Special Repairs to Floor at MT Garage in r/o MG G Area Sig Coy, P-3 (E2B) (BSO) and Provn of Standing and Parking Shed at T-2 JCO Line of GP HQ Mumbai B NCC under GE (W) Colaba, Mumbai

Amount

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) area exc 1.5 sq. m but n exc 4 sq. m each all as specifed and directed.

Dismantling of wall and ceiling boards( fibre pulp insulation etc) any thickness including cover fillets all as specifed and directed.

Taking down Chowkhats and shutters of windows/ventilators with wire mesh / glass and MS grills of any size including all fittings and fixtures all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position unframed work all as specifed and directed.

Demolition of brick masonary built in cement mortar all as specifed and directed.

Demolition of cement concrete (unreinforced below or above ground level) n.exc 15cm thick and removing rubbish to a distance n.exc 50m at low lying area all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises all as specifed and directed.

Demolition of cement concrete reinforced ( reinforcement cut as required to faciliate demolition) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, facia, fins railing, parapet etc and similar suspended work all as specifed and directed.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water and removing debris outside MD land including necessary scafolding of any height all as specifed and direcetd.

M&L in repairs to replace old decayed timber (including piecing, scarifying, etc of old and new timber if required) second class hard wood clean sawn in scantlings timber framed and fixed in any position and description including scafoldings of any height all as specified and directed.

M&L RCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in columns, foundations, beams, slabs, parapet, staircase including demolition all as specified and as directed by Engr-in-Charge.

Use and waste special water tight centering and shuttering including bolting, strutting, propping etc. so as to withstand a pressure of 0.1 Mpa including removal of form work of all locations including beams, columns, slabs, walls, foundations, footings, landings, stairs, balconies all as specified and as directed by Engr-in-Charge.

M&L 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection, flooring/subbase including necessary shuttering all as specified and directed.

M&L 100 mm thick READY MIXED CEMENT CONCRETE DELIVERED ON BUNKER M-20 type 1, 1:11/2:3 (using 20 mm graded crushed stone aggregate) as in flooring and all other similar works all as specified and directed.

M&L forming construction (Dummy) joints 65 mm deep 10 mm wide, filled with sealing compound grade 'A' all as specified and directed.

M&L in repairs RCC 1:2: 4, type B-1 (using 20 mm graded crushed stone aggregate) as in columns, foundations, beams, slabs, parapet, staircase all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape, required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as specified and directed.

All as per item no 17 above but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders

M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 as specified and directed.

M&L broken stone or boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface using power roller all a specified and directed by Engr-in-charge.

M&L PCC 1:4:8 type D2 (using 100mm graded crushed stone aggregate) and similar work all as specified and directed.

M&L earth filling in floors etc., spreading and leveling in layers, well ramming including watering as required all as specified and directed.

M&L 75mm thick cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in floors, plinth protection (finished even and fair) laid in panels including joints filled with sealing compound grade 'A' all as directed by Engr-in-Charge

M&L in repairs coloured double charged digital glazed vitrified tiles 10 mm thick (Square/rectangular) polished area of each tile exc 0.36 Sqm but not exc 0.72 Sqm in vertical surfaces such as skirting & dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles as specified and directed.

M&L in repairs coloured polished digital vitrified tiles 10 mm thick (Square/rectangular) polished, area of each tile not exc 0.36 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles as specified and directed.

M&L coloured, digital glossy/Matt outdoor elevation ceramic tiles in vertical surfaces 600x300x7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles all as specified and directed.

M&L for any coloured digital ultra strong / heavy duty outdoor anti skid vitrified tiles 15-18 mm thick (Square / Rectangular, 600mm x 600 mm) polished, area of each tile exc 0.09 Sqm and not exc 0.36 sqm, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles and including 20 mm thick in cement plaster in CM (1:4) for fixing tiles any where all as specified and directed.

M&L coloured, digital glazed ceramic tiles in vertical surface 600x300x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of the tiles including 10 mm thick rendering in CM 1:4 all as specified and directed. Note:- Rate of Designer border in vertical surface will be deemed into quoted rates.

M&L Granite (of any type and colour) 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid in floors/Jambs/WHB conters and all other similar works in approved design laid over 20 mm thick screed bed in CM 1:4 all as specified and directed.

M&L Machine cut cudappah stone slab 20-25mm thick including 20 mm thick cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing all as specified and directed.

M&L Hard drawn steel welded wire fabric mesh, 100 x 100 x 3mm dia cut to lengths bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia anchored over 3 to 4 inch long iron nails at a distance of 0.6 m in both direction and fixed in walls / reinforcemnt weight not less than 1.37 Kg/Sqm but not exc 4kg per sqm for fixing and for bracing, supporting or otherwise holding firmly in position so that the placing and ramming of concrete will not displace it. The rates includes for straightening, raking or circular cutting and waste. Rates also include for straightening where reinforcement is supplied in rolls/coil.

S&F in repairs SS 304 Grade metal letters of height 200mm with PU paint to match the logo colours, mirror polished finish, anti rust and including necesssary arrangements to fixing in walls, using scaffolding at any height all as specified and directed.

S&F in repairs sign board made of retro reflective Type IV high intensity prismatic grade sheeting in any colour and size with signs as per IRC 67-2012 and 3 mm aluminium compsoite material grade including required clamps, embedded in above ground level with written name of officers on board and making good surface all as specified and directed.

S&F in repairs 3 mm thick panel of any type, pattern and shape Aluminium Composite Panel (ACP), aluminium thickness of 0.5mm, Front side finish of aluminum roll coated with Plain / coloured / wooden texture PE / PVDF, Core material of Non-toxic polyethylene, Macromolecular lamination film, Rear side of Aluminum coated with primer and including frame work using of Fasteners, including concealed screws, nuts, bolts and other items required for connecting aluminium to aluminium / steel / wooden / ply board, Blind rivets all fixing anchors, brackets and similar attachments used in the erections, shall be of aluminium, non-magnetic stainless steel, zinc coated steel, for fixing in both internal / external wall cladding complete weather proofing sealant of a polyurethane elastic joint / structural silicone sealant / pre-formed gaskets to the Horizontal & Vertical Joints in the Aluminium cladding / facade as per manufacturer's instructions all as specified and directed. Note : 1. The unit rate quoted is deemed to be inclusive of all necessary fixing acceserries mentioned in the description of work and scaffolding works at any height for installation. 2. For payment purpose panels areas will be measured on one side only.

Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water as specified and directed.

M&L for two coats of oil bound distemper over 1 mm thick wall care putty on new plastered surfaces including preparation of surface as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surface all as specified & directed.

M&L for 12 mm thick ready mix plaster in single layer on brick wall or concrete surfaces including making groove of appropriate size, on other than fair faces of concrete/brick surfaces (internal surface) and finished surfaces even & smooth with out using extra cement all as specified & directed.

M&L for 20-25 mm average thick Ready Mix Plaster in multi layer, mixed with liquid water proofing compound on other than fair faces all as specified & directed.

Supply only integral waterproofing compound

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as specified & directed.

M&L for preparation of newly plastered wall surfaces and applying a coat of wall care putty (Birla White Wall care or equivalent) 2mm thick ( in two coat 1 mm thick each coat )avg on plastered surfaces rubbing with sand paper, preparatory to distempering and applying two coats of acryilic emulsuion over a coat of alkali resistant priming paint all as specified and directed.

Taking down Chowkhats and shutters of windows/ventilators with wire mesh / glass and MS grills of any size including all fittings and fixtures all as specified and directed.

M&L for 5.5 mm thick sheet glass, ordinary quality and glazing with aluminium beads and rubber gaskit in square area exc 0.5 sqm in each pane frosted on one side all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making, provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete as per architectural drawings and the directions of Engineer-in-Charge. Note : (i) Glass panes will be measured & paid separately (ii) The quoted rate shall be inclusive of cost of rubber beading and glazing clips, hionges, handle. However it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.

S&F Aluminium deco grill Cat No DG-916, 7.5 mm thick, cut to required size/shape and fixed in position with aluminium beading all as specified and directed.

S&F sheet glass, ordinary quality, 5.5 mm thick, plain or frosted on one side and glazed with oil putty or fixed with rubber beading in square exc 0.5 Sqm in each pane or as required all as specified and directed.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm of approved design and fixed with aluminium windows all as specified and directed.

S&F in repairs 12mm thick, toughened glass for door shutters, partitions in bathroom or other places, shelves, table top etc and in similar work with and including fitting and fixtures such as glass handles SS studs, fittings for door pivots all as specified and directed.

S&F Sun control film, 50 micron non reflective type, sticked to glass as per manufacturers instructions all as specified and directed.

S&F in repairs SS 202 Stain finish Handle D type, 25mm dia 600mm long for glass shutter all as specified and directed

S&F in repairs bottom/top patch fitting for pivot all as specified and directed

S&F in repairs bottom lock patch fitting all as specified and directed

M&L for 10 mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface with GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre with & incl Hangers 4mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long all as specified and directed.

Extra over above items no.54 above but for any sunk or raised moulding complete all as specified and directed.

S&F GI powder coated frame work for seamless ceiling 600x600mm grid size comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre all as specified and directed.

S&F 8 mm thick exposed metal frame ceiling with calcium silicate board of siliceous and calcareous materials reinforced with cellulose fibre for fixing in 605 X 605 mm grids all as specified and directed. Note:- Frame work for ceiling shall be measured and paid separately.)

M&L 8/10 mm thick PVC ceiling or wall panelling (any colour) with aluminium frame work for receiving ceiling board / wall panelling including all necessary accessories for fixing at various levels all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat comprising of 50 mm X100 mm size applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold unserviceable fast/lugs/SS dash fasteners of required dia and length all as specified and as directed by Engr-in-Charge

S&F 40 mm thick flush shutters, solid core construction, with block board core and ply wood face panels, both faces is covered with decorative face Laminate both side with incl 5mm thick teakwood lipping all around / frame to match on both side with supply & fixing stainless steel 7.5 inch Mortice 7 lever door lock, double action with handle all as specified & directed.

S&F 35mm thick flush shutter, solid core construction with block board core and one side laminate and one side with different colours matt finish of wooden colour solid panel decorative type on both side all as specified and directed.

M&L for preparation of new wood or wood based surfaces, of any description, not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

S&F aluminium anodised 100 mm barrel tower bolts of extruded section all as specified and directed.

S&F aluminium anodised 200 mm barrel tower bolts of extruded section all as specified and directed.

S&F aluminium handle 150 mm cast type anodised fixed complete all as specified & directed

S&F 100 mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 all as specified and directed.

S&F 200mm size brass handle cast type polished bright all as specified and directed.

S&F 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled of drawn brass bolts all as specified and directed.

S&F aluminium anodised Barrel tower bolts of extruded section, length of bolt 300mm all as specified and directed.

S&F door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring of size 150 mm all as specified & directed .

S&F in repairs 25 mm dia stainless steel decorative type curtain rods to be fitted with stainless steel bracket and all other connected works all as specified and directed,

S&F stainless steel side brackets of approved quality all as specifed and directed.

Providing and injecting chemical emulsion using chlorpyriphos 20 percent EC with 1 percent concentartion for post constructional Anti-termite treatment along external wall below concrete or masonary apron using chemical emulsion at the rate of 2.25 litres per linear metre including drilling and plugging holes etc in apron all as specified and directed.

S&F for joist channel, angle or tee section fixed independently without connecting plate etc (cut to ordinary length i.e with in ) confirming to Fe 410 -W (Gde- E- 250) quality- A incl welding, nuts and bolts all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer using ERW or induction butt welded tubes, nuts and bolts, welding conforming to IS 1161-1979 grade St-240

S&F rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 -W (Gde- E- 250) quality A complete all as specified & directed .

Dismantling of wrought iron or mild steel work of any description not otherwise provided for all as specified and directed.

M&L framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165 all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar patteren roof coverings including scafoldings of any height all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, eaves etc fixed with self tapping screws all as specified and directed.

M&L two coats of synthetic enamel paint over a coat of red oxide on steel surfaces including preparation of steel surfaces width or girth exc 10cm all as specified and directed.

S&F mild steel work using flat iron as in stays for rainwater, ventilating pipes, rain water half round brackets including bolts if required and similar small articles conforming to Fe410-0 or Fe 310-0 all as specified and directed.

S&F rain water gutter in half round shape 110mm dia PVC ( SWR) grade pipes single socketed in any length with integral outlet of 110 mm dia all as specified and directed

S&F PVC (SWR), 110mm bore, Double socketed in any length with rubber ring joints, fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, any location, any floor including necessary scaffolding all as specified and directed.

S&F 110mm dia PVC (SWR) bends /elbow any radius including GI clamps of approved shape and size approved by GE at any height, any location, any floor including necessary scaffolding all as specified and directed.

S&F aluminium (Die cast) body, door closer, hydraulically regulated, designation No. 3, unversal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg all as specifed & directed.

S&F sinks made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 510mm x 510mm bowl size 460mm x 460 x 230mm all as specified and directed.

S&F 15 mm bore fancy type sink cock (wall mounted) with 150mm (6") long swivel spout, wall flange and provision for WP connection, cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

S&F in repairs GI tubing 15 mm bore medium grade with all fittings as IS 1239 (PART 1) : 2004 and fixed complete to wall and ceiling or laid in floors all as specified and directed.

S&F in PVC (SWR) floor trap 75 mm, plain with CP grating including joining and solvent cement all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft loose soil all as specified and directed.

M&L PCC 1:4:8, type D2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete all as specified and directed.

M&L PCC 1:2:4, type B2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete all as specified and directed.

M&L for crushed sand filling under precast interlocking paver blocks and all other similar works all as specified and directed.

M&L rubber moulded glossy finished precast concrete interlocking paver block of any shape and size confirming to IS 15658 -2006 of 60 mm thickness, M-40 Grade laid over sand cushning including compaction of paver blocks using surface vibrator all as specified and directed. Note :- Sand cushioning shall be paid separately under relevant item.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm in hard/dense soil all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust & brushing neat cement slurry with 3.0 kg of cement per sq mtr all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm thick laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to mirror finish inluding Screed bed or bedding layer of mortar 15 mm thick in (1:6) for laying floor finishes all as specified and directed.

All as per item no 99 above but in riser of steps, skirting, dado and pillar laid over cement screed and jointed over rendering 10 mm thick on fair faces of brick work in CM (1:4) all as specified and directed.

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and to deposit all item to CSD store yard or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling all as specified and directed.

M&L for Point wiring (concealed type) with 1.5 sq mm, PVC insulated unsheathed (FRLSH), 1100 volts grade, multi-stranded copper conductor, in and including rigid non-metallic PVC heavy duty conduit (ISI mark), 19/ 20 mm dia suitable size including cutting chases for conduits, sinking for concealed boxes and for concealed conduit wiring with all fittings and accessories including modular cover plates as required with and fix conecaled 1.2 mm thick pressed steel modular sunken box, suitable for fixing moduler switch socket and unsheathed (FRLSH) single core multi-stranded copper conductor cable of size 1.5 sq mm green in colour as earth continuity conductor connected to common earth dolly and making good to the disturbed surfaces to match with the existing surfaces complete (fill up cement in gaps, finishing with putty and apply two coats of paint, match with existing colour in disturbed surface area), as per IS specification and as specified in SSR Part-I complete for one light point controlled by one modular switch, 1 way 6/10 amps, 1 module.

All as per Srl item No.102 here in before but for socket outlet point 5 Amp on same board.

All as per Srl item No.102 here in before but for socket outlet point 5 Amp on Independent board.

All as per Srl item No.102 here in before but with 4 sqmm cable for 3 pin 15 Amps switch socket outlet (Power point)

S&F modular switch 1 way 6 A module 230/250 volt, AC supply, ISI Marked, with white cover plate with frame all as specified and directed.

S&F modular switch 1 way 16 A module 230/250 volt , AC supply, ISI Marked, with white cover plate with frame all as specified and directed.

S&F modular sockets 6A 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with cover plate all as specified and directed.

S&F modular sockets 6A/16A, 2/3 pin combined 2 module 230/250 Volts, 50 Hz , AC supply, ISI Marked, with white cover plate with frame all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet all as specified and directed.

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal all as specified and directed.

S&F LED light fitting 1x9W/1X10W luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed.

S&F LED Batten lights fitting 1x 20W, 220V, AC decorative box type, warm white / white type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete pre wired fixed to wall with 2 nos PVC block of suitable size all spcifided and directed. Note: Connection should be made neatly using two core flexible cable.

S&F in repairs MCB Distribution board, 240 volts single pole and neutral, double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down all as specified and directed.

S&F Exhaust fan 230 volts, 250mm, metal heavy duty with wooden frame including making all electric connection all as specified and as directed including cutting of hole on wall and makng good disturbed surface of wall and outer wooden box for fan fix on wall all as specified and directed.

M&L refixing of ceiling fan (old fan) and connecting up including provision of cable from ceiling rose or connector and fan Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. with taking down fan, sealing cable end, dismantling romoving and hanging fan and blades and removing fan and blades to store all as specified and directed. .

S&F Ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC making all electric connection. huck and suitable size rod for hanging ceiling fan all as specified and as directed

S&F in repairs Slim desingn LED recessed square 2X 2, 36 watt Warm/ white type flat panel PDC aluminium housing and PMMA diffuser including taking down old unserviceable one all as directed and specified

S&F LED security Building light LED 45 Watt, pressure die cast aluminum housing, heat resistant glass, IP65/66 protection, better optics for uniform distribtion complete with all accessories internally pre wired and including connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light all as specified and directed. Note: Rate quoted should be inclusive of 3 Core flexible cable.

S&F in repairs MCB Distribution board, 240 volts single pole and neutral, single door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways, fixed on wall duly grouted in solid block wall or on wooden board with electrical connection, including taking down all as specified and directed.

S&F in repairs MCB DP, 240 Volts, 40 Amps, 10 kA rupturing capacity 'C' series all as specified and directed

S&F in repairs MCB, single pole 240 volts 6 to 32 Amps capacity fixed in DB's all as specified and directed.

Supplying, laying, commissioning & testing in repairs LT underground cables 10 Sqmm X 3 Core, 1100 Volts grade, XLPE insulated, PVC sheathed heavy duty, armoured with multi-stranded aluminium conductor all as per IS 7098 (Part -1) laid in trenches, ducts, drawn through pipes or fixed on poles, as and when required all as specified and directed. Note : Rate inclusive of aluminium Lugs and furrowl used in cable connection.

S&F in repairs MCCB DB TPN 4 way vertical sheet metal enclosure TPN 415 volts, 50 Hz, with IP-43 protection, single door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting all as specified and directed. Note : MCB SP/TPN shall be measured and paid seperately under appropriate items of this schedule . Note : Copper thimble shall be used for connection of cable .

S&F in repairs MCCB TPN, 240 Volts, 63 to 100 Amps, 10 kA rupturing capacity 415 Volts all as specified and directed.

M&L in repairs Sub main wiring with two run of 6 sq mm stranded copper conductor PVC unsheathed FRLSH wire along with 6 sq mm green colour wire as earth contuinity conductor connected to common earth dolly including PVC FR heavy duty conduit of adequate size (not less than 32 mm dia) for housing the wires for from Pannel / Main DB to house SPN DB all as specified & as directed by engr-in-charge Note: Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. Note: Mode of measurement two runs of 6 sqmm cable and one run of 6 sqmm cable with PVC conduite shall be measured as one length.

M & L Sub main wiring with two run of single core 4 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia Cassing capping ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 4 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion inculding taking down old wiring etc complete all as directed.Note: (i) Two runs of 6 sqmm and one run of 6 sqmm cable and one run of PVC conduit shall be measured as one RM.

M&L in repairs Sub main wiring with two run of single core 1.5 Sqmm FRLSH copper conductor cable PVC insulated, unsheathed, 1100 V including 20 mm dia Casing cappiing ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall along with one run of 1.5 Sqmm single core PVC FRLSH insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion all as specified and directed. Note: (i) Two runs of 1.5 sqmm and one run of 1.5 sqmm cable and one run of PVC conduit shall be measured as one RM.

M&L earthing complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers, galvanised steel and protected by GI pipe 15 mm bore light grade & connected to main switch board or main control board as directed and including concrete pit in PCC (1:3:6) type C1, precast RCC (1:2:4) type B1 cover slab 30 cm X 30 cmX 5 cm with 10mm dia TMT bars 8 cm C/c both ways and one handle for lifting made out of 8 mm dia TMT bar, funnel, wire mesh, 20mm bore galvanised iron pipe (medium grade) for watering, charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil and including necessary testing on completion all as shown in Electrical Plate No 3 of SSR part -I.

SAHU AND SAHU CO. (BID ID -3250917)

N F ENTERPRISES (BID ID -3244732)

Unitech Enterprises (BID ID -3241047)

Shivam Enterprises (BID ID -3244484)

GUPTA ENTERPRISES (BID ID -3243515)

SAHI SAGAR ENTERPRISES (BID ID -3241679)

Nilesh Construction (BID ID -3250384)

GANGAJAL (BID ID -3242623)

Bidder Name

Unitech Enterprises

Frends Enterprises

Nilesh Construction

SAHU AND SAHU CO.

GANGAJAL

Shivam Enterprises

SAHI SAGAR ENTERPRISES

N F ENTERPRISES

GUPTA ENTERPRISES