Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹43.7 LAccepted-AOC 8 28 BIJOYGARH P O JADAVPUR KOLKATA 700 032 | KOLKATA | WEST BENGAL | 700032 | L1 | Accepted-AOC Being a lowest bidder and reasonable | |
| 2 | L2₹46.3 L+₹1.1 L (2.33%)Rejected-Finance 8 27 BEJOYGARH JADAVPUR KOLKATA 700 032 | KOLKATA | WEST BENGAL | 700032 | L2 | Rejected-Finance Other than Lowest | |
| 3 | L3₹47.0 L+₹1.7 L (3.84%)Rejected-Finance PO CHANDL PS BISHNUPUR DIST SOUTH 24 PGS PIN 743503 | 24 PARAGANAS SOUTH | WEST BENGAL | 743503 | L3 | Rejected-Finance Other than Lowest |
Tender Value
₹40 L
EMD Value
₹80,000
Closing Date
17 Sept 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE (FW) Kolkata
D9 Commissariat Road Hastings Kolkata 700022
REPAIR TO SURFACE FINISHES, SUNKEN FLOOR GUTTERS, PANELLING AND MISC B R ITMES IN CERATIN OTM BLDGS INSIDE FORT WILLIAM UNDER GE FW KOLKATA
2022_MES_543549_2
8878/FW/E8
Open Tender
Civil Works
Item Rate
240 days
GE (FW) Kolkata
Ref tender documents
7 documents required · 7 mandatory
₹500
GE (FW) Kolkata
₹80,000
12 Nov 2022
31 Aug 2022
19 Sept 2022
31 Aug 2022
17 Sept 2022
31 Aug 2022
Amount
Chipping of unsound /weak concrete materials including cover plaster from RCC structural member i.e. slabs, beams, columns, lintel, chajja, fins, facia etc. of 50 mm average thickness (Any storey/ height of building/ structure) including tapering all edges, making square shoulders of cavities by air or sand blasting etc and cleaning of exposed concrete surface of lightly picking materials by air blasting or sand blasting including removal of foreign materials, loose concrete/aggregate etc and disposal of all debris out side of MOD land and complete all as specified and as directed by Engr-in-Charge.
Deduct / Add for below / over 5mm or part thereof thickness for item No 01 above (Any storey/ height of building/ structure)
M&L for applying chloride free rust removing chemical on rusting steel reinforcement bar as per manufacturer's specification and removing all rust from steel reinforcement bar by wire brush & sand/emery paper (after 24 hours of application of rust remover) and cleaning the area thoroughly by water with the help of pressure jet and allowing it to dry and making the reinforcement bar totally rust free (for any storey/ height of building/ structure) complete all as specified and as directed. (Make of Rust removing chemical :- Reebaklens RR of FOSROC or equivalent product other makes specified in tender) (NOTE: Surface area of cleaned steel reinforcement shall be measured for payment)
M&L for introducing new mild steel TMT reinforcement bars upto 12 mm dia for structural connection in RCC beams, columns, lintel and slabs (for any storey/ height of building/ structure) including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and up to 200mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges, plastic nozzles etc as per manufacturer's instructions etc all as specified and directed. (Make of epoxy chemical :- Lokfix E75 of FOSROC / Hilti HY 150 or equivalent product other makes specified in tender) (NOTE: Quoted rate is deemed to be inclusive of the cost of reinforcement bars)
M&L for preparation of old existing corroded and new introduced reinforcement surface (at any storey/ height of building/ structure) by brush and application of two component epoxy based zinc rich primer, of minimum specific gravity 1.75, adhesive bond strength with steel as 1.50N/mm2, as a protective coating to steel reinforcement bars in concrete with total zinc content in dry film >90% by volume and DFT per coat >50 microns complete all as specified and directed. (Make- Nitozinc primer of FOSROC or equivalent product in other makes specified in tender) (NOTE: Surface area of steel reinforcement shall be measured for payment)
M&L for applying a coat of epoxy bonding agent on existing concrete surfaces, with mixed density 1.48 Kg/litreand adhjesive bond strength>2.50 MPs, mixed and applied as per manufacturer's specifications complete all as specified and directed. (Make- Nitobond EP of FOSROC or equivalent product in other makes specified in tender) (NOTE: Measurement shall be considered for the surface area of RCC member.
M&L for applying shrinkage controlled, polymer modified, fibre reinforced cementitious repair mortar, as per manufacturers instructions to get a compressive strength of 35 MPA after 28 days, finishing surfaces even and smooth including formwork, scaffolding etc complete all as specified and directed. (Make- Rendroc SP 40 of FOSROC or equivalent product in other makes specified in tender) (NOTE: Measurement shall be considered for the surface area of RCC member.
M&L for grouting of voids/cracks with high strenth epoxy resin grout as per manufacturers instructions complete all as specified and directed. (Make- Conbexta EP 10 of FOSROC or equivalent product in other makes specified in tender) (NOTE: The item shall be executed if any voids/cracks are found during execution/removing of concrete mortar from the surface).
M&L for applying two coats of elastomeric and protective anticarbonation coating, on concrete/masonry surfacs over a coat of silane-siloxane primer as per manufacturer's instructions complete all as specified and directed. (Make- Dekguard E2000 of FOSROC or equivalent product in other makes specified in tender) (NOTE: Measurement shall be considered for the surface area of RCC member.
M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.
S& F Welded steel wire fabric n exc 4 kg per square supplied and fixed complete to wood or steel members complete all as specified and directed.
M&L for uprooting of plants or vegetation growth from wall up to roof level, applying two coats of tartaric acid and repair to broken/chipped off plastered surfaces with cement mortar 1:3 mixed with liquid water proofing compound as per manufacturer's instruction and sealed with 85/25 grade hot blown bitumen in patch not exc 2.0 sqm and removal of debris outside MOD land and disposed off complete all as specified and directed by Engineer -in charge.
M&L for repairing of damaged portion of mouth at terrace/roof surface of rain water pipe by cleaning and repairing of mouth of RWP by using cement mortar (1:3) mixed with liquid water proofing compound and sealed with 85/25 grade hot blown bitumen to mke joint of rain water pipe and roof surface fully leak proof complete all as specified and directed.
M&L for repair to chajja/projected portion, area not exc 1 sqm each by removing all broken, loose materials and repairing with cement mortar 1:3 or PCC 1:2:4 type B0 (uing 12.5 mm graded stone aggregates) on top mixed with liquid WPC as per manufacturer's instruction including benching, haunching, repair to broken plaster with dubbing coat with cement mortar 1:4 including necessary formwork complete all as specified and directed.
M&L for repair to chajja/projected portion, area exc 1 sqm but not exc 2 sqm each by removing all broken, loose materials and repairing with cement mortar 1:3 or PCC 1:2:4 type B0 (uing 12.5 mm graded stone aggregates) on top mixed with liquid WPC as per manufacturer's instruction including benching, haunching, repair to broken plaster with dubbing coat with cement mortar 1:4 including necessary formwork complete all as specified and directed.
M&L for repair to chajja/projected portion, area exc 2 sqm but not exc 4 sqm each by removing all broken, loose materials and repairing with cement mortar 1:3 or PCC 1:2:4 type B0 (uing 12.5 mm graded stone aggregates) on top mixed with liquid WPC as per manufacturer's instruction including benching, haunching, repair to broken plaster with dubbing coat with cement mortar 1:4 including necessary formwork complete all as specified and directed.
Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 150 mm thickness (above or below groud level) complete all as specified and directed.
Dismantling of floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing tiles from site and rubbish off the premises complete all as specified and directed.
M&L for plain cement concrete (1:5:10) type E2 (using 40 mm graded aggregates) in foundation filling and mass concrete complete all as specified and directed.
M&L for providing two coats of acrylic reinforced cementitious waterproof coating to prevent leakage/ seepage through sunken floor over prepared surfaces as per manufacturer's isntructions complete all as specified and directed. (MAKE: Master Seal 550 or equivalent in other makes specified in tender)
M&L for 25mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded aggregate in sub bases of floors complete all as specified and directed.
M&L Vitrified ceramic coloured (Light shade) tiles, double charged, 8 mm thick (square/ rectangular) polished, area of each tiles exc 0.42 sqm but not exc 1.28 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade laid over and incl screed bed 15mm thick cement mortar 1:4 complete all as a specified and as directed
-ditto- but light coloured double charged vitrified tiles in skirting, fixed over and incl 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.
S&F non-skid ceramic digital coloured tiles (square/ rectangular), 7 to 8 mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as per approved design, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match the shade of tiles, laid over and including screed bed 15mm thick in cement mortar 1:4 complete all as specified and directed.
-ditto- but non-skid tiles in skirting over over and including screed bed 10 mm thick in cement mortar 1:3 complete all as specified and directed.
S&F non-skid ceramic coloured tiles (square/ rectangular), 7 to 8 mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as per approved design, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match the shade of tiles, laid over and including screed bed 15mm thick in cement mortar 1:4 complete all as specified and directed.
S&F glazed coloured ceramic tiles in vertical surface, as per approved design, size 300 X 450 X 7 mm or 350 X 250 X 7 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and incl 10mm thick screed bed in cement mortar 1:3 complete all as specified and directed.
Dismantling of cast iron or reinforced concrete drain pipes, 100 mm bore, jointed in cement mortar and taking out of trenches, in required complete all as specified and directed.
Dismantling of cast iron or reinforced concrete drain pipes, 150 mm bore, jointed in cement mortar and taking out of trenches, in required complete all as specified and directed.
S&F Cast iron (sand cast) soil, waste and vent pipes 100 mm bore of any length with or without ears with cement joints all as specified laid in trenches or in floors complete all as specified and directed.
-ditto- but pipes fixed on walls
S&F Cast iron (sand cast) soil, waste and vent pipes 150 mm bore of any length with or without ears with cement joints all as specified laid in trenches or in floors complete all as specified and directed.
-ditto- but pipes fixed on walls
S&F Cast Iron Branch Piece 100mm bore (dia), single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.
S&F Cast Iron Branch Piece 100mm bore (dia) single (equal or unequal), ordinary or inverted (spigot or socket type) with Parallel Branches fitted with Oval Access Door complete all as specified and directed.
S&F CI bends for 100mm pipe (any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed.
S&F CI bends for 100mm pipe (any radius) diminishing piece or tapers (large bore measured) with Oval Access Door complete all as specified and directed.
S&F 100 mm cast iron sanitary connection socket to fit WC outlet complete all as specified and directed.
S&F 100 mm dia CI floor/nahani trap, with grating including jointing to waste pipe, fixed in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregates complete all as specified and directed.
S&F CI bends for 150 mm pipe (any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed.
S&F 150mm dia Cast iron rainwater socketed pipes with cement joints, with or without ears complete all as specified and directed.
S&F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm dia pipes complete all as specified and directed.
-ditto- but for 150mm dia of pipes
S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc including PVC seat cover complete all as specified and directed. (Make : Parryware, Model: Verve/CERA, Model: Celeb/HINDWARE, Model: Superb S) (NOTE: Cost of seat cover, hinges etc shall be deemed to be included in the quoted rate)
S&F in repair white PVC seat cover for EWC of any description with hinging device complete all as specified and directed.
S&F in repair Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type), making good disturbed Surfaces in Cement Mortar 1:3, providing CP waste coupling and PVC waste pipe and connected Items, complete all as specified and directed. (Make of WHB : PARRYWARE, Cat No. C0406 / HINDWARE, Cat No. 10010 / JAQUAR, Cat No. CNS-WHT-801 / CERA, Cat No: S2040141) (Make of Waste Pipe: PRAYAG, Cat No: 327 or equivalent make as spproved by GE) (Make of Waste Coupling: PRAYAG, Cat No: BEA-10 / JAQUAR. Cat No: ALD-705/ CERA, Cat No: F8050101)
S&F in repair 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and incl with flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed. (MAKE : PARRYWARE, Model : Slim line Economy / HINDWARE, Model : Sleek Plus / CERA, Model : Corona / PRAYAG, Model: SMART /ESSCO, Cat No: WHE-WHT-183NL)
S&F in repair Vitreous china, white, full stall urinal flat back with grating and union for discharge pipe (excl flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed. (Make of Urinal : CERA, Model: CAPRIANA / HINDWARE, Model: FLAT BACK LARGE / Jaquar, Cat No: URS-WHT-13261/PARRYWAYR, Model: New Magnum) (NOTE: Waste copupling and waste pipe shall be measured and paid seperately)
S&F in repair 38/40 mm bore PVC corrugated waste pipe, 800 mm long for wash hand basins complete all as specified and directed. (Make: PRAYAG, Cat No: 328 or equivalent make as spproved by GE)
Supply and fix in repairs Low density polyethylene pipe connection, comprising of 15 mm dia 450 mm long having PTMT union at each end of connection to end of pillar tap/cistern/stop cock/urinal etc. at one end, stop cock at other end complete all as specified and directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 or equivalent model in SHAKTI / JEXON)
S&F in repair bathroom mirror, size 600 mm x 600 mm complete all as specified and directed. (MAKE: PRAYAG, Cat No: 553 or equivalent model in POLYTUF / JEXON / SHAKTI / NILKAMAL )
S&F in repairs soap dish, chromium plated body complete all as specified and directed. (Make: PRAYAG, Cat No: BA-45 / CERA, Cat No: F5003106 / PARRYWARE, Cat No: T6902A1 / HINDWARE, Cat No: F880011)
S&F in repairs toilet paper holder, surface type with flap incl taking down existing holder complete all as specified and directed. (Make : JAQUAR, Cat No : ACN-1153N / CERA, Cat No: F5007110 / PRAYAG, Cat No: BA-08 / HINDWARE, Cat No: F880003 / PARRYWARE, Cat No: T6514A1)
S&F in repair angle valve, 15 mm bore, cast copper alloy, chromium plated fancy type, concealed type with wall flange fixed to iron pipe complete all as specified and directed. (Make : PARRYWARE, Cat No: G4807A1 / JAQUAR, Cat No: FUS-29053 / CERA, Cat No: F1015361 / ASIAN PAINTS, ALAC101 / HINDWARE, Cat No: F390005 / PRAYAG, Cat No: 9010)
S&F in repair 32 mm bore PVC corrugated waste pipe, 800 mm long for wash hand basins complete all as specified and directed. (Make: PRAYAG, Cat No: 327 or equivalent make as spproved by GE)
S&F in repair corner glass shelf 200 mm with brass brackets, as in repair complete all as specified and directed. (Make: PRAYAG, Cat No: BEA-44 / JAQUAR, Cat No: ACN-1173 / PARRYWARE, Cat No: T6010A1 / CERA, Cat No: F5005102)
S&F in repair chromium plated Hand shower (health faucet), ABS body with 1.2 metre long flexible tube in chrome finish with wall hook complete all as specified and directed. (MAKE : ESSCO, Cat No : ALE-ESS-583/ JAQUAR, Cat No: PRS-031/ CERA, Cat No: F8030401AB / ASIAN PAINTS, Cat No: C-232N / HINDWARE, Cat No: F160013 / PARRYWARE, Cat No: E8352A1)
S&F in repairs stainless steel round grating 127mm dia complete all as specified and directed. (Make : PRAYAG, Cat No: FT-64 or equivalent make as approved by GE)
S&F in repair 15mm bore chromium plated two way bib cock with flange )premium quality), fancy type complete all as specified and as directed. (Make : JAQUAR, Cat No: CON-041KN / CERA, Cat No: F1005161 / ASIAN PAINTS, Cat No: MYBC102 / PRAYAG, Cat No: 8111 / HINDWARE, Cat No: F390004 / PARRYWARE, Cat No: G1434A1)
S&F vitreous china, wall mounted closet, white incl bracket, trap, PVC soft close seat cover and connecting fittings including taking down existing water closet complete all as specified and directed. (Make : CERA, Model : COMPACT / PARRYWARE, Model: CASCADE NXT / HINDWARE, Model: STUDIO)
S&F in repair swan neck pillar cock 15mm dia chromium plated cast copper alloy with round spout, sink mounted type, screwed for iron pipe etc complete all as directed (MAKE :PARRYWARE, Cat No : G4803A1 / CERA, Cat No: F1003104 / PRAYAG, Cat No : 9014/ HINDWARE, Cat No: F280012 / ESS ESS, Cat No: PT-19 / JAQUAR, Cat No: SOL-6357)
S&F in repair Chromium plated brass Bib cock with wall flange (premium quality), fancy type, long body, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : PARRYWARE, Cat No: G4880A1 / JAQUAR, Cat No: FUS-29037 / CERA, Cat No: F1015151/ ASIAN PAINTS, Cat No: ALBC101 / PRAYAG, Cat No: 9306-N/HINDWARE, CAT No: F360004)
S&F in repairs towel rack (premium quality) with lower hangar with hook incl taking down existing rack complete all as specified and directed. (Make : JAQUAR, Cat No: AHS-1581H / ESS ESS, Cat No: AC-308 / PARRYWARE, Cat No: T6008A1 / CERA, Cat No: F5003101 / PRAYAG, Cat No: BA-12)
S&F in repair Chromium plated brass Towel ring (premium quality) complete all as specified and directed. (Make : Ess-Ess, Cat No: AC-502 / JAQUAR, Cat No: ACN-1121BN / PARRRYWARE, Cat No: T6002A1 / PRAYAG, Cat No: BA-11 )
S&F in repair 15mm bore auto closing concealed urinal flush valve with wall flange, fancy type chromium plated incl all accessories complete all as specified and directed. (Make: JAQUAR, Cat No: PRS-073 / PARRYWARE, Cat No: G2030A1 or equivalent model in CERA / HINDWARE / PRAYAG)
S&F in repair Plastic seat & cover, white, soft close type, for coupled water closet (of any description) incl chromium plated hinge complete all as specified and directed. (Make : PARRYWARE, Cat No: E8300 or equivalent model in JAQUAR / CERA / HINDWARE / PRAYAG)
M&L for providing and injecting chemical emulsion for post construction anti - termite treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.
Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars etc complete all as specified and directed.
M&L for brick work using old size fly-ash bricks straight or curved on plan exec 6 metre mean radius, built in cement mortar 1:6 complete all as specified and directed.
M&L for brick work using old size fly-ash bricks straight or curved on plan to any radius in half brick wall, built in cement mortar 1:4 complete all as specified and directed.
M&L providing cement concrete type B1 1:2:4 (20 mm graded stone aggregate) as in cills, steps, plinth course, string course, coping and other similar bands etc complete all as specified and directed.
Taking down cement plaster on brick or concrete surfaces incl racking out joints, hacking for key, scrubbing down with water etc. all as specified and directed.
M&L for dubbing out cement plaster (1:4), average 10 mm thick on irregular faces of walls (when specially ordered in writing) complete all as a specified and as directed
M&L Rendering 15mm thick, on fair faces of brick or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.
M&L 10 mm thick rendering on ceiling surfaces in cement mortar 1:3, finishing even and smooth without using extra cement including necessary scaffolding complete all as a specified and as directed
M&L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with with water proofing compound (@ 200 ml per bag of cement or as per manufacturer's instructions) on brick/stone walls or concrete surfaces finished even and fair (upto any height) for external surfaces complete all as specified and directed. (Note : Water Proofing compound shall be measured and paid separetly as "Supply only"
Supply only liquid water proofing compound, all as specified and directed.
M&L for preparation of new plastered of wall surface and applying two coats of acrylic distemper with rollers over alkali resistant primer after applying 3 mm thick wall care putty on walls, all as specified and directed.
All as per item No 78.00 but on ceiling.
M&L for preparation of new surfaces and applying three coats of white wash on walls, all as specified and directed.
All as per item No 80.00 but on ceiling.
M&L for preparation of new surfaces of walls and soffit of chajja, roof slab etc., by cleaning, brooming, rubbing and scrapping as required using broom, emery paper, putty blade/scraper as applicable to make the surface free from protrutions, loose particles, dust etc including necessary safety & protective measures such as safety belt, headgear etc, finishing the surface with 2 mm thick exterior wall putty (in two layers) for smooth finish and finishing with two coats of weather proof exterior emulsion paint over a coat of suitable exterior primer of approved make using airless spray technology capable of operating single spray gun with hose of adequate length and necessary scaffolding for upto 4 storey building height complete all as specified and directed.
M&L for applying one coat of white wash to old decorated (white washed) surfaces of wall including preparation of surfaces complete all as specified and directed.
All as per item No 83.00 but on ceiling.
M&L for preparation of old decorated plastered surfaces or un-plastered surfaces of wall and applying one coat of acrylic distemper with rollers complete all as specified and directed .
Ditto as per item No 85.00 above but on ceiling.
M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.
Ditto as per item No 87.00 above but on steel surfaces
M&L for preparation of old painted steel & iron surfaces of any description over 10 cm width or girth and applying one coat of aluminium paint complete all as specified and as directed.
M&L for preparation of old surfaces of walls and applying one coat of plastic emulsion paint with rollers, complete all as specified and directed.
M&L for applying one coat of french polishing on surfaces of any description, width or girth including cleaning and preparing the surfaces including a coat of wood filler on one or more coats on old work, all as specified and directed.
M&L for preparation of old treated/painted surfaces of walls and soffit of chajja, roof slab etc., by cleaning, brooming, rubbing and scrapping as required using broom, emery paper, putty blade/scraper as applicable to make the surface free from loose paint, algae formation, dust etc including necessary safety & protective measures such as safety belt, headgear etc including filling cracks upto 5mm with and including suitable elastomeric crackfill paste and applying one coat of weather proof exterior emulsion paint of approved make using airless spray technology capable of operating single spray gun with hose of adequate length and necessary scaffolding for upto 4 storey building height complete all as specified and directed.
-ditto- but for building from 5th to 6 storey height
M&L for complete removal of existing treatment on old painted surfaces of walls and soffit of chajja, roof slab etc. by using high pressure jet washer including cleaning the surface by scrapping as required using emery paper, putty blade/scraper as applicable for removing loose paint, corrosion, algae formation etc., to make the surface clean and free from dust, for upto 4 storey height including necessary scaffolding, safety and protective measures complete all as specified and directed.
M&L for complete removal of existing treatment on old painted surfaces of walls and soffit of chajja, roof slab etc. by scrapping and removing treated surfaces with mechanical wall sander (having vacuum mechanism for suction) having minimum 1500 RPM, sanding pad of 80 grit size having 7"- 9" dia (as required) including cleaning, watering to make the surface clean and free from dust, for upto 4 storey building height including necessary scaffolding, safety and protective measures complete all as specified and directed.
M&L for applying 2mm thick wall care putty (in two layers) on old cleaned surfaces of walls, soffits of chajja, roof slab etc, for smooth finish and finishing with two coats of weather proof exterior emulsion paint over a coat of suitable exterior primer of approved make using airless spray technology capable of operating single spray gun with hose of adequate length for upto 4 storey building height including necessary scaffolding, safety and protective measures complete all as specified and directed.
M&L preparing old surfaces of any description and applying one coat of synthetic enamel paint over brick, stone, concrete, asbestos cement surfaces or plastered surfaces complete all as directed.
M&L for preparation of old decorated plastered surfaces or un-plastered surfaces of wall and applying one coat of cement based paint with brushes complete all as specified and directed .
M&L for mirror polishing on marble/granite/kota stone work where ever equired to give high gloss finished complete all as specified and directed.
Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.
S&F for Framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0, and for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc.all as specified and directed.
Extra only over Item No. 98 above for portions framed and hung as gates, invluding pintle hinges, stops, hand made sliding bolts etc complete all as specified and directed.
M&L for applying two coats of synthetic enamel paint over a coat of Red oxide, zinc chrome primer to new steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer-in-Charge.
M&L cement concrete type C2 (1:3:6) using 40 mm graded stone aggregate, 75 mm thick as in plinth protection, laid in alternate bays, finished even and smooth without using extra cement, complete all as specified and directed.
Taking down chowkats or frames not exc 1.5 sqm each but with shutters (without taking off shutters from the frame) and removal from site complete all as specified and directed.
All as per item No 105 above but exc 1.5 sqm but n.exec 4sqm each and removal from site complete all as specified and directed.
Taking down shutters n.exc 1 sqm each and removal from site complete all as specified and directed.
All as per item No 107 above but exc 1 sqm but n.exec 2 sqm each.
M&L for Second class hardwood plain solid straight chowkats and frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and as directed.
S&F 35mm thick Factory made 2nd class hard wood glazed & skleton shutters, open rebated and prepared to received glass, gauge etc. with edges of sash bars and framing moulded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(a) complete all as specified and directed.
all as per item No. 110 above but 30 mm thick for window/ventilators etc, are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b)
all as per item No. 111 above but without sash bars
S&F factory made uPVC white color Sliding window, Two track with two panels sliding glazed with 5 mm clear float glass and one panel with stainless steel mesh size upto 1.50m height made of frame 88 x 49 mm, imbuilt fly screen track & sash 37 x 61 mm both having wall thickness varying from 2.4 to 2.8 mm and single glazing bead of appopriat dimension, comprising of uPVC multi-chambered frame with inbuilt roller track and sash extruded profiles duly reinforced with 1.50/2.50mm thick galvanized mild steel section made from roll forming process of required lenght (shape & size according to uPVC profile) appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity 40 kg), G.I. fasteners 100 x 8 mm size for fixing hardware's and drainage of water etc. after fixing frame the gape between frame and adjacent finished wall shall be fixed with weather proof silicon sealent over backer rod of requird size complete all as per specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose)
S&F factory made 35 mm thick 2nd class hard wood panelled shutters (any Nos of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density wood particle board with commercial face veneers, fitted to chowkhats complete all as specified and directed.
S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)
S&F Factory made solid PVC door frame (chowkhat) of size 100mmx45mm made out of 5mm plain colour wood grain printed PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with printed sheet reinforced with MS square tube, S&F in opening as per specification & drg as per manufacturer instructions complete all as specified and directed.
S&F Factory made solid PVC moulded door shutter, 28 to 30 m thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded prelam PVC sheet on the front face & 2 mm plain colour prelam PVC sheet on back face with particle board core, fixed in frame complete all as specified and directed.
S&F 100 mm stainless steel butt hinges (medium weight) cold rolled complete all as specified and directed.
S&F 75mm stainless steel butt hinges (medium weight) cold rolled complete all as specified and directed.
S&F 150 mm long aluminium anodised handles (cast type) ISI marked complete all as specified and directed.
S&F 125 mm long aluminium anodised handles (cast type) ISI marked complete all as specified and directed.
S&F 150 mm long aluminium anodised tower bolts extruded section, ISI marked complete all as specified and directed.
S&F 200 mm long aluminium anodised tower bolts extruded section, ISI marked complete all as specified and directed.
S&F 300mm long aluminium anodised sliding bolt with hasp, staple (bolt type) and fixing clips or sheets cast of extruded section and fixing bolts and sliding bolts of extruded section ISI marked complete all as specified and directed.
Cutting holes in to brick wall for inserting bold fast & making good dismantled portion in cm (1:3) or PCC (1:2:4) type B1, depth exceeding half brick but not exceeding 1 brick complete all as specified and directed.
M&L for mild steel bands and straps support or stays holdfast and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.
M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, treating ends of posts, back of chowkhats etc, with tar or coal tar black paint, area tarred exc 0.1 sqm but n. exc 0.5 sqm each complete all as specified and directed.
-ditto- as per Item No. 127 above above but treating small articles such as holdfasts, ends of posts, back of chowkhats, etc, area n exc 0.1 sqm each
S&F in repair floor door stopper of aluminium alloy body and tounge, anodised, with hard drawn steel spring, fixed in floor. 150mm overall length of cover plate complete all as a specified and as directed
S&F in repair floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor. 150mm overall length of cover plate complete all as a specified and as directed
S&F stainless steel wire cloth, 0.65mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as directed.
ditto - all as per item No. 131 above here-in-before, but fixed in repair.
S&F in repair Steel windows or ventilators, fixed type, complete with glazing bars devotailed or welded all as directed. (NOTE: Sheet glass will be measured and paid seperately
S&F steel window with side hung shutter including necessary hinges with steel handle and steel peg stay complete with glazing bars devotailed or welded all as directed. (NOTE: Sheet glass will be measured and paid seperately)
M&L for preparing new surface of wood or wood based material of any description and in any position not otherwise described n.exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of wood primer complete all as directed.
Hacking out old broken glass (any thickness and size or quality) from wooden frames glazed with putty or fixed with beads .
ditto - all as per item no. 136 above here-in-before, but from metal frame.
S&F 3mm thick ordinary quality plain sheet glass glass and glazing in square n.exc. 0.5 Sqm in each pane complete all as specified and directed.
S&F for sheet glass 3.00 mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.
S&F 4.80 mm thick frosted sheet glass ordinary quality and glazing with oil putty or wooden beads in square exc 0.50 Sqm in each pane complete all as specified and directed.
S&F 4.8 mm thick plain sheet glass ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane complete all as specified and directed.
S&F 25 micron sun control film on glass reflective type, best quality, sticked to glass panes as per instructions of manufacturers, complete all as specified and as directed. (Make : Garware or equivalent make as approved by GE)
S&F in repair aluminium (die cast) body door closer, hydraulically regulated designation No 3 universal type, suitable for door shutters of 851 to 1000 in width and weight between 61Kg to 80 Kg and fixed complete all as specified and directed.
S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass, other part made of mild steel heavy duty complete all as specified and directed.
S&F in repair 15mm bore galvanised steel tubing (medium grade) with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.
-ditto all as per item No 145 above here-in-before but 20 mm bore
-ditto all as per item No 145 above here-in-before but 25 mm bore
-ditto all as per item No 145 above here-in-before but 40 mm bore
S&F gun metal gate valve with iron wheel head, ISI marked, screwed both ends for iron pipe for 20 mm bore including taking out old unserviceable one complete all as specified and directed.
Ditto all as per item No. 149 above here-in before but 25mm dia of bore
Disconnecting existing water storage Tank of capacity exceeding 1000 litres but not exceeding 2000 liters for cleaning of water tank, removing of mud, sludge etc and flushing with chlorine water including S&F of any damaged accessories for water Tank and writting MES No, Unit Name (With capital letter, not exceeding 15cm height and not exceeding 10ms each tank ) and re-connecting and refixing all connections complete all as specified and directed.
Disconnecting exiting water storage Tank of capacity exceeding 500 litres but not exceeding 1000 liters for cleaning of water tank, removing of mud, sludge etc and flushing with chlorine water including S&F of any damaged accessories for water Tank and writting MES No, Unit Name (With capital letter, not exceeding 15cm height and not exceeding 10ms each tank ) and re-connecting and refixing all connections complete all as specified and directed.
Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing unsv tank complete all as specified and directed.
-ditto - all as per item No 153 above here-in-before but 2000 ltrs capacity.
S&F 25 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-153 or equivalent model in JEXON / POLYTUF / SHAKTI)
S&F 20mm dia fancy type chrominum plated dapery rod incl heavy duty decorative bracket and all fittings fixed on wall sample as approved by Engr-in-charge complete all as directed.
Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as directed.
S&F PVC solid wall lining consisting of 5 mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per manufacturer’s specification and instruction and as directed.
S&F 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing.
S&F 5 mm thick PVC decorative beading, moulded/ designed for PVC wall panneling inclusinve of fixing complete all as specified and directed.
M&L for snap grid system with powder coated aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and powder coated aluminium angle 25mm x 25mm x 1.40mm as on edges/sides, fixed to ceiling with supporting 6 mm dia. G.I hangers (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. (NOTE: Ceiling board shall be measured seperately)
Re-fixing of aluminium snap grid sytem using serviceable grid sections obtained from taking down of false ceiling, fixed to ceiling with supporting 6 mm dia. G.I hangers (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. (NOTE: Ceiling board shall be measured seperately)
S&F 'E' board "Classic", reinforced, designer series, ceiling board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium snap grid system complete all as specified and as directed.
M&L for applying one coat of acrylic distemper over suitable primer on new ceiling boards complete all as specified and directed.
S&F Suspended metal grid Ceiling System with mineral fibre acoustic tiles as per following specifications:- a) Ceiling Tiles:- Mineral fibre acoustic tile of 16mm thickness having sand textured finish with acoustical punchers, bevelled tegular edge and 8mm drop in module size of 600 x 600mm. Tiles shall have humidity reistance (RH) of 99%, NRC 0.50 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84.
(Item No. 165 Contd....) b) Metal Grid:- The grid system shall be 15 mm wide T - section flanges colour global white (matching to tile color) having roll formed double stroke rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 12.5 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 15kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”.
(Item No. 165 Contd....) All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. The ceiling grid sections shall be fixed to ceiling with 6 mm dia GI hangers upto required length by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia 40 mm long. MAKE OF CEILING GRID : ARMSTRONG, Model: SUPRAFINE 38 or equivalent in GYPROC / USG BORAL / UNISTEEL MAKE OF CEILING TILES: ARMSTRONG, Model: DUNE or equivalent item in GYPROC / USG BORAL / U TONE)
MAZUMDER ENTERPRISE
UNITED ENGINEERS
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .