Addn/Altn in toilet complex of Bldg No.P-314 of 3 PARA (SF) and Execution of certain revenue works at Jaipur Mil Stn under GE(S) Jaipur

Amount

36/LBW/19-20 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

S&F Coloured Glazed ceramic tiles of size 300x450mm x 7mm thick edge cut/ joint free , on walls etc. set & jointed in neat cement slurry & pointed in white/coloured cement to match over 15mm thick plaster in CM(1:4)

S&F Coloured Non Skid ceramic tiles 6 to 7mm thick edge cut/ joint free (squares/ rectangular) area of each tile exc. 0.11 sqm but not exc. 0.18 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match over 15mm thick screed in CM(1:4). 36/LBW/19-20 - 150 89/Rev/19-20 - 6

Demolition of PCC in ground floors and pavings not exc 15cm thickness (below or above ground level )

M/L PCC 1:2:4 type B0 as in under mass concrete under WCs with using water proofing compound. (Water proofing compound will be measured separately.)

M & L painting the roof surface with one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384 and layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.5 Kg/m2 reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions.and finally applying one coat of Bitumen coat @ 1.2 Kg/Sqm over APP Membrane. for toilets sunken floors completed all as specified and directed.

Supply only WPC ( water proofing compound)

S&F in repairs soap dish vitreous china white approximate size 160 x 160 x 90mm or equivalent

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity including Dismantling water tanks & removing to store

S&F Ball brass valves 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule and fixed in repair

Dismantling and taking up or down the existing unserviceable GI pipe and M&L for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of following sizes :-

15 mm bore

20 mm bore

25 mm bore

Taking down cement plaster including raking out joints, hacking for key scrubbing down with water etc built in cement mortar.

M&L rendering 15 mm thick in CM(1:6) on brick walls or concrete surface, surface finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surface other than fair face of brick work of walls, finished fair & even. 36/LBW/-19-20 - 100 89/Rev/19-20 - 40 79/Rev 19-20 - 10

M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper of approved shade/tint over a coat of Birla wall care putty on walls all as specified & directed by Engineer-in-Charge 36/LBW/-19-20 - 100 89/Rev/19-20 - 05

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint of approved shade on walls all as specified & directed by Engineer-in-Charge. 36/LBW/-19-20 - 100 89/Rev/19-20 - 40

Taking down Chowkats or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames)

Taking down Chowkats or frames not exc 1.5 sq. m each with shutters (without taking off shutters from the frames)

Taking down shutters of any description exc 1 sqm and but n.exc 2 sqm each.

Providing and fixing 28mm thick "Rajshri " Brand factory made PVC Supreme Door Shutter consisting of frame made out of m.S. tubes of 19 gauge thickness nd size of 40mmx20mm for stiles, top and bottom rails having a coat of steel primers of approved make and manufacture. M.S. Frame covered with 4mm thick heat moulded "Rajshri" Prelam PVC 'C' Channel of size 28mm thickness,75mm width out of which 60mm shall be flat and 15mm shall be tapered in 45dgree angle on either sides forming stiles, top and bottom rail and 100mm wide Rajshri Prelam PVC sheet out of which 100mm shall be be flat and 15mm shall be tapered An additional of 5mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete on both sides to form lock rail.Lock rail shall be provided on either side of panel. Panelling of 4mm thick PVC sheet to be fitted in the MS Frame welded/sealed to the stiles with 8mm (4mm + 4mm) x 12mm wide PVC sheet as beading on inner side and 8mm (4mm + 4mm) x 20mm wide PVC sheet as beading on the inner tapered side of lock rails joined together with solvent cement adhesive. An additional of 4mm thick PVC sheet of 20mm width is to be stuck on the interior side of 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification and drawing.

Providing and Fixing Factory made Rajshri Adjustable (PVC) Door frame Manufactured by M/s Rajshri of the size 65mm x 60mm with a wall thicknes of 4mm, made out of extruded 4mm PVC foam sheet, metre cut at two corners and joined with 2nos. of 150mm long brackets of 15 x 15mm M.S. Square tube. The two vertical door profile are to be reinforced with 40 x 20mm M.S. tube of 19 guage through out the frame. The doorframe shall be fixed to the wall using 65/100mm long M.S. Screw through the frame by using PVC fastners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2 nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge.

35mm thick IInd class hard wood factory made plain, framed, panelled shutter (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & steel as per IS:1003 (Part-I) kiln seasoned & chemically pressure treated.

Cutting holes in stone / brick walls built in CM for inserting hold fast & making good dismantled portion in CM (1:3) depth of embaded portion of holdfast n. exc half brick

MS butt hinges medium weight, cold rolled size of hinge 100 mm long. 36/LBW/-19-20 - 33 89/Rev/19-20 - 3

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section. 36/LBW/-19-20 - 22 89/Rev/19-20 - 2

S&F Aluminium alloy, anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) & fixing clips of sheet, . or extruded sections & fixing bolts & sliding bolts of extruded sections or . aluminium alloy.

S&F Aluminium handles 125 mm size, type, anodised 36/LBW/-19-20 - 22 89/Rev/19-20 - 2

S&F aluminium anodised floor door stopper overall length 140 mm double legged with rubber shoe, fixed to bottom rail of door as directed.

S&F MS spring hinges 300 mm, ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden/ angle iron chowkats .

Dismantling of old U/S gratingand M&L of PVC Nahani / floor trap and square in size of 100X100 mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap / Nahani trap.( Make Paryag and equilant )

Preparation of new wooden surface of any description, not otherwise, described, over 10cm width or girth and applying two coats of synthic enamel paint over a coat of pink primer complete.

Factory made steel ventilators with top hung shutters incl hinge steel peg stay complete incl. taking down old ventilator

Hacking out old broken glass pane (any thickness, size, quality/ description) from metal/wood frame including punching or drilling out old glass panes, pins, springs, clips & providing & fixing new ones 3 mm thick plain sheet glass ordinary quality in square not exceeding 0.50 Sqm in each pane. glazed with oil putty.

S&F Sheet glass 4.0mm thick, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane

S&F Galvanised mild steel wire cloth, 0.56 nominal dia of wire & average width of aperture 1.18mm with tinned tacks, or galvanised wire staples as in repairs.

Preparation of new steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide /zinc chrome primer complete. 36/LBW/19-20 - 10 80/Rev/19-20 - 20

M&L 50 mm thick PCC type C-1 (1:3:6) using 20 mm graded stone aggregate finished even and smooth without using extra cement as in plinth protection

S/F in repairs Bib taps, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed, fancy type chromium plated long body 15 mm complete.

S&F in repairs Cast Iron sand cast soil, waste and vent pipe 75mm bore in any length with or without ears with cement joints fixed to walls

S&F in repair Cast Iron sand cast soil, waste and vent pipe 100mm bore in any length with or without eaars with cement joints fixed to walls

S&F in repair Cast Iron bends any radius 75mm dia

S&F in repairs Cast Iron bends any radius 100 mm dia

S&F in repairs Cast Iron branch pieces single, (Single T) equal or unequal 75mm dia

S&F in repairs Cast Iron branch pieces single, (Single T) equal or unequal 100mm dia

S&F in repairs Cast Iron cowl 100mm dia

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement fixed in repairs.

S/F in repairs stop valves, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends fancy type chromium plated with long shank and cup (concealed type), 15 mm 36/LBW/19-20 - 9 89/Rev/ 19-20 - 1

M&L Chromium plated Overhead Rain shower with relvoling joint and 115mmlong shower arm with wall flange 15 mm bore fancy type any colour (Make-CERA CAT PART NO CP 140 or equivalent of MARC, JAQUAR) and fixed in repair

M&L Chromium plated angle stop cock with wall flange fancy type cast copper alloy 15 mm bore any colour (Make-CERA CAT PART NO CQ 608 or equivalent of MARC, JAQUAR) fixed in repair

M&L CP cast copper alloy bib taps Long body with wall flange fancy type of 15 mm bore quarter turn (Make-CERA CAT PART NO CQ 604 or equivalent of MARC, JAQUAR) fixed in repair.

S&F in repairs Vitreous China wash hand basin Ovel type basin including half pedastal CERA Part No 1071 CYRCSS white / , coloured, , size 610x560mm including CP waste coupling, waste pipe, chain & plug piller tap, ( Make-Make-CERA CAT PART NO1071 or equivalent of , HINDWARE/ PARRY WARE ), fixed in repair

S/F of Vitreous china Urinal Half stall complete including providing and fixing plugs , bedding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws pointing around urinal fixingCP brass flush cock flush pipe grating and union for discharge pipe

M&L for providing circular, raised platform of height 20 cm below the tank and base 15cm more than the external dia of thank of PVC cylindrical water tank of capacity 500/1000 liters using PCC 1:3:6 type c1 using 20mm graded stone aggregate with smooth finish

S&F PVC connection 15mm bore with 2 Nos PTMT nuts, 45cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe all as directed by Engineer-in-charge. Make - PRAYAG/SIMET 36/LBW/19-20 - 10 89/Rev/ 19-20 - 2

S&F in repair PVC valve less syphonic action type low level flushing cistern coloured with inlet ball valve float and handle incl bracket 10 Lit capacity ( Make-HINDWARE CAT PART SLEEK PLUS or equivalent) fixed in repair

S&F in repair Stop valves cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions of following sizes -

15 mm 89/Rev/ 19-20 - 1

20 mm 36/LBW/19-20 - 2 89/Rev/ 19-20 - 1

S&F in repairs vitreous china water closet Indian type 580 x 440 mm white with itergal footrest including provn of lime concrete bedding including connections to flushing cistern/pipe and making good disturbed portion to match existing surface complete all as directed including flushing cistern and flushing pipe

Factory made steel window with side hung shutters incl projecting type hinge with steel handle and steel peg stay complete with glazing bars dovetailed or welded incl. taking down old window

Mild steel angle iron door frame 40x40x6mm conforming to Fe 410.0 incl.12 mm dia deformed bars( Tie bar) for strengthening at bottom of chowkhat incl.cutting floor to accommodate strengthening bar & making good in PCC(1:2:4) type B0.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Fe-290 Gde E-165 including necessary welding etc. and fixed in position.

Demolition of RCC concrete as in man hole covers 36/LBW/19-20 - 0.50 89/Rev/ 19-20 - 0.50

M/L for precast RCC 1:2:4 type B 1 using 20 mm graded stone agg for mainhole cover incl placing and setting in CM (1:6) all as specified. 36/LBW/19-20 - 0.50 89/Rev/ 19-20 - 0.05

M & L TMT bar 10 mm dia and over cut to length bent to shape required including cranking bending and binding with mild steel wire (annealed ) not less than 0.9 dia off confirming to grade Fe 310 all as specified.

M&L for brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in cm 1:6 36/LBW/19-20 - 2.00 89/Rev/ 19-20 - 11.00 79/Rev/19-20 - 9.00

M&L for half brick wall built in cement mortar 1:4 for partition wall / supporting walls for shelves complete all as specified.

79/REV/19-20 Excavation in trenches n.exc 1.5m wide & n.exc 1.50m in depth for foundation , etc or for shafts, wells, cess pits, man holes,pierholes etc n. exc 10 sqm on plan & getting out in soft/loose soil. 79/Rev/19-20 - 3 89/Rev/19-20 - 15

M&L PCC 1:4:8 Type D2 (40 mm graded aggragate) as in fdn, filling and mass concrete. 79/Rev/19-20 - 0.50 80/Rev/19-20 - 5.00 89/Rev/19-20 - 0.50

M&L Granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

S&F framed work as n doors or gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil. 79/Rev/19-20 - 90.00 80/Rev/19-20 - 80.00

M&L providing pre cast cement concrete block or slab 150mm thick 1:2:4 type B1 using 20mm graded stone aggregate with plain or inter locking joints as directed set in CM 1:6. kerbing/edge block to hard standing/footh including necessary earth work. 79/Rev/19-20 - 2.00 80/Rev/19-20 - 0.50

M&L for 100mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in sub base to floor finished fair & even all as specified and directed by Engineer-in-charge. 79/Rev/19-20 - 90.00 80/Rev/19-20 - 65.00

M&L Precast Interlocking tiles with bullnosed edge jumbo popodoro PVC moulded of 60mm thick M 35 grade epoxy coated set, jointed and pointed in dry sand over 25mm thick sand cushion. 79/Rev/19-20 - 90.00 80/Rev/19-20 - 65.00

Removing excavated material(soil) to the distance as specified and depositing where directed at a level not exc 1.50mtr above the starting point:-

Lead not exceeding 50M. 79/Rev/19-20 - 13.50 80/Rev/19-20 - 27.00

Lead exceeding 250M but not exceeding 500M. 89/Rev/19-20 - 8.00

M&L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as directed by Engineer-in-Charge.

Earth filling under floors including spreading, levelling, watering and well ramming in layers not exc 25 cm thick. Note :- Soil obtained from excavation under item 74 here-in-before shall be used for filling. 79/Rev/19-20 - 3.00 89/Rev/19-20 - 1.00

80 REV/19-20/Q3W Excavating in post holes (or similar holes) each n.exc 0.50 cum,getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

S&F rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' all as specified and directed by EIC.

Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.

Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.

S&F Mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other,or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long

S&F MS Pipe of any dia as directed by engr in charge medium grade fixed as in vertical posts etc complete

S&F MS Plate with necessary drilling holes & welding etc complete

83/REV/19-20/Q3W Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thich screed bed in cement mortar 1:4 all as directed by Engineer-in-charge.

All as per item No 88 above but on vertical surfaces of wall etc over 10 mm thick rendering in CM 1:4 all as specified and directed by Engineer-in-charge

Returning,filling in, including spreading, levelling watering and well ramming in layers n.exc 25 cm in hard/dense soil.

M&L for 75mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base to floor finished fair & even all as specified and directed by Engineer-in-charge.

M&L rendering 15 mm thick in CM(1:6) on brick walls or concrete surface, surface finished even and smooth without using extra cement complete all as specified.

M&L for 30mm ( average thickness ) PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in floors and surfaces finished fair & even.

S&F Coloured Glazed ceramic tiles (300x200mm) x 7mm thick, in floors etc.in the combination of light and dark shed concept . set & jointed in neat cement slurry & pointed in white/coloured cement to match over 10mm thick plaster in cement mortar (1:4)

M&L for reinforced cement concrete (nominal mix) 1:1½ :3 type A1 using 20 mm graded stone aggregate in lintels upto 1.5m clear span, seismic and other similar bands, lintel bands, plinth bands, roof bands and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

S&F TMT bar 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified .

S & F Solid PVC frame ( single rebated ) of size 60mmX 30MM made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws compelete as specified ( Note;- door frame shallbe water proof , termite proof ,elegent and should have excellent screws holding stength to fix hinges and hold doors properly a long life ) . Make Rajshree Plastic wood or equivalent as approved by GE.

S&F Factory made solid PVC Moulded door shutter 28 to 30mm thick (stiles) with Particle board core ,with 2,4,or 6 raised panel design with 2 mm thick moulded Prelam PVC Sheet on the front face and 2mm thick Prelam PVC sheet on Back Face.Including 15 mm thick lipping on hinge side door edge , and 10mm lipping on rest side of door shutter as per specification & drawing.

Aluminium Powder coated frame fixed type with aluminium section weighing 0.55 Kg/Mtr incl. necessary joining, cleats, glazing clips, rubber packing anodised aluminium snap beading, screws etc and including beading for fixing of stainlesssteel wire mess complete all as specified( SS wire mesh shall be measured and paid seperately in respective item)

S&F Figured glass 5.0mm thick, pin head type & glazing with snap beading and rubber beading in squares exc 0.5 sq.m in each pane

S&F fancy type pillar tap, cast copper alloy with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore.

S&F fancy type chromium plated two way bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm bore.

M&L Salt-glazed stoneware gully traps, square or round mouthed, type `P' 100x100mm

S&F vitreous china wash hand basin white of size 550x400mm flatback excluding taps, waste, chain and plug but including brackets including cutting for and pinning in ends of brackets or erecting stand complete.

S&F Waste fittings 32mm bore, brass, CP for glazed ware sinks, basins, etc. with long screwed shanks & fly-nuts, flange end bedded in red lead cement & other end

M&L for new galvanised steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors of following sizes :-

15 mm bore

20 mm bore

S &F Rotational moulded polyethylene water storage tanks 500 Ltr (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR part - I and directed by Engineer in Charge.

S&F Ball brass valves 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule

Soap dish brass CP

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

S&F PVC (SWR) bends any radius 110mm dia

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia

S&F PVC (SWR) vent cowl 110mm dia

S&F vitreous china wash down water closet pan ( Pedestal pattern ), white including connection to drain (or outgoing pipe) and to flushing pipe,anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete.

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement

M & L for cement concrete ( 1:2:4 ) type B1 using 20 mm graded stone aggregate as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement Note : Forming fair finished channel for drain using extra cement will be measured and paid for separately.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and directed by Engineer-in-charge.

S&F salt glazed stone ware drain pipes of 150mm bore, grade `A', ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

Cutting into existing manholes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150 mm bore pipe.

M&L for reinforced cement concrete (nominal mix) 1:1½ :3 type A1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement.

The surface shall be painted with one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384. A layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.5 Kg/m2 reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions. and finally applying one coat of bitumen @ 1.2 kg/sqm on APP membrane before application of aluminium paint

M&L one coat of aluminium paint over APP Membrane all as specified and directed by Engineer -in - chage

S&F glass shelf of best quality all as specified and directed

S&F glass corner of best quality all as specified and directed

36/LBW/19-20 (E/M Portion) M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators as required for the following :-

One light / fan controlled by one switch. 36/LBW/19-20 - 26 89/Rev/19-20 - 9

One socket outlet 6 amp controlled by one switch on the same board with other switches. 36/LBW/19-20 - 4 89/Rev/19-20 - 1

One socket outlet 6 amp controlled by one switch on indepdendent board.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets as required for one 16 amp socket outlet point controlled by one switch on independent board. 36/LBW/19-20 - 6 89/Rev/19-20 - 1

Supply&.Fixing Switch piaon type 230/ 250V grade on top covers (catered in point wiring above) :-

S&F switch piano flush button single pole one way 6 amp complete. 36/LBW/19-20 - 36 89/Rev/19-20 - 10

S&F switch piano flush button single pole one way 16 amp complete. 36/LBW/19-20 - 6 89/Rev/19-20 - 1

S&Fixing only Socket outlet multipurpose use flush mounting type, 230/250 Volts grade(ISI Marked) on top covers (catered in point wiring above) :-

S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete.

S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete.

S&F ceiling rose 3 plates polycarbonate body complete.

S&F Lamp holder insulated body with back plate for batten fitting. Make Anchor/bajaj/philips

Supply & fix BATTEN, LED Light fittings 1 x 20 W ,240 volt( size-4 feet/1136 mm) long life, surface/wall mounting IP 20, luminaire per watt (Minium) extruded alluminium housing with frosted PMMA diffuser with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Siska CAT part No SSK-T5-22W or equivelent model in Bajaj/Wipro/ Philips/CG /Surya roshni 36/LBW/19-20 - 10 89/Rev/19-20 - 02

All as per item No 161 here in before, but LED light fitting 1 x 8/10 W ,240 volt( size-2 feet) Make - Siska CAT part No SSK-RA-0801-N or equivelent model in Bajaj/Wipro/ Philips /CG /Surya roshni

Supply and fix heavy duty exhaust fan 300 mm size ,220/240Volt steel body, 1400 RPM with mounting ring and louvers.including three core flexible PVC insulated multi stranded copper conductor cable of size 1.5 sqmm from ceiling rose/connector to fan Make:- Havells, Model No- turbo force or equivalent of Bajaj/CG Note:- Old retrived ceiling fans sholud be deposite in MES storeyard. 36/LBW/19-20 - 04 89/Rev/19-20 - 01

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with SPN, 240 volts, 12 ways. ratings & ways. Make - Legrand cat ref no 507611 or equivalent in Schneider or Hager as approved.

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 amp ratings. 36/LBW/19-20 - 20 89/Rev/19-20 - 04

S&F MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of SPN 32 to 63 amp ratings. 36/LBW/19-20 - 02 89/Rev/19-20 - 01

M&L for Sub main wiring with two runs of 6 Sqmm single core FRLS PVC insulated but in unsheathed multi stranded copper conductor cable 1100 volts grade drawn through and including of 25mm dia PVC rigid conduit medium with conduit accessories and fixed to the surface of wall/ceiling as per ISI including 4.0 Sqmm PVC insulated copper conductor earth continuity wire including taking down old sub main wiring. Note : Two runs of copper conducter and one run of earth copper conducter and one run of PVC conduit / casing caping shall be measured as one length.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

Taking down carefully copper/ aluminum point wiring (light, fan, socket or power) complete including all fittings such as switches, ceiling roses, pendants, sockets, lamp holder, fan regulator brackets light fittings tube light fitting, bell/ buzzer etc (excluding fans) and making good disturbed surfaces of wall floors, ceiling etc complete all as specified and as directed by Engr-in-Charge to match with existing

89/REV/19-20/Q3W S&F Socket, piano type 230/250 volts :- make: Anchor/kinjal/bajaj

Socket 05 Amp rating Make- Anchor Cat pt No-14304

Socket 15 Amp rating

M&L Ceiling rose surface bakelite 65x50mm, three terminals.Make Anchor/Legrand/Crabtree

Supply & fixing Energy saving new generation 9 W CFL IP -65 Bulkhead luminare with opal diffuser complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size

Supply & fixing Mirror surface mounted LED fitting 14 W (2 Feet)provided with a high output PMMA diffuser for glare free light , IP 20 with high brightness LEDs complete with all accessories pre-wired twin core twisted flexible copper conductor cable with suitable size. Make - Crompton cat pt No- LCL-14-CDL or equivelent model in Bajaj/Havells/ Philips/Wipro/Siska /Shakti fixture

S&F in repair factory made, sheet distribution boards, SP&N 8 ways, double door protection class IP-42 double door type suitable for mounting MCB/ MCCB, confirming to IS-13032, IS-8623, BS-5484 with minimum 200 amps, copper bus bar of the under mentioned rating :-

M & L for Supplying, laying, connecting and testing in trenches, under floors/ roads or on walls Cable XLPE insulated screened PVC bedded galvanized steel strips or wire armored, electric power cables (heavy duty) ISI marked with stranded aluminium conductor, 1100 volts grade, of size 10 sqmm, 2 core .

Excavation in trenches n.exc 1.5 metre wide and n.exc 1.5 metre in depth for foundation etc or for shafts, wells, cess pits, manholes, pier holes, laying cables errection of poles / struts/stays etc n.exe 10 Sqm on plan not exceeding 1.5 metre in depth and getting out in any type of soil.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm in any type of soil.

Removing of excavated material (soil) to a distance n.exc 50 metre and depositing where directed at a level n.exc 1.50metre above the starting point

M & L Sand cushioning to PVC under ground cable with screened and washed sand and punning to provide a required cover.

M&L bricks for protection cover to under ground cable (with old size sub class `B` bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10 mm as directed by Engineer in-charge

M/S ROHIT CONSTRUCTION

GS BUILDERS AND ENGINEERS

KARNI CONSTRUCTION COMPANY

J.J.ENGINEERING

Sh Manoj Nagar

M/S Dinesh Chandra Mittal