Shank Mixer and detachable welding blow pipes complete

MIG Welding Machine Acetylene / Oxygen Cylinders

TIG Welding Machine 3 phase full wave silicon rectifier power source

Seam Welding Machine Vertical TypeCapacity 80 KVA. 220-240V

Iron Jack Planar 8inch and 12 inch size, Cast Iron Body, Carbon Stel Hardened Body

Portable Electrical Planar 240-380 V

Portable Bandsaw 350 watt

Bench Drilling Machine Bosch, 13mm Pilar

Bench Vice 12 inch and 8 inch

Pipie Vice 6 inch and 8 inch

Bar Bending Machine With upper and lower tools

Mini Lase Engraving diykit 50MW

Pellet Press dies 12 MM

MLT 100 Table Saw 255MM, 10 INCH

Dinesh Scientific

LAKSHMI INDUSTRIES (REGD.)

M/s Universal Engineering Equipment Corporation

Mars Edpal Instruments Pvt Ltd