Special repair to Single Offrs Accn T-5 and T-71 of 1 STC Offrs Mess under GE (W) Jabalpur

Amount

Basic Rate : Refer Schedule'A' Notes

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for providing and injecting chemical emulsion for Post Constructional Anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc in apron complete all as specified and directed.

M&L for providing and injecting chemical emulsion for Post Constructional Anti-termite treatment of soil under existing floors using emulsion @ one litre per hole , 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete complete all as specified and directed.

Supply and spreading clean and dry fine sand free from sharp materials (unwashed) laying in trenches around the cable for cushioning in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable) and gently punned down to 18cm thickness complete all as specified and as directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debrise to out side MD land complete all as specified & directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete including removal of debrise to out side MD land complete all as specified & directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debrise to out side MD land complete all as specified & directed.

Hard core of stone (granite/ basalt/ trap) boulders or broken stone of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for PCC (1:5:10) type E-2 using 40 mm graded stone aggregate as in filling in sunken floor over felt etc and the like complete all as specified & directed.

M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete and sub base of floors, path/ paving etc complete all as specified & directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate in roof padding and the like etc considering the roof slope, rounded or chamfered on edge including necessary form work if required complete all as specified and directed.

PCC 1:2:4 type B-0 using 12.50mm graded stone aggregate as in bed block for hold fast, plinth courses, copings, benhing, bed plates etc and the like including weathering slightly rounded/ chamfered angles with & including necessary use and waste of form work for fair faces of concrete, complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.50mm graded stone aggregate in roof kerbs or mud stops and the like etc, rounded or chamfered on edge including necessary form work if required complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in pintle block, kerb stone, anchorage blocks, etc of size & section as per site requirement with plain fair faces, including chamfers, weatherings, throatings, etc including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed.

Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately under respective item of BOQ.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

M&L for brick work with sub class B bricks, old size straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

Cutting chases in brick walls, for concealed water tubings or conduit wiring, etc pinning in and making good as per existing, cutting exceeding 10cm but not exceeding 20cm girth complete all as specified and directed.

M&L for cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4 type B0 using 12.50mm graded stone aggregate as asked; cutting exceeding half brick but not exceeding one brick complete all as specified and directed.

Supply and laying Sub Class 'B' old size bricks laid in trenchs as cable cover all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in unframed work complete all as specified and directed.

M&L for second class (Indian Sal, Bijasal, Hollock or Benteak) hard wood in scantlings, clean sawn in unframed work complete all as specified & directed.

M&L for second class hard wood in scantlings, clean sawn in unframed work but except timber complete all as specified & directed. Note:- Old scantling as obtained from "dismantling of timber scantling" here-in-before shall be used after cleaning & stacking and quoted rate shall be deemed to be inclusive of these provisions also.

Taking down steel window or ventilator or aluminium window area n.exc 1.50 sqm each and removal complete all as specified & directed.

Taking down chowkhats or frame with shutter (w/o taking off shutter from the frame) area n.exc 1.50 sqm each and removal complete all as specified & directed.

Taking down chowkhats or frame with shutter (w/o taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

Refixing shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each in the same opening after taking down, easing and adjusting including refixing builders hardware as required and renewal of unserviceable screws complete all as specified & directed.

M&L for moulded handrails in straight length of Ist class hardwood MP teak of section 100mmx75mm including sunk to receive iron clad complete all as specified & directed.

M&L for scrolls to suit moulded handrails (dia of scroll three times width of handrail) of Ist class hardwood MP teak and fixed to handrails complete all as specified & directed.

Supply & fix factory made solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet reinforced with MS square tube and edges painted to match with printed sheet complete all as specified & directed. Make:- Sintex or Rajshri Plastiwood or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix factory made PVC door prelam frame of size 90mm x 47mm (single rebate) made out of single piece extruded (SPE) solid PVC foam profile with smooth outer integral skin throught reinforced with MS tube with PVC sheet as per manufacturer's specifications complete all as directed. Make:- Sintex or Rajshri Plastiwood or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix factory made solid PVC door frame of size 120mmx50mm made out of 5mm both side prelam PVC sheet reinforced with MS square tube and edges painted to match with printed sheet complete all as specified & directed. Make:- Sintex or Rajshri Plastiwood or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed in frame complete all as specified & directed. Make:- Sintex or Rajshri Plastiwood or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F factory made fully louvred PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, PVC sheet panel shall be louvred to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed in frame complete all as specified & directed. Make:- Sintex or Rajshri Plastiwood or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F factory made solid PVC moulded door shutter with wood free EPS (single piece extruded), 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet Polyurethane painted on the front face & 2 mm Prelam PVC sheet on back face, fixed in frame complete all as specified & directed. Make:- Sintex or Rajshri Plastiwood or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supplying & fixing in repairs, PVC kitchen shutter made out of 18mm thick PVC Ply sheet of pleasing colours, print and prelam finishes one side as approved and kitchen shutters shall be fixed to the PVC kitchen frame with & including auto hinges, steel screws and modular handels complete all as specified and directed.complete all as specified and directed. Make:- Celuca Ply of make- Rajshri or equivalent brand of make-Sintex or M/s H2O Solutions New Delhi or M/s Kumar Arch Tech Ltd as approved by GE.

Supplying & fixing 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Supplying & fixing in repairs, 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Supplying & fixing 100mm size butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized, type B-21 complete all as specified & directed.

Supplying & fixing double action spring hinges 150mm size, mild steel with steel wire spring, stove enameled, black complete all as specified & directed.

Supplying & fixing in repairs, double action spring hinges 150mm size, mild steel with steel wire spring, stove enameled, black complete all as specified & directed.

Supplying & fixing aluminium handles 150 mm size, cast type, anodised complete all as specified & directed.

Supplying & fixing in repairs aluminium handles 150 mm size, cast type, anodised complete all as specified & directed.

Supplying & fixing 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supplying & fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete all as specified & directed.

Supplying & fixing 300mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

Supplying & fixing in repairs, 300mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

Supplying & fixing in repairs, 19/20mm mild steel, chromium plated curtain rod fancy type with brackets of brass fancy type fixed on walls with brass screws complete all as specified & directed. Note:- Cost of any number of brackets shall be deemed to be included in the quoted unit rate and nothing extra shall be paid on this account.

M&L for mild steel TMT bars 10mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel conforming to Fe.290.Gde-E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work including prepration of surfaces & one shop coat of zinc chromate primer paint before fabrication complete all as specified & directed.

M&L for hold fast made out of flat iron of suitable section conforming to Fe.290.Gde-E-165 complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS:1161-1979 grade St.-240 including one shop coat painting of zinc chromate primer paint after prepration of surface before fabrication complete all as specified & directed.

M&L for mild steel plates 5mm thick or over in thickness, plain or chequered conforming to Fe- 410-W (Gde E-250) quality-A as in connecting plates etc of required size complete all as specified & directed.

M&L for rolled mild steel sections conforming to Fe- 410-W (Gde E-250) quality-A as in roof trusses (framed), main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails & guides for sliding doors, fixed with angle cleats or other connecting plates etc complete all as specified & directed.

M&L for mild steel work conforming to Fe-290 Gde -165 as in nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

M&L for 11 to 15mm dia mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 Cm but not exceeding 15 Cm long complete all as specified & directed.

S&F in repairs, stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or any other means as per site requirement complete all as specified & directed.

M&L for ornamental stainless steel tubular pipes, sheets & other sections such as pipe caps, globe etc of 18 gauge and 304 grade for staircase railing of design and pattern as approved by GE including cutting top to shape, drilling holes, notching, welding, moulding, riveting and all other necessary fittings with nut and bolts etc; and fixed to stairs complete all as specified and directed.

M&L for powder coated aluminium window sliding type (Bombey pattern) with frame of 2mm thick aluminium sections including 5.00mm thick tinted glass fixed with & including anodized aluminium snap beading, glazing clips, joining clips, screws, standard rubber gasket, handles/ Knobs two nos. for each window and MS rollers two nos. for each window shutter etc complete all as specified and directed with following specifications:- (a) Aluminium section for window frame =63.0x38.0x2mm (b) Aluminium section for styles and rails of shutter = 44.0 x18.0x2mm (c) Aluminium window frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed. Make of aluminium sections:- M/S JINDAL or M/S HINDALCO or M/S INDAL as approved by GE.

M&L for powder coated aluminium fixed type glazed ventilator with frame of 2mm thick aluminium sections including 5.00mm thick tinted glass fixed with & including anodized aluminium snap beading, glazing clips, joining clips, screws, standard rubber gasket etc complete all as specified and directed with following specifications:- (a) Aluminium section for ventilator frame =101.50x44.45x2mm (b) Aluminium ventilator frame with shutters shall be fixed in position in brick wall opening as required according to site conditions including all fastening arrangements etc complete all as specified and directed. Make of aluminium sections:- M/S JINDAL or M/S HINDALCO or M/S INDAL as approved by GE.

Supply & fix in replacement, 5.5mm thick plain sheet glass ordinary quality glazing with and including necessary rubber gasket and aluminium beads with cleats as in aluminium door/ window shutters complete all as specified and directed.

Taking down/ removing existing roof treatment over roof slab, roughening surfaces of old concrete floor/ roof/ terrace by picking and wire brushing the surface to remove the loose concrete, dust etc sweeping clean and washing down with water to remove dust, etc complete all as specified and directed.

M&L for wire brushing and clening top surfaces of tiles, lime terracing or cement concrete, including flashings and juction of parapets, etc, and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.70Kg/ Sqm, blinded with grit or pea size gravel @ 0.006 Cum per Sqm, and lightly tampered (area of flashings, etc shall be added to the roof area) complete all as specified and directed.

M&L for rendering 10mm thick in cement morter 1:3 with and including water proofing compound @ 2% by wt of cement or as per manufacturer's instructions on prepared surface of existing roof, finished even and fair complete all as specified & directed.

M&L for applying evenly tack coat of hot blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm after cleaning the surfaces over & including a coat of bitumen primer @ 0.30 litre/ sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil on the top of prepared roof surfaces complete all as specified & directed.

M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum over lap of 100mm and over lap shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.

M&L for applying a coat of bituminous aluminium paint @ 100gm/ sqm and blinding material such as dry sand @ 0.75Kg/ Sqm over & including a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer's as specified for polymeric water proofing membrane.

M&L for cutting out cracks to V section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified & directed.

Dismantling of AC (corrugated or semi corrugated etc.) sheets including ridges in roof coverings complete all as specified & directed.

Dismantling of plain or corrugated steel sheeting, any thickness including Nainital or similar pattern roof coverings complete all as specified & directed.

S&F of pre-painted galvalume aluminium zinc coating GI based 0.50mm thick corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/ L or J type or cranked hook/ bolts as complete all as specified & directed. Make: Tata Bule Scope Steel Ltd or M/S Cril Colour Roof India Ltd. or Everest Industries Ltd or equivalent brand of other Make as approved by GE from list of make attached with tender documents.

S&F of pre-painted galvalume aluminium zinc coating GI based 0.50mm thick plain steel sheet of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashings (length & girth as fixed) fixed with self tapping screws complete all as specified & directed. Make: Tata Bule Scope Steel Ltd or M/S Cril Colour Roof India Ltd. or Everest Industries Ltd or equivalent brand of other Make as approved by GE from list of make attached with tender documents.

Supply and fixed plain, galvanised mild steel sheeting 0.63mm thick with grade of zinc coating 275, in ridges, hips, valley gutters, drip and straight flashings (length & girth as fixed) in repairs complete all as specified & directed. Make: Everest or Charminar or Swastik or equivalent of other Make as approved by GE from list of make attached with tender documents.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified & directed.

M&L for bitumastic gola, with 80/25 bitumen and coarse sand mixture, 1:3 by weight, 8cm x 8cm at junction of roofing to vertical surfaces complete all as specified & directed.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified & directed.

M&L for mils steel galvanised powder coated T-grid frame work of make as approved by GE for suspended false ceiling with size of grid 600 x 600mm consisting of main tee/ runner of size 35 x 25 x 1.3 mm, cross tee of size 25 x 25 x 1.3 mm and wall angle of size 25 x 25x 1.5 mm suspended @ 1.2M c/c both way with and including 4mm dia GI wire with J hook, nuts/bolts, butterfly clips, soffit cleat/ rawl plug etc as per manufacturer's instructions and 8mm thick pre-primed, self embossed, textured designer, water & termite resistant calcium silicate boards for insulation complete all as specified and directed. Make: Armstrong or Ramco Industries or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debrise to out side MD land complete all as specified & directed.

Dismantling stone slabs and tiles/ PCC tiles of any description or thickness in floors, apron etc laid, bedded & pointed in any mortar including removal of debrise to out side MD land complete all as specified & directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.06Sqm but not exc 0.11Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11Sqm but not exc 0.18Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for glazed ceramic coloured tiles 450x300x7mm thick on vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for scratch free light shade vitrified floor tiles 10mm thick (square/ rectangular) area of each tile exc 0.36Sqm but not exc 0.42Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for scratch free light shade vitrified floor tiles 10mm thick (square/ rectangular) area of each tile exc 0.36Sqm but not exc 0.42Sqm as in skirting/ dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for 18-20mm thick granite of approved quality as in platform i.e. in horizontal & vertical position, machine cut (table rubbed and polished) laid over and including 15mm thick rendering in CM 1:4 and jointed with grey cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking plateforms, and other similar situations complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring, 18-20mm thick over & including 20mm thick cement screed bed in CM (1:6) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for machine cut kota stone slab as in skirting/ vertical surface, 18-20mm thick over & including 10mm thick rendering in CM (1:4) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for mirror/ beewax polishing to old/ existing kota stone slab floors/ skirting after grinding with machine/ manually including filling of existing joints with and including cement slurry mixed with pigment to match the shade of the slab and dusting off and washing the surfaces after grinding complete all as specified & directed. Note:- Where polishing is not possible with machine same shall be done manually.

M&L for 60mm thick rubber mould reflective factory made coloured pre cast PCC interlocking paver blocks/ tiles confirming to IS 15658-2006, M-35 designation of section as approved by GE in hard standing, laid dry over & including 25mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed. Make:- Mehtab Tiles, Indore (MP) or Nitco, Mumbai or Mayur Tiles & Interlocking pavers, Lucknow or Star Tiles & Industries, Ramadevi, Kanpur as approved by GE.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement forming joints to full depth at every 3M intervals and at every change of direction and filing with bitumen sand mixture 1:3 by weight complete all as specified and directed.

M&L for 25mm thick cement concrete type B0, 1:2:4 (using 12.50mm graded stone aggregate) in sub floors, sub-bases etc for receiving the toping layer finish the surface even & rough, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 with and including water proofing compound @ 2% by wt of cement or as per manufacturer's instructions on fair faces concrete surfaces or sunken floors, finished even and smooth without using extra cement and applying a coat of hot air blown bitumen 85/25 grade conforming to IS-702 @ 1.50 kg/sqm over newly plastered surfaces complete all as specified & directed.

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of rubbish to out side of MD land complete all as specified & directed.

Removing old lime wash (if any), hacking for key, raking out joints of old brick work or stone work built in cement or cement lime mortar; not previously plastered; and scrubbing down with water etc to receive plasterand disposal of rubbish to out side of MD land complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

M&L for 5mm thick rendering in CM 1:4 on fair faces of concrete surfaces as in ceiling, finished even and smooth without using extra cement complete all as specified & directed.

M&L for preparing new plastered surfaces of walls and applying wall putty @ 1.0Kg/ Sqm and preparation of surfaces for further treatment and applying two coats of distemper, oil emulsion white or tinted complete all as specified and directed.

M&L for preparing new plastered surface of ceiling and applying wall putty @ 1.0Kg/ Sqm and preparation of surfaces for further treatment and applying two coats of distemper, oil emulsion white or tinted complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description by complete removal of existing treatment and applying wall putty @ 1.0Kg/ Sqm and preparation of surfaces for further treatment and applying two coats of distemper, oil emulsion white or tinted complete all as specified and directed.

M&L for prepration of old decorated plastered or unplastered surface of ceiling of any description by complete removal of existing treatment and applying wall putty @ 1.0Kg/ Sqm and preparation of surfaces for further treatment and applying two coats of distemper, oil emulsion white or tinted complete all as specified and directed.

M&L for prepration of new plastered surfaces of walls and applying two coats of cement base paint over & including a coat of primer complete all as specified & directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls of any description and applying two coats of cement base paint complete all as specified & directed.

M&L for prepration of old decorated plastered or unplastered surfaces of walls & ceiling of any description by complete removal of existing treatment with steel/ fiber scrappers or any other means and applying wall putty @ 1.0Kg/ Sqm and preparation of surfaces for further treatment and applying two coats of weather proof paint (apex) over & including a coat of primer complete all as specified and directed. Make:- APEX of Asian paints or equivalent brand of other make as approved by GE.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ metal frames fixed with beads or glazed with putty complete all as specified & directed.

S&F sheet glass, ordinary quality 3.0mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in old work, serviceable beads as obtained from hacking out of sheet glass shall be re-used after cleaning/ rubbing the the same with sand paper, if required as per site. (ii) Glazing in new work, beads shall be supplied with joinery.

S&F figured glass, pin head type 3.0mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in old work, serviceable beads as obtained from hacking out of sheet glass shall be re-used after cleaning/ rubbing the the same with sand paper, if required as per site. (ii) Glazing in new work, beads shall be supplied with joinery.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat synthetic enamel paint of colour as approved by GE over and including a coat of pink primer complete all as specified & directed.

M&L for preparation of old painted surfaces of wood or wood based materials of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

M&L for preparation of surfaces of wood or wood based materials, new or old, of any description and girth, not otherwise described and treated with two coat of creosote complete all as specified & directed.

M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE over and including a coat of red-oxide primer complete all as specified & directed.

M&L for preparing new or previously untreated steel & iron surfaces of any description not exceeding 10cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coat of synthetic enamel paint of colour as approved by GE over and including a coat of red-oxide primer complete all as specified & directed.

M&L for preparation of old painted surfaces of steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) not exceeding 30cm high with synthetic enamel paint complete all as specified & directed.

M&L for marking stops, commas, short lines, dashes, hyphens, brackets, etc with synthetic enamel paint complete all as specified & directed.

Taking up or down steel tubing and connections 15mm bore including removal complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore including removal complete all as specified and directed.

Taking up or down steel tubing and connections 25mm bore including removal complete all as specified and directed.

Taking up or down steel tubing and connections 40mm bore including removal complete all as specified and directed.

Refixing old steel water tubing 15mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning and quoted rate shall be deemed to be inclusive of these provisions also.

Refixing old steel water tubing 20mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning and quoted rate shall be deemed to be inclusive of these provisions also.

Refixing old steel water tubing 25mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning and quoted rate shall be deemed to be inclusive of these provisions also.

Refixing old steel water tubing 40mm dia with and including new GI fittings and connected to new or old positions of walls, ceilings, floors etc complete all as specified and directed. Note: Old GI pipe obtained from taking up or down here-in-before shall be re-used after necessary cleaning and quoted rate shall be deemed to be inclusive of these provisions also.

Supplying and fixing 15mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supplying and fixing 20mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supplying and fixing 25mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supplying and fixing 40mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Disconnecting existing HDPE water tanks of capacity exceeding 250 litres but not exceeding 500 litres, setting aside (or lowering if required) and cleaning and removing all scale and dirt etc from water tanks and from mouth of circulating pipes and washing of tank with and including required quantity of bleaching powder etc and hoisting, if required, reconnecting and refixing in position complete all as specified & directed.

Disconnecting existing HDPE water tanks of capacity exceeding 500 litres but not exceeding 1000 litres, setting aside (or lowering if required) and cleaning and removing all scale and dirt etc from water tanks and from mouth of circulating pipes and washing of tank with and including required quantity of bleaching powder etc and hoisting, if required, reconnecting and refixing in position complete all as specified & directed.

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres and removal from site complete all as specified & directed.

Dismantling water tanks of capacity exceeding 500 litres but not exceeding 1000 litres and removal from site complete all as specified & directed.

S&F of 500 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed. Make:- Sintex or Tuff or JS Poly Plast or Dhara as approved by GE.

S&F of 1000 ltrs capacity rotational moulded polyethylene water storage tank double layered (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed. Make:- Sintex or Tuff or JS Poly Plast or Dhara as approved by GE.

Supplying & fixing 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high dencity plastic ball, screwed for iron pipe or brass ferrule complete all as specified & directed. (Note-Min weight should not be less than 210 gms) Make:- PRAYAG SYMET or COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supplying & fixing in repairs, 20mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high dencity plastic ball, screwed for iron pipe or brass ferrule complete all as specified & directed. (Note-Min weight should not be less than 210 gms) Make:- PRAYAG SYMET or COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs 15mm dia stop valves/ angle cock, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs, 15mm dia bib cock,cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down for iron pipe or brass ferrule complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs, pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm dia complete complete all as specified & directed. Make:- Marc or Zoloto or Plumber or Gem or Seiko or Prayag polymer Pvt Ltd or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supplying & fixing in repairs, 20mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. Make:- Leader or Bombay Metal & Alloy Co. or Zoloto or NMC or Vardhman or BIR Jalandhar as approved by GE.

Supplying & fixing in repairs, 25mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed. Make:- Leader or Bombay Metal & Alloy Co. or Zoloto or NMC or Vardhman or BIR Jalandhar as approved by GE.

S&F in repair, brass CP shower rose 125mm dia suitable for 15mm bore GI pipe with swivel joint as approved by GE complete all as specified and directed.

S&F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts complete all as specified & directed. Make:- PRAYAG SYMET or COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix in replacement, waste coupling of PTMT (half or full threaded) 32mm bore (minimum weight 45 gms) with and including flexible PVC waste pipe complete all as specified and directed. Make:- PRAYAG SYMET or COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs soap dish holder complete all as specified & directed. Make:- Jaquar Cat No. ACN-1131N or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs soap dispenser with glass bottle complete all as specified & directed. Make:- Jaquar Cat No. ACN-1135N or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs tumbler holder complete all as specified & directed. Make:- Jaquar Cat No. ACN-1141N or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs towel ring round with round flange complete all as specified & directed. Make:- Jaquar Cat No. ACN-1121BN or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs toilet roll holder with flap complete all as specified & directed. Make:- Jaquar Cat No. ACN-1153N or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs glass shelf 600mm long complete all as specified & directed. Make:- Jaquar Cat No. ACN-1171N or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs corner glass shelf (with bracket) complete all as specified & directed. Make:- Jaquar Cat No. ACN-1173 or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs single towel rail 600mm long complete all as specified & directed. Make:- Jaquar Cat No. ACN-1111NM or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs PVC bath cabinet with mirror of approved colour complete all as specified & directed. Make:- Prayag Cat No. 551 or equivalent model of make-COMMANDER as approved by GE.

S&F in repairs hand shower (health faucet) with 8mm dia, 1 meter long flexible tube & wall hook complete all as specified & directed. Make:- Jaquar Cat No. ALD-573 or equivalent brand & model of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs, brass chromium plated wall mixer with three joints suitable for 15mm bore pipe complete all as specified & directed. Make:- Prayag Cat No. K-7475 or equivalent model of make Marc or Gem or Plumber or Seiko or Zoloto as approved by GE.

Supply & fix in repairs vitreous china white WHB (550 x 400 mm) flat back with CP waste coupling, waste pipe, brackets including cutting for and pinning in ends of brackets complete all as specified and directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supply & fix in repairs vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) but with and including plastic water closet seat, black/ white as approved, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hinging device, complete all as specified & directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of make attached with tender documents.

S&F in repairs 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed. Make:- CERA or PARRYWARE or HINDWARE or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

S&F in repairs grating doom 100mm dia of PTMT (Minimum weight 25 gms) complete all as specified & directed. Make:- PRAYAG SYMET or COMMANDER or equivalent brand of other Make as approved by GE from list of makes attached with tender documents.

Supplying & fixing in repairs, salt glazed stoneware gully traps of size 125mmx100mm, square or round mouthed, type ‘P’ including jointing with cement mortar 1:1 complete all as specifed & directed.

Supplying & fixing in repairs, cast iron nahani trap with grating including jointing to waste pipe in run lead or solvent cement, dia of outlet 100mm complete all as specifed & directed.

Supply & fix 32mm bore, low density polyethylene pipe (LDPE) pipes, of pressure rating 6 Kg/cm2, fixed to walls, ceilings or laid in floor fixed complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or RCC) of internal dia 150mm, set in cement mortar complete all as specified and directed.

Supply, laying & joint, 160mm bore UPVC Nu-drain solid wall, socketed end drain pipes, conforming to IS:15328-2003 with & including necessary jointing matrials etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

M&L for concrete bed to drain pipes 160mm bore including packing under and haunching against the sides of pipes after they are laid and TESTED; in cement concrete 1:3:6 type C2 using 40mm graded stone aggregate complete all as specified and directed.

Supplying & fixing in repairs, 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including necessary clamps of requird size etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls/ ceiling with & including necessary clamps of requird size etc complete all as specifed & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, 110mm bore PVC (SWR) bends of any radius complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, 75mm bore PVC (SWR) bends of any radius complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, 110mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, 75mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, PVC (SWR) junction single (single T), equal or unequal, 110mm bore with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, PVC (SWR) junction single (single T), equal or unequal, 75mm bore with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, PVC (SWR) branch piece (single Y), equal or unequal, 110mm bore with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Supplying & fixing in repairs, PVC (SWR) branch piece (single Y), equal or unequal, 75mm bore with access door complete all as specified & directed. Make:- Supreme or Kisan Mouldings pvt Ltd or Finolex as approved by GE.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified & directed.

Taking down main switches/ DB's (alongwith existing board, MCBs & isolators) including removing the same from site and making good disturbed surfaces complete all as specified & directed.

Taking down existing old/ unserviceable sub main wiring of any type and description, removal of teak wood batten/ PVC pipe/ PVC casing & caping and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified and directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one light/ fan/ exhaust fan/ bell point controlled by one no one way piano type switch 5/6 Amps complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one light point controlled by two nos two way piano type switchs 5/6 Amps complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on the same board with other switches complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed solid copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

Supplying and fixing switch modular type, single pole, 6 Amps one way, 230 volts complete all as specified and directed. Make: Legrand or Crabtree (Havells) or Anchor as approved by GE.

Supplying and fixing switch modular type, 6 Amps two way ( double pole), 230 volts complete all as specified and directed. Make: Legrand or Crabtree (Havells) or Anchor as approved by GE.

Supplying and fixing socket outlet modular type, 6 Amps, 5/6 pin 230 volts complete all as specified and directed. Make: Legrand or Crabtree (Havells) or Anchor as approved by GE.

Supplying and fixing switch modular type, single pole, 16/20 Amps one way, 230 volts complete all as specified and directed. Make: Legrand or Crabtree (Havells) or Anchor as approved by GE.

Supplying and fixing socket outlet modular type, 16/20 Amps, multipurpose, 230 volts complete all as specified and directed. Make: Legrand or Crabtree (Havells) or Anchor as approved by GE.

Supplying and fixing bell push modular type, single pole, 6 Amps one way, 230 volts complete all as specified and directed. Make: Legrand or Crabtree (Havells) or Anchor as approved by GE.

Supplying and fixing rotory stepped type modular electronic fan regulator 120/ 280 Volts complete all as specified and directed. Make: Legrand or Crabtree (Havells) or Anchor as approved by GE.

Supplying & fixing ceiling rose, surface bakelite, 65x50mm surface type, two to three terminals, AC 240 volts complete all as specified & directed.

Supply and fix in replacement, electrical bell model city ding dong (Ding dong type) AC, 230 Volts complete all as specified & directed. Make:- Anchor or Cona or Plaza as approved by GE.

M&L for Provision of sub main wiring with four runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including non metallic rigid PVC conduit medium grade ISI marked not less than 25mm dia with its accessories, concealed type, including two runs of single core FRLS PVC insulated, unsheathed, solid copper conductor cable of size 4.0sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- (i) Finished sub main wiring with four runs of 6.0 sqmm cable & two runs of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, solid copper conductor cable of size 4.0sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 4.0 sqmm cable alongwith PVC conduit including its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/ copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

Supply and fix MCB DB 4 way sheet metal enclosure triple pole and neutral, IP 43 with metal door, 415 Volts with standard bus bar of suitable size and common neutral link and earth bar all enclosed on standard steel sheet flush mouting type factory fabricated complete without MCB but with enclosue blank plate complete all as specified and directed . Make:- Legrand Cat No. 5078 85 or equivalent model of make L&T/ Havells/ ABB as approved by GE.

Supply and fix MCB DB 8 way sheet metal enclosure SPN, IP 43 with metal door, 240/ 415 Volts with standard bus bar of suitable size and common neutral link and earth bar all enclosed on standard steel sheet flush mouting type factory fabricated complete all as specified and directed. Make:- Legrand Cat No. 5076 11 or equivalent model of make L&T/ Havells/ ABB as approved by GE.

Supply & fix MCB TPN, 63 Amps, 'C' series, 415 volts, 50Hz, 10kA complete all as specified & directed. Make:- Legrand Cat No. 4086 83 or equivalent model of make L&T/ Havells/ ABB as approved by GE.

Supply & fix MCB SPN, 40 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed. Make:- Legrand Cat No. 4086 18 or equivalent model of make L&T/ Havells/ ABB as approved by GE.

Supply & fix MCB SPN, 32 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed. Make:- Legrand Cat No. 4086 17 or equivalent model of make L&T/ Havells/ ABB as approved by GE.

Supply & fix MCB SP, 6 to 32 Amps, 'C' series, 240 volts, 50Hz, 10kA complete all as specified & directed. Make:- ABB or Legrand or Siemens or L&T or Havells as approved by GE.

Supplying and fixing 300mm sweep exhaust fan heavy duty of 900RPM with micro speed regulator, 220/240 volts, AC 50 Htz, air discharge 1275CMH, single phase with louvers mounting MS rag and nuts, bolts etc and fixed to wall as directed and connecting up with & including of PVC insulated and sheathed three core FRLS copper conductor flexible cable of size 16/0.20mm of sufficient length complete all as specified and directed. Make: Crompton or Havells or Khaitan or Usha or Bajaj or equivalent brand of other Make as approved by GE from list of make attached with tender documents.

Supply and fix in repairs, decorative wall light made up of high grade engineering plastic material suitable for retrofit CFL 20 W or LED lamp (sprial) with and including 14 Watt LED lamp and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells Cat Part No. LHFHCHE1TL1W020 or equivalent model of make- Philips or Crompton or WIPRO or Bajaj as approved by GE.

Supplying and fixing in repairs, indoor decorative wall light fixure made up of polycarbonate, suitable for 1x10W LED lamp (sprial B-22 base) with and including 8 Watt LED lamp and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells Cat Part No. LHDL02160099 or equivalent model of make- Philips or Crompton or WIPRO or Bajaj as approved by GE.

Supply and fix in repairs, indoor linear & compact, surface and wall mounted, 9W mirror light with decorative grey end caps, polycarbonate body and ribbed opal diffuser with and including LED lamp and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells Cat Part No. LHEXARP7PN1W009 or equivalent model of make- Philips or Crompton or WIPRO or Bajaj as approved by GE.

Supply and fix in repairs, indoor commercial basis all purpose, surface and wall mounted LED batten with polycabonate housing & integrated clectronic driver with and including 20 Watt LED tube and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells Cat Part No. LUMILINEBS20WLED830SPCWH or equivalent model of make- Philips or Crompton or WIPRO or Bajaj as approved by GE.

Supplying and fixing in repairs, 20 watt new generation energy saving and environmental friendly long life LED security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seperate driver compartment with IP65 protection and impact resistance of IK07 on bldg wall with and including pipe bracket made of G.I tubing 32/40 mm dia bore medium grade ISI marked 1.20m long bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/ MS clamps & 12mm dia bolts, nuts & washers etc including painting to all and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed. Make:- Havells Cat part No. ENDURAPEARLSL20WLED757SASYTOPC or equivalent model of make- Philips or Crompton or WIPRO or Bajaj as approved by GE.

Supplying and fixing in repairs, CIRRUS indoor commercial suspended-recessed LED office general luminaires having excellent energy savings and maintenance free operations suitable for 2'x2' grid ceiling and necessary hidden connections with & including two core copper cable of suitable size from ceiling rose to fittings complete all as specified & directed. Make:- Philips Cat part No. RC366B LED33-6500 PSU OD WH or equivalent model of make- Havells or Crompton or WIPRO or Bajaj as approved by GE.

Supplying and fixing in repairs, angle type lamp holder insulated with polycarbonate body and back plate housed with porcelain base suitable for 8Watt LED with and including 8Watt retrofit type LED complete all as specified and directed. Makes: (i) Anchor or Plaza for lamp holder as approved by GE. (ii) Crompton or Philips or Havells or WIPRO or Bajaj as approved by GE for 12Watt LED bulb.

Taking down of existing exhaust/ ceiling fan of any size/ sweep for keeping the safe cosdoy and re-fixing/ re-hanging the same after repair work or as directed and connecting up the same with & including twin twisted copper flexible wire from ceiling rose to exhaust/ ceiling fan complete all as specified & directed.

M&L for earthing complete with galvansided steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear incl 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Supplying and fixing/ laying of 40mm bore dia GI pipe medium grade in trenches/ under roads/ along pole/ wall including all necessary fittings & clamps made out of 25x3mm flat iron as required for cable protection etc after taking out existing old unserviceable GI pipe with fittings complete all as specified and directed.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 25sqmm, 4core including jointing materials such as cable glands & lugs etc after taking out the old unserviceable cable and testing on completion complete all as directed. Make:- Havells or Finolex or Gloster or Plaza or Universal as approved by GE.

Schedule of credit amount of Rs. 1,27,617.50 to be deducted during AOC

Chetna Enterprises

DEEPAK CONSTRUCTION

SHIVA ENGINEERING AND CONSTRUCTION COMPANY

M/s Shrangi Rishi Construction