PAINTING AND POLISHING / VARNISHING TO STEEL / WOODEN FURNITURE UNDER THE AOR OF GE DEOLALI

Amount

Wooden Furniture :- Material and labour for preparing of old/new polished wood based furniture articles as per the following steps:- Step 1 Sanding:- The wood components shall be rubbed with sand paper No 120 along the grains to remove any dust/ wax/unwanted stains from the surface, the sanding will be repeated with sand paper between 180-220 grit in order to achieve the smooth surface and the wood will be wiped clean with soft clean cloth complete all as specified and directed by Engr - In - Charge. Steps 2 : Staining : Any cracks or holes shall be filled with wood filler of good quality approved by Engr -In - Charge. After the wood filler has dried completly sanding with a stain of approved shade will be then applied to the prepared surface with the help of a soft malmal cloth or brush along the grain'. two to three coats of staining will be done letting the stain dry completly between each coats and sanding every time very fine grit sand paper ( 220-320) NOTE: Excess stain should be wiped off before drying and getting absorbed in wood.

Step 3 Polishing : Wood will be finished with a good quality french polish ( mixture of shellac grains and methylated spirit in ratio 1: 10) two to three coats shall be applied to prepared wood surface letting each coat to dry and absorbed fine sanding can be done if required,Polish shall be applied with a soft cloth/ brush along the grains and not against it to achieve high gloss complete all as specified and directed by Engr - In - Charge. Step 4 Varnishing : Two to three coats of Varnish shall be applied to prepared wood surface letting each coat to dry and absorbed fine sanding can be done if required,Varnish shall be applied with a soft cloth/ brush along the grains and not against it to achieve high gloss complete all as specified and directed by Engr - In - Charge. Make : Kohinoor/ wilson/Asian/Burger or equivalent as approved by GE.

Almirah Med 1/2S x 1/2 H : Drg No. DB 4232

Almirah Med w/s : Drg No. DB 3954

Almirah Large W/S : Drg No. DB 4232, DB 4116

Book Case : Drg No. FD 45, FD 237

Bin solid Linen : Drg No. FD 70

Bed W/Ply top w/o FMN FD : Drg No. FD 246/247

Chair dining : Drg No. FD - 279

Chair Easy : Drg No. FD - 229

chair writing : Drg No. FD-280/250

Chair CB W/O Arms : Drg No. DB 3972

Chair Easy Cushioned : Drg No. FD 358

Display Board 1220x 1220mm : Drg No. TP

Hat stand W/M : Drg No. FD 233

Locker Bed side P : Drg No. DB 4074

Peg Table : Drg No. FD-384/277

Rack Boot : Drg No. FD 12

Sofa Set 5 Seater : Drg No. FD-373/281 , 258

Sofa Set 4 Seater : Drg No. FD-373/281 , 258

Sofa single Chair : Drg No. FD-373

Side Board : Drg No. FD 1112, FD 241, FD 371

Table Writing : Drg No. FD-249/275

Table Writing Medium : Drg No. DB 3987, 3955

Table Dressing Gents W/M : Drg No. FD-23

Table Dressing Ladies W/M : Drg No. DB 3980, FD- 45 (M), FD 378

Table Bed Side : Drg No. FD 248, FD 276

Table dining 4 persons, 1200 mm X 900 mm X 760 mm: : Drg No. FD-273,

Table office clerk : Drg No. DB 4120

Table Office Officer : Drg No. DB 4119

Teapoy : Drg No. FD 382, DB 3675

Table Dining 6 pers : Drg No. DB 10081 / FD -273

Table Dining 8 pers : Drg No. FD -273

Table 900x 900 x 760 mm w/Dvr : Drg No. FD 291, FD 283

Table Centre : Drg No. FD 274

Table 3x2 with drawer : Drg No. FD 1008

Table 3x2 with out drawer : Drg No. FD 1007

Sofa Set 5 Seater set of (3+1+1) w/cushion : Drg No. FD/MAP-II/02

Bin solid Linen Multipurpose : Drg No. FD/MAP/06

Chair dining Map : Drg No. FD/MAP-II/05

Chair Dining Map : Drg No. FD/MAP - II/04

Table Dressing Ladies Including Stool : Drg No. FD/E6/MAP-II/07

Table Dressing Gents w/m : Drg No. FD/E6/MAP-II/18

Table dining 4 persons, 1200 mm X 900 mm X 760 mm: : Drg No. FD/MAP-II/03

Table dining 6 persons, 1500 mm X 900 mm : Drg No. FD/MAP-II/03

Wooden Furniture :- Material and labour for preparing of old/new polished wood based furniture articles of various messes and Guest Rooms as per the following steps:- Step 1 Sanding:- The wood components shall be rubbed with sand paper No 120 along the grains to remove any dust/ wax/unwanted stains from the surface, the sanding will be repeated with sand paper between 180-220 grit in order to achieve the smooth surface and the wood will be wiped clean with soft clean cloth complete all as specified and directed.

Steps 2 : Staining : Any cracks or holes shall be filled with wood filler of good quality. After the wood filler has dried completly sanding with a stain of approved shade will be then applied to the prepared surface with the help of a soft malmal cloth or brush along the grain'. two to three coats of staining will be done letting the stain dry completly between each coats and sanding every time very fine grit sand paper ( 220-320) NOTE: Excess stain should be wiped off before drying and getting absorbed in wood. Step 3 Polishing : Wood will be finished with a apporved make quality milamine polish two or three coats shall be applied to prepared wood surface by spray letting each coat to dry and absorbed fine sanding can be done if required,Polish shall be applied with a spray along the grains and not against it to achieve high gloss complete all as specified and directed by Engr - In - Charge. Make Asian Paints / Nerolac / Berger or equivalent as approved by GE.

Chair Dining W/Long Back : Drg No. FD 357

Chair Dining cushion : Drg No. FD/MAP - II/04

Chair Easy Cushioned : Drg No. FD 358

Hat stand W/M : Drg No. FD 233

Peg Table : Drg No. FD-384/277

Sofa Set 5 Seater : Drg No. FD-258, FD 281,FD 373

Sofa single Chair : Drg No. FD-373

Table Dining 6 pers : Drg No. DB 10081 / FD -273, FD/MAP-II/03

Table Dining 8 pers : Drg No. FD -273

Table Centre : Drg No. FD 274

Steel furniture :- M & L for preparing of furniture items as per following steps : (i) Denting of bent surface wih the help of hammer in best workmanship manner. (ii) Removing old paint by scubbing with sand paper 150 no throughly (iii) Applying one coat of metal primer make: asian / dulux/ nerolac. (iv) Applying metal putty to even the surface and wait period of 2-3 hours to be given for putty to set and dry completely, Scrub off the excess putty with 150 No sand paper and spreying little amount of water simultaneously. (v) Wipe the surfface with soft dry cloth and apply two coat of enamel paint by means spray painting shade as approved by Engr - In -Charge. Make Asian (Apcolite), Berger (Luxol), Shalimar (Superlac) or equivalent as approved by GE.

Almirah Large Steel w/s & w/k : Drg No. FD 67, FD 1031, FD/E6/MAP/18

Almirah Med Steel w/s & w/k : Drg No. FD 67/ FD 1031, FD 243, FD 1032, FD/E6/MAP/18

Almirah Large steel 1/2 s x1/2 H : Drg No. FD 1033

Chair CB steel with arms : Drg No. FD-75(M)

Chair CB Steel without arms : Drg No. FD-75(M)

Chair CBA spl Hand Rest : Drg No. FD 120

Chair CBA steel w/o Arms : Drg No. FD 120

Chair Varandah : Drg No. FD No-219, FD 256, FD/MAP-II/06,

Form W/Back : Drg No. FD 78 (M)

Form W/O Back : Drg No. FD 77, FD 1027

Locker Bed side steel : Drg No. FD-1029

Side Rack w/tray steel 3/4 spaces : Drg No. FD 1023

Table 3’x2’ with drawer (steel frame) : Drg No. FD 1007

Table 3' x 2' without drawer (steel frame) : Drg No. FD 1008

Teapoy Varandah : Drg No. FD 255, 383, FD/E6/MAP/17

Table Office Clerk Steel : Drg No. FD 84(M) & 1004

Table Class room steel : Drg No. FD 45, 75

Table Dining Ors w/zink top : Drg No. FD 165 (M)

Table office officer steel : Drg No. FD 84 (M), FD 1003

Chair School W/Hand Board : Drg No. FD/E6/MAP/05

Table Bed Side steel MAP : Drg No. FDE6/MAP/15 R

Bed Hard W/Ply top MAP : Drg No. FD/E6/MAP/08R

Chair Writing Steel Map : Drg No. FD/E6/MAP/12

Shoe Rack Steel : Drg No. FD/E6/MAP/02R

Charpoy W/Hard top : Drg No. FD/E6/MAP/II/01

Note: Amount of sch of credit of Rs."NIL"/-will be deducted from total amount of BOQ.

M/s National Traders

M/s Nilesh Enterprises