Improvements to the Sub Health Centre at Karukkankudy, Karaikal.

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms , lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , withina lead of 50m -All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50m and lift upto 1.5m.

Supplying and filling in plinth with river sand under floors including, watering, ramming consolidating and dressing complete.

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - tratment of soil under existing flooors using chemical emulsion @ one litre per hole, 300mm apart including drilling 12mm diametre holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor - with Chlorpyriphos / lindane E.C. 20% with 1% concentration -

Diluting and injecting chemical emulsion for POST - CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) - Treatment of existing masonry using chemical emulsion @ one litre per hole at 300mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 ( 1 cement : 2 coarse sand) to the full depth of the hole - with chlorpyriphos / lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:5:10 (1 cement:5coarse sand : 10 graded stone aggregate 40mm nominal size)

Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 5 in foundation and plinth in - cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

Steel work in built up tubular (round, square or rectangular hollow tubes etc) trusses including cutting, hoisting fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc. complete. Hot finished welded type tubes.

Steel work welded in built up sections / kg framed work , including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete - 40mm thick with 20mm nominal size stone aggregate

Providing and laying fully vitrified floor tiles of size 600 x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make (Nitco / Rak / Johnson /Asian ) in all colours and shades , laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) , including grouting the joints with white cement and matching pigments etc., complete - size of tile 600 x600 mm

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion, (i) single socketed pipes. 110mm diameter.

Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single push fit coupler : 110mm.

Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single Tee with out door 110X110X110mm.

Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Bend 87.5deg. 110mm bend.

Providing and fixing on wall face unplasticised- PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Shoe (plain)110mm shoe.

Providing and fixing colour coated galvalume sheet of 550 M.P.A yield of AZ 150 strength formed as per patterned steel rib profile with the depth of 31mm pitch of 250mm and overall width of 1060mm and thickness 0.5mm with required J or C hook bolts and nets 8mm dia G.S paint and working etc., complete excluding the cost of purlin , rafter and truss etc.,

12mm cement plaster of mix :Cement mortar 1:6 (1 cement : 6 fine sand)

15 mm cement plaster on rough side of single or half brick wall of mix - cement mortar 1:4 (1 cement : 4 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

Finishing walls with water proofing cement paint of required shade - New work. (Two or more coats applied @ 3.84 kg/10 sqm)

Wall painting with plastic emulsion paint - Royal of approved brand and manufacture to give an even shade - two or more coats on new work

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead - With cement mortar 1:4 (1 cement : 4 fine sand)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty- Float glass panes of thickness 4mm

White washing with lime to give an even shade - Old work (two or more coats).

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade - One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - One or more coats on old work

Providing and fixing G.I.chain link fabric fencing of required width in mesh size 50 x 50 mm including strengthening with 2mm dia wire or nuts , bolts and washers as required complete - Made of G.I.wire of dia 4mm , PVC coated to achieve outer dia not less than 5mm in required colour and shade

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this included jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete (External work) - 20mm nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this included jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete (External work) - 25mm nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this included jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete (External work) - 32mm nominal outer dia pipes.

Providing and fixing brass bib cock of approved quality - 15 mm nominal bore.

Providing and fixing brass bib cock of approved quality - 20 mm nominal bore.

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore

Providing and fixing PTMT bib cock of approved quality and colour - 15mm nominal bore, 86 mm long , weighing not less than 88gms

Dismantling the damaged portion in RCC beams colums and ceiling without affecting the adjacent structure in all floors including the cost of required tools and plants and cleaning the debris from the site with an initial lead of 100 mts away from the buildings etc., complete Rate quoted does not included cost of providing scaffolding

Cleaning and exposed RCC surface thoroughly by washing the copious quantity of water, removing rust and seals from exposed rafters and providing anticorrosive primer Zinc rich coating CERA ZINC ZR. And cleaning the surface for adequate PH using phenolphthalein indicator. complete

Applying of bonding coat by using cement slurry added with polimer additive CERA POLYSTER LATEX over the exposed RCC surface or brick surface as per manufacturers mix and application specification.

Providing cement plastering CM 1:3 over the dismantling RCC portion up to a thickness 15-20mm with cement mortar admixed with CERA MICROSEAL at 500gms per bag of cement. The rate quoted includes cost of sand and admixture but excluding cost of cement and providing scaffolding

MAHADEVAN R