Interior fitout work for at office block and Hostel building in the campus of ICSSR

S. NO. DESCRIPTION OF ITEM UNIT DSR RATE MR RATE Grand Total

material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of

unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts

etc. complete and stacking within 50 metres lead of area 3 sq. metres and below.

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and

1.04 disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar cum 15.9.2 2458.95 20.45 50280.61 0.00

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For

thickness of tiles above 25 mm and up to 40 mm

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40

mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S.

tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a

serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be

1.06 stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required

locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-

charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once

irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction

for scaffolding in the existing item to be done.

Dismantling precast concrete or stone slabs in walls, partition walls etc. including stacking within 50 metres lead :

Thickness up to 40 mm

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the

dumping ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means,

including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge,

beyond 50 m initial lead, for all leads

including all lifts involved.

Grand total 596398.15 0.00

Grand total 596398.15 0.00

2.00 EARTH WORKS

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in

2.01 depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, 2.6

disposed earth to be levelled and neatly dressed.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding

2.02 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. Cum. 2.25 196.00 106.58 20889.09 0.00

Disposal of excavated excess earth away from the site including conveyance of materials up to an average lead of 10 KM

away from the site, and correspondiong required lift, loading, unloading etc complete as directed by the Engineer-in-

charge. (The quantity is net quantity of capacity of truck after deduction of 20% for looseness)(considering the maximum

disposal location at 10 KM distance)

By mechanical transport including loading, unloading and stacking. (Lead upto 10 KM away from the site) Cum. 1.1.2 (13) 326.68 424.18 138570.12 0.00

Digitally signed by AMIT

Supplying and filling in plinth with sand / good soil under floors, including watering, ramming, consolidating and dressing

Anti termite treatment

Providing Pre-constructional anti- termite treatment and creating a chemical barrier to the building by injecting chemical

emulsion of required concentrations under grade slab and Grade beam, all-round the footings, column pits, trenches, pits,

tunnels, wall trenches, back fill, plinth filling, junction of wall and floor, Retaining / side walls of basement floor, external

perimeter of building, surrounding of pipes, expansion joints, below UG sump and Retaining / side walls etc.as per

2.05 instructions of chemical manufacturer and all as directed. The treatment shall be carried out strictly in accordance with the

technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticides

for the treatment shall be Imidacloprid 30.5 percent SC, dilution per litre of water 2.1 ml (1:476) strictly in accordance with

IS 6313 (Part-2): 2022 or as per manufacturers specification whichever is higher. Chemicals Concentration, Imidacloprid

30.5 percent SC 0.075%

Total (Carried Over to Summary of Civil Works) 295952.14 13580.38

3.00 CONCRETE WORKS

Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work;

using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland

Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to

improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing,

3.01 carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-

charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum

specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level :

I Concrete of M10 grade with minimum cement content of 220 kg /cum Cum. 4.20.1.1 8835.15

II Concrete of M15 grade with minimum cement content of 240 kg /cum Cum. 4.20.1.2 8986.15 15.61 140315.36 0.00

Making plinth protection 75mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6graded stone aggregate 20mm

3.02 nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with Sqm 4.17 749.30 33.29 24942.70 0.00

fine sand including finishing the top smooth

Total (Carried Over to Summary of Civil Works) 165258.06 0.00

4.00 REINFORCED CEMENT CONCRETE WORK

4.01 Centering and shuttering including strutting, propping etc. and removal of form for : 5.90

i Foundations, footings, Pedestals, bases of columns, etc. for mass concrete. Sqm 5.9.1 392.15 231.20 90665.08 0.00

ii Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. Sqm 5.9.2 842.50

iii Suspended floors, roofs, landings, balconies and access platform. Sqm 5.9.3 927.25 334.41 310081.67 0.00

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto

Thermo-Mechanically Treated bars of grade Fe-550 D or more. Kg 5.22.6 107.85 17286.25 1864322.06 0.00

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete

above plinth level.

Thermo-Mechanically Treated bars of grade Fe-550 D or more. kg 5.22A.6 107.85 2895.92 312324.43 0.00

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete

work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland

/Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete,

4.04 to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, 5.33

carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the

engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In

case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall

have discretion to either re-design the mix or bear the cost of extra cement

a All works upto plinth level. 5.33.1

ii Concrete of M30 grade with minimum cement content of 350 kg /cum Cum 5.33.1.2 9655.70 129.90 1254275.43 0.00

Digitally signed by AMIT

b All works above plinth level upto floor V level 5.33.2

i Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 5.33.2.1 9860.40 8.39 82728.76 0.00

ii Concrete of M30 grade with minimum cement content of 350 kg /cum Cum 5.33.2.2 10011.35 34.47 345113.76 0.00

Total (Carried Over to Summary of Civil Works) 4259511.19 0.00

5.00 STEEL WORK

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,

5.01 fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped 10.16

washers etc. complete. grade 310 Yst.

Hot finished welded type tubes. Kg 10.16.1 194.40 78279.32 15217499.81 0.00

Total (Carried Over to Summary of Civil Works) 15217499.81 0.00

6.00 WATER PROOFING

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed

with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This

layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This

layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with

polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for

treatment of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound

conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm

height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1

cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-

charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the

6.02 adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. Sqm 22.7.1 1684.60 329.53 555126.24 0.00

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with

water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with

water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth

of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making

pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final

test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average

thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down

6.03 gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep Metre 12.21.1 305.15 182.42 55665.46 0.00

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4

graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement

plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet

TOTAL CIVIL WORK 631235.97 0.00

B ARCHITECTURAL WORK

7.00 BRICKWORKS

Providing and laying autoclaved aerated cement blocks masonry with 100mm/150mm/200mm/230mm/300 mm thick AAC

blocks in super structure above plinth level all floor with RCC band at sill level and lintel level with approved block laying

polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and

reinforcement shall be made for seperately).

Digitally signed by AMIT

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4

(1 cement : 4 coarse sand) .

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth

level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) .

TOTAL OF SUB HEAD NO. 1 1195520.72 0.00

8.00 PCC & PLASTER WORKS

8.01 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) sqm 13.1.1 347.05 843.24 292645.50 0.00

8.02 20 mm cement plaster of mix :1:4 (1 cement : 4 fine sand). sqm 13.3.1 471.35 730.00 344085.69 0.00

8.03 6mm cement plaster on RCC work & ceiling with mix : 1:3 (1 cement : 3 fine sand) sqm 13.16.1 300.45 199.56 59958.40 0.00

8.04 15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand) sqm 13.2.1 399.45

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives

and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on

hacked / uneven background such as bare brick/ block/ RCC work on walls at all floors and locations, finished in smooth

line and level etc. complete.

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top

8.06 layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge. (8.13 bags Cement/100 sqm) Sqm 13.12 537.45 48.68 26162.85 0.00

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the

manufacturers. 12mm cement plaster 1:3 (1 cement :3 sand) = 10 sqm or 1.47 bags of cement used in the mix. Cement

8.07 required for 10 sqm =0.144x510= 73.44kg. Water proofing material required @0. 1 kg per 50 kg of cement = 0.147 kg. 13.21 22.10 18.46 408.02 0.00

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part

TOTAL OF SUB HEAD NO. 2 776468.25 0.00

9.00 WOOD & ALUMINIUM WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in

9.01 position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid cum 9.1.1 142949.70 1.83 261491.81 0.00

for separately). Second class teak wood

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden

9.02 plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone Each 9.53 228.85 120.00 27462.00 0.00

aggregate 20mm nominal size).

Providing and fixing wooden architraves made of Second class teak wood, molded profile, seasoned and well-dried, 20-

9.03 25 mm thick and 50-60 mm wide, fixed to door/window frames with nails or adhesive, with teak wood corners, including Rmt MR 207.53 100.80 0.00 20919.31

necessary finishing melamine polish as per specification.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/ wooden shade texture with

following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to

dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer

and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to

9.04 fill all the small and big holes/ grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing Sqm 13.116 1360.45 70.56 95993.35 0.00

is done this surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in

required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which

is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using

melamine clear polish and melamine thinner mixed in required proportion complete as per direction of

Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Digitally signed by AMIT

FLUSH DOOR SHUTTER : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI

marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters

(over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.5 sqm in all type of flush doors (cost of glass excluded) (overall area

of door shutter to be measured): Rectangular or square

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high

#REF! density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including Sqm 9.127.2 1045.95 150.30 157206.29 0.00

cost of adhesive of approved quality. 1.5 mm thick

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high

#REF! density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including Sqm 9.127.2 897.30 0.00 0.00 0.00

cost of adhesive of approved quality. 1.0 mm thick

Providing & Fixing of S.S Towerbolt 300x12mm including fixtures complete as approved by engineer in charge. (450mm

size for door heights-2.4m)

Providing & Fixing of Rubber buffer 40mmx50mm including fixtures complete as approved by engineer in charge.

#REF! Providing & Fixing of Rubber Door stopper including fixtures complete as approved by engineer in charge. Each MR 110.91 37.00 0.00 4103.79

#REF! Providing & Fixing of Overhead Door Closer including fixtures complete as approved by engineer in charge. Each MR 1167.37 37.00 0.00 43192.76

#REF! Providing & Fixing of Lever Action Flush Bolt including fixtures complete as approved by engineer in charge. Each MR 453.98 37.00 0.00 16797.19

#REF! Providing & Fixing of Floor Bolt Sockets including fixtures complete as approved by engineer in charge. Each MR 233.47 36.00 0.00 8405.08

#REF! Providing & Fixing of Cylinder Locks including fixtures compete as approved by engineer in charge. Each MR 2334.74 37.00 0.00 86385.53

#REF! Providing & Fixing of Lever Action Door Handle including fixtures compete as approved by engineer in charge. Each MR 3242.70 36.00 0.00 116737.20

#REF! Providing & Fixing of Pull Handles & push Plates including fixtures complete as approved by engineer in charge. Each MR 1167.37 37.00 0.00 43192.76

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular

sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with

dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides

with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and

jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass /

stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,

paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of

#REF! fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for kg 21.1.2.1 634.45 585.72 371610.05 0.00

separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber /

neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less

than 10kg/sqm) for ventilaters

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber /

neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than

12.50 kg/sqm) for windows

Digitally signed by AMIT

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber /

neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of

aluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than

20 kg/sqm) for doors

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over

#REF! backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5 mm Mtr 21.8.1 96.75 192.90 18663.08 0.00

depth and 5 mm width

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron

diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with

bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge

#REF! with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U Sqm 9.135.2 1228.00 52.71 64727.88 0.00

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with

minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the

existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to

proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around

the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through

their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets,

side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of

providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength

conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80 mm x 1.25 mm MS laths

with 1.25 mm thick top cover

#REF! Providing and fixing ball bearing for rolling shutters. each 10.7 492.35 2.00 984.70 0.00

#REF! Extra for providing mechanical device chain and crank operation for operating rolling shutters.

i Exceeding 10.00 sqm and upto 16.80 sqm in the area Sqm 10.8.1 1281.35 4.32 5535.43 0.00

ii Exceeding 16.80 sqm in area Sqm 10.8.2 1181.80

Extra for providing grilled rolling shutters manufactured out of 8 mm dia MS bars instead of laths as per design approved

by Engineer-In-Charge ( Area of grill to be measured)

Providing, supplying, installing, testing and commissioning automatic motorized window blinds for windows,

comprising high-quality woven fabric blinds (zebra blackout as specified) manufactured from 100% polyester or

polyester–PVC coated fabric, having UV resistance, colour fastness, flame-retardant properties and anti-fungal treatment,

conforming to IS 2454 (Textile fabrics – colour fastness to light), IS 686 (Methods for determination of flammability of

textiles) and IS 1773 (Colour fastness to washing), with fire performance meeting Class-1 flame spread or equivalent

international standards where applicable. Blinds shall be mounted on extruded aluminium headrail and bottom rail,

corrosion-resistant and powder-coated, complete with tubular motorized mechanism of approved make, suitable for

#REF! continuous operation, incorporating in-built limit switches, thermal overload protection and manual override. System shall sqm MR 15305.54 67.60 0.00 1034654.77

operate on 230V ±10%, 50 Hz AC supply, conforming to IS 732 and IS 694 for electrical wiring, and motors complying

with IS/IEC 60335 safety requirements. Blinds shall be operable through remote control & BMS or home-automation

interface as specified, complete with all wiring, accessories, brackets, couplers, commissioning and adjustments. The

installation shall include measurement, fabrication to exact window sizes, fixing of brackets, alignment, testing and

commissioning, complete in all respects as per approved drawings, manufacturer’s specifications, relevant IS codes and

directions of the Engineer-in-Charge.

Digitally signed by AMIT

GLASS PARTITIONS :-

Glass Partition of 2.5-3.0m high or as per design/drawing FRAMELESS INTERNAL PARTITIONS at all locations with

12mm clear toughened glass or as per elevation drawings with approved make of 316 grade S.S. fittings of approved

makes with FHB-M12 bolts or Equivalent, with PVD Coated G.I. vertical pipes (101.6mm OD) or SS pipes as per design

or as per site condition fixed with S.S. screws or with fixing clips including necessary filling up gaps at junction, at top,

bottom and sides with required weather silicon with backer rod shall be inserted between Aluminiunm channel and glass

as well as both inside and outside around the periphery of the glass to make the glazing water tight and air tight as per

#REF! directions of Engineer-incharge. The S.S. spider fittings shall have to be fixed to G.I. duly PVD coated framework or SS sqm MR 5836.86 14.16 0.00 82649.94

framework including making suitable holes in the glass before tempering process of glass, for installation complete as per

directions of Engineer-in-Charge. The periphery shall have to be sealed both from inside and outside with silicon weather

sealant to make the glazing water and air tight. The sealing of glass to connector pipes with stainless steel fixtures.

Silicon sealant grade shall be approved equivalent as per the design requirement. The partition shall be aligned for the

entire height and for the entire length by laser beam equipment to ensure 100 percent X-axis and Y-axis alignment. The

glass joints must be properly sealed with weather silicon to make the joint water tight and air tight as well. as per

directions of Engineer-In-Charge.

Supply & Installation of glass doors Providing, supplying and fixing of Frameless Single/Double Leaf Swing Glass Door

make in glazing using 12mm thick toughened glass with die cast patch fitting with stainless steel cover including fixing of

patch fittings, floor springs, locks, handles etc. using the hardware items as detailed, complete in all respects as per

detailed drawings, manufacturers specifications and direction of Engineer in charge. Double Leaf Door with Hardware’s

as specified:- Swing Glass Door which includes two no’s each of Top Pivot, Bottom Patch, Top Patch, Floor Lock, Strike

Plate , Floor Spring, or any patch as per site requirement with pair of SS Pull Handle 25 mm dia x 450 mm long and other

accessories for self-closing feature as per detailed drawings.

TOTAL OF SUB HEAD NO 3 1738429.86 1541011.29

10.00 FINISHING WORKS

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer,

over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound )

10.02 content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/ litre. sqm 13.85.3 73.95 2201.33 162788.03 0.00

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre,

10.03 of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and Sqm 13.82.2 137.45 1490.21 204828.70 0.00

colour. Two coats: Two or more coats on new work

Finishing walls with textured exterior/interior paint of required shade :

10.04 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ Sqm 13.45.1 223.60 792.84 177279.02 0.00

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats

Providing and fixing of 12mm thick acoustic panel of approved color & to be fixed with necessary adhesives on existing

partition / wall surfaces as per details , groove as per architectural design and drawing. LOW VOC. Composition : 100%

PET (60% Recycled) with adhesive backing Category : Panels Dimensions : 1220 x 2440mm (+/-2mm) Thickness :

12mm (+/-7%) Sound Absorption : 0.40 NRC (No Air Gap)

Digitally signed by AMIT

Wooden Acoustic Wall Paneling Specification :- Providing and fixing Wall Paneling with Grooved Slats Acoustical High

Density Fiber Board FR Grade Panels 2440x128x16 mm with lineal perforations.The panels shall be one side Pre-

laminated board (decorative lamination on one side and other sides balancing lamination ) grade -1 with 3 mm grooved

at 32 mm pitch, Toungue and Groove edges for seamless mounting having density of 750- 800kg/m3. The back of the

panels are perforated with 10mm diameter circular holes with a nonwoven fabric covering of 0.2mm for providing Sound

absorption .Panel is to be fixed with center & edge clips on CC 18 mm Aluminium section framework with screw fixed on

comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section

(galvanizing @120 grams per sqm ) i.e cross channel of size 80 x 26 x 51 mm (wight approx 480 gm/mtr) are fastened to

10.07 wall positioned vertically in a regular manner at 600mm c/c . Perimeter channel section of size 20x 28 x 30mm fixed to Sqm MR 5400.00 25.40 0.00 137160.00

the all perfarry of using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. The

Polyester wool of 25 mm thickness having density 1000 gsm having flammibality - IS 15061-2002 Annexure clause A

3.2 is then to be inserted in the slots and Cross Channel will come at every 600 centre to centre with centre & edge

bracket in tongue & groove system on Aluminium 18 mm frame. The installed system will have NRC not less than 0.84

as per IS: 8225 / ISO: 354 / ASTM 423. Corner Edges to be sealed with PVC edge bending tape 2.00 mm thick of

approved brand as per manufacturer's specification as per direction of Engineer-in-Charge.

Fabric Wall Panelling Specification Above Wooden Paneling Till Celing LVL :- Providing and fixing of Fire Resistance

Grade Stretch Fabric with the help of PVC Track 25 mm half wrap and mid seam. Magnisite Bonded Wood Wool Panel

having size 1200x600x20 mm panel having fiber width both side is 0.5 - 1 mm with having density 456 kg/m3 . Which will

comprise to NRC Upto 0.90. and meet the stringent fire test required having Class ‘P’ rating for Ignitability test as per BS

476 part 5 and Class ‘1’ rating as per BS 476 part 7 for Surface Spread of Flame test. Class ‘P’ and Class ‘1’ are the

highest rating. BS 476 part 6 Fire Propagation index and for Flaming ISO 1182 and Smoke density as per ASTM E 662

besides base panel conform to EN 13168 2000. Panel is to be installed on comprising of a frame made from especially

fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm ) i.e cross

channel of size 80 x 26 x 51 mm (wight approx 480 gm/mtr) are fastened to wall positioned vertically in a regular manner

10.08 at 600mm c/c . Perimeter channel section of size 20x 28 x 30mm fixed to the all perfarry of using 12mm dia,50mm long Sqm MR 5400.00 23.40 0.00 126360.00

wedge type expanded zinc alloy dash fastner with 10mm bolt. The Polyester wool of 25 mm thickness having density

1000 gsm having flammibality - IS 15061-2002 Annexure clause A 3.2 is then to be inserted in the slots and Cross

Channel will come at every 600 centre to centre. PVC Tracks should be fixed directly by screw to the Magnisite Panel

with Ply Strip 100 x 8 mm and track should be supported from channel.The cavity of tracks filled with 25 mm thk polyester

wadding having density 1000 gsm having flammibality - IS 15061-2002 Annexure clause A 3.2 for better insulation. Then

stretch FR Grade Fabric which will comprises flammability as per FMVSS 302 having to be stretched on these tracks

with 1200mm module or as per the drawing. This system having 0.90 NRC.

Providing & Installing 06 mm thick double-sided High Pressure Interior Compact laminate. These panels, in accordance

with EN 438- Part 6 standards, are meticulously manufactured under high pressure and temperature conditions in a hot

press. The core of the panel consists of premium imported, long fiber virgin kraft papers, combined with specially

formulated double hardened Phenolic resin, and an additional top layer of imported virgin Blue wool scale approved

decorative paper impregnated with Melamine resin. These panels are categorized as flame retardant type class 1 as per

BS: 476 Part 7, ASTM E84, and EN 438- Part 6. Demonstrating exceptional durability, these HPL panels exhibit a tested

10.09 Flexural Modulus of ≥11,000 MPa and Flexural strength of ≥100 MPa. They maintain structural integrity even under Sqm MR 3875.04 21.20 0.00 82150.85

extreme climatic conditions ranging from -20°C to +80°C or in environments with a relative humidity surpassing 85% –

90%. After enduring 3000 hours of artificial weathering, these HPL panels achieve a rating of 5 on the Grey scale and 7/8

on the Blue wool rating.This material possesses antibacterial and anti-fungal properties, Scratch Resistance, and a

density of 1.45gm/cm3. The cladding system will be affixed to aluminum box section 25 x 38 x 1.5mm using Adhesive and

3M tape or Rivets. including 6mm Thick High Pressure laminate Interior Grade with back framing Work including all the

accessories all complete as per the direction of engineer-in-charge.

8 mm thick annealed premium GRIHA rated lacquered glass manufactured industrially by curtain coating process with PU

lacquer (50 micron thick), opaque (if viewed against a support wall) conforming to EN 16477 standards for back painted

glass , of approved color by Architect/ Client fixed with compatible SGG Glassmate Ultrafix or equivalent - Neutral Alkoxy

based Silicone having Shear Bond Strength (Dry, 24 hours), greater than 450 kpa and tack free time of 10 to 30 mins

10.10 compatible for installation of mirror and lacquered glass / SGG Glassmate Mirror mounting tape MIRROR MOUNTING Sqm MR 7000.00 48.38 0.00 338660.00

TAPE or equivalent - Foam based double sided adhesive tape for instantaneous adhesion, compatible with mirror and

lacquered glass having Shear bond strength (Dry, 15 mins) of 250 to 350 kpa) on a perfectly leveled 12mm thick water

proof marine plywood which is mounted on the RCC wall/any other.

Digitally signed by AMIT

Supply and installation of Interior wall panels, manufactured from polystyrene using a unique hot stamping process that

provides enhanced scratch resistance, stain resistance, water resistance, termite resistance, anti-static properties. The

panels are available in multiple designs, offering high durability and recyclability, They are VOC-free (PN-EN 16516:2017-

11) and have a tested tensile strength of 8.10 MPa as per ISO 527 (Part 2):2012. Each panel is dimensioned at 12 & 21

mm thickness, with a visible width of 115 mm and a length of 3050 mm, covering approximately 3.77 sq. ft. per panel.

Panels are supplied with compatible accessories, including universal (U) trims, right (R) trims, and left (L) trims,

10.11 depending on the panel line type. All products are backed by a 2-year manufacturer's warranty. The installation of Sqm MR 4734.40 109.91 0.00 520372.11

polystrene interior panels shall be carried out using the adhesive method. It is recommended to use a one-component

polymer hybrid adhesive that is free from solvents and isocyanates. The adhesive nozzle should be notched at a 45-

degree angle, and the adhesive should be applied with a bead size of 6x3 mm. Apply the adhesive vertically on the back

of the panels and trims at the points where they will adhere to the wall surface. Panels can be easily cut to the desired

size using a handsaw or jigsaw. All installation work shall comply with local building codes to ensure long-term durability,

safety, and optimal performance.

Providing and fixing 4 mm thick waterproof plywood (or equivalent) for paneling work, complete with all necessary frame

supports, beading, and edge finishing.Includes cutting to required sizes, surface preparation, adhesive application,

mechanical fixing with screws/nails, gap filling, and protective coating as per design requirements.All complete in all

respects as per specifications and direction of Engineer-in-Charge (EIC).

Providing and fixing PVC skirting board comprising a foamed inner core and a hard outer layer. Installation shall be

carried out using a suitable polymer-based adhesive to achieve a seamless finish against the wall and floor surfaces. The

10.13 system shall include necessary end caps installed as a flush finish. The skirting board shall be impact-resistant and Mtr MR 820.21 134.64 0.00 110433.07

moisture-resistant. All works shall be executed complete as per the direction of the engineer-in-charge

Providing and fixing frosted translucent cast PVC self-adhesive vinyl film (or equivalent) with special CRYSTAL-effect

finish to replicate sand-blasted appearance on glass surfaces, featuring customized designs for privacy and aesthetic

enhancement.Film specifications: 2 mil (0.05 mm) thickness without adhesive / 8 mil (0.8 mm) with adhesive, minimum

10.14 tensile strength 3.5 lb/inch (0.6 kg/cm at 23°C), adhesion after 24 hours ≥4 lb/inch (0.7 kg/cm) on glass, acrylic, and Sqm MR 1725.00 13.62 0.00 23487.60

polycarbonate substrates.Includes surface preparation, precise cutting/application of custom graphics, bubble-free

installation, edge sealing, and protective measures during curing period.All complete in all respects as per specifications,

approved designs, and direction of Engineer-in-Charge (EIC).

Providing and fixing entry & exit gate GRC (Glassfibre Reinforced Cement) work , including GRC columns, jali screens,

mouldings, vertical panels, and associated architectural elements complete with all labour and accessories required for

10.15 proper fitting and installation.Includes surface preparation, anchoring systems, jointing compounds, sealing, protective Sqm MR 10398.30 309.20 0.00 3215152.28

coatings, and finishing as per approved design and structural requirements.All complete in all respects as per

specifications, drawings, and direction of Engineer-in-Charge (EIC).

TOTAL OF SUB HEAD NO. 4 892200.70 5370495.68

11.00 FALSE CEILING WORKS

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to

centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of

cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of

angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5

mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting

clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick

11.01 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl

plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling

section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable

for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and

direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS

Certification marks)

Digitally signed by AMIT

ii 12.5 mm thick tapered edge gypsum moisture resistant board Sqm 12.45.3 1529.10 372.83 570101.54 0.00

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and

pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥ 85%, Thermal Conductivity k =

0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizont al level suspended on interlocking T-Grid

of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of

15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size

15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel

item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger

11.02 rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along Sqm 26.27.2 2671.20 4.99 13339.97 0.00

main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000

mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40

mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be

pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and

as per directions of the engineer-in-charge. With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)

Providing and fixing false ceiling at all heights including providing and fixing of framework made of special sections,

power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both sides inclusive) as per IS: 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, fixed at 1200 mm

centre to centre, one flange fixed to the ceiling with dash fasteners 12.5 mm dia x 50 mm long with 6 mm dia bolts, the

other flange of cleat fixed to angle hangers of size 25 x 10 x 0.50 mm of required length with nuts and bolts of required

size, and the other end of angle hanger fixed to intermediate G.I. channels of size 45 x 15 x 0.9 mm running at 1200 mm

centre to centre, to which ceiling sections 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each

having lips of 10.5 mm shall be fixed at 450 mm centre to centre in a direction perpendicular to the G.I. intermediate

channels, with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

11.03 perimeter channels 0.5 mm thick, 27 mm high having flanges of 20 mm and 30 mm long, perimeter fixed to wall/partition Sqm MR 2400.00 117.12 0.00 281088.00

with rawl plugs at 450 mm centre to centre and 25 mm long dry wall screws at 230 mm interval, including providing and

fixing cement fibre board of approved make and thickness (minimum 8–10 mm or as specified) to ceiling sections and

perimeter channels using corrosion-resistant self-drilling screws at 230 mm centre to centre, including jointing and

finishing with manufacturer-recommended jointing compound, alkali-resistant jointing tape, finishing in required number of

layers to achieve a smooth and flush finish, including application of primer suitable for cement boards, and including cost

of making openings for light fittings, grills, diffusers and other cut-outs with proper framing using perimeter channels, all

complete as per drawings, specifications and directions of the Engineer-in-Charge, but excluding the cost of painting.

Supply and installation of UPVC interior panels utilizing thermal digital printing technology, offering impact resistance as

per EN 477:2018 (passed with no cracks), and flexural strength of 55.62 MPa, tested in accordance with ISO 178:2019

Method A, Panels are UV-stable, weather-resistant, and feature thermal digital printed non-repetitive surface finishes.

They conform to EN 13501-1 fire classification standards (Class D-s3, d0), are VOC-free, 100% recyclable, and

dimensioned 1mm thick at 250mm visible width, with lengths of 2950 mm covering 7. 93sq.ft per panel respectively.

Supplied with compatible accessories including ‘J’ trims ‘T’ trims and A special drip trim is used to ensure that water

drains out efficiently, preventing moisture accumulation and extending the lifespan of the installation backed by a 10-year

warranty. Installation shall be carried out using interior panels comprising four lamellae, featuring four grooves with an

interlocking click system, a hurricane-resistant locking mechanism, and a rear-ventilated system to enhance air

circulation. The panels shall be fixed over a 0.55 mm thick CR-1 grade galvanized iron (GI) channel system. The wall

11.04 angle shall be 0.55 mm thick (minimum) with two flanges measuring 10 mm and 25 mm, fixed at 1000 mm centers. The Sqm MR 3647.64 75.55 0.00 275564.61

main frame shall be 0.80 mm thick (minimum), 45 mm wide, with two flanges of 15 mm each, also placed at 1000 mm

centers. The cross frame shall be 0.55 mm thick (minimum), 80 mm wide, with two flanges of 26 mm each, installed at

450 mm centers. A perimeter channel of 0.55 mm thickness and 27 mm width, with flanges of 20 mm and 30 mm, shall be

fixed continuously along the corners of the ceiling. The wall angle shall be suspended up to 600mm from the true ceiling,

after which the main frame will be fixed to the wall angle using 3x19 mm metallic screws, and the cross frame will be fixed

onto the main frame. Interior panels shall be secured onto the GI frame using pan head screws (3x13 mm) through the

designated slots. The minimum drop from the true ceiling shall be 45 mm. All installation work shall be executed in a

stress-free manner and in full compliance with local building codes to ensure long-term durability, safety, and optimal

Digitally signed by AMIT

Supply and installation of Interior wall panels, manufactured from polystyrene using a unique hot stamping process that

provides enhanced scratch resistance, stain resistance, water resistance, termite resistance, anti-static properties. The

panels are available in multiple designs, offering high durability and recyclability, They are VOC-free (PN-EN 16516:2017-

11) and have a tested tensile strength of 8.10 MPa as per ISO 527 (Part 2):2012. Each panel is dimensioned at 12 & 21

mm thickness, with a visible width of 115 mm and a length of 3050 mm, covering approximately 3.77 sq. ft. per panel.

Panels are supplied with compatible accessories, including universal (U) trims, right (R) trims, and left (L) trims,

11.05 depending on the panel line type. All products are backed by a 2-year manufacturer's warranty. The installation of Sqm MR 4734.40 11.52 0.00 54540.29

polystrene interior panels shall be carried out using the adhesive method. It is recommended to use a one-component

polymer hybrid adhesive that is free from solvents and isocyanates. The adhesive nozzle should be notched at a 45-

degree angle, and the adhesive should be applied with a bead size of 6x3 mm. Apply the adhesive vertically on the back

of the panels and trims at the points where they will adhere to the wall surface. Panels can be easily cut to the desired

size using a handsaw or jigsaw. All installation work shall comply with local building codes to ensure long-term durability,

safety, and optimal performance.

Supply and installation of UPVC interior panels utilizing thermal digital printing technology, offering impact resistance as

per EN 477:2018 (passed with no cracks), and flexural strength of 55.62 MPa, tested in accordance with ISO 178:2019

Method A, Panels are UV-stable, weather-resistant, and feature thermal digital printed non-repetitive surface finishes.

They conform to EN 13501-1 fire classification standards (Class D-s3, d0), are VOC-free, 100% recyclable, and

dimensioned 1mm thick at 250mm visible width, with lengths of 2950 mm covering 7. 93sq.ft per panel respectively.

Supplied with compatible accessories including ‘J’ trims ‘T’ trims and A special drip trim is used to ensure that water

drains out efficiently, preventing moisture accumulation and extending the lifespan of the installation backed by a 10-year

TOTAL OF SUB HEAD NO. 5 583441.51 796930.82

12.00 FLOORING WORKS

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen

platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture

laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with

matching pigment, epoxy touchups, including rubbing, curing, moulding and polishing to edges to give high gloss finish

etc. complete at all levels. Granite of any colour and shade (Area of slab over 0.50 sqm.)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give

high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm

with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter

12.04 and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, each 8.5 978.70 10.00 9787.00 0.00

rubbing and polishing of cut edges etc. complete.

For Door / Window sill & Soffits:- Providing and fixing 18-20 mm thick gang saw cut Granite, mirror polished,

premoulded and prepolished, machine cut for window sills, similar locations of required size, approved shade, colour and

12.05 texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed Sqm MR 3761.53 5.85 0.00 22004.96

with matching pigment, epoxy touchups, including rubbing, curing, moulding and polishing to edges to give high gloss

finish etc. complete at all levels.

DOUBLE CHARGE TILE

Providing and laying double charge Vitrified tiles in floor, skirting & dado with given sizes, with water absorption less

than 0.08% and conforming to IS:15622,of approved brand & manufacturer, in all colours and shade, laid with 32 mm(

average) cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting

12.06 the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . 11.41A

Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber

mallet for placing the tiles gently and easily, including grouting of joints with non shrink epoxy grout in matching shade

and colour. Grooves shall be provided using plastic spacers as per approved design and drawing.

a Double charge vitrified tile polished finish of size 11.41A.1

c Glazed Vitrified tiles Matt/Antiskid finish of size 11.41A.3

Digitally signed by AMIT

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less

than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12

mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

grouting the joint with white cement & matching pigments etc. complete.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78,

solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick

12.08 cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & Sqm 12.55 1703.95 261.35 445327.33 0.00

marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing

skirting upto 150 mm height along the parapet walls in the same manner.

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener

12.09 consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening Sqm 11.4 978.45 66.56 65125.63 0.00

compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement

slurry, but excluding the cost of nosing of steps etc. complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as

curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm

12.10 (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing Sqm 11.55.1 3186.70 13.08 41667.86 0.00

with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all

complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry

Red, Elite Brown, Cat Eye or equivalent.

Granite work gang saw cut (polished and machine cut) of thickness 18-20 mm for wall lining (veneer work), backing

filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white Derived form

cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the granite shade (To be DAR 8.1.1.2

secured to the backing by means of cramps, which shall be paid for separately).

Supply and Installation of SPC Flooring which is engineered for exceptional performance and long-term durability. It

features a total thickness of 4+1 mm (Herringbone Pattern), including an integrated IXPE underlay that provides superior

sound absorption and enhanced walking comfort. The flooring offers excellent dimensional stability (≤ 0.17%) and

minimal curling (≤ 2 mm). With a wear layer thickness of no less than +0.3 mm and a density range of 1.98–2.05 g/cc, it

12.12 ensures outstanding strength, resilience, and surface integrity. The precision locking system provides a locking strength Sqm MR 3699.87 179.86 0.00 665465.81

of ≥ 2.5 Kn/M, ensuring excellent joint integrity and long-lasting performance. The surface delivers AC6 wear resistance

and a refined gloss level of 5–8 GU. The flooring also demonstrates high peel strength (≥ 90 N) and meets Bfl-S1 fire-

resistance standards, ensuring safety, durability, and reliability under demanding conditions.

Providing and laying Digital Placement of Color / 100% Solution Dyed Nylon 6 carpet tiles (anti static ) Tufted level Loop

Pile tiles shade and pattern as approved make & size 500 x 500 mm, with secondary backing back 2 back modified

bitumen and with protective stain treatment(s), soil protection to repel and resist Stain and Anti Microbial treatment,

12.13 Appearance Retention Rating (CRI 101) for severe use with PVC free backing having min. face weight of 600 gram/m2. Sqm MR 1880.77 214.06 0.00 402596.77

Flooring Radiant Panel Class I grade including fixing with Volatile Organic Compound (VOC) Free Adhesive etc.

complete as per drawing and directions of Engineer-In- Charge. Carpet should have at least 15 years of warranty. Fixing

will be done by Trained team only.

TOTAL OF SUB HEAD NO. 6 1826996.37 1090067.54

13.00 ROOFING & FAÇADE WORKS

Digitally signed by AMIT

16mm Multicellular Polycarbonate Sheet Supply and Installation of Flux polycarbonate multi-layered, Multi-cell

Connectible modular panel system for, a complete assembly of co-extruded UV protected polycarbonate panels

incorporated into a complete system.

a) Standing seam polycarbonate panel system of minimum 16 mm thick panels with bigger width will be preferred for

reducing number of joints in the roof.

b) Panels shall be with grip lock double tooth locking mechanism with interlocking connectible connectors running

lengthwise at both sides of the panel. Panels shall be fixed on Purlins of MS structure with 3 numbers of self-drilling

screws to ensure a pull-out load of min. 7000 N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005.

c) The minimum width of the panel system shall be 1200 mm.

d) Panels shall be solo opaque type in opaque and translucent clear combination with seven layers for required lux level

along with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance.

13.01 e) Panels shall have transparent body and opaque layers in between to achieve angular daylighting effect to avoid Sqm MR 4669.49 5.76 0.00 26896.25

sunlight and heat.

f) Panels with minimum seven layers will be preferred for better insulation and improved shading coefficient.

g) Cost to include all accessories including aluminum profiles with EPDM Gaskets, at alternate edges with taper cutting to

achieve the required profile, aesthetics and performance criteria’s. U value shall not be more than 1.9 Watt/m2K as per

EN ISO 1077-2:2018 and respective third Party test certificate shall be produced before procurement.

h) Panels shall have an X cell structure also called truss bracing design to have more strength and flexibility

simultaneously.

i) Panels must satisfy Dart drop impact test as per IS 14443-97, shall show no sign of breakage on Polycarbonate sheets

which have been exposed to UV for a min. of 500 Hours as per ASTM G 155.

j) Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for

500 Hours as per ASTM G 155.

Providing, supplying, and fixing cladding with Bison cement fibre boards of approved make and specified thickness,

fixed over aluminium framework comprising aluminium sections of approved size, gauge and spacing, fabricated and

installed as per approved design, drawings and shop drawings, including cutting, drilling, jointing and fixing the boards to

the aluminium framework with approved self-drilling screws, fasteners, cleats, brackets and accessories; including

13.02 provision of control joints, sealing of joints where specified, proper alignment, levelling, edge finishing, protection of Sqm MR 3112.99 125.76 0.00 391489.87

finished surfaces, scaffolding, handling and transportation, complete in all respects and to the satisfaction of the Engineer-

in-Charge. All works shall be executed in accordance with IS 14862 and ASTM C1186 for fibre cement boards, IS 733 /

IS 737 for aluminium sections, and the manufacturer’s specifications and recommendations.

14.00 ARCHITECTURAL STEEL WORKS

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding,

grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel

nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel

bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of

Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners etc.).

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming

14.02 coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, Kg 10.25.2 172.60 232.80 40181.28 0.00

brackets, gates and similar works.

Signage: Providing and fixing complete signage system (or equivalent) dentification, comprising sign box, support

structure, and illumination as per design requirements.

Sign Box: Entire sign face (all 4 sides) fabricated from 4.5 mm thick white translucent 040 acrylic sheet with backlighting;

plotter-cut Pantone Yellow C vinyl graphics and Pantone Black 6C blockout vinyl text pasted over acrylic face with white

diffuser film on inside surface.

Sign Box Frame: 3 mm thick aluminium fabrication, PU painted RAL 9011 black, mounted on sign structure with provision

14.03 for concealed wiring/cable entry and telephone connection niche. Each MR 168750.00 2.00 0.00 337500.00

Bottom Panel: MS panel PU painted to match Pantone Black 6C vinyl finish.

Sign Structure: MS hollow box section 300x300 mm for structural stability; contractor responsible for complete structural

design, analysis, and certification ensuring wind load resistance and safety.

Lighting: Internal illumination using power LED lights with electronic controllers for uniform backlighting.

All complete with assembly, alignment, electrical connections, testing, structural certification, and protection as per

specifications, drawings, and direction of Engineer-in-Charge (EIC).

TOTAL OF SUB HEAD NO. 8 74939.28 337500.00

Digitally signed by AMIT

Project Name:- Renovation/ Restoration and addition/ Alteration Interior/ Modernization of existing buildings/ facilities of ICSSR

Name of Work : Plumbing BOQ as per DSR 2023

Description Unit DSR No. DSR Rate MR Rate QtY DSR Amount MR Amount

SUBHEAD-I : SANITARY Fixtures and Fittings

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level

white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with

all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid Each 17.2.1 6515.55 5.00 32577.75 0.00

Providing and fixing wash basin with C.I.brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern,

including painting of fittings and brackets, cutting and making good the walls where required :

ii White Vitreous China Flat back wash basin size 450 x 300 mm with single 15mm C.P. brass pillar tap Each 17.7.7 1513.60 5.00 7568.00 0.00

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of

approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm Each 17.32.2 1361.80 5.00 6809.00 0.00

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than

Providing and fixing CP Brass 32 mm size bottle trap of approved quality and make as per direction of engineer in charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge .

2.05 Providing and fixing CP Brass Shower rose with 15 or 20 mm Inlet 18.22

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40

2.06 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10

ii Kitchen sink without drain board 610x510 mm bowl depth 200 mm Each 17.10.2.1 4940.80 4.00 19763.20 0.00

2.07 Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete. Flexible Pipe 17.28

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x 260x350 mm and

340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with

brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and

floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing cistern Each 17.4.1 6358.75 1.00 6358.75 0.00

Providing & fixing stone slab table rubbed, edges rounded and polished of size 75 X 50cm deep and 1.8 cm thick fixed in urinal

patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with

cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size) as per Engineer-in-charge

and finished smooth

White Agaria Marble Stone Sqm 8.10.1 3500.45 1.00 3500.45 0.00

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard

2.10 shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms. Each 17.71 168.35 5.00 841.75 0.00

Digitally signed by AMIT

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall

2.11 face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms Each 17.72 231.95 5.00 1159.75 0.00

2.12 Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 18.49

2.13 Providing and fixing C.P. brass angle valve for basin mixer etc. of approved quality conforming to IS 8931. 18.53

2.14 Providing & fixing diverter Each MR 1940.43 4.00 0.00 7761.72

Providing and fixing stainless steel floor drain trap of approved make with grated cover, conforming to IS 2556), including

necessary height adjustment ferrule, rubber seal.

Providing and fixing toilet paper holder of approved make and quality stainless steel SS-304, heavy duty, size 150x100mm with

concealed fixing, conforming to IS 2556), including all necessary screws, rawl plugs, and wall anchors for flush mounting at

2.16 900mm height from finished floor level, complete with testing for stability and smooth operation, making good the surface to Each MR 1543.53 5.00 0.00 7717.63

match existing finish, and 2-year warranty against corrosion/manufacturing defects; rate per Each/No., inclusive of labour,

materials, GST, and all leads/lifts.

Provinding and fixing automatic soap dispencer as per specification all complete as per the direction of engineer incharge.

2.18 Provinding and fixing hand dryer as per specification all complete as per the direction of engineer incharge. Each MR 20825.92 0.00 0.00 0.00

SUBHEAD-I(B): SANITARY FIXTURES AND FITTINGS INSTALLATIONS (As Per Market Rates)

Providing and fixing C.P. brass health faucet with 8mm dia 1m long PVC tube and wall hook complete in all respects. all

complete as directed by Engineer-in-charge.

2.20 Office Toilet Sanitary Fixtuers Lot MR 98264.06 1.00 0.00 98264.06

INTERNAL DRAINAGE INSTALLATIONS

Providing and fixing cast iron trap of self cleansing design with cast iron screwed down or hinged grating with or without vent

arm complete, including cost of cutting and making good the walls and floors.

i 100 mm inlet and 100 mm outlet Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905 Each 17.60.1.3 854.55 13.00 11109.15 0.00

ii 100 mm inlet and 75 mm outlet Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905 Each 17.60.2.3 591.40 5.00 2957.00 0.00

Making khurras 45x45 cm with average minimum

thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm

nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand)

and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing

2.23 with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, 12.41

(i) Single socketed pipes. 110 mm diameter Meter 12.41.2 377.40 90.00 33966.00 0.00

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water

2.24 pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal 12.42

ii Single tee with door 110x110x110 mm Each 12.42.3.2 234.15 11.00 2575.65 0.00

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of

2.25 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement 12.43

mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Digitally signed by AMIT

2.26 Providing and fixing soil, waste pipes Centrifugally cast (spun) iron S&S pipe 17.35

Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905 metre 17.35.1.3 1169.30 112.00 130961.60 0.00

Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement

2.27 concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) 17.37

including cost of cutting holes and making good the walls etc.

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.

100mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 17.38.1.3 567.20 10.00 5672.00 0.00

2.29 Providing and fixing plain bend of required degree. 17.39

100mm dia Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 17.39.1.3 368.00 10.00 3680.00 0.00

2.30 Providing and fixing double equal plain junction of required degree. 17.42

100x100x100x100 mm Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905 Each 17.42.1.3 760.70 10.00 7607.00 0.00

2.31 Providing and fixing single equal plain junction of required degree : 17.44

100X100X100mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 17.44.1.3 581.45 10.00 5814.50 0.00

2.32 Providing and fixing single unequal plain junction of required degree 17.48

100x 100x75 mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 17.48.1.3 551.55 10.00 5515.50 0.00

2.33 Providing and fixing Hubless cast iron offsets epoxy coated inside & outside as per IS : 15905 17.54.A

2.34 Providing and fixing terminal guard: 17.56

100mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 Each 17.56.1.3 427.80 10.00 4278.00 0.00

2.35 Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe 17.57A

100mm SS 304 grade coupling with EPDM rubber gasket Each 17.57A.1.1 432.05 9.00 3888.45 0.00

2.36 Providing and fixing PTMT grating of approved quality and colour 18.58

Circular type 125 mm nominal dia Each 18.58.1.2 51.85 18.00 933.30 0.00

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size)

alround CI HUBLESS including bed concrete as per standard design

Note: This work shall be done all-round PIPE AT ground floor's toilet. 100mm diameter metre 19.2.1 964.75 62.00 59814.50 0.00

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal

work) exposed on wall.

i 32 mm nominal outer dia pipes Rm 18.7.4 518.75

ii 40 mm nominal outer dia pipes Rm 18.7.5 702.95 30.00 21088.50 0.00

ii 50 mm nominal outer dia pipes Rm 18.7.6 934.15 17.00 15880.55 0.00

2.39 Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality 18.4

i 32 mm nominal outer dia pipes Rm 18.40.4 22.20

ii 40 mm nominal outer dia pipes Rm 18.40.5 25.25 30.00 757.50 0.00

iii 50 mm nominal outer dia pipes Rm 18.40.6 30.50 17.00 518.50 0.00

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

H D - 20 Circular shape 560 mm internal diameter Each 19.19.3.1 1675.70 2.00 3351.40 0.00

WATER SUPPLY INSTALLATIONS

2.42 Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design. Each 17.3 55.65 6.00 333.90 0.00

Digitally signed by AMIT

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass

threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one

step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall

i 15 mm nominal outer dia pipes Rm 18.7.1 286.80 15.00 4302.00 0.00

ii 20 mm nominal outer dia pipes Rm 18.7.2 335.00 45.00 15075.00 0.00

iii 25 mm nominal outer dia pipes Rm 18.7.3 401.55 12.00 4818.60 0.00

iv 32 mm nominal outer dia pipes Rm 18.7.4 518.75 4.00 2075.00 0.00

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass

threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one

2.44 step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete 18.8

as per the direction of engineer incharge. Concealed work including cutting chases and making good the wall etc.

i 15 mm nominal outer dia pipes Rm 18.8.1 497.80 35.00 17423.00 0.00

ii 20 mm nominal outer dia pipes Rm 18.8.2 537.60 65.00 34944.00 0.00

iii 25 mm nominal outer dia pipes Rm 18.8.3 627.25 14.00 8781.50 0.00

iv 32 mm nominal outer dia pipes Rm 18.8.4 739.30 25.00 18482.50 0.00

2.45 Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) 18.17

i 25mm dia, nominal bore Each 18.17.1 622.40 4.00 2489.60 0.00

ii 20mm dia, nominal bore Each 18.17.1A 539.95 12.00 6479.40 0.00

iii 32 mm dia, nominal bore Each 18.17.2 689.60 2.00 1379.20 0.00

Structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and

applying a priming coat of approved steel primer all complete.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable

2.47 locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support per litre 18.48 11.00 2000.00 22000.00 0.00

Constructing masonry Chamber 60X60X75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4

coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside)

with channel lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size)

2.48 necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and 18.33

inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement

complete as per standard design:

Grand total 639742.10 129181.53

Grand total 639742.10 129181.53

Digitally signed by AMIT

Project Name:- Renovation/ Restoration and addition/ Alteration Interior/ Modernization of existing buildings/ facilities of ICSSR

S.No. Item Description of item Unit Rate Amount

Supplying, Installation, Testing and Commissioning of Fully Digital IP Based Conference systems Controller Audio

processing device responsible for routing, controlling and processing the audio with built in (or using external

OEM certified DSP / product of approved make) intelligent adaptive acoustic feedback suppressor, echo

cancellation, minimum 5 or more band parametric equalizers for optimal speech intelligibility as required, support

loop-through connection with cable redundancy, Ethernet led’s for each socket for netowrk indications,

Independent powered sockets; Supports hot plug and play system ,Power consumption 530 W or less, 4 Nos.

ethernet Port each capabale of delivering loop through power to the delegate and chairman units which supports

IP connections with minimum total power supply of 430 W by the processing device for delegate and chairman

units. Independent powered sockets, short circuit on one socket does no influence the other sockets.The device

shall have two audio input for inserting external analogue audio signal into the system, and mix-minus for

IP based Control connecting the conference system to video conferencing equipment and shall have two audio outputs for mix-

Unit minus and to connect an external sound reinforcement system. shoumd have 4 nos. audio line outputs. The

Ethernet Port should support industry standard audio protocols like Dante, AES67 or OMNEO etc.and Ethernet

(IEEE802.3) standards. Frequency response 30 Hz – 20 kHz; THD at nominal level < 0.1 %; Dynamic range: > 95

dB; Signal–to-noise ratio > 95 dB;

Supply, installation, testing & commissioning of 19" rack mountable IP based conference management system

with Conference server & Server- Client software for Conference systems management, camera control and

Microphone Management software. Microphone management facility : which shall facilitate management of

delegate request list switching ON and OFF of individual microphones from single / multiple points ; Setting and

control of the volume levels of individual microphones and loudspeakers in the delegate / chairman units. Camera

shall automatically focus the delegate speaking ; Software interface shall also provide meeting data such as

current speakers ; request lists. Server/controller should be with Pre-installed and configured Operating system

IP based Windows Server 2019; Windows Server 2022 or latest as per OEM recommendation. Ethernet type 1000BASE-T,

2 Conference CPU passmark >= 6000, RAM: 8 GB, Free disk space: 20 GB, Ethernet card: 1 GB, Along with software for Client 2 No. 873,843.75 1,747,687.50

System Server software for IP based digital Conference systems management, for synoptic microphone control via a virtual

mimic of room layout,where microphones can be controlled in real time. It should dante/AES67 supported to

interconnect with Room audio. Should be supplied with Keyboard mouse and monitor complete as per

Digitally signed by AMIT

Supplying, Installation, Testing and Commissioning of Fully Digital IP Based power extension device for

additional power extension for table microphones interfaces. Should be used in combination with a central

device to supply extra power to the network -The built-in 4 port Ethernet switch shall connect all devices in the

system together in a network with with minimum total power supply of 430 W by the processing device for

IP based power delegate and chairman units. The powering device shall have no user controls and shall be controlled remotely.

expender Should support all types of topology : loop in loop out, closed loop connectivity with cable redundancy and star

connection (direct connection to a PoE switch) as per the site requirement. - Zero configuration and Fully

compatible to the Ethernet (IEEE802.3) and should support industry standard audio protocols like Dante/ AES etc

through Conference network of OEM. Proprietary protocols will not be accepted. Standby mode and less power

consumption to be environment friendly: Power consumption- max 550 W.

Supply , Installation, Testing & Commissioning of Modular screwless Digital IP based Flush Mount Chairman Unit.

The Unit shall be flushed mounted on the table and shall have Microphone socket with a long stem pluggable

gooseneck Microphone of 480mm, request switch, Priority Button for temporarily muting delegates and flush

mount loudspeaker panel, Maximum acoustic output level (dB SPL): 87 dB SPL, The loudspeaker and the

microphone of the same unit can be active simultaneously giving a real time face to face meeting experience. It

shall provide digital signal processing and transmission of all audio signals via an IP network, and shall have

low susceptibility to mobile phone interference. All the modules shall be pluggable type, and connected to an IP

IP based Flush based flush base interface unit. Provision shall be made so the unit can be click-to-fit mounted in combination

4 Mount Chairman with couplings and end caps in wooden surface.The unit should have a modular deisgn allowing flexibility to 5 No. 131,801.26 659,006.28

Unit mount devices like microphone,press to talk button at different mounting locations on the table.The unit should

be with following feature- Microphone on/off button with LED indicators showing - Red Microphone on indicator

(active mic)- Green request indicator (request-to-speak accepted, in waiting).

Supply , Installation, Testing & Commissioning of Modular Digital IP based Flush Mount Delegate Unit. The Unit

shall be flushed mounted on the table and shall have Microphone socket with a long stem pluggable gooseneck

Microphone of 480mm, request switch and flush mount loudspeaker panel, Maximum acoustic output level

(dB SPL): 87 dB SPL, The loudspeaker and the microphone of the same unit can be active simultaneously

giving a real time face to face meeting experience. It shall provide digital signal processing and transmission of all

audio signals via an IP network, and shall have low susceptibility to mobile phone interference. All the modules

shall be pluggable type, and connected to an IP based flush base interface unit. Provision shall be made so the

IP based Flush unit can be click-to-fit mounted in combination with couplings and end caps in wooden surface.The unit

5 Mount Delegate

should have a modular deisgn allowing flexibility to mount devices like microphone,press to talk button at 48 No. 89,894.40 4,314,931.19

different mounting locations on the table.The unit should be with following feature- Microphone on/off button

with LED indicators showing - Red Microphone on indicator (active mic)- Green request indicator (request-to-

speak accepted, in waiting).

Digitally signed by AMIT

Supply, installation, testing & commissioning of IP based Under table Digital Interface Unit for connecting

minimum two delegate as per site requirement. Interface Unit shall be surface mounted type for easy mounting

under the table. It should have the provision to connect two microphone sockets, two press to talk buttons and

two language selection panels. It shall be IP based and fully Digital Type for routing of audio and control signal in

Digital Interface digital domain only.It shall have provision for connecting external speaker/ microphone. Shall support all types of

6 Unit for Conference topology : loop in loop out, closed loop connectivity with cable redundancy and star connection (direct 29 No. 105,346.70 3,055,054.19

system connection to a PoE switch). Should support industry standard audio protocols like Dante/ AES etc. Proprietary

protocols will not be accepted.

Supply and laying of 250 meter network cable with connectors of same OEM which shall be used to connect a

conference device to the audio powering switch or to the powering switch. It provides network communication

and power transports in one cable. The system network cables are used when loop-trough and redundant cable

connections are required. Dimensions (dia.) 6.40 mm or less, Color Traffic black RAL 9017,Bending radius 35 mm

Conference cables and Material: NHFR (No Halogen Flame Retardant). The System Network Cables have to terminated at both ends

& Connectors with required RJ45 like connectors with additional power pins and has to be supply as per site requirement.

Conference system, cable & Connectors should be from single manufecturer.

Supply, installation, testing & commissioning of 6-8" Two way Coxial ceiling speaker with 30 Watts Rated Power

or better, 45W Max Power or better, Transformer taps: 30 W ,15 W ,7.5 W; Frequency Range (-10 dB) 70 Hz - 20

Khz or better , Opening Angle 173˚ ; Sound pressure level: 89 dB or better, 6" Driver size, Tweeter: 0.5", Should

8 Ceiling Speakers 22 Nos. 5,477.55 120,506.20

have Support EN-60065 Safety.

Supplying, Installation, testing and commissioning of passive column loudspeakers with continuous Power

handling :300 W ro more; program Power handling 600 W or more; Frequency range : 50 Hz – 16,000 Hz or

better; sensitivity :91.5 dB ; Coverage angle HxV : 180° x 25°; Nominal impedance : 8 Ω; Transducer: 12 to 16 x

9 FOH Speaker 2.5" mid/high drivers, 2x 6.5" bass drivers; IP rating: IP55 or better; with Included hardware : Tilt bracket, Pan 2 Nos. 176,571.35 353,142.71

Supply, Installation, testing and commissioning of 4-channel Class-D networked Dante amplifier With 1500W

total power; Max Power Per channel 1000 W @ 2Ω, 800W @ 2.7 Ω, 600W @4 Ω, 1000@8 Ω; Bridge mode power

:750 W @ 2Ω, 750W @ 2.7 Ω, 750W @4 Ω, 750@8 Ω; Max channel power: 70v @:375;100v @ 1000; Frequency

resposne:20 Hz to 20 kHz (±1 dB); Sampling rate: 96 kHz ; Latency: 0.77 ms; 12 x 12 matrix mixer, 4 x mic/line

Dante based quad inputs; Gain :0 to 60 dB; + 48 V Phantom power; Input impedance : >10 kΩ; Crosstalk : <-80 dB; 1 x PoE Backup

10 channel Power power supply; danet sampling 48/96 kHz, eight (8) Dante inputs, eight (8) Dante outputs and four (4) mic/line 1 Nos. 339,658.82 339,658.82

Amplifier inputs ; Cooling : Front-to-rear.

Digitally signed by AMIT

Supplying, Installation, testing and commissioning of Multi Channel Class D amplifier providing total rated output

power 600 W or better; Minimum 4 Channel Input and Output, Power sharing on all outputs; Maximum output

power single channel (power sharing): 500 watts or more; Impedance support: 4 ohm, 8 ohm, 70 V, 100V;

Nominal Gain 36.2 dB or better , Signal to Noise Ratio > 103 dB or better, Damping factor : > 1000 or better;

Quad Channel THD+N < 0.1 % or better, 2 x 6-pin Euroblock, 1x RJ45, Audio limiters, high temperature, DC, HF, short circuit, back-

Power Amplifier EMF, peak current limiters, inrush current limiters, mains over/under voltage protection.

Supply, Installation, testing and commissioning of 12x8 Digital signal Processor models with 12 mic/line inputs

and 8 line outputs; 12 channels of AEC and 24x48/48x24 dante enabled; AUDIO SYSTEM should include a

configurable USB Audio interface- /output configuration of the USB Audio Interface can be set to 0x8, 2x6, 4x4,

6x2, or 8x0 ; should be certified for microsoft Teams and Zoom; 64 bit floating point audio DSP processing;

Equipped with selectable 48 volt phantom power for the iminimum 8 nos. analog inputs; Should have 24 bit/48

kHz analog to digital and digital to analog converters; 8 or more DSP Configurator presets; Audio system gain:

Balanced output: 0 dB, unbalanced output: -6 dB or better; Frequency response: 20 Hz to 20 kHz, ±0.2 dB or

better; THD + Noise <0.02%, S/N: Analog In to Analog Out >109 dB, Analog In to Digital Out 110 dB, Digital In to

Analog Out 115 dB, Crosstalk should be <-90 dB, impedance >10k ohms; Up to eight audio file players can be

used to play back audio files; Cer fica on: UL, CE, FCC Class A, ICES, RoHS, WEEE.

Supply, Installation, testing and commissioning of 6x4 Digital Matrix Processor DSP with 6 mic/line inputs and 4

line outputs; Six channels of AEC; AUDIO SYSTEM should include a configurable USB Audio interface- /output

configuration of the USB Audio Interface can be set to 0x8, 2x6, 4x4, 6x2, or 8x0 ; should be certified for microsoft

Teams and Zoom, 24 x 48 Dante enabled audio networking & AES67 support; 64 bit floating point audio DSP

processing; Equipped with selectable 48 volt phantom power for the analog inputs; Should have 24 bit/48 kHz

analog to digital and digital to analog converters; 8 or more DSP Configurator presets; Audio system gain:

Balanced output: 0 dB, unbalanced output: -6 dB or better; Frequency response: 20 Hz to 20 kHz, ±0.2 dB or

better; THD + Noise <0.02%, S/N: Analog In to Analog Out >109 dB, Analog In to Digital Out 110 dB, Digital In to

Analog Out 115 dB, Crosstalk should be <-90 dB, impedance >10k ohms; Up to eight audio file players can be

used to play back audio files; Cer fica on: UL, CE, FCC Class A, ICES, RoHS, WEEE.

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of IP ethernet based dual channel Wireless Handheld microphone

with dynamic cardoid/supercardoid capsule , Sound pressure level 154 dB SPL or better: Frequency response :

20Hz - 20kHz ; Total harmonic distortion (THD) : ≤ -60 dB; should support up to 293 channels in cascading or

single unit mode, Network enabled for control, Transducer Principle type: Dynamic; Polar Pattern : Cardioid;

Dynamic range: 134 dB or more ; System latency: 1.9 ms or less; Up to 88 MHz switching bandwidth RF Power :

Dual Channel 10mW-50mW for pickup range up to 100 meter; Secure AES 256 encryption, Sensitivity : 2.1mV/Pa. user

14 Digital Wireless interface with OLED display, control all the transmitter settings directly from handheld microphone, Up to 12 6 Nos. 258,638.17 1,551,829.01

Handheld Mic hours of operation time with rechargeable lithium ion battery , Switch included 2x handheld transmitter with

mute switch along with rechargeable ba eries & receiver.

Supplying, Installation, Testing and Commissioning of Two slot Charging Set with network monitoring support.

POE support along with network enabled charger for two individual charging bays. Power supply should be

Microphone included. Microphone and accessories should be from same OEM

Battery Charger

Supply, Installation, Testing & Commissioning of 40-45 cm long cardoid/Supercardoid Gooseneck microphone

along with integrated status light ring: Frequency response : 50 Hz to 20 kHz; pcikup of 120° angle of acceptance,

Gooseneck Nominal impedance : < 100Ω; Max SPL : 130dB; Microphone Type : Pre-polarised condenser and RF shielding

16 against intermodulation from wireless devices, impedance less then 100 ohm. Sensitivity: 15 mV/Pa. Power 4 Nos. 25,474.19 101,896.77

supply microphone: 12 V - 48 V along with XLR-3/5M connector.

Supply, Installation, Testing & Commissioning of Active Antenna Splitter with 2 x 1:4 or 1 x 1:8 active connections,

which work on 56 MHz Bandwidth and allow for up to 90 channels, Supports Mobile App streamlines setup and

operation and eliminates complicated menus, Frequency range: 470 – 694 MHz, along with Automated setup

17 Antena Splitter creates reliable connections with minimal time and effort. 1 Nos. 69,222.25 69,222.25

Supply, Installation, Testing & Commissioning of Antenna : Passive directional UHF antenna with frequency ranges

: 470 – 1075 MHz; Gain : 5 dBi; Impedance: 50 Ω; Front-to-back ratio : > 14 dB; Apex angle : 100°; BNC

18 Connectivity 2 Nos. 38,021.58 76,043.15

Supply, Installation, Testing & Commissioning of Ceiling Microphone tile with Min of 28 x Pre-polarized condenser

capsule or higher, frequency response: 160 Hz - 18,000 Hz or better ; Sensitivity: 0 dBV/Pa or better ; Sound

pressure level : 104 dB SPL opr better , Signal-to-noise ratio: 83 dB or better ; Dynamic range 93 dB(A) or better,

Ceiling Tile Latency : 4 ms or better ; Adaptive beamforming technology or better, Audio output : 1 x 3-pin terminals ;

19 Should have 2 x Digital Dante Network Audio (RJ-45 Primary and Secondary), Voltage 44 – 57 V DC or better, 2 Nos. 656,209.93 1,312,419.86

complete with standard accessories. microphone must have dante support. Should have Support UL 62368 Safety

Video System - -

Digitally signed by AMIT

Supply, Installation, Testing and Commissioning of Indoor LED Video Wall with mounting structure, Area: 2.88m ×

1.6m or more, 130" or higher , Pixel Pitch: 1.58mm or less, Pixel Configuration: 3 in 1 SMD; Weight per Square

Meter (kg/㎡): 26 or less; Physical Pixel Density (pixels/㎡): 400000 or better; Cabinet Resolution (WxH): 608x171

or better; Cabinet Aspect Ratio (W:H): 32:9; Cabinet Depth: 40mm or less; Unit Case material: Die casting

Aluminum; Minimum Brightness ( After Calibration): 800 cd/m2 or more; Color Temperature: 3000 - 10000 or

better; Visual Viewing Angle (Horizontal): 160 or more; Visual Viewing Angle (Vertical): 160 or more; Brightness

Uniformity: 97% or more; Color Uniformity: ±0.003CxCy; Contrast Ratio: 7000 or more; Processing Depth (bit): 16

or more; Power Consumption (W/㎡, Max.): 550 or less; Power Supply (V): 220 to 240; Frame Rate (Hz): 50 or

more; Refresh Rate (Hz): 3840 or more; Certifications: BIS; Lifetime: 100000 hr. or more; Operating Temperature:

-10∘ to +40∘ or better; Operating Humidity: 0~80%RH; LED Controller: Inputs: 1 x HDMI, 2x DVI supporting

20 130" Active LED resolutions up to 1920×1200@60Hz and customizable resolutions. Features 4× Gigabit Ethernet outputs with a 1 Nos. 3,234,992.13 3,234,992.13

total loading capacity of 2.60 million pixels (maximum width: 4096 pixels; maximum height: 2560 pixels). Supports

arbitrary video switching, cropping, scaling, and screen deviation correction. Audio Ports: In & out both;

Controller and screen should be provided by same OEM; Control Ports: LAN/RS232; Audio Input/Output: Yes;

including wall fabrication for installing the video wall.

Supplying, Installation, testing and commissioning of 86", 4K Multi touch interactive display, 450 cd/m2, built in

Mali470 MP3 GPU, CA55 Quad core CPU and Android Pie 13.0, 8GB Memory, 128 GB storage, Built in Wifi &

Bluetooth, 2x25 W - Front Facing Speakers, Continuous Touch Points: 20 Points: Windows,10 Points: Android.

21 Interactive Display Port terminals: 3 x HDMI IN, 1 x VGA, 4 x USB, 1 x OPS slot (15W), 1 x HDMI Out, 1 x RJ45, complete with OPS and 2 Nos. 444,126.04 888,252.08

standfard accessories as required.

Supplying, Installation, testing and commissioning of 55" ELED/DLED Display with Resolution :3840 X 2160 or

better; Aspect ratio : 16:9 or better; Brightness: 500 Cd/m2 or better; Contrast: 4000:1 or better; Viewing angle

:178°(H)/178° (V) or better; Surface haze: 28% ; CPU: Quad core ; GPU: ARM Mali; Android ; RAM &ROM: 2 GB

DDR4 memory &16 GB storage or better, Wifi/Bluetooth:Yes; Should have interface :HDMI IN 2.0 X 3, USB 2.0 x 2

,, Line Out X 1 (3.5mm Jack), RJ45 X 1, RS232 X Yes better; Should have 10 x 2 Watts or more built in Speakers ;

55" Display 24/7 operation;Temperature: 10ºC～40ºC. 1 Nos. 78,955.74 78,955.74

Supply, Installation, testing & commissioning of 75" 4K UHD(3840 X 2160) Slim DLED display,Aspect Ratio 16:9,

Brightness 500 Cd/m2 or better, Pixel Pitch 0.4296mm(H) × 0.4296 mm(V) or better,Haze 28% or better,Viewing

Angle 178° or better, Android OS, Quad-Core ARM Cortex-A55 CPU, ARM Mali-G31 MP2 GPU, 4GB DDR4 memory,

32GB storage, HDMI IN X 3, HDMI Output 1 ,USB 2.0 X 1 ,USB 3.0 X 1 , RS232 X 1, RJ45 X 2(IN/OUT), USB Type-C

X 1 ,Ram 4GB memory, 32GB storage 24W in built speaker,Operation Temperature:0℃ - 45℃, Operation

Humidity: 10% - 90%.

Bracket for 86" Supply, Installa on, tes ng & commissioning of ltable/pushpull bracket for 86" display

Digitally signed by AMIT

Supply, Installation, testing & commissioning of tiltable/pushpull bracket for 75" display

Bracket for 75"

Supply, installation, testing & commissioning of 15.6" Ultra-thin Motorised Monitor with retractable Lift, with touch,

Interface-VGA input, HDMI input, Screen Ration-16:9 or better, Dynamic Contrast: 800:1 or better, Resolution:- 1920 X 1080

or better, with brightness:-300cd/m²,multi capacitive touch and response of touch time is < 5ms, panel buttons with ON

Retractable /OFF /UP /DOWN /STOP /Signal switch /monitor setting with monitor lift is provided with an Automatic power for the

25 monitor going up and down, equivalent complete with standarad accessories as required.

Supply, Installation, Testing & Commissioning of 4K Wireless Presentation Gateway

with POE/POE+ support, 1 HDMI input, 2x HDMI out for Dual Screen Display, analog

audio input and output; Supports resolutions up to 4096x2160 at 60Hz with 4:4:4 chroma

sampling at 8 bits of color; 128-bit or more encryption; Microsoft windows , Mac , Apple,

Android Operating system supports, Full screen and four window Simultaneous

display of content from 4 different sources through dongle/ software app; Share

content without installing software via AirPlay, Miracast, WebShare; HDMI audio

de-embedding, should supports moderator mode, H.264 Streaming Signage & Digital

Signage feature support option; customizable welcome screen, screen mirroring and

control; CEC support, Ethernet monitoring and control; Display control via RS-232, CEC

26 Wireless Presentor over HDMI, and IR/Serial; Automatically mute video and sync output to the display 3 Nos. 400,305.60 1,200,916.81

device when no active connections are detected; video player controls; option to connect

USB peripheral devices for wireless use the video and audio for remote participants with

a Windows or macOS laptop running Teams, Zoom, or other UC meetings. Should allow

presentation notes, previews, and annotations, from Microsoft PowerPoint or similar

applications. Dual Ethernet ports segment guest and private users for secure

Supply, Installation, Testing & Commissioning of 11-12" Tab/ipad with Wi-Fi, 8 GB or

more Memory, Octa-Core or better processor for viewing the content. Should have TFT

sceen, Type-C port, OS: Android/IOS, Pen, Rear Camera - Resolution of 13.0 MP or

better, IP 68 or better, External Storage Support Up to 2 TB. should be including Type-

C-C cable, PEN and stand cover with pan holder.

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of Digital Interactive Podium in Metallic Frame and Wooden Top

with 21-24 inch Full HD Interactive Display, with Motorized Tilting of the Interactive Panel, with provision to

install Gooseneck Microphone with mute / unmute button, Interactive panel, Keyboard Tray and space to store

AV equipment, Interactive display with full HD resolution of 1920x1080, Technology IPS LCD, Aspect ratio16:9,

Brightness 250 cd/m2, Contrast ratio 800:1. Top connectivity plate with HDMI, USB x 2 and Power socket for

28 Podium external Laptop connectivity. and output and power socket, laptop tray, side visualiser tray and built in power 2 Nos. 383,812.63 767,625.25

distribution kit along with desktop PC with i5/i7 processor, 8GB RAM and 256 GB SSD, complete with standard

accessories as required.

Supply, installation, testing & commissioning of Cable Cubby/cable management box with flap cover, having 6

nos. pass through holes for AV connectivity and 2xUniversal Power Socket; 1xUSB-A & 1xUSB-C chargings,

Cable provision for 1xHDMI , 1xType-A USB , 1xType-C USB , 2xCAT 6 Network/RJ-45 connectivities. all complete.

30 Recording & streaming, Camera and Video Collaboration System - -

Supply, Installation, testing & commissioning of Full HD 1080p @ 60 frames per second PTZ Camera with

minimum 20X Optical Zoom and 12X digital Zoom , CMOS Sensor 1/2.8" or better and FoV of minimum 65 deg,

min 200 Presets. Camera should support simultaneous outputs through Ethernet, HDMI, 3G-SDI, USB3.0, Audio In

and can be controlled via RS232 & 422 In & Out & IP, USB. Panning angle -170° ~ +170°, Tilting angle -30° ~ +90° .

31 PTZ Camera The tilting and panning speed of camera should be minimum 220° per second. Video S / N Ratio > 50dB; Camera 7 Nos. 337,755.11 2,364,285.77

should support SRT, FreeD Protocol, PoE, UVC 1.1 or better. .

Supply, Installation, testing & commissioning of Recording, Streaming & Webcasting Hardware simultaneously,

Built-in 4x HDMI & IP Inputs with 4x Line Inputs, 2x HDMI Outputs. The system should be capable to record upto

any four inputs simultaneously in a single frame and as well as individual sources simultaneously. Should have

4 Channel minimum 1TB inbuilt storage and can be connected to local NAS storage. The system should be able to support

32 Recoreder and minimum 3 unicast streams.The recorded files should have the option of time and date stamp. 1 Nos. 649,191.64 649,191.64

Supply, Installation, testing & commissioning of Recording, Streaming & Webcasting Hardware simultaneously,

Built-in HDMI, 3G-SDI, IP & USB 3.0 Video Inputs with 1x Line In and 1x XLR Input, 2x HDMI Outputs, Can record

2 Channel upto any two inputs simultaneously in a single frame and as well as individual sources simultaneously. Should

33 Recoreder and have minimum 1TB inbuilt storage and can be connected to local NAS storage. The system should be able to 1 Nos. 517,598.74 517,598.74

streamer support minimum 3 unicast streams.The recorded files should have the option of time and date stamp.

Supply, installation, testing & commissioning of POE based AV over IP and NDI HX3 4K Bridge with USB Extension

over IP, Instant source switching, IP Video to USB Conversion, USB Host x1 , Type-C x1 and HDMI x 1 outputs,

Audio Input Line In/MIC In ,3.5mm x1, Audio Output, UVC support, PIP / PBP, Video Wall: 3x3 or more support,

34 Audio Decoding & Audio Routing. 2 Nos. 186,423.28 372,846.55

Digitally signed by AMIT

35 Control & Switching Device - -

Supply, Installation, Testing & Commissioning AVoIP Encoder supports 4K UHD over Gigabit Ethernet; Inputs min

2x HDMI 2.0 4K60 4:4:4 & 1x USB-C capable of scaling and outputting video with auto-switching between all the 3

input sources; HDCP 2.3; HDMI Loop Out up to 4K60 4:4:4; USB Host port; LPCM audio support upto 8 Channels

from HDMI Input; Embedded audio input; Native AES67 Network Audio; Adjustable Video Bitrate upto 800 Mbps

with bit-rate compression CODEC w/ built-in AI; Video Codec: JPEG2000 based visually lossless video compression

algorithm; latency: 5 ms at 4K60 4:4:4; AES-256 Encryption or better; 2 or more LAN ports with POE power

sharring;; VLAN tagging to saperate Video traffic from data & voice and VLAN Trunk mode capability; RTP audio

AV Over IP stream capability; ICMP,IGMP & PIM feture support; Supports Video, Audio, USB, KVM & RS232 independent

36 matrix routing; EDID managment; USB over IP (KVM), RS-232 over IP, IR over IP, GPIO over IP; Standard PoE 16 Nos. 164,573.37 2,633,173.93

Power 15 W or lower; Integrated Software management platform supports for system monitoring & control;

Future upgradable DANTE; support 802.1x, HTTPS, SSH security encription; Compliance supports TAA, CE, FCC, C-

tick, RoHS, WEEE.

Supply, Installation, Testing & Commissioning AVoIP Decoder supports 4K UHD over Gigabit Ethernet; Outputs

min 1x HDMI 2.0 4K60 4:4:4 & 1x USB-C capable of scaling and outputting video with auto-switching; HDCP 2.3;

min 2x USB peripheral ports; LPCM audio support upto 8 Channels from HDMI Input; De-embedded audio output;

Native AES67 Network Audio & Dolby enabled; Adjustable Video Bitrate upto 800 Mbps with bit-rate compression

CODEC w/ built-in AI ; Video Codec: JPEG2000 based visually lossless video compression algorithm; latency: 5 ms

at 4K30 & 4K 60 4:4:4; 2 or more LAN ports with POE power sharring; VLAN tagging to saperate Video traffic from

AV Over IP data & voice and VLAN Trunk mode capability; RTP audio stream capability; Built-in 16x16 videowall function with

Decoder rotation support upto 270 degree; Text overlay capability; ICMP,IGMP & PIM feture support; Auto Video Scaler 4K

in/1080P out & 1080P in/4K out; Supports Video, Audio, USB, KVM & RS232 independent matrix routing ; USB

over IP (KVM), RS-232 over IP, IR over IP, GPIO over IP and CEC over IP; Standard PoE Power 15 W or lower;

Integrated Software management platform supports for system monitoring & control; Future upgradable DANTE;

support 802.1x, HTTPS, SSH security encription; Compliance supports TAA, CE, FCC, C-tick, RoHS, WEEE

Supply, Installation, Testing & Commissioning of HDMI Distribution Amplifiers, Six Output 4K/60 4:4:4 HDMI 2.0,

18 Gbps, HDR, Deep Color up to 12-bit, 3D, HD lossless audio formats, and CEC control, HDCP 2.3 compliant, EDID

38 HDMI DA manager; Selectable output muting via RS-232/IP control; USB port; 1 Nos. 192,454.62 192,454.62

Supply, Installation, Testing & Commissioning of 6-7 port usb HUB for chairman's monitor content monitor for

touch connection.

Digitally signed by AMIT

Supply , installation , testing and comissioning of AV Control Processor, should have 1x RS232/RS422/RS485, 2x

bidirectional RS232 or more, 2 or more IR/Serial, 4 or more Relay, 4 or more x Digital IO. It can control at least 30

devices over more Ethernet port supporting 10/100/1000Base-T and should support IEEE 802.1X, IPv4, TCP, UDP,

DHCP, DNS, HTTPS, NTP, SFTP, SMTP, SNMP, SSH protocols. Should have SDRAM: Min 1GB or more and Flash

Memory: Min 8 GB or more. Optionally, it should be supplied with necessary license to integrate with

Control System-

40 iOS/Android device. Should have Built-in IR receiver for recording IR commands. Should be Operational in up to 1 Nos. 453,269.55 453,269.55

45°C temperature. Should have Regulatory compliance: CE/UL or any equivalent.

Supply, Installation, Testing & Commissioning of Av control processor 1 x RS-232/ RS-422/RS-485 ; 1 x

bidirectional RS-232; 4 x Digital I/O; 1 x IR/Serial; 2 x relays ; 1 GB SDRAM & 8 GB Flash Memory; Data rate:

10/100/1000Base-T, half/full duplex with autodetect; support protocols : ARP, DHCP, DNS, HTTP, HTTPS

Control System- (redirect), ICMP, IEEE 802.1X, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP; Supports control system

Type 2 synchronization; Supports 802.1X Authentication; Front panel port status indicators;

Supply , installation , testing and comissioning of 10-12" wirelss touch panel with LED backlit Multi-Touch display

with IPS technology (Liquid ratina display), OS: IOS, wifi, 128GB storage capacity, USB type-C connectivity, 500

Wireless Touch nits or more brigjhness, with docking sta on. Should support the control applica on for automa ons.

Supply , Installation, Testing & Commissioning of 10" Tabletop capacitive touchscreen with 1280x800 resolution

and 24-bit color depth or better, Pixel density 149 PPI; Aspect ratio - 16:10; Brightness- 420 nits; Contrast -

800:1; Viewing angle ±85° horizontal, ±85° vertical; SDRAM- 2GB & Flash memory- 8 GB or more; Motion &

Lighting sensor- On/off OR Auto/manual; Connectors — 1 x RJ-45; Data rate: 10/100/1000Base-T, half/full duplex

with autodetect ; Protocol DHCP, DNS, HTTP, HTTPS, ICMP, IEEE 802.1x, SFTP, SSH, TCP/IP, UDP/IP; Faster quad-

10" wired Control core processing and eight times more memory, toughend Gorilla Glass screen, scratch, and smudge-

43 resistant, Power over Ethernet provides power and communication over a single Ethernet cable, 1 Nos. 397,842.62 397,842.62

built-in speaker with Frequency response : 1000 Hz to 20 kHz or better, USB port .

Supply, Installation, Testing and Commissioning of 7-8" Capacitive touchscreen with 1024 x 600 resolutionor

better; Aspect ratio: Widescreen/16:10; color depth 24-bit or more; Brightness- 420 nits or more; Contrast -

700:1; Viewing angle ±75° horizontal,+70°/-75° vertical or better; SDRAM- 2GB & Flash memory- 8 GB or more;

Connectors — 1 x female RJ-45; Data rate 10/100/1000Base-T, half/full duplex with autodetect ; Protocol DHCP,

DNS, HTTP, HTTPS, ICMP, IEEE 802.1x, SFTP, SSH, TCP/IP, UDP/IP; Built-in speaker ; Motion & Lighting sensor-

7" wired Control On/off; Faster quad-core processing and eight times more memory, toughend Gorilla Glass screen, scratch,

Panel and smudge- resistant, Power over Ethernet provides power and communication over a single

Ethernet cable . built-in speaker with Frequency response : 1000 Hz to 20 kHz or better, USB port .

45 Misc items - -

Digitally signed by AMIT

Supply and laying of 80/.2 2.5 sqmm Twisted Pair Speaker cable with soft rubber-pvc sheatingetc. all complete as

per approved drawings, tender specifications and direction of Engineer-in-Charge.

46 Speaker cable 250 Mtr. 186.42 46,605.82

Supply, Installation, Testing and Commissioning of 40x1G PoE+ 480W power budget and 8xSFP 1G Managed AV

over IP network Switch, support for dante, av over IP, AES67, and AVB profiles. 96 Gbps Switching, 32 Mb Packet

Buffer, latency <2.46µs 1G, 512 IPv4 & 128 IPv6 IP Multicast Routing Entries, 4K VLANs, 96 Gbps non-blocking

48 port Network fabric across all 48 ports, USB-C and RJ45 RS232 console ports and USB-A storage port, Auto-Trunk, Auto-LAG and

switch IGMP Plus, IGMPv3 MLDv2 Snooping, Proxy ASM & SSM.

Digitally signed by AMIT

Supply, Installation, Testing and Commissioning of 24x1G PoE+ 300W power budget or more, 2x1G and 4xSFP

fully Managed AV over IP network Switch, support for dante, av over IP, AES67, and AVB profiles. 64 Gbps

Switching, 16 Mb Packet Buffer, latency <2.15.µs 1G, 512 IPv4 & 128 IPv6 IP Multicast Routing Entries, 4K VLANs,

24 port Network

48 60 Gbps non-blocking fabric across 30 ports, USB-C and RJ45 RS232 console ports and USB-A storage port, Auto- 2 Nos. 213,180.50 426,361.00

Trunk, Auto-LAG and IGMP Plus, IGMPv3 MLDv2 Snooping, Proxy ASM & SSM.

Supply, Installation, Testing & Commissioning of Dual-Band PoE Multi-Gig Insight Managed WiFi Access Point;

Dual band 2x2 (2.4GHz and 5GHz), 80MHz or more channelization, 1.8 Gbps throughput, Backward compatible to

802.11b/g/ n/a/ac; POE supported, should support next generations devices like smart phones, IoT devices, and

49 notebook computer; OFDM and OFDMA support, WPA, WPA2, WPA3 support; Antenna Gain: 3.8/4.5dBi for 1 Nos. 27,634.51 27,634.51

Supply and laying of 2 meter High-Speed Active HDMI Cable with Gold-Plated connectors; video capability:

4K@60Hz 4:4:4 18Gbps; video complaince support- HDMI 2.0, HDCP 2.3, HDR; Should have CEC Support; Cable

50 HDMI Cable Construction- Solid Core Oxygen Free Copper; Regulatory- CEC ,RoHS Compliant, REACH Compliant. 43 Nos. 2,631.86 113,169.89

Supply , installation , testing and comissioning of 50 ohm Microphone Antenna Cable along with connectors and

51 accessories as required. 60 Mtr. 855.35 51,321.23

Supply, installation, testing & commissioning of 4 pair unshielded TIA/EIA-568-C Category 5e cable with 24AWG

or better Solid annealed bare copper conductors, High-density polyethylene insulation, Flame rated PVC jacket,

52 CAT5e/6 Cables tested to 350 MHz, NEC CMR, CEC CMR FT4, RoHS compliant. 1200 Nos. 87.73 105,274.32

Supply, Installation, Testing & Commissioning of 37 U Equipment Rack for housing all rack mountable equipments

37U Equipment with internal wiring, front glass door; heat dessipation fans; movement wheels, power distribution units etc., size:

rack 600 x 800 mm; complete with standard accessories.

Supply, Installation, Testing & Commissioning of 27 U Equipment Rack for housing all rack mountable equipments

with internal wiring, front glass door; heat dessipation fans; movement wheels, power distribution units etc., size:

54 600 x 800 mm; complete with standard accessories. 1 Nos. 65,138.49 65,138.49

Supply, Installation, Testing & Commissioning of 19 U Equipment Rack for housing all rack mountable equipments

55 with internal wiring, front glass door; heat dessipation fans; movement wheels, power distribution units etc., size: 1 Nos. 47,921.75 47,921.75

600 x600 mm. complete with standard accessories.

Cable and Supply, laying and termination of required USB cable and Connectors.

56 Connectors (MR 1 Lot 87,728.60 87,728.60

Cable and Supply, laying and termination of required USB cable and Connectors.

57 Connectors (BR & 2 Lot 38,381.26 76,762.53

58 Press distribution box for Audio and Video for media having output port for HDMI, HDSO1, Audio 1 Lot 600,000.00 600,000.00

Total Amount 40,205,981.42

Total Amount 40,205,981.42

Digitally signed by AMIT

Project Name:- Renovation/ Restoration and addition/ Alteration Interior/ Modernization of existing

buildings/ facilities of ICSSR

Furniture Estimate

S.No. Specification Total unit

Supplying and placing in position of 19 seater modern design conference table with cable organisers size :- (w)

6600mm x (d) 1500mm x (h) 760mm.material - engineered wood - mdf. table top material- engineered wood. leg

material- engineered wood. finish matte. colour & colour family- brown - walnut. experience the perfect harmony

of artistry and practicality with our sculptural collection. an intricately grooved panel on the tabletop and

designer base add character to this conference table, while the circular cable organisers ensure a tidy setup.

crafted from premium engineered wood in walnut finish. spacious tabletop accommodates multiple

participants, ideal for collaborative discussions and presentations. intricately grooved wooden panel and

designer base add character to the tabletop. circular cable organisers ensure a tidy and clutter-free workspace.

premium pu polish with low chemical emissions ensures healthy indoor air.All complete as per specifications or

equivalent and direction of Engineer-in-Charge.

Supplying and placing three-seater sofa that shall be constructed from natural hard wood and commercial

plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa size

is 1830mm(l) x760mm(d)x 790mm(h) shall have spring attached and also be padded separately. the seat shall

have double cone spring integrated with epitome of luxury. the frame shall be padded with high resilience

polyurethane foam having density 45kg/m3 in seat and 32kg/m3 in back. there shall be cushion arm

provided padded with high resilience polyurethane foam having density 32kg/m3. the complete structure

2 shall be upholstered with leatherette tapestry 0.8 +/- 50.1 mm thick and 535 gsm. the combination construction 2 nos 70522.83 141045.66

structure is made in moisture content shall be less than (10-12) %. thickness of plywood used (mm) shall be 12

mm grade is 303 Indian standard for commercial (common) and moisture proof plywood (tentative). under

structure shall consist of ms powder coated square pipe having cross- section area 25mm x 25mm with

1.6mm thick the legs shall be made up of powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall

be co-polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. The seat size shall be

490 +/- 510mm(d) x 450 +/- 510mm(h) or equivalent . All complete as per specifications and direction of

Engineer-in-Charge.

Digitally signed by AMIT

Boucle 3 Seater Curved Sofa Dimension: (W) 2400mm X (D) 1030mm X (H) 665mm

Supplying and placing three-seater sofa that shall be constructed from natural hard wood and commercial

plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa size

is (W) 2400mm X (D) 1030mm X (H) 665mm shall have spring attached and also be padded separately. the seat

shall have double cone spring integrated with epitome of luxury. the frame shall be padded with high resilience

3 polyurethane foam having density 45kg/m3 in seat and 32kg/m3 in back. there shall be cushion arm provided 2 nos 168000.27 336000.54

padded with high resilience polyurethane foam having density 32kg/m3. the complete structure shall be

upholstered with leatherette tapestry 0.8 +/- 50.1 mm thick and 535 gsm. the combination construction structure

is made in moisture content shall be less than (10-12) %. thickness of plywood used (mm) shall be 12 mm grade

is 303 Indian standard for commercial (common) and moisture proof plywood (tentative). All complete as per

specifications and direction of Engineer-in-Charge.

Supplying and placing in position of Wall Hung TV Cabinet as per drawing. The work surface top should be of

4 thickness 25mm top prelaminated particle board with 2mm thick PVC edge banding. The side & back panel are 3 nos 48908.69 146726.08

made up of 25mm thick prelaminated particle board with 2mm thick PVC edge banding.

All complete as per specifications or equivalent and direction of Engineer-in-Charge.

Supplying and placing in position of chair as per drawing. Sense, simplicity and style best describe the lounge

chair. Its practical structure offers you a plush. Featuring a high back and slim, sturdy armrests, the chair is proof

5 that form and function can truly coexist.Fabric upholsterywith chrome legs .Dimesnion: 543mm(L) x 1 nos 41671.09 41671.09

558mm(D) x 822mm(H).Material :Fabric/leatherette , fixed Legs Material :chrome . Seat: Revolving . All

complete as per specifications or equivalent and direction of Engineer-in-Charge.

Supplying, and placing in position of Solid Wood Coffee Table of Size: 1150Wx550Dx450H mm. Material &

Subtype: Solid Wood - Beech Wood,Glass - Clear Glass, Table Top Material: Clear Glass, Frame Material: Solid

6 Wood, Leg Material: Solid Wood, Finish: Matte, Colour & Colour Family: Brown - Dark Oak, Table Top 2 nos 45399.55 90799.10

Thickness: 10mmAll complete as per specifications or equivalent and direction of Engineer-in-Charge.

Supplying, and placing in position of Round Coffee Table Material & Subtype Laminate, Solid Wood -

Steam Beech Wood, Engineered Wood - Particle Board, Base Material Solid Wood, Finish

7 Matte, Colour & Colour Family White - Off, Brown - Walnut, Dimension (W) 820mm X (D) 820mm X (H) 1 nos 31362.97 31362.97

410mm, Table Top Thickness 18mm. All complete as per specifications or equivalent and direction of

Engineer-in-Charge.

Supplying, and placing in position of Round Side Table in Marble-Finished Tabletop Material &

Subtype Laminate, Solid Wood - Steam Beech Wood, Engineered Wood - Particle Board, Base

8 Material Solid Wood, Finish Matte, Colour & Colour Family White - Off, Brown - 1 nos 17984.36 17984.36

Walnut, Dimension(W) 420mm X (D) 420mm X (H) 460mm, Table Top Thickness18mm. All complete as per

specifications or equivalent and direction of Engineer-in-Charge.

Digitally signed by AMIT

Supplying and placing in position of 17 seater modern design conference table, conference desk with cable

organisers size :- (w) 6000mm x (d) 1500mm x (h) 760mm.material - engineered wood - mdf. table top material-

engineered wood. leg material- engineered wood. finish matte. colour & colour family- brown - walnut.

experience the perfect harmony of artistry and practicality with our sculptural collection. an intricately grooved

panel on the tabletop and designer base add character to this conference table, while the circular cable organisers

9 ensure a tidy setup. crafted from premium engineered wood in walnut finish. spacious tabletop accommodates 1 nos 243337.20 243337.20

multiple participants, ideal for collaborative discussions and presentations. intricately grooved wooden

panel and designer base add character to the tabletop. circular cable organisers ensure a tidy and clutter-free

workspace. premium pu polish with low chemical emissions ensures healthy indoor air. this product is a part of

the collection.All complete as per specifications or equivalent and direction of Engineer-in-Charge.

Supplying and placing in position of conference table as per drawing. The work surface top should be of

thickness 36mm top prelaminated particle board with 2mm thick PVC edge banding. The side panel are made

up of 32mm thick prelaminated particle & modesty panel are made out of 25mm thick prelaminated

10 particle board with 2mm thick PVC edge banding. The wire carrier should be made from 0.6mm thick CRCA 1 nos 1583906.97 1583906.97

& powder coated 40-50 microns. Also having a provision of 6 module flip top box (8 nos) & metal

raceway for wire flow. All complete as per specifications or equivalent and direction of Engineer-in-Charge.

Supplying, and placing in position of medium height storage @ 750mm height as per drawing . The storage unit

having Openable shutters with shelf in it. The modular storage unit top shall be made from 18 mm thick pre-

laminated particle board and rest of the sides as well as shelves and shutter to be made up of 18 mm thick pre-

11 laminated particle board while back to be made of 8 mm thick pre-laminated particle board. All edges to be 2 nos 44549.68 89099.36

provided with 2 mm thick PVC lipping. The storage unit having openable shutters withD shape handles &

locking arrangement.All complete as per specifications and direction of Engineer-in-Charge.

Supplying, and placing in position of medium height storage 2000mm(L) X 450mm(D) x 750mm(H) as per 1

drawing . The storage unit having Openable shutters with shelf in it. The modular storage unit top shall be made

from 18 mm thick pre-laminated particle board and rest of the sides as well as shelves and shutter to be made up

of 18 mm thick pre-laminated particle board while back to be made of 8 mm thick pre-laminated particle board. nos 35045.75 35045.75

All edges to be provided with 2 mm thick PVC lipping. The storage unit having openable shutters withD shape

handles & locking arrangement.All complete as per specifications and direction of Engineer-in-Charge.

Digitally signed by AMIT

Supplying and placing three-seater sofa that shall be constructed from natural hard wood and commercial

plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa size

is 1830mm(l) x760mm(d)x 790mm(h) shall have spring attached and also be padded separately. the seat shall

have double cone spring integrated with epitome of luxury. the frame shall be padded with high resilience

polyurethane foam having density 45kg/m3 in seat and 32kg/m3 in back. there shall be cushion arm

provided padded with high resilience polyurethane foam having density 32kg/m3. the complete structure

shall be upholstered with leatherette tapestry 0.8 +/- 50.1 mm thick and 535 gsm. the combination construction

structure is made in moisture content shall be less than (10-12) %. thickness of plywood used (mm) shall be 12

mm grade is 303 Indian standard for commercial (common) and moisture proof plywood (tentative). under

structure shall consist of ms powder coated square pipe having cross- section area 25mm x 25mm with

1.6mm thick the legs shall be made up of powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall

be co-polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. The seat size shall be

490 +/- 510mm(d) x 450 +/- 510mm(h).All complete as per specifications or equivalent and direction of Engineer-

Supplying and placing two-seater sofa that shall be constructed from natural hard wood and commercial plywood

having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa size is (W)

1920mm X (D) 1030mm X (H) 665mm shall have spring attached and also be padded separately. the seat shall

have double cone spring integrated with epitome of luxury. the frame shall be padded with high resilience

polyurethane foam having density 45kg/m3 in seat and 32kg/m3 in back. there shall be cushion arm provided

padded with high resilience polyurethane foam having density 32kg/m3. the complete structure shall be

upholstered with leatherette tapestry 0.8 +/- 50.1 mm thick and 535 gsm. the combination construction structure 2 nos 110955.92 221911.83

is made in moisture content shall be less than (10-12) %. thickness of plywood used (mm) shall be 12 mm grade

is 303 Indian standard for commercial (common) and moisture proof plywood (tentative). under structure shall

consist of ms powder coated square pipe having cross- section area 25mm x 25mm with 1.6mm thick the legs

shall be made up of powder coated round pipe of dia. 25.4mm with 1.6mm thick. there shall be co-polymer

polypropylene shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 490 +/-

510mm(d) x 450 +/- 510mm(h). All complete as per specifications or equivalent and direction of Engineer-in-

Supplying and placing in position of magzines library storage material : prelaminated particle board , storage size

: 800 mm (l)x 300 mm (d)x 1800 mm (h). colour : cherry & finish : laminate finish . * providing & suppling

placing position of modular storage top shall be made from 25 mm thick prelaminated particle board . * while rest

of the sides as well as shelves and shutter to be made up of 18 mm thick prelaminated particle board. machine

13 pressed exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade fixed 2 nos 52330.11 104660.22

duly pasted with the assistance of edge banding machine at 200 degreee celsius. * storage with construction is

open carcasses storage with 3 adjustable shelve per shelve 490 mm (d) x 430 mm (h),over all height of product is

@ 1800mm . * three layer prelaminated particles board ( wood product ) of grade ii type iii of is 12823/latest. All

complete as per specifications or equivalent and direction of Engineer-in-Charge.

Digitally signed by AMIT

Supplying, and placing in position Solid Wood Coffee Table of Size: 1150Wx550Dx450H mm. Material &

Subtype: Solid Wood - Beech Wood,Glass - Clear Glass, Table Top Material: Clear Glass, Frame

14 Material: Solid Wood, Leg Material: Solid Wood, Finish: Matte, Colour & Colour Family: Brown - Dark Oak, 12 nos 45399.55 544794.61

Table Top Thickness: 10mm. All complete as per specifications or equivalent and direction of Engineer-in-

Supplying and placing in position of side table as per drawing. The wooden centre table celebrates a marriage of

simplicity and functionality. Resting atop a clear glass, it create a stunning contrast of modern and rustic.

15 Timeless design that elevates your space.Open storage space for books or magazines with Kiln- dried solid wood 8 nos 28511.80 228094.36

is highly durable are made from sustainably sourced beech wood. All complete as per specifications or equivalent

and direction of Engineer-in-Charge.

Supplying and placing in position of modern design reception desk material : engineered wood - particle board

colour : slate grey with frosty white / finish : laminated. main table size : (l)2400 mm x (d)900 mm x (h)750 -

1050 mm. modern design reception desk in engineered wood make the products utile and a delight. timeless

design that elevates your office space structure of spacious reception desk, tabletop offers you a generous look for

work surface use premium quality materials overall size is (l)2400 mm x (d)900 mm x (h)750 mm which give

more surface area for work, table top made of 25mm thick also table top based on side panel's made 18mm thick

prelaminated particle board of grade ii type iii of is 12823/latest. combination construction of reception desk

16 above table top 18 mm thick counter top to table top height is @ 300mm, overall reception desk height is @ 1 nos 79811.09 79811.09

1050mm with counter top, table top made 25 mm thick prelam particle board work surface with the exposed

edges shall be finished with 2mm thick pvc edge binding tape of matching colour and shade fixed with hot melt

glue. along with 18mm thk additional modesty panel size is (l)1800 mm x (h)700 mm made by exclusive frosty

white colour with epic design & look.1 mobile pedestal (2 drawers + 1 filing cabinet )size is (l)450 mm x (d)450

mm x (h)725 mm in provided with central lock's for security and handle's are provided for easy of opening &

pedestal's move on nylon castors. three layer prelaminated particles board(wood product) of grade ii type iii of is

12823/latest, All complete as per specifications or equivalent and direction of Engineer-in-Charge.

Supplying and placing in position ergonomic office chairs with dimensions: Width 600±5 mm, Depth 640±5 mm,

Total Height 980-1080±5 mm, Back Width 425 mm (top) to 500 mm (bottom), Seat Width 500±5 mm, Seat

Depth 470±5 mm, and Seat Height 470-570±5 mm.Seat constructed with pre-moulded foam at 55 kg/m³ density,

hardness 25±3 kgf at 50% deflection per IS 3400, upholstered in micro fabric (100% polyester, 180 GSM,

abrasion >50,000 cycles, BS EN 1021 fire-rated). Features mesh backrest with injection-moulded PPGF 20%

17 frame (min. 4.8 mm thick, light grey), adjustable PU lumbar support (365×110×25 mm), self-calibrating 36 nos 14365.56 517160.10

multilock Bio Synchro mechanism (360° swivel, height adjustable, seat:back recline 3:7), one-way height-

adjustable arms (170-260 mm range, Delrin P500 button 73×18 mm), Class 4 gas lift , and light grey powder-

coated mild steel base (2 mm sheet thickness),with tolerances ±5 mm on dimensions and 5% on pipe

thicknesses/sizes.All complete as per specifications or equivalent and direction of Engineer-in-Charge.

Digitally signed by AMIT

Supplying and placing in position chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall be 980

to 1080 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-

5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3

density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro

fabric 100% polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric should be used. The chair shall be

supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey

shade, armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable

Lumbar Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better

comfort. Lumbar Support material Integrated one-piece Molded PU. The Chair should be provided with Self

18 Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing 33 nos 12868.80 424670.36

weight of the user. The mechanism shall allow 360 degree revolving feature along with height adjustablility. One

Way Adjustable Arms (Height) to be provied with height adjustment button of size 73mm x 18mm . Armrest

Height shall be 170mm to 260mm adjustable from Seat. The mechansim shall possess seat to back recline ratio of

3:7. The Gas Lift used shall be class 4 tested . Metal base shall be provided of light grey color matching the chair

back & armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey

theme of chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of +/- 5mm to be considered

for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes.

All complete as per specifications or equivalent and direction of Engineer-in-Charge.

Supplying and placing in position padded cushion high back (HB) chairs (or equivalent) featuring leatherette

upholstery on cushioned seat and backrest for premium comfort.Equipped with multiple recline lock positions,

19 pneumatic kneetilt mechanism for ergonomic support, Class 4 gaslift for height adjustment, chrome-plated fixed 17 nos 29672.01 504424.10

armrests, and heavy-duty chrome-plated metal base for stability.All complete as per specifications or equivalent

and direction of Engineer-in-Charge.

Supplying and placing in position ergonomic mesh back office chairs (or equivalent) with standard dimensions:

Width approx. 600 mm, Depth approx. 640 mm, Total Height 980-1080 mm, Back Width 425-500 mm, Seat

Width approx. 500 mm, Seat Depth approx. 470 mm, and adjustable Seat Height 470-570 mm.Features high-

density moulded foam seat (min. 55 kg/m³, IS 3400 compliant hardness), fire-retardant micro fabric upholstery

20 (>50,000 abrasion cycles), breathable mesh backrest with reinforced frame (min. 4.8 mm thick), adjustable 19 nos 14270.15 271132.91

lumbar support, synchro-tilt mechanism with auto weight-sensing recline (360° swivel, 3:7 ratio), height-

adjustable arms (170-260 mm range), Class 4 gas lift, and powder-coated metal base matching chair finish.All

complete as per specifications or equivalent and direction of Engineer-in-Charge.

Total Amount ₹ 6,906,216.65

Total Amount ₹ 6,906,216.65

Digitally signed by AMIT

Project Name:- Renovation/ Restoration and addition/ Alteration Interior/ Modernization of existing buildings/ facilities of ICSSR

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

Description Unit DSR No. DSR Rate MR Rate QtY DSR Amount MR Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS /HFFR PVC insulated copper

conductor single core cable in surface/ recessed steel conduit, with modular switch, modular plate, suitable GI box and

earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with

1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing

the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/

1.03 recessed steel conduit along with 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing Metre 1.50 480.00 1520.00 729600.00 0.00

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but

excluding modular plate etc. as required.

iii 3 pin 5/6 amp socket outlet Each 1.24.4 136.00 111.00 15096.00 0.00

iv 6 pin 15/16 amp socket outlet Each 1.24.5 219.00 74.00 16206.00 0.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular base & cover plate on existing modular metal boxes

etc. as required.

Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and

1.07 fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. Metre 1.57 807.00 17.00 13719.00 0.00

1.08 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. Metre 1.38 112.00 4.00 448.00 0.00

SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper

conductor, single core cable in surface/ recessed steel conduit as required.

iii 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 1.7.3 476.00 90.00 42840.00 0.00

Distribution Board,

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,

1.10 complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing 2.30

etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on

1.11 surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted 2.40

including earthing etc. as required. (But without MCB/ RCCB/ Isolator)

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet

steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar

for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3

phase outlets are required.)

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load

1.13 of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2.10

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker

1.15 (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and 2.14

commissioning etc. as required.

Supplying and fixing following rating, 240 volts, "C" curve, miniattlre circuit breaker suitable for lnductive loads of following

poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of

1.17 surface conduit, or cutting the wall and making good the same in case of recessed conduit as required 1.20

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in surface/ recess including cutting

the wall and making good the same incase of recessed conduit as required

Light Fixtures And Fan 0.00

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of

insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper

winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as

1.19 per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control 9.20

and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance

more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c

external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as

1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) Each 9.2.3 2695.00 31.00 83545.00 0.00

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing

1.21 opening including making good the damage, connection, testing and commissioning etc as required. 300 mm sweep Each MR 2500.00 17.00 0.00 42500.00

Installation, Testing and Commissioning of pre-wired, fluorescent fitting / compact fluorescent/ LED fitting of all types,

1.22 complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS/HFFR Each 1.41 1115.00 185.00 206275.00 0.00

PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, Testing and Commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5

sq. mm FRLS/HFFR PVC insulated, copper conductor, single core cable etc. as required.

Installation, Testing and Commissioning of exhaust fan in the existing opening, including making good the damage,

connection, testing, commissioning etc. as required.

TELEPHONE AND TV 0.00

Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored

telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but

excluding modular plate etc. as required.

i Telephone socket outlet Each 1.24.6 168.00 8.00 1344.00 0.00

ii TV socket outlet Each 1.24.7 168.00 8.00 1344.00 0.00

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic

laminated sheet cover in front including painting etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned

1.28 copper braid and protected with PVC sheath in the exisitng surface/recessed steel/ PVC conduit as required Meter 1.19 54.00 250.00 13500.00 0.00

Supplying, Installation, Testing and commissioning of CAT6A Copper Information Outlet (IO) with face plate of color as per

site requirement, should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D. All copper

Cable and Components should be from same OEM to maintain compatibility and interoperability etc. complete as required.

Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted Pair Cable in existing

conduit/ on surface, Category 6 Unshielded Twisted Pair, 4 pair should be complied as per UL/ETL verification program for

1.30 compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the range of 6.1mm nominal with Operating 39.17

Temperature Range : -5° to +60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg etc.

complete as required.

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with required suitable number of GI

1.31 couplers for joining raceways and fixing GI brackets and all accessories complete in all respect as per the directions of

engineer in charge

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at the intersection of raceways

supplied completely with base and cover plates, height adjustable junction box 65- 90 mm including all accessories ss plate

of 3mm thick complete in all respect as per the directions of engineer in charge

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed

temperature thermistor complete with base as required.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE

insulation, steel wire armouring & FRLS/HFFR outer sheath complete as required.

1.35 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required Nos 28.3.2 1025.00 15.00 15375.00 0.00

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel

1.36 conduit of following pairs, cores and size including connections and interconnections etc. as required. 28.5.3

speaker cable Single pair, 2-core, 1.5 sqmm Mtr 28.5.3.1 60.00 300.00 18000.00 0.00

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc.

Online UPS - Input supply: Single Phase, Output Supply: Single Phase. Supplying, installation, Testing & Commissioning of

following capacity at full load (Unity Power Factor) ON LINE Uninterrupted Power Supply (UPS) system suitable for Single

Phase input, Single Phase output AC Supply. The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes

back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load

(Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass, suitable

isolation transformer for additional protection against neutral faults etc. The UPS systems shall be Microprocessor based

Digital Control, using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter with PWM (Pulse Width

Modulation) Technology. The quality of design, manufacturing and inspection process should confirm to the relevant Inter-

national standards such as IEC/EN/VDE. The operating efficiency of the UPS systems shall be >95% at 100% non-linear

loads. Current total harmonic distortion(ITHD)/ total demand distortion (TDD) on the input grid shall be < 5% at 100 %load.

(The required LC filters shall be included in UPS cost), extreme power factor kit to be include to limit the input pf to 0.99 and

1.38 output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ) however UPS shall be suitable to take 26.10

load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC single phase 160-270V 50

Hz and delivering output AC supply true sine wave single phase 220/230/240 Volt, 50 Hz +/- 0.2Hz, Overload capacity of

120% for 10 mins and 150% for 1 minute. Operating temperature 0 to 40 0C, Relative humidity 0-95% non condensing, noise

level less than 60db at 1 meter distance, Protection for Under voltage, over voltage, abnormal output voltage, battery over

charging, output over current, short circuit, battery deep discharge , 10 KV surge. Display for watt/VA,Amp and Voltage

power parameters etc. UPS shall comply with low voltage electromagnetic compatibility (EMC) achieved as per EN 6204,

EN6204 Part I and Part 2, it shall be aVoltage and Frequency Independent (VFI) type UPS (as per standard IEC 62040-1, 2

& 3) . The UPS should be with IGBT Based Inverter Technology, Communication RS232/ RS485/ SNMP port open protocol

for BMS integration as per approved by Engineering in charge. Required battery racks, DC breaker of suitable rating and

interconnecting copper conductor cable of suitable size and connectors and all required accessories are inclusive in the cost.

6KVA UPS should have QR code which should contain drawing, test report OEM manual, Geo- Tag of manufacturing location Each 26.1.3 109793.00 1.00 109793.00 0.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

Online UPS- Input supply: Three Phase, Output supply: Three Phase. Supplying, installation, Testing & Commissioning of

following capacity at full load (Unity Power Factor) at operating temperature 0 to 40 0C, Relative humidity 0 to 95%, Online

double conversion true sine wave Uninterrupted hot swapable (allow for the replacement or addition of battery modules

without shutting down the entire system) modular Power Supply (UPS) system with N+1 modules (N denotes total number of

modules required for rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30 minutes back up

(Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup time) on full load (Battery

shall be VRLA, SMF in ABS Container) and Static Bypass switch along with provision for manual bypass, suitable isolation

transformer for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence correction. The UPS

systems offered are to be of the latest technology with Digital Control Microprocessor based for reliable operation using

Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The

quality of design, manufacturing and inspection process should confirm to the relevant Inter-national standards such as

1.39 IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while operating on battery mode and delivering 26.20

quality power to the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load.

(The required LC ( inductor (L) and a capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be

included to limit the input power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be

kva rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be

suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/-

0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non condensing, noise level less than 60db at 1 meter

distance, protections: Input Under voltage over voltage, abnormal out voltage, battery over charging, output over current,

short circuit protection, battery deep discharge protection, 10KV surge. UPS must comply with low voltage electromagnetic

compatibility (EMC) achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency Independent

(VFI)-type UPS. Communication RS232/RS485/SNMP port open protocol for BMS integration, all hardware & software for

iOT Communication

10KVA (Each Poweras per approved

shall be < Engineering

KVA) in charge. Required battery racks and interconnecting copper conductor Each 26.2.1 208893.00 1.00 208893.00 0.00

1.40 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 5.16 84.00 450.00 37800.00 0.00

Total Amount 4223780.00 197700.00

Total Amount 4223780.00 197700.00

Digitally signed by AMIT

Project Name:- Renovation/ Restoration and addition/ Alteration Interior/ Modernization of existing buildings/ facilities of ICSSR

Sr. Description Qty Unit rate Total Amount

Sr. Description Qty Unit rate Total Amount

Supply, installation, testing, and commissioning (SITC) of 12 W premium recessed

deep-eye LED downlighter, complete with driver, heat sink, and optics for seamless

false ceiling integration. Provides "dark light" effect with minimized glare and

enhanced visual comfort; beam angle 24°/36°/45° as specified; LED color

temperatures 4000K; power rating per manufacturer's specification or equivalent.

Includes all accessories, wiring up to fixture, and required painting/protection,

complete in all respects as directed by the Engineer-in-Charge (EIC).

Supply, installation, testing, and commissioning (SITC) 08 W premium recessed deep-

eye LED downlighter, complete with driver, heat sink, and optics for seamless

integration into false ceiling. Provides "dark light" effect with minimized glare and

enhanced visual comfort; beam angle 24°/36°/45° as specified; available LED color

2 temperatures 4000K; power rating per manufacturer's specification or equivalent. 26 Nos 6405 166,530.00

Includes all accessories, wiring connections up to fixture, and painting/protection as

required, complete in all respects as directed by the Engineer-in-Charge (EIC).

Supply, installation, testing, and commissioning (SITC) , premium recessed deep-eye

LED downlighter in fixture pkw/black finish, complete with driver, heat sink, and

optics for seamless false ceiling integration. Features deeply recessed light source for

"quiet" ceiling appearance with virtually eliminated glare and powerful, focused

3 illumination; available LED color temperatures 3000K/4000K/6000K; beam angle and 4 Nos 5111 20,444.00

power rating per manufacturer's specification or equivalent. Includes all accessories,

wiring connections up to fixture, and painting/protection as required, complete in all

respects as directed by the Engineer-in-Charge (EIC).

4 Supply, installation, testing, and commissioning (SITC) of professional-grade

architectural LED linear light (or equivalent), designed for continuous, shadow-free

illumination in coves, wall slots, or ceiling perimeters to create a sleek "infinity"

effect enhancing spatial volume. Complete kit including high-output LED strip and

precision-engineered diffuser for smooth, uniform light distribution without 126 Mtr 1617 203,742.00

hotspots. Includes all accessories, wiring connections up to fixture, custom

cutting/joining as required, and painting/protection, complete in all respects as

directed by the Engineer-in-Charge (EIC).

Digitally signed by AMIT

Supply, installation, testing, and commissioning (SITC) of Non-Dimmable Power

Supply, high-stability electronic driver for consistent, flicker-free power delivery to

professional LED lighting systems. Suitable for recessed downlighters, cove lights, or

linear fixtures; includes input/output wiring connections, mounting hardware, and

5 enclosure as required. Complete with protection against voltage fluctuations and 28 Nos 3817 106,876.00

short circuits, tested for compatibility, and installed per manufacturer's

specifications or Equivalent. Complete in all respects as directed by the Engineer-in-

Supply, installation, testing, and commissioning (SITC) of Laser Linear Hanging

System , high-performance 2000 mm linear pendant architectural LED light for

modern interiors requiring clean lines and precise illumination. Features sleek

minimalist aesthetic with heavy-duty construction, ideal for boardrooms, reception

6 desks, and contemporary dining areas; specialized 60° beam angle provides 3 Nos 27821 83,463.00

controlled downward "laser-like" linear task lighting with minimized spill or

equivalent, complete in all respects as directed by the Engineer-in-Charge (EIC).

Supply, installation, testing, and commissioning (SITC) versatile high-performance

linear LED lighting system with W52mm x H75mm profile for modern architectural

environments, providing bold aesthetic presence and powerful uniform illumination.

Each 1200mm unit supplied as complete "plug-and-play" system including high-

grade aluminum housing, professional LED strip, and impact-resistant diffuser for

7 seamless continuous glow or equivalent. Includes all accessories, 38 Nos 12293 467,134.00

suspension/mounting hardware, wiring connections up to fixture, custom joining for

longer runs, and painting/protection as required, complete in all respects as directed

by the Engineer-in-Charge (EIC).

8 Supply, installation, testing, and commissioning (SITC) of Magnetic Track System ,

48V DC low-voltage architectural LED track lighting rail for seamless recessed

installation creating minimalist "trimless" appearance in false ceilings. Features

magnetic technology enabling effortless movement, addition, or reconfiguration of

lighting fixtures without tools, ideal for dynamic environments such as art galleries,

high-end retail, and modern smart homes (or equivalent). Includes all track sections,

connectors, end caps, power supply integration, wiring connections up to fixtures,

and painting/protection as required, complete in all respects as directed by the

Engineer-in-Charge (EIC).

Digitally signed by AMIT

Supply, installation, testing, and commissioning (SITC) of Magnetic Laser

sophisticated track-mounted linear LED module for modern 48V magnetic rail

systems, combining "laser" sharp optics with magnetic technology for high-

performance task and accent lighting featuring minimalist low-glare aesthetic.

9 Engineered for seamless click-in connection to compatible magnetic tracks providing 30 Nos 7052 211,560.00

architectural flexibility and professional-grade light control for dynamic

environments or equivalent . Includes all necessary adapters, wiring connections up

to fixture, alignment accessories, and painting/protection as required, complete in

all respects as directed by the Engineer-in-Charge (EIC).

Supply, installation, testing, and commissioning (SITC) of "I" Connector is an

essential component for creating long, seamless runs in a magnetic track lighting

system, complete in all respects as directed by the Engineer-in-Charge (EIC).

Supply, installation, testing, and commissioning (SITC) of Power Connector, essential

component linking external power supply to 48V magnetic track systems for

seamless power distribution. Compatible with magnetic rail and linear modules,

11 ensuring stable electrical connection with proper insulation and heat dissipation. 10 Nos 1617 16,170.00

Includes mounting hardware, wiring terminations, strain relief, and protection as

required, complete in all respects as directed by the Engineer-in-Charge (EIC).

Supply, installation, testing, and commissioning (SITC) of Non-Dimmable Power

Supply , high-performance electronic driver designed to provide stable, constant

voltage to professional 48V magnetic track lighting systems. Compatible with

magnetic rails, linear modules, and associated connectors, featuring flicker-free

12 operation, overload/short-circuit protection, and efficient heat dissipation for 10 Nos 3817 38,170.00

continuous reliable performance. Includes input/output wiring connections,

mounting enclosure, compatibility testing with track system, and protection as

required, complete in all respects as directed by the Engineer-in-Charge (EIC).

Supply, installation, testing, and commissioning (SITC) of customized Skylight Ceiling

, premium interior solution using high-quality PVC film ceiling installation to mimic

natural daylight effect for LED and fabric-only applications with 120° beam angle.

Includes integrated power supply for uniform illumination or equivalent; wooden

box framing to be provided by site contractor. Complete with all accessories, edge

trims, suspension system, wiring connections up to fixtures, and painting/protection

as required, complete in all respects as directed by the Engineer-in-Charge (EIC).

Digitally signed by AMIT

Supply, installation, testing, and commissioning (SITC) of following diameter LED

chandelier , premium decorative lighting fixture featuring multiple LED light sources

arranged for elegant illumination in lobbies, reception areas, or conference rooms or

equivalent. Complete with integrated driver, suspension chain/cable (adjustable

14 height), crystal/acrylic decorative elements, and anti-corrosion finish for false ceiling 0 0.00

or direct mounting.Includes all accessories, wiring connections from ceiling rose to

fixture, safety wire backup, and painting/protection as required, complete in all

respects as directed by the Engineer-in-Charge (EIC).

Amount 2,434,065.00

Digitally signed by AMIT

Project Name:- Renovation/ Restoration and addition/ Alteration Interior/

Modernization of existing buildings/ facilities of ICSSR

S. No Description Unit Qty Rate Amount

SITC of 1 Channel Dali Gateway - interface between DALI & KNX installation.

1 Control & status data, Control of up to 1*64 DALI devices in up to 1*32 groups, Nos 2 90579.78 181159.56

Setting the colour temperature for luminaires with DALI Device Type 8 for Tunable

White in accordance with IEC 62386-209.

2 SITC of 4 Channel Phase Cut Trailing Edge Dimmer Load 180w per channel with Nos 1 84109.80 84109.80

Manual Override Button on controller

3 SITC of BUS Wired PIR, Lux, sensor on the product has a moving lens (mechanical Nos 8 21350.95 170807.58

adjustment) and a shade ring allow users to easily customize the coverage area and

detection range.

SITC of Brass/ Stainless steel brushed finish 8 button keypad (options of 1-fold/2-

fold/4-folds)offers switching, dimming, shutter, scene, value functions. Available with

4 customizable icons, RGB adaptive Backlights, proximity sensor, builtin thermostat Nos 2 41407.90 82815.80

(Built in temperature and humidity sensor) and airquality measurement (Co2levels)

with two level thresholds and poor level switching option. keyp and supports logic

functions (OR,AND,XORgates)inclusive of all materials, labour, hardware, tools,

tackles, carriage, wastageetc. as per drawings, specifications and directions of EIC.

Make- Panasonic. The device shall be in compatible with existing system installed in

PH-1 seamlessly without any third party hardware.

SITC of BUS Power Supply, 640mA Power Supply. For supplying KNX/Other Bus

devices with bus voltage. One non-choked and one choked output each. The non-

5 choked output can be used for the supply of another line or for function devices Nos 1 58229.86 58229.86

(smart sensor etc.) which require an auxiliary voltage. Nominal voltage can be

subdivided to outputs (choked or nonchoked) as desired. With reset switch for bus

lines. With short circuit protection. With overvoltage protection KNX/Other Wired

Bus only. The device shall be in compatible with existing system installed in PH-1

seamlessly without any third party hardware.

6 SITC of KNX Wire 2*2*0.8 sqmm Mtr 200 284.68 56935.86

7 SITC of DALI Wire 1.5 sq mm FRLS Mtr 400 194.10 77639.81

SITC of Automation dustribution panel with required protection devices. As per

8 actual requirement. Each Light Loop will be have Protection with MCB and Actuator/ Nos 1 58229.86 58229.86

Contactor for ISOLATION from Automation Devices.

Total Cost of Lighting Management Solutions ₹ 769,928.13

Digitally signed by AMIT

Project Name:- Renovation/ Restoration and addition/ Alteration Interior/ Modernization of existing buildings/ facilities of ICSSR

S.No. Description - Variable Refrigerant Volume System E DSR Unit DSR Rate MR rate DSR Amount

Supply, Installation, Testing and Commissioning of VRV Type Air-conditioning System with 100% Inverter Based Technology with Stepless Control Scroll Compressors with Indoor and Outdoor

1.0 Units, Induvidual.

Temperature Controller with each Indoor Unit complete with interconnected refrigerant piping with control wiring as per Standards and specifications between Indoor and Outdoor Units, full charge of

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant

Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having

100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two

compressors (with individual separate PCB) for above 14HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent,

vibration Isolators with suitable foundation etc. complete as required. To have better efficiency

condenser fan shall be capable to operate at different speed with respect to load. The unit shall

deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications

and work even at 50°C ambient temperature without tripping. The system shall be able to deliver

1.1 100% of the rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/-

10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first

charge of the refrigerant and ready for use as required. The condenser should be coated with a

hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance

water dispersion, and reduce the risk of degradation, thereby improving overall performance and

durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per

Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per

CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr

ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC

Supply, Installation, Testing and Commissioning of following minimum capacity and external

static pressure VRF/VRV ceiling mounted mid high static ductable type Indoor unit equipped with

washable synthetic media prefilter, fan section with low noise fan/dynamically balanced blower,

multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote

control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc.,

1.2 suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The

Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The

system shall be capable to adjust air flow as per room requirement automatically. The cooling

capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB

temperature. (Make will be same as of Outdoor) High Static Ductable units (minimum 49 to 77

Pascal external static pressure)

1.2.1. 3.2 Tr Ducted unit

1.2.2. 4.0 Tr Ducted unit

1.2.2. 4.6 Tr Ducted unit

Digitally signed by AMIT

Supply, Installation, Testing and Commissioning of following minimum capacity and external

static pressure VRF/VRV ceiling mounted high ductable type Indoor unit equipped with washable

synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower,

multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote

control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc.,

suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The

Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The

cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C

WB temperature. (Make will be same as of Outdoor) High Static Ductable units (minimum 78

pascal external static pressure).

1.2.1. 6.6 Tr Ducted unit

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same

Original Equipment Manufacturer (OEM) make as of ODUs and IDUs

Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air

conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper

Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto

3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/

R- 407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with

low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling,

dehumidification, air circulation of following capacity with Scroll / rotary compressor. The

4 system shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5 year 8.2.6 Nos. 2 41959.00 83918.00

Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board

(PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS

/International Electro technical Commission (IEC) 60730, hermetic compressor IS 10617, heat

exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification

and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient

temperature). Inverter Type - Hot & Cold 1.5 TR with 5 Star BEE Rating

Total Amount ₹ 1,265,242.00

Total Amount ₹ 1,265,242.00

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing

4.0 including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell

elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for

Suction and Liquid lines, all accessories as per specifications etc. as required :

4.3 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm 7.14.9 Rmt 24 1157.00 27768.00

4.4 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm 7.14.6 Rmt 26 904.00 23504.00

4.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm 7.14.5 Rmt 22 739.00 16258.00

4.6 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm 7.14.4 Rmt 72 615.00 44280.00

4.7 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm 7.14.3 Rmt 36 487.00 17532.00

4.8 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm 7.14.2 Rmt 85 346.00 29410.00

Digitally signed by AMIT

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR

5.0 PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 1.7.1 Rmt 135 370.00 49950.00

X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Supplying and installaton following size of perforated painted with powder coating M.S. cable

6.0 trays with perforation not more than 17.5%, in convenient sections, joined with connectors,

suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI

angle, bolts & nuts, painting suspenders, fastener etc as required.

6.1 300 mm width X 50 mm depth X 1.6 mm thickness 4.1.4 Rmt 55 866.00 47630.00

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

8.0 Air Distribution

Supplying, installation, balancing and commissioning of factory fabricated GSS sheet metal

rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,

8.1 vanes, hangers, supports, bends, transitions, reducers, end caps, collars etc as required complete in

all respect in confirmation to IS : 655 and approved drawings and specifications of following

sheet thickness complete as required.

8.2 SUPPLY AIR GRILL

Supplying, installation, testing and commissioning of GI volume control duct damper complete

8.2.1 with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to 30.13 Sq.mt. 4.5 7580.00 34110.00

SMACNA/IS and as per specifications complete etc. as required.

8.3 RETURN AIR GRILL

Supplying, Fixing, installation, testing and commissioning of powder coated extruded aluminium

8.3.1 Supply Air Grills with aluminium volume control dampers in confirmation to SMACNA/IS and as 30.15 Sq.mt. 2 9623.00 19246.00

per specifications complete etc. as required.

8.4 SUPPLY AIR DIFFUSERS

SSupplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but

8.4.1 without volume control dampers complete in confirmation to SMACNA/IS and as per 30.16 Sq.mt.

specifications complete etc. as required.

Supply,Installation charges of fire retardant flexible Canvas Connection between Indoor Units

and Ducts and Filters for Ducted Units

Supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed

cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for

Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile

rubber tape insulation complete as per specifications and as required.

11 Chiseling Work MR Rft 1 40.00 40.00

Digitally signed by AMIT

14 Refrigerant Charging of R410 A gas as per requirement at site. MR Kg 35 1237.00 43295.00

Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single

15 core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 2.5 sq. mm. 1.17.12 Rmt 20 148.00 2960.00

Filter value + Increase of VRV tonnage ₹ 500,000.00 500000.00

Total Value of low-site 631172.00

GRAND TOTAL VALUE ₹ 500,000.00 ₹ 1,896,414.00

GRAND TOTAL VALUE ₹ 500,000.00 ₹ 1,896,414.00

Digitally signed by AMIT

Project Name:- Renovation/ Restoration and addition/ Alteration Interior/ Modernization of existing buildings/ facilities of ICSSR

DETAILED ESTIMATE

Description Unit DSR No. DSR Rate MR Rate QtY DSR Amount MR Amount

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade

with required accessories :

i Pendent Sprinkler (Meeting Room, Lounge, Board Room etc.) Each 18.21.1 464.58 73.00 33914.34 0.00

ii Upright Sprinkler (Meeting Room, Lounge, Board Room etc.) Each 18.21.2 464.58 73.00 33914.34 0.00

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239

including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the

wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of

required shade complete as required :

1.03 Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 18.23

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI

1.04 marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 18.11

Providing, storing, handling, shifting, installation, testing and commissioning of portable fire Extinguishers as described

4.5 kg carbon dioxide extinguisher, IS marked, with high pressure discharge tube, horn, control valve, CCE approved

ii 6 kg Mono Ammonium Phosphate (ABC) type cartridge operated extinguishers Each M.R. 2315.00 7.00 0.00 16205.00

Grand total 565686.29 62325.72

Grand total 565686.29 62325.72

Digitally signed by AMIT