Widening and strengthening of Maudaha Biwar Jalalpur Kupra Road (MDR-55B) in Km-15.00 to 19.600 (Length 5.600 Km.)

Amount

Excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m

Compacting original ground supporting sub-grade Loosening of the ground upto a level of 500 mm below the sub-grade level, watered, graded and compacted in layers to meet requirement of table 300-2 for sub-grade construction.

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. (Carted earth)

Construction of granular sub-base by providing granular material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 (By Mix in Place Method)

Wet Mix Macadam (Plant Mix Method) Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density (As Per Clause 406-4.14)

Providing and applying primer coat with SS1 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sum using mechanical means. As per MORT&H Clause 502- 5.01

Providing and applying tack coat I with bitumen emulsion using emulsion pressure distributor at the rate of 0.25 kg per sum on the prepared bituminous surface cleaned with mechanical broom. As per MORT&H Clause 503

Dense Graded Bituminous Macadam Grading -I Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 Percent by weight of total mix and filler, transporting the hot mix to work site, laying with ahydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects.

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 Percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specificationclause No. 507 complete in all respects

Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Construction of sub grade and earthen shoulders with approved materials obtained from boorrow pits with all lifts & leads, transporting to site, spreading, grading to required slop and compacted to meet requirement of table No. 300-2 Patri

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.As per MORTH Data Book & Specification clause 15.01-304 B-1

Sand Filling in Foundation Trenches as per Drawing & Technical Specification.As per MORTH Data Book & Specification clause 15.03-304

Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications.PCC Grade M-15 using batching plant & manual placing.As per MORTH Data Book & Specification clause 15.11(1500,1700&2100) case -II

Brick Masonry Work in Cement Mortar 1:3 in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications.

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106.(1000 mm Dia)

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106.(600 mm Dia)

Plastering with cement mortar (1:3 ) on brick work in sub-structure as per Technical Specifications

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications. As per MORTH Data Book & Specification clause 15.13(1600)

Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications.As per MORTH Data Book & Specification clause 15.14(2706&2200)

Plain/Reinforced Cement Concrete for wall & slab etc. complete as per Drawing and Technical Specifications.RCC Grade M-25 using batching plant,Transt Mixture & Concrete Pump.As per MORTH Data Book & Specification clause 15.12(1500,1700&2100) B

Providing and laying Filter material underneath pitching in slopes complete as per drawing and Technical specification.As per MORTH Data Book & Specification clause 16.05-2504

Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications.As per MORTH Data Book & Specification clause 16.04-2504

Providing and Laying of Rubble moulded Zig Zag Interlocking Concrete Block Pavements having thickness 80 mm as per drawings and Technical Specification Clause 1504.

Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications.RCC Grade M-20 using batching plant,Transt Mixture & Concrete Pump.As per MORTH Data Book & Specification clause12.08(C)case -II

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer- in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).AS per DSR No.-16.69

Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.

Providing and laying of hot thermoplastic compound 2.5 mm thick including reflect rising glass beads @ 250 gms per sqm area thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC-35 the finished surface to be level uniform and free sleek and holes, Zebra Line

Providing and fixing of Retro Reflective sign board size 1200x900mm made of 2 mm alloy aluminium sheet and 4 mm thick APC sheet fully covered with intensety retro reflective sheet having approved massage fully proceed by AVERY DENSION CO. (U.S.A.) equivalent equipment as per specified brand back of aluminium sheet will be provided frame 35x35x5 mm angle iron painted with two coat smoke grey of sky blue paint. Leg 75x40 mm channel, 3 meter long complete (size 1200x900mm) 1.08 sq mtr)

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing Stop Board

Providing and laying of hot thermoplastic compound 5mm thick including reflect rising glass beads @ 250gms per sqm area thickness of 5mm is exclusive of surface applied glass beads as per IRC-35 the finished surface to be level uniform and free sleek and holes. (Repeated bars in Abadi Portion)

Supply of Retro Reflective Sign Board size 1200x900mm made of 2mm alloy aluminium sheet and 4mm thick APC sheet fully covered with intensity retro reflective sheet having approved massage fully proceed by AVERY DENSION CO (U.S.A.) equivalent equipment as per specified brand back of aluminium sheet will be provided frame 35x35x5mm angle iron aluminium sheet painted with two coat smoke grey or sky blue paint leg 75x40mm channel 3 mtr long complete. (Size 1200x900mm) (Both Side 1.08 sqm mtr) TRAFFIC SIGNS - MAXIMUM SPEED LIMIT

6 M Span over Head Cantilever Structure with 300 dia M S one vertical post Supply, fixing & erection of built up Cantilever Structure of 6m span comprising of one vertical posts of 6.00 m height made up to 300 mm NB heavy class MS pipe as vertical member welded with 10 mm MS plate at top & 12 mm M S plate at bottom. The horizontal truss shall comprise of 50 mm dia heavy class M. S. pipe and 40 mm dia heavy M S pipe as bracing & 10 mm MS plate at bottom for fixing to vertical post as per structure design & drawing with one of steel primer and two coats of synthetic enamel plant. The work includes construction of RCC Foundation of size 0.90x0.90x1.50 m of required depth as per site condition for built up structure including Earth work in excavation 100 mm thick lean concrete

Retro Reflective Sheetingtype -IV with 4 mm thick ACM Single Side Providing and fixingof reflective signs with a corrisions ressistant 4 mm thick with 0.4 mm to 0.5 mm both sidealuminium skin Aluminium composite pannel…etc as per lucknow circle SI no.10 Morth-801

Supply of Retro Reflective Sign Board size 1200x900mm made of 2mm alloy aluminium sheet and 4mm thick APC sheet fully covered with intensity retro reflective sheet having approved massage fully proceed by AVERY DENSION CO (U.S.A.) equivalent equipment as per specified brand back of aluminium sheet will be provided frame 35x35x5mm angle iron aluminium sheet painted with two coat smoke grey or sky blue paint leg 75x40mm channel 3 mtr long complete. (Size 1200x900mm) (Both Side 1.08 sqm mtr) TRAFFIC SIGNS - Single Hzard

Supply of Retro Reflective Sign Board size 1200x900mm made of 2mm alloy aluminium sheet and 4mm thick APC sheet fully covered with intensity retro reflective sheet having approved massage fully proceed by AVERY DENSION CO (U.S.A.) equivalent equipment as per specified brand back of aluminium sheet will be provided frame 35x35x5mm angle iron aluminium sheet painted with two coat smoke grey or sky blue paint leg 75x40mm channel 3 mtr long complete. (Size 1200x900mm) (Both Side 1.08 sqm mtr) TRAFFIC SIGNS - Single Chevron

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing (As per Lucknow SOR).Caution Board 80 x60 mm rectangular with diffinitation plate (20 x 60 cm)

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing (As per Lucknow SOR).90 cm Equilateral tringle with diffinitation plate size (20 x 60 cm)

Maintainance Charge including @ Earth Work, repair of painted surface, Earth Work on patri, Culvert, Road Furniture etc as per Direction of E/I for the period of Five Year from the actual completion of work. (Excluding G.S.T.) Maintainance of First Year (@ 0.00% of Total Work Amount of 1 to 39)

Maintainance Charge including @ Earth Work, repair of painted surface, Earth Work on patri, Culvert, Road Furniture etc as per Direction of E/I for the period of Five Year from the actual completion of work. (Excluding G.S.T.) Maintainance of Second Year (@0.25% of Total Work Amount of 1 to 39)

Maintainance Charge including @ Earth Work, repair of painted surface, Earth Work on patri, Culvert, Road Furniture etc as per Direction of E/I for the period of Five Year from the actual completion of work. (Excluding G.S.T.) Maintainance of Third Year (@0.50% of Total Work Amount of 1 to 39)

Maintainance Charge including @ Earth Work, repair of painted surface, Earth Work on patri, Culvert, Road Furniture etc as per Direction of E/I for the period of Five Year from the actual completion of work. (Excluding G.S.T.) Maintainance of Fourth Year (@0.75% of Total Work Amount of 1 to 39)

Maintainance Charge including @ Earth Work, repair of painted surface, Earth Work on patri, Culvert, Road Furniture etc as per Direction of E/I for the period of Five Year from the actual completion of work. (Excluding G.S.T.) Maintainance of Fifth Year (@1% of Total Work Amount of 1 to 39)

M/s S.S. ASSOCIATES (BID ID -5738768)

VINAY KUMAR (BID ID -5737834)