SPL REPAIR TO BLDG NO P-364/01 TO 04 (OR MD ACCN) OF JAT AND SPL REPAIR TO ADM BLOCK BLDG NO P-988 OF FD REGT AT ITARANA MIL STN ALWAR

Taking down cement or cement lime plaster, any description on brick or stone walls,etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engr-in-Charge.

Demolition cement concrete (un-reinforcement) in ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete all rubbish materials complete all as specified and directed.

Demolition of cement concrete (reinforced) in landing slab, chullah hoods ,manhole covers , Roofs, Floors, beams, stair case, landing, chajja and similar suspended work complete all as specified and directed.

Dismantling floor hearth wall tiling (but not backing) removing serviceable tiles to store rubbish off the premises complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars & precast concrete masonry etc complete all as specified & directed.

Demolition of existing lime concrete/PCC padding, Roof treatment of any thickness laid over RCC roof/Chajjas etc removing complete layer of bitumen under concrete/PCC Padding, cleaning and washing of roof with water to remove dust etc as preparation to receive treatment complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n exc 1.5 but each complete all as specified & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 but n exc 4 sqm each complete all as specified & directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc,laid , bedded and pointed in any mortar all as specified & directed.

Cutting holes into stone wall built in cement mortar or cement lime mortar for inserting hold fast and making good dismantle portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc one brick but n exc two brick as required complete all as specified and directed.

M & L for 25mm thick PCC 1:2:4 type B-1 (using 12.5mm graded aggregate) as in leveling coarse of floors and roof complete all as specified and directed.

M & L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base of roof/floor/ pavings/path etc complete all as specified and directed.

M & L for providing cement concrete type B-0 (Using 12.5mm graded stone aggregate) as in padding and leveling course on roof and floor complete all as specified & directed.

M & L Cement concrete type C1 1:3:6 (using 20mm graded stone aggregates) as in plinth protection 75mm thick and surface to be finished even and smooth without using extra cement. Plinth protection shall be laid in panels x.exc 1.5 mtr 6mm wide and 10mm deep joints shall be made between wall & plinth protection and between panel. Joint shall be filled with bitumen mastic and sand in preparation 1:3 (one part of bitumen and three part of sand) complete all as specified and directed

M&L for PCC 1:2:4 type B-1 using 20mm graded aggregate as in cills, coping steps, tank staging, seismic and other similar courses, lacing courses parapet and railing upto 60cm ht kneeler kerb and alike including weathering, slightly rounded or chamfered angle and throating complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (Using 40mm stone aggregate) as in foundation concrete complete all as specified and directed.

M & L PCC 1:5:10 type E2 for sunken filling, foundation, filling and mass concrete complete all as specified and directed.

Providing precast cement concrete 1:2:4 type B-1 as in landing, cover slabs (for manholes etc) Chajjas, water troughs, managers, shelves and Similar article with plain faces complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B0 in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:4 including WPC @ 3% by weight of cement on stone/brick masonry finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. Note : quoted rate is deemed to be inclusive for work at any height and location including cost of scaffolding and all other equipment reqd to execute the work complete all as specified and directed.

Supply only liquid water proofing compound as per IS-2645 complete all as specified and directed.

Taking down carefully existing bitumen tarfelt including plaster of any description over the surfaces of roof, terraces including flashing and junction of parapets/curve walls etc and removing of the rubbish and depositing where directed complete all as specified and directed.

M&L for 15mm thick cement plaster in CM 1:6 on other than fair faces of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even as per manufacturer instructions complete all as specified and directed.

M & L for 15mm thick screed bed on fair faces of concrete/brick surfaces in CM 1:4 with water proofing compound @ 3% of wt of cement finished even and smooth in order to maintain proper slope over existing roof surfaces for laying APP based polymeric membrane finished complete all as specified and directed. (Polymeric membrane and WPC shall be measured and paid separately here in after)

M & L for rendering 5 mm thick cement plaster in CM 1:3 as in ceiling and finish the surface even and smooth without using extra cement complete all as specified and directed

M&L water proofing treatment to RCC roof slab including parapet comprising of following course of treatment/specified from bottom to top complete all as specified and directed. (a) Applying Bituminous primer @ 0.40 Ltr per sqm over plastered surfaces of roof including parapet surfaces. (b) Over the priming coat laying one layer APP based polymeric membrane of approved manufacturer, 3 mm thick weight not less 3.6 Kgs/Sqm and upper side of membrane thermally insulated with white mineral gravel finish, uniformly embedded during manufacturing process shall only be used, it shall be laid by torch application . side overlap should be 75mm and end shall be 100mm. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside parapet in groove. The same shall be finished by a membrane flashing.

M&L for Glazed coloured ceramic tiles in vertical surface 300x450x7 / 300x600x7 mm thick laid over and including 10 mm rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. laid over and including 10 mm rendering or bedding layer in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L non skid ceramic 8-10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M & L non skid ceramic 8-10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm on vertical surfaces such as dado, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick rendering in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for machine cut Green Marble flooring 18-20 mm thick as in floor, cooking platform, treads etc laid over 20mm thick screed bed or bedding layer in CM 1:3 set and jointed in neat cement slurry and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing by machine and including grinding complete all as specified and directed by Engr-in-Charge.

M&L for machine cut Green Marble 18-20 mm thick as in riser of steps, skirting, dado and pillar set over 10 mm rendering in CM 1:3 and jointed with grey cement slurry mixed with pigments to match the shade including rubbing and polishing complete all as specified by Engr-in-Charge.

M&L for 18-20 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over 15 mm screed bed or bedding layer in CM 1:3, including grinding of edges to curved surface finish complete all as specified and directed.

M&L for machine cut 25 to 30 mm thick kota stone in single piece as in shelves and similar works laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including ball nosing of exposed edges and including dismantling old stone slabs complete all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder / rice husk / wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800N (pace) & 900 N (Edge) minimum compressive strength 50n/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, alter/moisture proof and fire retardant, WPC to be laminated with PVC foil of minimum microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed. (Note : stainless steel butt hinges shall be paid separately)

S & F Gauzed shutter made of mild steel framed work as in door frames mad of hollow / square/rectangular /circular section and other covering door to be prepared for handing or sliding with including either hooks, fittings, mortal lock and hanging also fastening and fixing, necessary arrangements for fixing or wiremess necessary bolting incl welding complete, wire gauge will be measured and paid separately complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ugs/SS dash fasteners of required dia including necessary hold fast/lugs or SS dash fastener complete as per direction of Engineer-in-Charge.

S&F Aluminium windows made of 1.59 thick powder coated (thickness of powder coating not less than 50 micron) as per aluminium section of size given below. Aluminium window will be of double shutter of glass/ wire gauge shutters including all necessary accessories jointing cleats , glazing clips, rubber neoprene packing, for fixing glass/ wire gauge, aluminium handles and tower bolt 2 Nos 100 mm ‘D’ Type in each door, 2 Nos 100 mm aluminium hinges including necessary steel screws complete all as specified and directed by Engr The size of different aluminium section to be used is as under (a) Outer Frame 125X45X2.00 mm thick (b)shutter frame section size 44X44X1.59 mm thick for glass and 44x25x1.59mm for wire gauge Note: Rates quoted are inclusive all fittings and fixtures. Glass and wire gauge & MS grill will be paid separately in respective items complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples to wooden/steel frames with beading complete all as specified & directed.

S&F sheet glass, ordinary quality 4.80 mm thick fixed with rubber beading and clips size of glass n.exc 2 sqm in each pane complete all as spd & directed.

S&F in repair vitreous china squatting pan of Orrisa pattern size 580mmx440mm white with integral foot rest (excluding flushing cistern and flush pipe complete including provision of lime concrete bedding complete all as specified & directed.

Supply and fixing in repair PVC flushing cistern low level 10 ltr cap with inlet ball valve float and handle syphonic action type incl brackets and flush pipe of polythene of low or high density ISI marked complete all as specified & directed. Make : Cera / Jaquar / Hindware

S&F in repair 15mm dia bib tap cast copper alloy chromium plated fancy type crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified & directed. Make Jaquar cat Part No CON-047KN or equivalent of Cera / Hindware

S&F in repair 15mm dia stop valve/angle valve of copper alloy fancy type chromium plated screwed down high pressure with crutch or butter fly handle screwed on both ends for iron pipe or for union complete all as specified & directed. Make : Jaquar cat part No CON-053KN or equivalent of CERA/Hindware

S&F in repair swivel shower rose(fancy type) chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified & directed. Make: Jaquar cat part No OHS-1989 or equivalent of Cera / Hindware

S&F in repair Vitreous china corner wash hand basin of size 550mm x 435mm / 400mm x 450mm excluding taps waste chain plug stopper but including brackets waste pipe cutting pinning in ends of brackets complete all as specified and directed. Make : CERA /JAQUAR/HINDWARE.

S&F in repair 32 mm dia PVC flexible waste pipe for WHB/Sink 600 mm long with PVC coupling all as directed fixed in repair complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 20mm bore pipe complete all as specified and directed.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 20mm dia complete all as specified and directed.

S&F tubes medium grade 'galvanised' with and including all fitting and fixed bore of 20 mm dia complete to walls and ceiling or laid in floors of 20 mm bore complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store 15mm bore pipe complete all as specified and directed.

Refixing old steel tubing and connection in new or old position (walls, ceiling, floor etc) bore of pipe in 15mm dia complete all as specified and directed.

S&F tubes medium grade 'galvanised' with and including all fitting and fixed bore of 15mm dia complete to walls and ceiling or laid in floors of 15mm bore complete all as specified and directed.

S&F in repairs sink with drainage board made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 915mm x 460 mm with bowl size 410mm x 330mm x160 mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, including taking down old unserviceable sink complete all as specified and directed.

S & F in repair stop valves 20mm bore, cast copper alloy screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Dismantling of water tanks of capacity exc 250 but n exc 500 ltrs & removing to stores complete all as specified & directed.

S&F 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified & directed.

S& Fixing in repair ball valve brass high pressure with polythene float and fly nut screwed on iron pipe ad fixed 20 mm bore of pipe complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair Floor Drainer with Collar and Cockroach Trap/Jali with or without waste hole complete all as specified and directed.

S&F in repair brass chromium plated soap dish, complete all as specified and directed.

S&F in repair brass chromium plated towel ring incl a pair of CP brass bracket complete all as specified and directed by Engr-in-Charge.

S&F in repairs 15 mm bore fancy type long body bib tap, half turn, with wall flange, cast copper alloy with capstan heads, chromium plated, screwed for iron pipe or for brass ferrule, complete all as specified & as directed. Make JAQUAR Cat Part No CON-107KN or equivalent of CERA / HINDWARE

S&F in repair 15mm dia bore cast copper alloy chromium plated fancy type pillar tap with out cold & hot water complete all specified and as directed. Make : JAQUAR Cat part No CON-021KN or equivalent

S&F in repair CP brass mixer for Wall mixer hot & cold water for screwed down for iron pipe and fixed bore of pipe in 15 mm complete all as specified and directed. Make :JAQUAR cat part No CON-219KN or equivalent

S&F in repair PVC (SWR) pipes of 75 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed.

S&F in repair PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.8 mm) single socketed in any length with rubber ring joints laid in trenches or in floors of 75mm pipe i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed.

S&F in repair PVC (SWR) pipes of 75 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed.

S&F in repair PVC (SWR) pipes of 110 mm bore single socketed in any length fixed to wall i/c taking out old u/s PVC/CI pipe with fittings complete all as specified and directed.

S&F in repair PVC (SWR) floor trap, plain with grating including joining with solvent cement 75 mm dia complete all as specified and directed.

S&F in repair PVC (SWR) bend 75mm bore of any radius complete all as specified and directed.

S&F in repair PVC (SWR) bend 75mm bore of any radius with access door complete all as specified and directed.

S&F in repair PVC (SWR) bend 110 mm bore of any radius complete all as specified and directed.

S&F in repair PVC (SWR) bend 110 mm bore of any radius with access door complete all as specified and directed.

S&F in repair PVC (SWR) branch piece single PVC (SWR) (Single T) equal or unequal of 110 mm bore with access door complete all as specified and directed.

S&F in repair PVC (SWR) branch piece single PVC (SWR) (Double T) equal or unequal of 110 mm bore with access door complete all as specified & directed.

S&F in repair PVC (SWR) branch piece single PVC (SWR) (Single T) equal or unequal of 75 mm bore with access door complete all as specified & directed.

S&F in repair PVC (SWR) vent cowl 110 mm complete all as specified & directed.

Demolition and breaking up drain pipes (Salt glazed stone ware, AC, or Reinforced concrete) or 100mm dia set in cement mortar including PCC bed to drain pipe, packing under & hunching against the sides of drain pipes complete all as specified & directed by Engineer-in-charge.

S&F for 75mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard, minimum load bearing capacity 5 ton/sqm, in square, rectangular or circular shape complete all as specified & as directed.

M&L 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars including demolition and breaking up old existing pipe complete all as specified & as directed.

M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone agg) as bed to drain pipe including in packing under and hunching against sides of pipes after they are laid and tested in complete all as specified for 100mm dia pipes complete all as specified & as directed.

M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 100mm bore pipe complete all as specified & as directed.

S&F mild steel butt hinges medium weight colod rolled of size 100mm, ISI marked complete all as specified and directed.

S&F Stainless Steel hinge pin butt hinges 100mm long complete all as specified & as directed.

S&F in repair stainless steel, sliding door bolt with hasp, staple (bolt type) 300mm long not less than 12mm dia with and incl minimum of 06 bolts and nuts, 4 on plate and 2 on staple and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, plate and fixed complete all as specified & as directed.

S&F stainless stee, barrel tower bolts of extruded section and fixed 150 mm long complete all as specified & as directed.

S&F stainless stee alloy handles 125mm size fabricated type anodized ISI marked complete all as specified & as directed.

S&F stainless steel barrel tower bolt 200mm long stove enameled black with bright bolt & fixed complete all as specified & as directed.

S&F stainless steel bow handle of 150mm size oval type stove enameled black complete all as specified and directed.

S&F in MS Retractable Hinge fixed to wooden or steel frames with Screws/welding as required at site complete all as specified and directed.

S&F 140 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, with vulcanised rubber piece fixed in floor complete all as specified and directed.

S& F in repair stainless steel plate rack out of 1.00 mm thick sheet of size 900 x 750 mm and depth of shelves 230 mm with partition for small /large plates made out of stainless steel 24 gauge all as per sample to be hanged on wall by the help of steel screws grouted in walls with rawl plug design as approved by GE/Kept in GE Office.

M&L for pressed steel shutter 1mm thick including pressed steel frame of 1.25 mm thick sheet, 12mm dia M S rod for locking, two Nos chromium plated handle and one mortise pattern lock incl two coats of spray painting over a coat of shop primer complete all as shown on drg no TD/2004/29 sheet no 1/3 to 3/3

S&F (in repair) curtain rod with fixing bracket, stops, rollers etc complete all as specified and directed.

S&F in repairs Stainless Steel drapery rod of 25 mm inner dia (in length as directed ) of approved colour with & including matching finials at both ends and pair of SS brackets fixed at both ends with PVC rawl plug & steel screws on walls/beams including PVC curtain rings of matching colour @10 cm c/c all as specified and directed

M&L for 50mm thick sand stone slab in sunshades, chajjas, shelves, cills, landings, cover stones, templates etc not exc 2m in length, punched dressed on face and along exposed edges, self faced on the other Side and set and pointed in cement mortar 1:4 complete all as specified and directed.

M&L for TMT bars 10mm dia and over cut to length to shape required including cranking, bending spirally or hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

All as per srl item No 102.00 but for 6mm to 8mm dia TMT bars.

Excavating in trenches n exc 1.50m in width and n exc 1.50m in depth for foundation, manholes etc as well as n exc 10 sqmm on plan area and getting out in soft/loose soil all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25 cm thick in soft/loose soil complete all as specified and directed.

Removing excavated soil to a distance exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in 1:4 as in half brick thick wall complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 mean radius, built in CM 1:6 complete all as specified and directed.

S&F frame work such as grills, gratring etc, with ends of bars shouldered &/or riveted or forged into spikes, framed guard bars, barred iron door ladder, frame balusters, walk ways, railing, frame work or water tanks & Similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L flat iron as in hold fast welded to angel iron door/window frames complete all as specified and directed.

S & F for framed work as in doors or gates or tank cage, angle or other covering door ect to be prepared for handing or sliding with including either hooks and hinges or steel hanging door fittings and including all necessary nuts and bolts and welding reqd and hanging also fastening and fixing complete conforming to FE-290 Gde E-165 complete all as specified and directed.

M & L for welded mild steel wire mesh of mesh size 30mm x 30mm and wire size 1.4mm incll all necessary nuts and bolts / welding clamps reqd for fixing into angle iron frame complete all as specified and directed.

M&L for Vibrator moulded (Coloured) precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over 25mm thick sand cushion and filled the joints with dry sand after laying the paver block complete all as specified and directed.

Treatment of sunken portion is as follows :- M & L for water proofing treatment in sunken floors as described hereunder:- (i) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick cement plaster in mortar 1:4 mixed with water proofing compound @ 3% by weight of cement. (ii) Preparing plastered surfaces and providing APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and as directed. Note: (i) Polymeric membrane shall be laid in sunken floor and on sides upto finished floor level (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iii) Above aspects are deemed to be included in quoted rate. (iv) Horizontal floor area shall be measured for payment purpose.

S&F for preparation of new steel surface/old untreated of any description over 10cm width or girth & applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

M&L for preparing newly plastered surfaces & applying two coats of oil emulsion distempering (OBD) over and including a coat of white wall care putty 2 mm thick over a coat of primer on walls complete all as specified and directed.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, molds, moss, efflorescent salt, trading oil grees spots etc using grinding machine on wall surfaces and preparation of old plastered wall surfaces and applying two coats of oil emulsion distemper ( OBD) of approved shed/tint over and including a coat of white wall care putty 2 mm thick over a coat of primer complete all as specified and directed.

M&L for preparing newly plastered surfaces & applying three coat of white wash on ceiling complete all as specified and directed.

M&L for preparation of old surfaces and applying two coats of white wash on ceiling complete all as specified and directed.

M&L preparing newly plastered surfaces of walls and applying two coats of exterior emulsion paint over a coat of 2mm thick exterior wall care putty on walls complete all as specified & as directed. Note:- Wall care putty shall be paid for separately under respective item.

M&L for preparing newly pastered surfaces of walls, plastered and applying 2mm thick exterior wall care putty on walls to prepare the surface even and smooth complete all as specified & as directed.

M & L for writing letters or figures (Block, Roman, Italic or Indian) n. exc 30 cm height with thick synthetic enamel paint. complete all as specified and as directed by Engr- in - Charge.

M&L for form work to soffits of suspended slabs such as roof slabs etc for rough finished concrete surface complete all as specified and directed.

M&L for form work to SIdes for slabs and Sides of RCC/PCC bands in walls, horizontal or sloping and Similar work exc 10 cm but n exc 20 cm wide for fair finished concrete surface complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (Nominal mix) using 20mm graded crushed stone aggregate as in roof, floor, slabs supported on walls complete all as specified & as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified & as directed.

Cutting Chases exe 10 cm but n exc 20cm in girth in brick/stone wall for fixing of PVC Pipe/GI pipe of 15 & 20 mm bore (concealed in wall) including making good surface in CM (1:6) & to match with the existing surfaces complete all as specified & as directed.

M&L for cutting holes in stone /RCC/granite slab for inserting cooking gas cylinder pipe and making good complete all as specified & as directed.

S&F factory made kitchen cabinet of size 1.5M x 0.60M x 0.3M, made out of 18mm thick PVC celuka sheet having density not less than 650kg/cum one side decorative lamination & other side balancing lamination sheet consisting of carcase 18 mm thick PVC sheet including shutters made out of 18 mm thick PVC board all required brackets 5.5 screws etc. The panels shall be fabricated using adhesive and screws where every required. All edge shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per drawing and specification approved by Engineer-in-Charge Note : (i) PVC celuka sheet manufactured by an ISO 9001-2015 certified company, termite proof, water proof & flame retardant PVC sheet. (ii) PVC cabinet of required size fabricated by joining four 18mm thick PVC celuka ply fixed with each other using solvent cement adhesive and screws and 18mm thick PVC sheet as backing of cabinet screw and solvent cement adhesive etc. (iii) The Cabinet box will be divided into two equal part with two leaf shutter and one shelf will be placed in cabinate (iii) Cabinate will be fixed in wall with 4x fasteners etc and necessary fixing lugs (iv) Each shutter will be provided with SS handle 75 mm, CP Piano hinges, magnet/catcher (v)The quoted rates are included the rates of all fittings and fixtures

Supplying and fixing PVC Shutter for kitchen cabinets and trolley shutter made of 18mm thick PVC Celluka ply having density 600kg cbm density with pre-laminated sheet on one side and other side balancing white incl shutter. The PVC sheet shall be cut in desired shape and size put together and jointed with necessary adhesive and screws where required. all edges shall be covers with edge bonding tape of same colour. The shutters will be below kitchen counter with necessry fittings and fixtures complete all as specified and directed by engr in charge. Shutter will be provided with SS piano handle 75mm, continuous CP piano hinges and magnetic catcher. Note : The Coated rated are included all fittings and fixtures

S&F for Pipe Supporting Clamping - for GI pipe 2 Nos for 15mm and 2 Nos for 20mm down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE. complete all as specified and directed

S&F for Pipe Supporting Clamping - Single Pipe of dia 3" (75 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 3" (75 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE. complete all as specified and directed

S & F for Pipe Supporting Clamping - Single Pipe of dia 4" (110 mm) down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt R/M System running vertically with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of Size 10" - 1 No.; 3. U Bolt R/M for 4" (110 mm) CI or PVC Pipe Dia. - 1 No.; and 4. Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing No. : CE Jaipur Zone - Jaipur; TD/2022/102. Make: Shaivi or equivalent as approved by GE.

Supply only liquid water proofing compound as per IS-2645 complete all as specified and directed.

M&L taking down and removal of loose / disintegrated old concrete up to 50mm depth/ plaster and cleaning all loose dust washing with water and epoxy bonds materials of pidilite/Dr fixit with new cement plaster /polymer modified plaster/concrete /screed concrete with old surface etc complete all as specified and directed.

M&L applying 15mm thick plaster with polymer modified mortar in proportion 1:3 by weight 5 litres SBR 45 to added to 50kg cement with 13 litre water addition finished surface to match with existing adjoining surface of ceiling, beams and alike complete all as specified and directed. Make : Nitobond/Fosroc/Dr fixit

M&L and applying two or more coats of 2 component zinc based epoxy rust preventer on corroded reinforcement after cleaning and removing the rust from corroded reinforcement with the help of wire brush and treating it with rust remover (Reebaklens RR) including thoroughly cleaning washing air blowing brushing etc complete. Dia of bar upto 20mm Note : Qty of zinc based epoxy rust prevent or only shall be taken into account for payment purpose on the basis of actual consumption complete all as specified and directed.

All as srl item No 137.00 but for as in skirting/dado including cement mortar rendering/ screeding 1:4, 10mm thick complete all as specified and directed.

M&L for machine cut Green Marble 18-20mm thick as in riser of steps, skirting, dado and pillar set over 10 mm rendering in CM 1:3 and jointed with grey cement slurry mixed with pigments to match the shade including rubbing and polishing complete all as specified by Engr-in-Charge.

M&L 12mm thick vitrified exterior grade textured finished tiles (FOR PARKING/PORCH) of size (30cmx30cm/40cmx40cm) set and jointed in net cement slurry in floor including cement mortar screed bed 1:4, 20mm thick and pointing with admixture of white/colour cement and pigment complete all as specified and directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L 25mm to 40mm thick unpolished cuduppah stone slab as in vertical support for cooking platform and like incl necessary jointing and pointing and making good to disturbed surface complete all as specified and directed.

S&F fixed in repair vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc. & with Self closing plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

S&F in repairs vitreous china wash basin white of size 550x400 mm with padestal stand including 32 mm CP waste coupling & PVC flexible waste pipe of min 60 cm long, flat back or angle back type excluding taps, waste chain & plug but including cast iron brackets and cutting for and pinning in ends of brackets or erecting stand complete fixed in repairs complete all as specified and directed. Make : JAQUAR/CERA/HINDWARE

S&F in repair 15mm dia bore cast copper alloy chromium plated fancy type pillar tap(Swan Neck) for with out cold & hot water complete all specified and as directed.

S&F repair vitreous china wash basin oval type (Counter top) white of size 550mmx400mm fixed in granite etc including 32mm dia CP brass waste coupling fitting and union complete all as specified and as directed.

S&F in repair Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm-45gms/40mm-60 gms) fixed in repair complete all as specified and directed.

S&F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S& F 1000 Ltr capacity of rotational moulded polyethylene water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including S&F 20mm float valve 20mm dia GI pipe medium grade washout pipe 450mm long with plug and 20mm dia GI pipe medium grade overflow pipe 600 mm long with fitting and including dismantling of tank complete all as specified and as directed by the Engineer-In- Charge.

S&F in repair sheet glass self assembly consisting of 5.5mm thick sheet glass shelf 12cm wide chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair brass chromium plated fancy type toilet paper holder complete all as specified and directed

M&L for preparation of old surfaces of ceiling and applying two coats of oil bound distemper on ceiling complete all as specified and directed.

Material and labour for preparation of newly plaster surface of wall & applying two coat water based premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over priming coat with fully automatic airless spray machine of paint application with a flow speed of min 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in both the coats of paint. Make - Nerolac Excel Top guard (10 years product warranty)/ Asian Paints Ultima Protect (10 years product warranty)/ Berger weather coat long life 10 (10 years product warranty) at any height including necessary scaffolding.

Dismantling wall and any type of ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness fixed to any type of frame including cover fillets complete all as specified and directed.

M&L wall paneling made of 5 mm thick prelaminated PVC hollow section with tonge and groove joints fixed on wall with necessary screw and adhesive complete all as specified and directed by engr in charge. PVC U channel will be provide on top and bottom and PVC angle will be provided in all corners of complete al as specified and directed consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawings.

S & F in repair Vitreous China urinals, half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe (excluding flushing cistern, flush pipe and waste pipe) Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) including all fitting complete all as specified and directed.

Supply and fixed in repair vitreous China Urinal With Fixing Accessories, including urinal spreader Size: 355x340x535 mm Jaquar cat No URS-WHT-13261 or equivalent complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/Aluminium point wiring for light/fan/socket/light fitting/power point and taking down of teak wood batten / PVC casing caping/PVC conduit/steel conduit and making good disturbed surfaces of walls/ceilings /floors etc incl dismentling of fittings.

M&L for concealed Point wiring with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with modular sheet top cover of required module with frame for mounting switches, sockets etc complete all as specified. Note -(a) Quoted rates shall be deemed to include the cost of Cutting Chases in Stone/Brick wall and making good to the disturbed surfaces including plastering and painting to match with the existing colour. (b) The rates Quoted by the contractor shall be deemed to include the cost of modular cover plates of required module with frame, cost of Sheet Metal Box and no additional payment shall be made on account of the same.

All as per srl item No 159.00 but for one fan point controlled by one switch and regulator

All as per srl item No 159.00 but for one exhaust fan point/Fresh Air Fan Point controlled by one switch .

All as per srl item No 159.00 but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per srl item No 159.00 but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per srl item No 159.00 but for one bell/buzzer point controlled by one bell push

All as per srl item No 159.00 but for one light point controlled two ,two way switches

All as per srl item No 159.00 but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

All as per srl item No 159.00 but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade including 4.0 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLSH cable 1100 Volt grade as continuous earth wire in green colour.

Supply and fixing switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts.

S&F switch piano flush type single pole two way 5 Amps 230 Volts .

S&F bell push flush type 5 Amps 240 V complete all as specified & directed.

S&F bell/buzzer AC 230 volts single pole complete all as specified & directed.

Supply and fixing switch piano, flush type, single pole, one way, 15 Amp, 230 Volts.

Supply and fixing socket outlet, 3 pin (with 2 pin outlet also), 5/6 Amp, flush type, 240 Volts.

Supply and fixing socket outlet, 2 in 1, 3 pin, 5 and 15 Amp, flush type, 240 Volts.

Supply and fixing ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified.

Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part Stella 20 Watt Galmtube LHEWAJPGPV1D020

Supply and fixing lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified.

Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours. Make : - Havells/Philips/Bajaj

S&F LED type building security light of aluminium housing light luminaire 25 watt 230 V 50 Hz including all as necessary fitting accessories and LED complete all as directed. Make : Philips/Havells/Crompton

Supply and fixing sheet metal enclosures double door type suitable for fixing MCB's, SPN with 200 Amps rated bus bar,8 way, 240 Volts.

S & F MCB 32/40 Amp, single pole & neutral,240 Volt complete all as pecified & directed.

S & F MCB 6-40 Amp, single pole 240 Volt complete all as pecified & directed.

S&F sub main wiring on and including passing through PVC conduit in concealed (including cutting chasis in stone/brick wall) 1100 Volts grade with PVC flexible cable copper conductor cable fire resistant low smoke and halogen (FRLSH) unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. (Note: Two runs of cable with one run of earth wire and one run of PVC Coundit should measured as one length)

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & directed. Note : - Quoted rate shall be deemed to include for earth wire with protection pipe up to 7.5 meter length.

M/L for GI pipe (Light grade) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore

Supply and fixing in repair of 25 mm bore GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe complete all as specified and directed.

M & L for Gun-metal, globe or gate valves, 25 mm bore of pipe with iron wheel head, screwed both ends with GI Union for iron pipe and fixed complete all as specified and directed.

Supplying, laying, jointing, testing and commisioning of size 4 core 25 Sqmm LT under ground cable, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall complete all as specified and directed. Note :- Exacavation and earth work, GI pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid seprately under respective items of the BOQ'.

Supplying, laying, jointing, testing and commisioning of size 2 core 10 Sqmm LT under ground cable, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with multistranded aluminum conductors, 1100 Volt grade, laid in trenches / ducts / encased in GI pipe / fixed to pole/wall complete all as specified and directed. Note :- Exacavation and earth work, GI pipe for laying of cable, sand cushioning, cable protection cover shall be measured and paid seprately under respective items of the BOQ'.

Boring of holes under road, payment hard standing by trench less technology using ultra sound technique and necessary machine including supply and fixing HPDE pipe of 80 mm bore suitable for 0.4 mpa working pressure all as specified and directed.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

Disconnecting form elect connection and taking down carefully the existing Ceiling fan/Exhaust fan/Geyser of any capacity, any make,any size and depositing same the Ceiling fan/Exhaust fan/Geyser in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same Ceiling fan/Exhaust fan/Geyser carefully incl necessary electric connections complete all as directed.