HOLISTIC, B/R AND E/M MAINT OF PRAYAG AND TRIVENI VIHAR IN OLD CANTT UNDER GE (EAST) PRAYAGRAJ.

Amount

Dismantling brick/ concrete tiles any size incl demolition of mud Phuska in roofs any thickness and in any position and leaping over roof terrace ,removing the demolished material to a distance exc 250 m & n exc 500 m and depositing where directed at a level n exc. 1.5 m above starting point, etc incl existing roof treatment of any thickness, complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-0, using 12.5 mm graded crushed stone aggregate for roof padding, coping , roof kerb finishing the surface fair & even, complete all as specified and directed.

M&L for 15 mm thick in CM 1:4 rendering on fair faces of concrete surfaces /roof top mixed with liquid water proofing admixture finished even and smooth without using extra cement complete all as specified and directed. Note :- Liquid WPC shall be measured and paid separately

M&L for preparation of newly plastered surfaces of roof including cleaning the surfaces by using wire brush/ pressure hose and applying high performance polyurethene liquid membrane waterproofing coating in two coats @ 1.5 Kg/Sqm/ 2 coats with spray/ brush applied, with an elongation of 300% to 700% and tensile strength of not less than 3 N/Sqmm as per ASTM D412 and ASTM D2370, crack bridging ability of 3.5mm as per ASTM C1305, shore a hardness of not less than 60 as per ASTM D2240. The item includes applying epoxy primer @ 0.15Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet, complete as per manufacturer's instructions complete all as specified and directed. Note:- (i) The contractor shall submit a guarantee of 10 years the date of completion of work for waterproofing treatment alongwith manufacturer's guarantee. The amount of Rs. 40 (Rupees Forty) per Sqm and min of Rs. 4000/- for waterproofing treatment shall be withheld from contractor's in the final bill till the expiry of guarantee period. The contractor at his own option may furnish fixed deposit receipt pledged in favour of GE against guarantee money. (ii). The water proofing shall be carried out by authorized applicator of manufacturer. The name of applicator shall be got approved from GE before commencement of work. (iii) Materials shall be procured from manufacturer/authorized dealer only and original purchase voucher for the full quantity of material shall be procured by the contractor.

M&L for Treatment to sunken floor and sides as mentioned here after:- (i) Cleaning the sunken floor surfaces with demolition and removing existing pcc ,lime conc ,muddy soil etc including taking down existing treatment to sides and base slab by using sand blasting with compressed air. (ii) M&L for application of a coat to sides and base of sunken with glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal -107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika Fab-I and top coat with Sika Seal-107@ 1.50 Kg/Sqm or equivalent of Forsoc or pidilite. (iii) M&L for 15 mm thick cement plaster on side and base slab of sunken part in cement mortar 1:3 mixed with appropriate integral water proofing compound with Sika Plastocree plus as specified. (iv) M&L for applying evenly a tack coat of industrial bitumen 85/25 @ 1.20 Kg/Sqm on plastered surface of sunken sides & base. Note:- All debris obtained from site will be thrown away out side Def Land by contractor at his own expense. (v) S&F 25 mm bore GI tube medium grade pipe spout from inside up to min 150 mm beyond outer face of the wall.

M&L for Cement concrete 1:5:10 type E2 using 40mm graded crushed stone aggregate as in sunken part of slab, complete all as specified and directed.

M&L for 25 mm thick cement concrete 1:2:4 levelling course of type B-0 (using 12.5 mm graded crushed stone aggregate) finished even & fair, complete all as specified and directed

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & including 15 mm thick screed bedding in cement mortar (1:4), complete all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and incl 10mm thick plaster in cement mortar (1:4) complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings heads, shoes, bends, swan-necks, etc., incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed, excluding fittings in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall incl necessary clamp etc, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall incl necessary clamp etc, complete all as specified and directed.

S&F 110mm PVC (SWR) bends with access door, complete all as specified and directed.

S&F 75mm PVC (SWR) bends any radius with acess door, complete all as specified and directed.

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal with acess door, complete all as specified and directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal with acess door, complete all as specified and directed.

S&F 110mm PVC (SWR) vent cowl, complete all as specified and directed.

S&F in repair 75mm PVC floor trap plain with grating including jointing with solvent cement, complete all as specified and directed.

S&F in repair Stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stage for 110mm pipe including fixing arrangement, complete all as specified and directed.

S&F in repair Stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stage for 75mm pipe including fixing arrangement, complete all as specified and directed.

M&L for cutting chases pinning in, making good to facing where reqd. and pointing in CM 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for cancealed for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth. complete all as specified & as directed

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 15mm bore pipe, complete all as specified and directed.

S&F PP-R pipe of size 20mm OD bore with 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply includingall PP-R plain & brass threaded polypropylenerandom fittings fixed complete towalls, ceilings or in floors etc., complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 20mm bore pipe, complete all as specified and directed.

S&F PP-R pipe of size 25mm OD bore with 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply includingall PP-R plain & brass threaded polypropylenerandom fittings fixed complete towalls, ceilings or in floors etc., complete all as specified and directed.

S&F in repair 15 mm size bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and directed. Make : Cera Cat Part No F2002152 or equivalent model of Parryware/Hindware

S&F in repair 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified and directed. Make :- Cera Cat Part No F8040204 or equivalent model of Parryware/Hindware

S&F in repair vitreous china wash hand basin with pedestal pattern white flat back size 550 x 400 mm excluding taps waste chain and plug but including bracket or any other fixing arrangement, waste coupling of 32 mm size fixed in repair complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat, white, closed pattern with flat bottom, and cover with aluminised hinging device, with P Trap,and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim all including all connection complete all as specified and directed. Make :- Cera Cat Part No S1053102 or equivalent model of Parryware/Hindware

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim all,complete as specified and as directed.

S&F in repair Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 330mm x 160mm, complete all as specified and directed. Make:- Neelkamal, Nirali,Blue star, Prayag or equivalent

S&F Stainless steel plate rack / utensils rack of size 900mm x 1200mm x 300mm depth made out ot 0.63mm thick stainlesss steel sheet, fixed to wall with brass screws including provision of necessary fittings / fixtures viz., nuts, bolts and washers of suitable size, the plate rack shall conform to the sample kept in sample room of AGE B/R Old Cantt, complete all as specified and directed. Make: Neelkamal, Nirali,Blue star, Prayag or equivalent

S&F Wall mixer with 115mm long Bend pipe ,connecting legs & wall Flange complete all as specified and directed.

S&F in repair 15 mm bore central hole basin mixer with 450mm braided connection pipe (without popup) complete all as specified and directed

S&F in repair Brass chromium plated shower rose 125 mm size with shower arm and fixed complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges including brackets fixed to wall, complete all as specified and directed.

S&F in repair brass chromium plated Tumbler holder all as specified as approved by Engr-in-charge,complete all as specified and directed.

S&F in repair SS soap dish complete all as specified and directed.

S&F 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete and including dismantling of old tank complete all as specified and directed.

S&F in repair PPR Gate valve for Pipe Dia 25mm OD as per Site Requirement, complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

S&F 32mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

S&F 40 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 and fittings, fixed complete to walls, ceilings or in floors etc. complete all as specified and directed.

S&F in repair 150 mm X 100 mm Salt-glazed stoneware gully traps, square or round mouthed, tvpe 'P' and setting and jointing in cement mortar 1:1 complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area not exc 1.5 Sqm each, complete all as specified and directed.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) area exc 1.5 Sqm but n exc 4.00 Sqm each, complete all as specified and directed.

S&F in repair 25 mm dia stainless steel curtain rod of 304 grade and thickness 1.25 mm for door & windows incl one pair of SS Bracket and steel cover for each rod cut to size and fixed in position complete all as specified and directed.

S&F Factory made single extruded WPC (wood polymer composite) solid door/ window/ Ceosetry windows and other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC Polymer of K value 58-60 (SUspension grade), Calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (max toxicity index of 12 for 100 gms) fabricated with mitre joints after star headed SS Screws having minimum density of 750 Kg/ cum, screw withdrawl strength of 2200 N (face) & 1100 N (edge) minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant fixed in position with MS hold fast/lugs or SS dash fasteners of required dia and length complete all as specified and directed. (MS hold fast/lugs or SS dash fasteners shall be paid for seperately) Note :- For WPC Solid door/ window frames, minus -5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimension on plus side shall be acceptable but no extra payment on this account shall be paid.

S&F factory made extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30mm comprising of virgin polymer of K value 58-60 (suspension Grade),calcium carbonate and natural fibre (wood powder / rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 Kg/cum and screw withdrawl strength of 1800 N (Face) & 900N (Edge), minimum compressive strength 50N/m2, modulus of elasticity 850N/m2 and resistance to spread of flame of class A category with property of being termite / borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of mimimum 14 microns thick of approved design pasted with hot melt addesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in Charge . Note- Stainless steel butt hinges shall be paid separately.

S&F 125x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc, complete all as specified and fixed.

S&F 105x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges lock strike plate etc complete all as specified and fixed

M&L for PCC (1:2:4) type B-1, using 20mm graded crushed stone aggregate as in bed block and filling in door frames complete all as specified as directed

S&F factory made extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (suspension Grade),calcium carbonate and natural fibre (wood powder / rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 Kg/cum and screw withdrawl strength of 1800 N (Face) & 900N (Edge), minimum compressive strength 50N/m2, modulus of elasticity 850N/m2 and resistance to spread of flame of class A category with property of being termite / borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-in Charge . Note- Stainless steel butt hinges and necessary SS screws shall be paid separately.

S&F 30mm thick plain WPC factory made glazed Skeleton door shutters (conforming as per IS-4020) with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door to be panelled with SS mosquito mesh and XTN aluminium mesh for additional strength and safety purpose. Door should be fixed with SS hinges and SS screws. Door should be water proof, termite proof, fire retardant and having screw holding capacity complete all as per manufacturers specification & drawings & as directed by Engr-in-charge. Note:- Stainless steel wire mesh shall be measured and paid separately.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F 75mm stainless steel Butt Hinges, medium weight and fixed with SS srews to door frame and shutter, complete all as specified and directed.

S&F 150mm stainless steel handles fabricated type, complete all as specified and directed.

S&F 200mm stainless steel barrel tower bolts fabricated type and fixed, complete all as speified and directed.

S&F 250mm stainless steel, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts fixed complete all as specified and directed.

S&F 100 mm long stainless steel hinges, complete all as specified and directed

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L MS Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed.

S&F Rolled Mild steel in joist, channel, angle or tee sections, fixed independently, without connecting plates (cut to ordinary lengths i.e within 20mm of the length) conforming to Fe 410-W (Gde E-250) quality A as in cooler stand, complete all as specified and directed.

M&L for Cutting holes into or through brick walls built in cement mortor superficial area n exc 150 sq cm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

S&F Powder Coated aluminium frame for doors, windows, ventilators powder coated (thickness of powder coating not less than 50 micron) with one or more rebates including jointing cleat for fixing etc complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Note:- 1. The rate is inclusive of all fixings of builders hardware such as hinges, bow handles, locking arrangements rubber beading for fixing of glass etc complete all as directed by Engr-in-Charge. 2. Glass and wiremesh shall be measured and paid separetely

M&L for 4.8 mm thick sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane, complete all as specified and as directed.

M&L for 4.8 mm thick frosted sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane, complete all as specified and as directed.

S&F 140mm Floor door stopper of aluminium alloy body and tongue, with hard drawn steel spring, complete all as specified and directed.

S&F in repair 300mm, Mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Dismantling of wooden boarding of any description fixed in any position with screws, complete all as specified and directed.

Providing and fixing 18mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white colour and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powcler/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being Termite/borer proof, water/moisture proof and Fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. Note: Stainless steel hinges shall be paid separately.

Providing and fixing 12 mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain white colour board for backing of cup boards and bathroom/kitchen cabinets etc. of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-In-Charge.

M&L for Non - skid Coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specified and directed.

M&L for Coloured Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in vertical surface, skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar 1:4 Complete all as specified and directed.

Supply & fixing 75 mm dia oval shape aluminium handle fancy type brass polished bright finish complete all as specified and directed

S&F continous (piano) hinges stainless steel bright finish of width 30 mm complete all specified and directed

S&F magnetic catcher of size 20 mm X 50 mm suitable for cupboard shutter complete all as specified and directed

Demolition of cement concrete reinforced as in chajja and similar suspended work, complete all as specified and directed.

M&L for reinforced Cement Concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in slabs supported on brick wall etc. all as specified and directed by Engineer-in-Charge.

M&L for mild steel TMT bars 10 mm dia and over in reinforcement cut to length bent to shape required incl cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L for Form work (rough finished flat ) to soffits of suspended slab such as roof slab etc not exceeding 200 mm thick complete all as specified and as directed

Demolition of brickwork built in CM,complete all as specified and directed.

M&L for brick work with sub class B bricks straight or curved on plan to any radius half brick thick wall built in CM (1: 4), complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in CM 1: 6, complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, complete all as specified and directed.

M&L for 16-18 mm thick Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in & including 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. including rounded/half rounded edge and hole for gas pipe in pre-cast slab as well as stone slab in cooking platform complete all as specified

M&L machine cut kotastone slab flooring 14-16 mm thick laid over & including 20mm thick screed bed in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L machine cut kotastone slab 14-16 mm thick in riser of steps, skirting dado and pillar laid over & including 15mm thick CM (1:4) screed bed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc complete all as specified and directed.

Taking down cement plaster on brick or stone walls or ceiling etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work in CM in 1:4 finished even and fair and mixing with water proofing liquid as per manufacturer instruction (but excluding the cost of water proofing liquid ) external surface, complete all as specified and directed.

Supply only Integral crystalline water proofing admixture of approved make, complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:6) on Brick/ Conc surface finished even and fair on internal surfaces of wall, complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on concrete surface in ceiling, complete all as specified and directed.

M&L for complete removal of existing treatment on wall/roof projections including facia, cornices etc. by manual scrapping with suitable hand tools to make surface clean, free from dust, loose paint etc., complete all as specified and directed.

M&L for 1 mm thick wall care putty and one coat of acrylic water-based exterior grade primer @0.9 ltrs (undiluted)/10 sq.mtr diluted with water in 1:1 ratio, applied manually using brush/roller, complete all as specified and directed.

M&L for two coats of water-based premium acrylic smooth exterior emulsion of approved colour with silicon additive & color stay technology, excellent dirt pick-up resistance, low VOC less than 50 g/ltr as per LEEDS specification, anti-algal properties applied in two coats @1.79 ltrs (undiluted)/10 sq.mtr diluted with water as per manufacturer’s instructions. Application to be carried out manually using brush/roller, ensuring uniform surface finish and proper penetration complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coat of oil bound distemper on walls incl 1 mm thick wall care putty, complete all as specified and directed.

M&L for preparation of old plastered surface and applying two coat of oil bound distemper on walls incl 1 mm thick wall care putty including complete removal of existing treatment, complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of ceiling and applying two coats of white wash, complete all as specified and directed.

Demolition of cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) incl chequered tiling and Paver blocks, complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in plinth protection, finishing cement concrete surface even and fair, complete all as specified and directed.

M&L Forming Contraction (Dummy)joints 65mm deep x 10mm wide,filled with sealing compound Grade A complete all as specified and directed.

Excavation in trenches n.exc 1.5 mtr wide and n. exc 1.5 mtr depth for foundation or for shafts, wells,cesspits, manholes, Pierholes etc n. exc 10 sqm on plan and n. exc 1.5 mtr in depth and getting out any type of soil complete all as specified and directed.

Providing and fixng Factory Made Precast Manhole covers of Grade M-30 Concrete complete all as specified and directed.

Supplying, laying, jointing and testing in trenches DWCPE (SN 8) nominal size in MM 163 (ID)/180 (OD) dia as per IS-16098 (Part 2) : 2013 with and including all items and activities required to make sewer line functional complete all as specified and as directed. Make :- Supreme/ Prince/Finolex.

M&L for Cleaning of HDPE tank of capacity up to & including 500 Litres by Flushing out water cleaning & removing of sludge, scale mud etc from wall & floor by rubbing with brushes, cleaning with caustic soda etc complete & finally washing with fresh water, including writing date with stencil and removing sludge, scale mud etc to a distance not exceeding 50 metre & depositing and removal of vagitation around tank area complete all as directed. Note:1. Register to be maintained by contractor with user signature after completion of work. 2. Ladder to be arranged by Contractor (rate inclusive in this item) whereever unaccessible roof is there upto a height of 12 m.

M&L for Cleaning of HDPE tank of capacity up to & including 1000 Litres by Flushing out water cleaning & removing of sludge, scale mud etc from wall & floor by rubbing with brushes, cleaning with caustic soda etc complete & finally washing with fresh water, including writing date with stencil and removing sludge, scale mud etc to a distance not exceeding 50 metre & depositing and removal of vagitation around tank area complete all as directed. Note:1. Register to be maintained by contractor with user signature after completion of work. 2. Ladder to be arranged by Contractor (rate inclusive in this item) where ever unaccessible roof is there upto a height of 12 m

M&L for Cleaning of Unaccssible Roofs/Chajjas upto 5 Storey by removing vegetation, leaves, debris, mud etc and sweeping with brushes, opening mouth of rain water pipes, etc all as directed by Engineer in Charge. Note:1. Register to be maintained by contractor with user signature after completion of work. 2. Ladder to be arranged by Contractor (rate inclusive in this item) where ever unaccessible roof is there upto a height of 12 m

Taking down carefully copper/aluminum point wiring (light/fan/socket power) complete , including fixture and fitting such as switches, ceilling roses, pendants, regulators, socket, light fittings etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per condition seperately) and making good disturbed surfaces of walls, floors, etc., complete all as specified and directed.

M&L for point wiring light/fan/bell point with PVC insulated FRLS unsheathed single core cable of multistranded copper conductor of size 1.5 sqmm as phase & neutral drawn in and including PVC conduit medium grade not less than 20 mm dia, ISI marked, duly concealed to wall/floor or above false ceiling of suitable size with all fitting and accessories laid on wall/ceiling alongwith 1.5 sqmm stranded PVC insulated FRLS unsheathed copper conductor(Green in color) as earth wire and connected to common earth dolly for the following incl making good to surface with CM(1:4) plaster and paint to match the surface complete incl provn of CI/pressed steel terminal switch box and white bakelite plastic laminated top sheet cover and fixed with brass screws cup washer for fixing switches/socket/regulators etc complete all as specified and directed for the following: - (a) one light/fan point

(b) All as per item No. 118 above but for one light point controlled by two way switches.

(c) All as per item No. 118 above but for one bell point on independent board controlled by one 5 Amps bell switch.

(d) All as per item No. 118 above but for One 5 pin 5 amps socket outlet on same board with cables of size 2.5 sqmm.

(e) All as per item No. 118 above but for One 5 pin 5 amps socket outlet on independent board with cables of size 2.5 sqmm.

(f) All as per item No. 118 above but for One 6 pin 15/16 amps socket outlet on independent board with cables of size 2.5 sqmm.

(g) All as per item No. 118 above but for one 6 pin 15/16 Amps socket outlet on independent board with cables of size 4 sqmm (for geyser point) complete.

S&F Switch Piano Flush button single pole one way 5 Amp, complete all as specified and directed.

S&F Switch Piano Flush button single pole two way 5 Amp, complete all as specified and directed.

S&F Bell Push Switch Piano Flush button single pole one way 5 Amp complete all as specified and directed

S&F socket outlet flush type 3/5 pin 5/6 Amps 230V AC complete all as specified and directed.

S&F switch piano flush single pole one way 15/16 Amps complete all as specified and directed.

S&F socket outlet flush type 5/6 pin 15/16 Amps 230V AC complete all as specified and directed.

M&L ceiling rose 3 terminal / PVC/ polycarbonate, isolated body, complete all as specified and directed.

M&L S & F stepped type electronic fan regulator flush type, complete all as specified and directed.

S&F calling bell ding dong AC 230 volts single pole complete complete all as specified and directed.

S&F Lamp holder PVC/Polycarbonate type with LED bulb 10W complete all as specified and directed.

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed.

S&F wall bracket light fancy type suitable for B-22 base holder incl 10W LED bulb complete all as specified and directed.

S&F MCB DB SPN 8 way with 200 amps 240 volts rated copper busbar in sheet steel enclosure.double door type, complete all as specified and directed.

S&F MCB , SP, AC, 240 volts of 06 to 32 Amps capacity 10KA, 'C' series and making connections with suitable size of copper lugs complete all as specified & directed.

S&F MCB, SPN, AC, 240 volts of 32 Amps capacity 10KA, 'B' series and making connections with suitable size of copper lugs complete all as specified & directed.

Taking down Ceiling fan, Exhaust fan, dismantling blades and removing fan and blades to store complete all as specified and directed. Note:- The contractor shall deposit the existing fan to store yard of AGE E/M old cantt. Quoted rates shall deemed to be included for taking down and transportation of the fans

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC), complete all as specified and directed.

Fixing only old serviceable exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan complete

S&F electric water heater, storage type steel body and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, PVC connection (02 nos) etc.complete all as specified and directed. Note:-The contractor shall deposit the existing geyser to store yard of AGE E/M old cantt

S&F LED bldg light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection with & including connecting with suitable size of copper wire complete all as specified and directed.

Disconnecting and taking out old unserviceable submain wiring and S&F sub main wiring with two single core PVC insulated,unsheathed, multistranded copper conductor cable 6 Sqmm with one single core 6 Sqmm PVC insulated, unsheathed, stranded copper conductor cable as earth wire in and including PVC conduit(HMS) of required size duly concealed to wall/floor or above false ceiling of suitable size with all fitting and accessories laid on wall/ceiling and earth wire connected to common earth point complete all as specified & directed. Note:- 2x 6 Sqm submain & 1x6 Earth wire and PVC conduit pipe shall be considered one unit length.

M&L for earthing complete with galvanished steel earth plate electrode 600x600x6.0 mm thick buried directly in ground and earth pit not less than 2.25 mtr deep below NGL and top edge of the plate not less than 1.5 Mtr deep below NGL, surrounded with adequate qty of char coal dust mixed with salt to a packed thickness not less than 15 Cm on all sides of earth plate incl excavation, earth work, returning filling in , removal of surplus soil to a distance in n.exc. 50 mtr incl GI wire 4mm dia nut bolts etc to earth plate one end connected to continuous earth wire incl 20mm GI pipe watering light grade with CI funnel, 20mm CI protection pipe medium grade and wire mesh & PCC 1:2:4 type B-1 as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1 duly re-enforced with MS bar 6mm dia @ 150mm C/C both ways with 10mm dia MS bar lifting handles, all as described in electric plate No. 3 of SSR part-I complete all as specified and directed.

M/S A P CONSTRUCTION (BID ID -3425011)

M/s DHARAM VIR GHAI (BID ID -3428306)