PROVN AND INSTLN OF RECYCLING INCINERATOR MACHINES I.E. PLASTIC WASTE SHREDDER WITH COVERED DUSTBINS AND STANDS UNDER GE SAUGOR

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or smiliar holes) each n exc 0.50cum getting out in hard/dense soil, returing & filling and ramming earth in broken rubble mixed with earth around in layers not execeeding 25 cm complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator) means over areas in soft/loose exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan complete all as specified and directed.

Removing excavated material (soil) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Approved earth filling with approved soil brought from out side MD land, filling in trenches or paving laid in layers not exceeding 25 cm thick spread, levelled and rammed including watering etc complete all as specified and directed.

M&L for hardcore with broken stone or boulders of gauge n exc,. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M & L for cement concrete type D2 1:4:8 (40 mm graded aggregate in foundations, filling and mass concrete complete all as specified and directed.

S&F steel work in Tubular Roof trusses, purlins, rafters including special shaped washer etc complete using ERW or induction butt welded tubes confirming to I.S 1161 1979 grade st 240 complete all as specified and directed.

S & F plates (pain or chequred channels, square cut or notched (ordinary and counter sunk) forming without any attachment cofirming to Fe-410W (Grade E-250) quality A complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating (AZ-150) corrugated steel sheet 0.50 mm of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall. Fixed with self tapping screws complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating (AZ-150) plain steel sheet 0.50 mm of any colour having tensile strength of 550Mpa as in roof covering /cladding to wall , fixed with self topping screw complete all as specified and directed.

M&L for preparation or new steel surfaces and apply 2 coats of synthetic enamelled paint over a coat of red oxide primer over 10cm width or girth complete all as specified and directed.

M &L for Brickwork with subclass 'B' bricks, straright or curved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed.

M&L for rendering in two layer , first layer of 15 mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:4) and second layer of 5mm thick in CM 1:4 with and including water proofing compound @ 3% by weight of cement complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8 type D 2 using 40mm graded stone aggregate as in sub base of flooing complete all as specified and directed.

S&F for Mild steel TMT bars 10mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed.

M & L for reinforcement cement concrete type B-1 ,1:2:4 using 20 mm graded agregate for foundation, including rafts, footings, foundation beams plinth beams, bases for coloumns etc basement slab under reamed and mass concrete complete all as specified and directed.

S & F framed work such as grills, gratting,framed brackets of angles or tees with web and flange cut to shape etc with ends of bars, shouldered and/or reveted, or forged into spikes, framed guard bars, framed works of water tankes stagging,gates and similar work con-forming to Fe.290.Gde-E-165.

S&F Mild steel screw bolts (machine made) with hexagonal / square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long dia of shank 16 to 20 mm complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail?ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon?tal or sloping and similar work exc 10cm but n exc 20cm wide for smooth and fair sinish complete all as specified and directed.

S&F Rotational mounded polythene water storage tank of 1000 ltrs capacity, (multilayered, cylindrical, vertical with closed top) hoisted and fixed in position as specified in SSR Pt-I complete all as specified and directed.

S&F ball brass valves high pressure with polythene float and fly nut complete screwed for iron pipes of 20 mm dia or brass ferrule and fixed, complete all as specified and directed.

S&F Gun metal globe or gate valve with Iron wheel head, screwed both ends for 15 mm dia of pipe and fixed complete all as specified and directed.

S&F 15 mm bore galvanised steel tubes medium grade with all fittings for water supply pipes fixed to walls complete all as specified and directed.

S&F 15 mm dia bib taps, fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

Supply, installation testing and commissioning ECHOGENIC WASTE DISPOSAL SYSTEM suitable to operate at 415 V AC power supply with power load 12 KW for mixed solid waste(MSW) dry and wet paper waste, cartons waste, plastic waste polythelene bag, organic waste, plastic sheets and plastic scrap , organic waste with less than 40% moisture with disposal capacity 100-150 Kg/day and volumetrically 0.5 m3 with necessary heater arrangements and multi layred venturi water wet scrubber for flue gas treatment and 6 meter height MS constructed chimney, single feeding point, temperature 350 ⁰C to 400 ⁰C with pressure release valve and temperature monitor sensors, rox wool heat proof insulation 3 Nos of Dustbins 16-20 Ltrs Capacity pole Mounted including transportation and operational training to operating staff complete all as specified and directed.

Supply, installation testing and commissioning Twin Shaft Shredder Machine Length of Shredder :400mm. width of shredder :400 mm Height of shredder :1000mm Motor :5HP (2 Motors) with gear box . Blade material :AR500-18 Nos capacity:200-250Kg/Hr including transportation and operational training to operating staff and including necessary foundation work for platform complete all as specified and directed.

Supply and fix gun metal gate valve with iron wheel head screwed both ends of dia 20 mm complete all as specified and directed.

Supply and fix ball valve high pressure PTMT with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed for dia of bore 15/20mm complete all as specified and directed.

Supply and laying UPVC pipe of 20 mm bore of pressure rating 10 Kg/cm2 fixed including all fittings and fixture complete on ceilng/wall/floor complete all as specified and directed.

M&L for cutting existing GI/CI tubing suitable for pipe 25/40 mm bore for alternation or addition complete all as specified and directed.

Supply and laying cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 70 sqmm 3.5 core complete all as specified and directed.

Supply & laying GI pipe light grade with all fittings complete fixed to walls/poles/ laid in trenches for cable protection 40mm dia complete all as specified and directed.

Excavation in trenches n.exc 1.5mtr wide and n.exc 1.5mtr in depth and getting out in hard/ dense soil for cable/pipe/poles, trimming the sides forming bottom surface to required levels complete all as specified and directed.

Returning filling in & including spreading leveling watering and well ramming 20 cm thick using riddled earth as protection to cable and balanced depth using excavated earth in layers not exc 25 cm complete all as specified and directed.

Supply and laying un-reinforced precast concrete cable cover class LV, type-2, flat size 250mmx150mmx40mm complete all as specified and directed.

S&F cable route indicator made of 15 x 15 x 6mm thick MS plate welded with 10mm x 30cm long MS rod grouted in PCC block of size 0.2 x 0.2 x 0.3 m and writing LT cable complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 600×600×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion including GI pipe light grade 40 mm bore for protection of earth lead,GI funnel and wire mesh etc complete all as shown in Electrical plate no 5 of SSR 2009 (part- I) including necessary excavation earth work, form work.earth pit of size 450X450X300 mm of PCC M-15 (Nominal mix)using stone aggregate earth pit cover of C.I and 20 mm bore light grade GI pipe for watering and charcoal dust,common salt, and connected to test point 7.5 mtr from earth pit including testing complete all as specified and directed.

S&F vertical distribution board double door 4 way suitable for mounting MCCB 125 Amp, 16 KA as incomer and MCB FP 63 Amps 2 Nos (one spare) as outgoing including MCCB and MCBs all as specified and directed including mounting arrangement as per site requirement.

Electromech Engineers (BID ID -3380882)