Construction and Renovation work of New Building at Government Polytechnic, Sahibganj for Developing it as a State of the Art Institution

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume)

Providing coarse clean sand in filling in foundation trenches or in plinth including thick with all leads and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted voume)

Providing designation 75b work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.m. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials ranking out joints to 15mm depth, curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75Bbrick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I.

1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Foundations, footings, bases of columns, etc. for mass concrete Weather shade, Chajjas, corbels etc., including edges

Add for using extra cement in the items of design mix over and above the specified cement content therein.

S/F 35mm thick solid core type non-decorative single leaf flush door and windows with black board core banded with high quality phenol formaldehydes synthetic resin both side commercial veneered of standard make with oxidized iron fittings such as hinges, sliding door bolts tower bolts, handles or rings hooks and eyes, cleats sand block as per schedule taxes and royalty all complete as per building and direction of E/I.

Supplying, fitting & fixing 35mm thick solid core type non-decorative double leaf flush shutter in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneeres of standard makew with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing average 150mm thick dry rammed khoa beaten to112mm.(compacted with water) made of well burnt or jhama bricks including ramming properly till compacted thckness is achieved, curing and carriage of water with all leads,making proper slope and blending the top with cement morter (1:10) all complete as per building specification and direction of E/I

Providing plain M.S. reinforcement of 6mm dia roads as per approved design and drawing excluding carriage of M.S. roads (Straight or in coils) to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.

Providing TMT steel reinforcement 8mm dia rods to 12mm dia as per approved design and drawing excluding carriage of M.S. roads (Straight or in coils) to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.

8 mm to 32 mm dia (TMT coil Fe 500) (Only Valid for SAIL & TATA Steel)

(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

(c) 16mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

S/F M.S. grill made of 20 x 6mm M.S. flat as per approved design and drawing, properly fabricated with joints continous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction ofE/I. (Where materials is not supplied by the deptt.)

Providing and fixing fan hook of 16mm dia TMT M.S. bar I meter long bent to required size and shape placed in position and fixed in RCC slab/beam at the time of casting all complete as per building specification and direction of E/I.

S/F local make collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat disgonal 30 x 3mm, with top and bottom rails of T iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts nuts locking arrangements steppers handles including applying a priming coat of red lead paint carriage hoisting and taxes all complete as per building specification and direction of E/I.

S/F local make fully glazed steel door, windows or ventilation of standard rolled 'Z' and mullion steel section and size as per IS - 38 joints met welded with 100 x 16 x 3mm M.S. lug fixed in cement concrete (1:2:4) blocks, 15 x 10 x 10cm size including cost of oxidized iron fitting with hinges, handle per step catch springs, 3mm thick plain glass panes with aluminum beads and inner frame fixed with lugs with 20mm long 6.3mm GI. counter sunk machine screw and nuts and applying a coat red lead paint carriage to work site hoisting and plcing in all position in all storys and taxes all complete as per building specification and direction of E/I.

Providing designation 75A one brick flat soiling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 20 guage G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing designation 75b one brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. (iv) 600X600 mm size

Providing and laying 15mm to 23mm thick kotah stone tiles in risers of step, skirting and pillars of approved size texture and colour laid over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing to granolilthic finish with approved quality of carborandom stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Fine Dressing of Ground as per instruction and specification of E/I

Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 12mm thick cement plaster (1:6) -with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty as per building direction of E/I.

Providing 1.5mm cement punning including curing carriage of water with all leads and lifts as per building specification and direction of E/I.

Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastrered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over old surface including washing cleaning and preparing the walls scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales, smokes, grease and sand preparing, including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specificatio).

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Dismantling pucca brick or lime work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down chaukhats in doors including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking sown chaukhats in windows including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing 250mm wide brick drain in cement mortar (1:6) with as. 150mm clear depth and 250mm apron including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

providing 150mm wide brick draing in cement mortar (1:6) with av. 150mm and 125mm apron including stacking serviceable material within 15M lead and disposal of unserviceable material with all leads all complete as per direction of E/I.-

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20mm nominal size ) over 75mm bad by dry brick ballast 40mm nominal size well rammend and consolidated and grouted with fine sand including finishing the top smooth.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece

Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, ailings, brackets, gates and similar works

for grading- I Material

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) 25mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado andpillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3coarse sand) and jointed with grey cement slurry mixed with pigment tomatch the shade of the slabs, including rubbing and polishing complete

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and laying Double Charge vitrified floor tiles in Different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confirming to IS 15622/ISO 13006, of approved make , in all colour and shades laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointed with grey cement [email protected] kg /sqm including grouting the joints with white cement and matching pigment etc.Size of tiles 600x600mm

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.Rate per cum for grading-I Material

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler - 110mm

Single tee without door - 75x75x75 mm

Single tee without door - 110x110x110 mm

Bend 87.5° - 75 mm bend

Bend 87.5° - 110 mm bend

Bend - 110mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete .Cllip 110mm

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm overand including priming coat of exterior primer applied @ 2.20kg/ 10 sqm)

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surfaceto prepare the surface even and smooth complete. sqm 89.65

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) - Powder coated aluminium (minimum thickness of powdercoating 50 micron)

Providing and fixing 100mm brass locks (best make of approvedquality) for aluminium doors including necessary cutting and makinggood etc. complete.

Providing and fixing factory made single extruded WPC (WoodPolymer Composite)soliddoor/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (woodpowder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

25 mm thick

Water proofing for old and New Roof slab:- Providing and laying water proofing treatment on roof slab by applying two Component, factory………………E/I.

Covering of treated surface with PCC:- Providing 25mm thick Cement concrete M-20 (1:1.5:3) maintaing slope in alternate 2 Mtr. X 2Mtr. Panels with approved quality of stone chips of 20mm to 6mm Size graded and cleaned sand of F.M. 2.5 to 3 including screening................E/I.

Providing and filling of 6mm thick Groove between 25mm PCC panels with Polysuplhide sealant (Poring Grade) as per drawing and techinical speicifcation and direction of E/I.

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions.

The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.)

Bricks Lead = 1 k+7 P(8km)

Fly Ash Brick - 15km

Sand lead = 10 km

Stone chips lead = 22 km

Stone metal lead = 22 km

Local Sand lead = 3km

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.In case the cement content in design mix is more than 1.10% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 75 A brick work in C.M. (1: 6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 125mm thick reinforced designation 75A brick work in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement0 all complete as per building specification and direction of E/I.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100 mm nominal size dia

Providing and fixing factory made single extruded WPC (Wood Polymer Composite)soliddoor/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge),minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

With float glass panes of 4.0 mm thickness

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in?charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Supplying, filling, spreading & leveling stone boulders of size range5 cm to 20 cm, in recharge pit, in the required thickness, for allleads & lifts, all complete as per direction of Engineer-in-charge

Supplying, filling, spreading & leveling gravels of size range 5 mm to10 mm, in the recharge pit, over the existing layer of boulders, inrequired thickness, for all leads & lifts, all complete as per directionof Engineer-in-charge

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mmto 2 mm in recharge pit, in required thickness over gravel layer, for all leads& lifts, all complete as per direction of Engineer -in-charge

DT : Basic rates for 125/115mm dia drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH rig Machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of E/I.. (Basic Rates) Drilling upto 30 mtr. Depth below G.L. in Rural Area

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size GI box and earthing the point etc as required

Group A

Group B

Group C

Twin Control Point Wiring in PVC Conduit, with Modular type Switch: Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, 2 way modular type switch, modular plate, suitable size GI box and earthing the point with 1.5 sq mm. FR PVC insulated copper conductor single core cable etc as required

Power Plug Wiring in PVC conduit(2x4 sq. mm): Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit alongwith 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sqmm earth wire

2 X 4 sq. mm + 1 x 4 sq.mm Earth Wire (Sockets)

4x6 Sqmm + 2x6 sqmm earth wire

4x10Sqmm + 2x10sqmm earth wire

4 X 16 sq. mm + 2 x 6 sq.mm Earth Wire

S/F piano type switch/socket - Supplying and fixing following piano tyep switch/socket on the existing switch box/cover including connections etc. as required.

5/6 amps, one way switch

3 pin 5/6 amps, socket outlet

S/F Modular type switch socket - Supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required

5/6 amps, one way switch

5/6 amps, 3 pin socket outlet

Telephone socket outlet

TV antenna socket outlet

S/F Modular type electronic fan regulator: Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

S/F Modular type blanking plate :-Supplying and fixing modular blanking plate on the existing modular plate & switch box but excluding modular plate as required.

S/F Modular boxes, base & cover plate :-Supplying and fixing following size/ modules G.I. box along with modular base & cover plate for modular switches in recess etc as required.

4 module (78mm x 140mm x 50mm)

6 module (78mm x 205mm x 50mm)

8 module (78mm x 230mm x 60mm)

12 module (135mm x 205mm x 60mm)

S/F light plug point with piano type accessories - Supplying and fixing suitable size G.I./PVC box on surface or in recess with phenolic liminated sheet cover in front including providing and fixing 5 pin, 5/6 amps socket outlet and 5/6 amps piano tyep switch connection, painting etc. as required.

S/F Light plug Point with Modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc as required.

S/F Power plug Point with Modular type accessories: Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch connection, painting etc as required.

S/F Ceiling Rose: Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooen block including connection etc as required. Make :- Anchor / Kona / Kany

S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required.

ITC fluorescent fitting directly on surface :-installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, directly on ceiling / wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper cond.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F busbar chamber - Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty, complete with all accessories including connections, earthing the body, etc. as required.100 amps

Supplying and Fixing TPN MCB DB: Supplying and Fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder including painting, earthing etc. as required( without MCB/RCCB/ISOLATOR). Make :- Havells / Standard / indoasian.

4 Way ,(4+12 ), double door Horizontal type

6 Way (4+18) Double Door, Horizontal type

S/F 'B' series, S.P. MCB - Supplying and fixing 6 amps to rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commossioning etc. as required.6/32, single pole, "B" series

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make :- Havells / Indoasian / Standard.6/32A Single Pole.6/32A Single Pole

6/32A rating, SPN MCB, "C" curve 10 KA breaking capacity.

40A rating, TPN MCB, "C" curve 10 KA breaking capacity.

63A rating, TPN MCB, "C" curve 10 KA breaking capacity.

Supplying and fixing following rating four pole, (three phase and neutral) 415 volts, residual circuit breaker (RCCB) having a sensitivity current 30 milli amperes in the existing MCB DB complete with connection, testing & commissioning etc. as required.

S/F 20amps SPN MCB industrial Socket:-Supplying and fixing 20 amps 240V, SPN industrial socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB insheet steel enclosure on surace or in recess with chained metal cover for the socket outlet and complete with connections, testing & commissioning etc.

Copper earth pipe electrode :-Earthing with G.I. earth pipe 4.5mtr. long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt as required.

G.I. earth plate electrode - Earthing with G.I. earth plate 600mm 600mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (with charcoal or coke and salt)

Copper earth plate elecrtode - Earthing with copper earth plate 600mmx 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. as required (But with charcoal or coke and salt)

Including Royalty etc@ Rs. 27.48 per cum, cost of watering, rolling & compaction.

S/L 8 SWG copper wire:- Supply and fixing 8 SWG cpper wire at 0.50 metere below ground level for coductor earth electrode including soldering etc. as required.

S/L 25 mm x 5 mm G.I. earth strip in ground :-Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including soldering etc.

P/F 25 x 5mm copper earth strip in pipe :-Providing and fixing 25mmx5mm cpper earth strip in 40mm & 4.5Mtr long G.I.pipe for earth electrode etc. as required.

P/F 25mm x 5mm copper earth strip in surface/ recess :-Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc., as required.

P/F G.I. lightning conductor finial - Providing and fixing of lightning conductor finial, made of 25mm dia 300mm long, G.I. tube, having single prong at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required.

P/F G.I. lightning conductor tape in horizontal run - Providing and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

P/F G.I. lightning conductor tape in vertical run - Provding and fixing G.I. tape 20mm x 3mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

MV Cable Laying upto 25 Sq mm in ground:- Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc, as required.

MV cable laying upto 120 sq.mm. in ground - Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm. but not exceeding 120 sq.mm. direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Above 185 sq. mm and upto 400 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Upto 35 sq. mm

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 95 sq mm but not exceeding 185 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 185 sqmm but not exceeding 400 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

3.5c x 35 sq.mm

Providing and fixing of XLPE, Aluminium Armoured PVC Cable confirming to IS IS7908 (Part-1) 1988 0f grade 1.1KV. Make:- Havells / Finolex / Polycab 1 R for each floor separately ,3.5 Core 50 Sq. mm. 1.1 KV XLPE Al. Ar. Cable from Main LT Panel to VTPN L.D.B Panel.

Supplying PVC/XLPE insulated PVC sheathed, heavy duty, armoured electrical cable with aluminium conductor- 3.5 core, 95 sq.mm

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding not 35 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one nùmber PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 35 sq mm but not exceeding 95 sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

1.1 KV Cable End Termination:- Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following size of PVC insulated XLPE Al. Ar. Cable of 1.1 KV grade as required.

Supply of LED Street light (45/48W)

70W LED street light

3.5c x 35 sq.mm (32mm)

3.5c x 50 sq.mm (35mm)

3.5c x 150 sq.mm (50mm)

3.5c x 185 sq.mm (57mm)

3.5c x 240 sq.mm (62mm)

3.5c x 70 sq.mm (38mm)

4c x 16 sq.mm (28mm)

4c x 10 sq.mm (25mm)

S.I.T.C of following rating recess/surface mounting round/square shape downlight with pressure die cast housing for single phase supply voltage. Luminaire shall conform to IS:3022 part-5/ section-5 or IEC:62722 with all necessary accesories as required.

80W LED Flood light

150W LED Flood light

S.I.T.C of following rating recess/surface mounting round/square shape downlight with pressure die cast housing for single phase supply voltage. Luminaire shall conform to IS:3022 part-5/ section-2 or IEC:62722 with all necessary accesories as required.

Supply fitting fixing of Recess Mounting LED Round Down light (12W)

2' X 2' LED Panel Light (34W)

S.I.T.C of following rating surface mounted LED tube lightfitting suitable for 230V 50Hz, single phase supply etc. complete as required.20w/22w LED tube

Supply and installation of Ceiling fan 48" (1200mm)

Supply, fitting, fixing and testing of 1200mm Sweep, BLDC, 5Star Fan.32 W

S.I.T.C of following rating approved make LED bollard fitting with cylindrical shape and inverted cone shape head of height 600 to 850mm power input 8/9 watt with die cast aluminium housing opel with PC diffuser, IP:65/54 protection, conferming to IS:10322 part 5 etc all complete as required. (excluding plinth charges)

12" (300mm) Exhaust fan

Supply of 9/10 Watt LED Bulb

Providing and fixing of XLPE insulated, aluminium armoured cable including termination. Make:- Havells / Finolex / Polycab

3.5X70 mm2, 1.1kV

3.5c x 150 sq.mm

3.5c x 185 sq.mm

9/10 Watt LED Bulb

Supply fitting fixing of Bulk head fitting with 9/10 watt CFL/LED

Supply of 12" 300mm metal exhaust fan

16" (400mm) Wall fan

Silent type D.G Set of capacity 100 KVA With AMF Panel IS/IEC-60034- 1 IS: 1460 IS: 13018

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

SITC of 2x20W LED Tube light.

7 Oil (Fuel) Filter for 30 to 60 KVA D$set

Mobil Filter for 30 to 50 KVA DG set

Air (inner + outer) Filter for 30 to 60 KVA DG set

SMPS 12V Battery charger for DG se

MAIN DISTRIBUTION LT PANEL FOR PRINCIPAL QUARTER

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Main LT Panel fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

The Main LT Panel shall broadly comprise of the following equipment/components)

Incoming Feeders:-

Incomer-63A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 1 No.63A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 1 No. (Changeover)

Outgoing Feeders:-

63A TPN MCB 10kA - 03 Nos.

100A TPN Copper bus bar in metal encolsure with fixing clamps

Indication lamps(On- Off Trip Power On -- RYB)

Supplying, Installing, Testing & Commisioning cost of Main LT Panel for Principal quarter building all complete with all necessary items as per direction of E/I.

Lift Panel : The panel includes 415V, 100A, 3Ph, 35kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character:

Incomer

1 No. 63A/FP/ MCB

Bus bar -100A, 16kA AL

Outgoing

40A ,4P, 30mA RCCB- 1 no

40Amps, TPN, MCB -1 no

16 Amps, DP MCB -1 no

16 Amps, DP RCCB -1 no

Lift Panel : The panel includes 415V, 100A, 3Ph, 35kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium, Earth Bus for main supply, removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 2.5 ,4, Sq mm PVC Cu. wire. All incomer MCCB and bus coupler shall be mechanically operated . All 4 pole MCCB with thermomagnetic based release must have following character:

Incomer

1 No. 63A/FP/ MCB

Bus bar -100A, 16kA AL

Outgoing

40A ,4P, 30mA RCCB- 1 no

40Amps, TPN, MCB -1 no

16 Amps, DP MCB -1 no

16 Amps, DP RCCB -1 no

MAIN DISTRIBUTION BOARD FOR 400 BEDDED HOSTEL BUILDING

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Main Distribution Board fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

The Main Distribution Board shall broadly comprise of the following equipment/components)

Incoming Feeders:-

Incomer- 250A, TPN MCCB (P-2), 35 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 1 No. (AC Mains) 100A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 2 Nos. (DG OG + Changeover)

Outgoing Feeders:-

63A TPN MCCB 16kA - 02 Nos.

40A TPN MCB 10kA - 20 Nos.

63A TPN MCB 10kA - 28 Nos.

300A TPN Copper bus bar in metal encolsure with fixing clamps

Indication lamps(On- Off Trip Power On -- RYB)

Supplying, Installing, Testing & Commisioning cost of Main Distribution Board for 400 Bedded Hostel building all complete with all necessary items as per direction of E/I.

MAIN DISTRIBUTION BOARD FOR SRC BUILDING

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Main Distribution Board fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

The Main Distribution Board shall broadly comprise of the following equipment/components)

Incoming Feeders:-

Incomer- 250A, TPN MCCB (P-2), 35 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 1 No. (AC Mains) 100A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 2 Nos. (DG OG + Changeover)

Outgoing Feeders:-

Outgoing Feeders:-

40A TPN MCB 10kA - 10 Nos.

63A TPN MCB 10kA - 24 Nos.

300A TPN Copper bus bar in metal encolsure with fixing clamps

Indication lamps(On- Off Trip Power On -- RYB)

Supplying, Installing, Testing & Commisioning cost of Main Distribution Board for SRC cum Library building all complete with all necessary items as per direction of E/I.

MAIN DISTRIBUTION BOARD FOR 300 BEDDED HOSTEL BUILDING

Design, Fabrication, Supply, Erection,Testing and commisioning of Powder coated Indoor Type Main Distribution Board fabricated out of 14 guage CRCA sheet steel in cubical, compartmentallised, free standing , dust and vermin proof, (degree of protection-IP54)with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Cable gland plates shall be provided on top as well as bottom of the panels. Panels shall be treated with all anti-corrosive process before painting as per specification. Panels shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) as per Specification.

The Main Distribution Board shall broadly comprise of the following equipment/components)

Incoming Feeders:-

Incomer- 125A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 1 No. (AC Mains) 100A, TPN MCCB (P-2), 16 kA for 1 sec (Ics=100%Icu) Breaking capacity (Variable thermal rating 80-100%, variable magnetic rating 6-10 times) with factory made silver plated copper spreading links- 2 Nos. (DG OG + Changeover)

Outgoing Feeders:-

63A TPN MCCB 16kA - 02 Nos.

40A TPN MCB 10kA - 08 Nos.

63A TPN MCB 10kA - 18 Nos.

200A TPN Copper bus bar in metal encolsure with fixing clamps

Indication lamps(On- Off Trip Power On -- RYB)

Supplying, Installing, Testing & Commisioning cost of Main Distribution Board for 300 Bedded Hostel building all complete with all necessary items as per direction of E/I.

Supplying and fixing male ended 15 mm dia brass bib cock of approved quality (wt. not less than 350 grms) with extra socket all complete as per specification and direction of E/I.

Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I.(a) 15 mm dia

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.( Vertical type)

Horizontal - 25 mm dia

Horizontal - 32 mm dia

Providing and fixing N.P./C.P. brass/PVC procelain shower rose of 15mm inlet etc. all complete as per specification and direction of E/I.Shower Rose - 125mm

Providing & fixing 15mm size pillar cock C.I. body brass spindle pillar cock of approved quality as per specification & direction of E/I.

125 mm thick wall

250 mm thick wall

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Mirror (450 x 300mm)

soap Dish container

C.P. brass towel rail 20mm x 600mm with bracket container

Copper earth pipe electrode :-Earthing with G.I. earth pipe 4.5mtr. long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt as required.

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'P' trap 15 liters C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware ware footrest to be fixed than 50 gms, 15mm PVC connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 580mm long - With 12.5 lit. low level PVC cistern

Supplying, fitting and fixing 40mm highb viterous white glazed earthen E.W.C. with 'P' trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fitting with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stope cock of approved quality weight not less than 450 grams 15mm PVC alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic soild state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming all complete as per specification and direction of E/I. With 'P' trap - 12.5 lit low level PVC Cistern

iii) 12.5 litr with p trap

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware urinal of Hindustan 'Parry' or any other approved I.S.S. make with 5 litres capacity C.i. automatic flusing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm PVC/Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including priming coat of red oxide, cutting wall and floor making good the same etc. all complete as per specification and direction of E/I.Flat back or standard corner (600mm x 350mm)

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm PVC waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Lbour for alying, fitting and fixing NP2 R.C.C. spun pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leakproof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complet as per specification and direction of E/I.150mm dia R.C.C. spun pipe

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to150 mm measured

Polythene water storage tank of ISI mark (eg Sintex /Sinter /himgiri/gangotri etc with cover & locking system

Special type C.P. Bath room Fitting for V.I.P.Buildings(JAL, Jaquar, Mark or Equivalent)

Angular Stop Cock

TELEPHONE SHOWER

Supplying laying fitting and fixing NP2 R.C.C spun pipes all complete as per direction of E/I. 150mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

FR PVC insulated 3 core 4 sq.mm copper wire

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

a) Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart).Hedges

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).for plantation

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1km (manure measured in stacks will be reduced by 8% for payment).Same as good earth

Fine dressing of the ground

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and/or good earth to be paid seprately

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water).TREE Plants

Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 20 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Schefflera high colour having ht. 25 cm to 30 cm, well developed with fresh & healthy foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying plants Allyssum white in full bloom well developed Fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Dahlia double kenya variety in different colour well developed with 3 to 4 flowers in half bloom, good foliage stacked with Green painted Bamboo sticks, 45 to 60 cm height in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Dianthus dwarf in different colour fresh & healthy bloom in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Missbranthemum in different colour well developed with fresh & healthy foliage in full bloom in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Nasturtium in different colour well developed with fresh & healthy foliage with full bloom in 20 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge..

Providing and Displaying plants Verbina in different colour having 30 to 45 cm ht., well developed with fresh & healthy foliage in bloom condition in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Petunia hybrid different variety in different colour well developed with fresh and healthy foliage in full bloom in 25 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.

Supply and stacking of plant Cassia biflora of height 60-75 cm. with 4-5 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge..

Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Direction and Place Identification signs upto 0.9 sqm size board. (Providing and erecting direction and place identification retro-reflectorised sign asper IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing)

Direction and Place Identification signs with size more than 0.9 sqm size board. (Providing and erecting direction and place identification retro- reflectorised sign asper IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

1.5Tr. 5 Star split A.C (Inverter Type) I91391-part-I

Copper Tube of size 7f 2" for split ac tl;:ritT/7.S/2/3 tr capacity includins nitride rubber insulation

4 KVA wall mounted automadc voltage stablizer from range 140V to 280V

Drain Pipe for AC

Outdoor stand for 1.5Tr Split AC

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, as reauired. 4 Zone

Supplying installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed Tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged a)ver plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Single pair, 2-core, 1.5 sqmm

Providing, Fixing, Testing & Commisioning of 'C' Class heavy duty MS pipe conforming as per IS-1239 including all fittings such as bend, tees, elbows, reducers including one coat of synthetic priper and two coats of Red Enamel Paint for fire hydrant, Sprinkler and Fire Hose Reel System.

200mm dia

150mm dia

80mm dia

65mm dia

65mm dia

50mm dia

40mm dia

32mm dia

25mm dia.

Providing and fixing swinging type CI Non Return Valve with flap and SS hinges complete including matching flanges, nuts & bolts conforming to IS:5312

150mm dia.

80mm dia.

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PM 1.6 with non rising spindle, bronze/gun metalseat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to is /du of following sizes as required:

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304,sheet with 3 mm dia holes with stainless steel flange.

Supplying and fixing Single headed extemal yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/StainIess Steel and chain as reauired •a) Single Headed

Supplying, fixing, testing and commissioning of Butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

150mm dia.

80mm dia

65mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PM 1.6 with non rising spindle, bronze/gun metalseat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to is /du of following sizes as required: 150mm dia.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe With 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. conforminq to IS 636 (type-A) as required Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle, Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 mtr.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe couolinq as required: Gun Metal

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore

Supplying, fixing, testing & commissioning Of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts,bolts, washers, gaskets and conforming to IS 780 of following sizes as required

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way-100 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required. Air Release Valve 25mm

Providing and fixing Pressure swtich in m.s pipe line including connection etc as required.

Supply, erection, testing & commissioning of electrical motor driven main pump of horizontal In Line Type end suction pump capable to deliver 2850LPM against head of 60M (to ensure a minimum pressure of 3.5 Kg/Sqcm at the farthest or topmost Hydrant) . Fire pump shall have C.I. casing, bronze impeller (hard finished and dynamically balanced) and S.S. (304) Shaft with mechanical seal. The installation shall be complete with necessary pressure gauge with gun metal shut off cock on delivery side. (The pump should be tested for bench mark at factory and shall be gotten approved by the Local fire Authority). (HYDRANT PUMP)

HYDRANT PUMP 2280LPM,60M HEAD

Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supplywith IP 55 protection for enclosurewith F class insulation confirming to IS: 325 includingcommon base frame fabricated from min. 75X50 mm M.S channel, coupling with guard foundation bolts, pressure gauge, anti-vibration pads, cement concrete foundation etc. complete in all respect as required or as directed by engineer incharge.

JOCKEY PUMP 180 LPM, 60 M head

(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting Of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump Of iron body & bronze impeller With stainless steel shaft, confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply With IP55 class Of protection for enclosure, horiziontal foot mounted type with Class-'F insulation, to IS-325. (D) M.S. fabricated common base plate, guard,foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. Terrace pump 450 lpm, 30 M head

Manual DOL Starter (For Terrace pump) (5HP)-2 pcs

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, having switchgears and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42 with 400 Amp aluminium bus bar as required.

Fire pumps panel

Incoming

1 No. 200 Amp, TP&N MCCB

0-400 Amp digital ammeter with one set of current transformer

0-500 volt digital voltmeter with RYB indicator lamps, HRC control fuses.

Outgoing

1 Nos of 200 Amp TP&N MCCB (1 No for EDFP )

1 Nos of (suitable for 40 HP pump) DOL starter with over load protection, current sensing type single phase preventer with all accessories and internal wiring complete as required for automatic operations (1 No for EDFP)

1 sets 0-400 Amp digital ammeter and 1 sets current transformers.

Manual DOL Starter (For Terrace pump) (5HP)-2 pcs

Note:- Potential free terminal to be provided for BMS

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Devraj Mild Steel sheet Double Door with locking arrangment(4) Fire Hose Cabinet, Warranty 1 Year

Modular Passive Aeration Compact Compost Plant.

Wheel borrow of 100 litters capacity

Tri Cycle

200 Ltrs Steel Bin

Automatic Sanitary Napkin incinerator Machine.

RDF Baling Machine

Type Floating Dome Portable Bio-Methanisation Plant

75 Kl/Day Compact Sewage Treatment Plant

50 Kl/Day Compact Sewage Treatment Plant

Supplying, installing, testing and commissioning of Dome camera 1/2.8" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 50m IR, 0.001Lux, 1920x1080@30fps, 512 GB SD card slot, IP67, IK10, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal Housing Make : Pelco/Birdeye/Axis

Supplying, installing, testing and commissioning of Bullet camera 1/2.8" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 80m IR, 0.001Lux, 2592x1944@30fps, 2MP@60fps, 512 GB SD card slot, IP67, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal Housing. Make : Pelco/Birdeye/Axis

Supplying, installing, testing and commissioning of PVC Junction Box

Supply, Installation, Testing & Commissioning of 43" Commercial display built in Android OS

Supply ,Installation, Testing & Commissioning of Server Grade Machine with Minimum 3 Ghz Processor, 8GB RAM, 1 TB Hard disk along with necessary as required.

Supply of Surveillance Hard Disc Drive 6TB, Make Seagate/WD/Toshiba

15 Passenger elevator with 6 stops without machine room as per specification - 282 - KONE I MonoSpace R22.1-1 (a. price validity 12 months from date of signing order, b. Warranty 12 months from date of handing over)

15 Passenger elevator with 5 stops without machine room as per specification - 282 - KONE I MonoSpace R22.1 - 2 (a. price validity 12 months from date of signing order, b. Warranty 12 months from date of handing over)

SITC of 220"(16:9) Tubular Motorized screen with LVC, I.R Remote & Matte White Fiber Glass Fabric Matt White along with all supporting accessories. Make:-Grandview/Da-lite/Drapper/Suvira

SITC of Projection system with Projector & Lens :[Projection size],Aspect ratio: 16:10(WUXGA),Diagonal: 5.660 m / 222.85 in / 18.57 ft,Height: 3.000 m / 118.11 in / 9.84 ft Width: 4.800 m / 188.98 in / 15.75 ft,[Projection distance] L: 4.785–6.438 m / 188.38–253.45 in / 15.70–21.12 ft,[Optical shift range],VS1: 1.500 m / 59.06 in / 4.92 ft VS2: 0.480 m / 18.90 in / 1.57 ft,HS1: 1.344 m / 52.91 in / 4.41 ft,HS2: 0.480 m / 18.90 in / 1.57 ft,[Brightness], Projector output: 9,400 lm,Screen illuminance: 653 lx and should also comply that it is having DLP™ chip Panel size-17.0 mm (0.67 in) diagonal (16:10 aspect ratio),Display thod-DLP™ chip × 1, DLP™ system,Pixels-2,304,000 (1920 × 1200) × 1, total of 1,024,000 pixels,Lens-Powered zoom/focus lenses,Light Source-Laser Diode Laser class 1,Illumination of Life Set- Should be Vary depending on operation mode setting.20,000 hours at half luminance NORMAL /QUIET1/ QUIET2)/24,000 hours at half luminance (ECO)* Temperature: 30°C (86°F), Altitude 700m (2,297 ft),Dynamic Contrast3,Under conditions of 0.15 mg/m3 of particulate matter Lumen maintenance rate(rough estimate) : 5000 hours 80% / 10000 hours 70%,43,800 hours at constant luminance (LONG LIFE1),61,320 hours at constant ,luminance (LONG LIFE2),87,600 hours at constant luminance (LONG LIFE3). Preffered Make- Panasonic, Hitachi,Sony

SITC of Celing Mount Kit for Projector with accessories; Make Custom

SITC of 4K Transmitter HDMI bidirectional RS232 and IR over high definition base1, Make-Prefferred Make-Crestron/Lightware/Key-Digital/Kramer

SITC of High Power 2-Way Flyable Loudspeaker with 1 x 15” LF & Rotatable Horn, Coverage Pattern: 120° x 60° or better, rotatable waveguide, Frequency Response (±3 dB): 40 Hz – 18k Hz or better, Maximum SPL: 130 dB Peak or better, Sensitivity: 96 dB SPL or better, Power: 600 W or better; Should be Bi- amp/passive switchable, High Frequency Driver: 1.5" or better.

Installation accessories for mounting the above FOH arrayable speaker, i.e.eye bolt, rope wire and claimp etc as per site condition.

SITC of High Power Subwoofer 18"dual subwoofer; Frequency Range: 28 Hz –1 kHz; Power Rating :9600W Peak; Maximum SPL 30 to 500HZ =142 dB Peak; Sensitivity 30 to 500HZ =102 dB Peak; Nominal Impedance: 4 ohms; Input Modes: Drivers Parallel / Drivers Discrete

SITC of Four Channel Digital Power Amplifier, 600W@4 Ohms, On-board Digital Signal Processor and includes these integrated features: Input Router,Input Delay – Up to 1000ms,Input Parametric EQ – 8 band,Crossover , Output Parametric EQ 8 band ,Output Delay –Up to 100ms,Limiter,"Should be controllable, configurable and monitorabe through standard TCP/IQ network.";"Each output channel should be capable of providing either 70V or 100V for high impedance applications."; Completely configure the amplifier using an intuitive front-panel interface. Should have GPIO/AUX Port to Recall presets, mute channels, monitor faults, power on/off the amplifier, and more through a combined; Digital Signal Processing :96kHz, 32-bit floating point; Voltage Gain : 34dB; Frequency Response (8Ω, 20Hz - 20kHz): +/-0.25dB; THD : 0.35%; SNR: >104dB; Damping Factor : >1000; Crosstalk: >80dB; 4x600 W at 4 Ohm ,8 Ohm 70V , and 100 V

SITC of Analog Audio Mixer with 16 mono microphone channels , 4 stereo returns 4-bus architecture, with sub-group routable to mix , Built-in 24 bit digital effects processor , 32 FX settings,Tap Tempo , 3 FX parameter adjust rotaries,User FX settings store function,Direct outputs for multi-track recording individually switch-able for pre-post-fade operation,Inserts on all mono channels,Inserts on stereo mix output,Classic Soundcraft 3-band EQ with swept mid-band , Stereo 18dB/octave 100Hz high-pass filter , Dual global +48V phantom power split channels 1-8 and 9-16 , Channel Mute control , 10-segment tri-coloured metering,Two sub-group outputs , Separate mono sum output , Integral universal power supply

19" 26 U , 800mm X 600mm Equipment rack with complete fan, tray, rack rails, etc. (Approved Makes: Standard as per Direction of EIC)

SITC of Patch box with 08 connector options for mic & stage monitor

2.5 Sq. mm Speaker Cable, 100 M roll (Approved Makes: Bandridge, Klotz, Belden, Krystal)

23/0.2 mm Mic Cable, 100 M roll (Approved Makes: Bandridge, Klotz, Belden, Krystal)

Control Cable STP Cat 5e (Approved Makes : D-Link, 3C3, Belden, MX or equivalent)

Mic Stand (Approved Makes: Standard make)

Wooden Podium alongwith Cable Cubby (One HDMI Cable, Two LAN Cable, Two unswitched AC outlet,One 3.5 mm Mini Stereo Audio Jack,Compact size with square bezel Black color

fireteks Portable Fire Extinguishers as per IS 15683 (2018) High Pressure Extinguisher (Service Pressure >19 bar) Carbon Dioxide Based (as per IS 15222) Class -B fireteks Portable Fire Extinguishers as per IS 15683 (2018) High Pressure Extinguisher (Service Pressure >19 bar) Carbon Dioxide Based (as per IS 15222) Class -B

Ecofire Portable Fire Extinguishers as per IS 15683 (2018) Low Pressure Extinguisher (Service Pressure ≤19 bar) Powder Based (as per IS 4308 ) Class -A.a) Capacity 6 kg ISI Marked

PALEX 10 liter GALVANIZED MILD STEEL FIRE BUCKET (Fire suppression hand tools) PALEX (FBSTAND10LTR)

Supply & fitting of ShyamJyoti™ LED Based Solar Street Lighting System Luminary : 12W LED Luminary Luminary Housing- Weather Proof Housing Structure- Hot Deep Galvanized Module Pole : Hot Deep Galvanized MS Pole (4.5 Mtr.) Battery Box : Corrosion Resistant Painted Power Coated Metal Battery Box Other : Suitable Cable, Etc.Battery : 19.8Ah 14.8V Lithium-Ferro Battery of MNRE Approved Module : 75Wp of HBL / Gautam Solar/IEC Equivalent (Cost includes 10% CP & 5 % OHC)

KOXTANS Iron Fixed with Sleeves Pole, Height 96 inch KOXTANSR Pole Diameter - 3.5 millimeter Height adjustable - 3.5 meter Number of plate 2

Metco Green Nylon 18.3 meter Cricket Net

KOXTANS Iron Fixed with Sleeves Volleyball Pole, Height 96 inch KOXTANSR (VOLLEYBALL POLE FIXED) Pole Diameter - 3.5 millimeter Height adjustable - 3.5 meter Number of plate 2

GB INTERNATIONAL Cotton ( 9.5 meter Volleyball Net GB INTERNATIONAL (VLN 39)

baspo Transparent acrylic materia (for competition) Basketball Backstop With Installation baspo (P777) Backboard type For training Provision of adjustable mountings for minor height adjustment - Yes Thickness 25 mm Transparent acrylic material (for competition) - Length 1800 mm Width - 1050 mm

Supply, fitting, fixing, commissioning and testing of 500 kVA( level-2) , 11 or 6.6 kV/0.433 kV Deta/Star, vector group DYn11, outdoor mounting, Oil Cooled Type ONAN off circuit Star Rating Transformer with copper wound Transformer and civil foundation work along with required size & length of MS channels as per the norms 1000 kVA outdoor transformer with all accessories as per IS- 1180 of 2014, air filled cable box suitable for 11kV or 6.6 kV 2 run , 3C 120sqmm XLPE Al. armoured cable for 1.1kV, 3Run, 3.5Cx300sqmm XLPE Al. armoured cable as required. ( Make:-ABB/Voltam/ GTB/ Kirloskar / Bharat Bijlee)

Apart- from the above standard fittings followings items should be included:-

Capacity- 500 kVA(Level-2)

Installation - outdoor

No. of phase-Three

Voltage 11kV/433V

Vectro Group -DYn11

Duty- Continuous

Tapping in primary-+/- 5% to -10% in 2.5 steps

Type of Tap changer-OCTC

Cooling - ONAN

Insulation class-A

Temp. rise @ 50 Deg. C. Ambient

Oil by Thermo Meter :- 50 Degree C.

In winding by Resistance :- 55 Degree C.

MAIN LT PANEL

Main LT Panel: Supplying, designing, manufacturing, installation, testing, fitting, fixing and commissioning in correct alignment position, effecting proper connection of all incomers and outgoing of LT panel of 14 SWG CRCA Sheet (2mm) steil IP-54 floor mounting cubical type LT Panel suitable for operation on 415V, 50Hz, 3Ph, AC supply and fault level 50kA. Apporexmate size (Shall be given at the time of work order ) with front operated construction including seperate fabrication arrangement for fixing of switchgears and meters.

The sheet steel under go minimum seven tanks treatement followed by finishing poder coating of minimum 60 microns thickness duly compart mentalized with locking arrangement duly fixed on base channel of suitable size having accessories mounted inside cubicale panel, earthing with 2 Nos. of earth studs.

All opening shall be covered by soft rubber gaskit,enclosure shall be galvanished. Panel shall have suitable cable entry from top and bottom and suitable arrangement for multiruns aluminium cables for MCCB.

The Panel includes 415V, 1000A , 3 ph, 50kA , 50Hz Electrolytic aluminium bus bar( E91EWP) , earth bus with removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. All inter connections shall be made with 4, 6, 10,16 sq. mm PVC cu wire.

The above panel consting of the following:

a)All out going MCCB as per specification.

b) All breaker handlings truck shall be provided by the supplier

Bill of Materials

ACB -MDO type direct action with OL, EF, SC and over and under current protection with microprocessor release. Make-Schneider MW master pack/ Legrand DMX3/ L& T (U-power)/ Siemens-3wl(german)/ ABB

MCCB- with OL, EF, SC and over and under current protection with thermal magnetic release.

INCOMERS:-

3 nos-800A FP ACB MDO type with handle(50kA) for transformer incomer- 2 nos and 1 no for interlocking arrangement

OUTGOINGS:-

2 nos-250A , FP MCCB(35kA)

2 nos-125A , FP MCCB(35kA)

7 nos-100A , FP MCCB(35kA)

2 nos-63A , FP MCCB(16kA)

Analogue type voltmeter - 3 nos , Make :- AUE / Universal / L&T / Esma.- 2 nos

Analogue type Ammetesr . Make :- AUE / Universal / L&T / Esma.- 3 nos

CT 500/5VA -5 class one Epoxy resin cast CT 3 Set. Make :- Kappa / Matrix / SG Electricals / EPICAST.- 3 nos

Table 900W x 450D, 18mm thick PLPB top, 40x40x1.2mm CRCA powder coated frame. Table Top 18 mm Thick PLPB Board as Per Approved Laminate Shade. Understructure Made Of Prime Quality CRCA 40 x 40 x 1.2mm Square Metal Pipe. Table Top Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Understructure CRCA Metal Pipe 25X25mm With 1.2mm Thick Four Side Welded With Vertically Metal Pipe. Table Understructure 850W X 550D In 25 X 25 Square Pipe With 1.2mm Thick. Height Of The Understructure 700mm. Legs Of The Table Hard Rubber Shoes. All Metal Shall Be Powder Coated After Being Treated With at Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Metal Storage ( 1D + 1S ) Made Of Prime Quality 22guage CRCA Metal Sheet Tank Treatment With Minimum 45 - 50 Micron Powder Coating. Legs Of The Table Hard Rubber Shoes. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Non-Revolving and Non Tilting chair with Armrest-Metal Chrome frame, Leatherete seat & back. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

4 seater Conference Table Top 25mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade. Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board. Modesty Panel Prime Quality 18mm Thick 600 mm High PLPB Board Supported To Top. 7 mm High Pvc Bofurs Screw With Gable - end.Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Conference Table Top Round Type Corner With Between Part Hollow Section. Conference Table Top Divided Into Various Parts Top Joints With Gable - End Minifix & Dowels . All Table Top , Gable & Modesty Panel Fix Joints With Minifix Dowels & Other Fittings Equipment . All Wooden Panels Cleaning Corner & Round Corner Knitted Finish. Four Gable - End Round Side Taper Fix To Top . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

4 Seater Restaurant Table-Table Top 25mm Thick MDF+Membrane Top as per Approved Shade. Over All Size Of Table 1200W x 600D x 750H . Understructure Made Of Prime Quality CRCA 40 x 40 mm Square Metal Pipe Duly Powder Coated. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used. All Metal Shall Be Coated. After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (60 – 80) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Methodex Restaurant / Cafeteria Chair -Round Seat Cafe Chair Overall Size 440W x 430D x 785H . Base Seat Plywood Made Of 12mm Hot Pressed Supported . Understructure Base Of Chair Round SS Pipe Structure Fixed Type . Understructure Base Fixed Type CRCA 25mm Dia SS Round Pipe 1.2mm Thick . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Base Frame . Chair Max Height 785 & Depth 430mm . 400 Dia Base Seat 12mm Thick Ply & 440W x 345H Back 25mm SS Round Pipe 1.2mm Thick . Height From Seat To Ground 455mm . All SS Round Tube Pieces Shall Be Welded Properly Strongly and conformity with regulations . Legs Of The Chair Hard Rubber Shoes . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

3 Seater Public Place Seating Chair of mild steel with arm and backrest WITHOUT CUSHION-Long Chair Made Of Good Quality Products Of MSPL Standard Models . 407W x 405D Base Seat 1.2mm Thick Perforated MS Sheet Duly Powder Black Coated . 410W x 205D Back Seat 0.8mm Thick Perforated MS Sheet Black Powder Coated . Base Frame Made Of 78 x 38 x 1.2mm Thick Rectangular Metal Pipe Duly Powder Coated . Chair Height Floor From Top 860 . Understructure Of Legs 50mm Dia Round Metal Pipe With 1.6mm Thick Powder Coated . Hand Rest Moulded With 32 x 15mm Oval Shape Metal Pipe 1.2mm Thick Powder Coated . Mounting Plate Chair Ms Sheet 2mm Thick . Mounting Brackets Chair Ms Sheet 5mm Thick . Supported Bush Handles Ms Bright Bar 12mm Dia . Understructure Of Chair Frame Made Of 19mm Dia Round Metal Pipe 1.2mm Thick Powder Coated . Handle Inner 460mm . Ends Of Base & Other Metal Pipe PVC Caps . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . Thickness Of Coating (40 – 50) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Non-Revolving and Non-Tilting chair withArmrest-1)SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed ply and should be true resistant tant commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) 2)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. 3)UNDERSTRUCTURE ASSEMBLY: The assembly should be a mainframe made of 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube and a welded leg tube made of dia. 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube to the form the complete assembly which should be black powder coated (DFT 40-60 microns).

Sofa Sets, Number of seats 3+2-Sofa 3 seater Made Of Good Quality Products Of MSPL Standard Models . 12mm Ply Used Made Of Back & Base . Upholstery Made Of Prime Quality Rexine Black . Base Seat Moulded With Foam , ( 90mm + 21mm ) Thick , D 28KG/m3 . Back Seat Moulded With Foam , 45 Thick , D - 28KG/m3 . Arm rest Moulded With Foam , 45 Thick , D - 28KG/m3 . Back Inserted Foam , 21 Thick , D - 28KG/m3 . Ends Of The BJ 3S Sofa Structure PVC Caps . Sofa L Brakets & Base Frame Made Of Prime Quality MS . Fastners Nut Bolt 4Nos . Size M8 x 38mm . Sofa Structure Shall have MS Spring Base . Understructure Made of Base Frame 20 x 20 Square SS Pipe 1.2mm Thick . Support Frame Made Of 12mm Dia Round SS Pipe 1.2mm Thick . Side Frame Made Of 25mm Dia Round SS Pipe 1.6mm Thick . Pinewood 25W x 25mm Thick . Seat Height From Bottom To Base 458mm . Back Height From Base Seat To Top 356mm . Hand Rest Width 150mm . All SS Pipes Shall Be Welded Properly Strongly and conformity with regulations . Sofa Structure Stailness Steel Pipe Shall Be Abrasive Polished External Finished . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.2 seater Sofa Made Of Good Quality Products Of MSPL Standard Models . 12mm Ply Used Made Of Back & Base . Upholstery Made Of Prime Quality Rexine Black . Base Seat Moulded With Foam , ( 90mm + 21mm ) Thick , D - 28KG/m3 . Back Seat Moulded With Foam , 45 Thick , D - 28KG/m3 . Arm rest Moulded With Foam , 45 Thick , D - 28KG/m3 . Back Inserted Foam , 21 Thick , D - 28KG/m3 . Ends Of The BJ 3S Sofa Structure PVC Caps . Sofa L Brakets & Base Frame Made Of Prime Quality MS . Fastners Nut Bolt 4Nos . Size M8 x 38mm . Sofa Structure Shall have MS Spring Base . Understructure Made of Base Frame 20 x 20 Square SS Pipe 1.2mm Thick . Support Frame Made Of 12mm Dia Round SS Pipe 1.2mm Thick . Side Frame Made Of 25mm Dia Round SS Pipe 1.6mm Thick . Pinewood 25W x 25mm Thick . Seat Height From Bottom To Base 458mm . Back Height From Base Seat To Top 356mm . Hand Rest Width 150mm . All SS Pipes Shall Be Welded Properly Strongly and conformity with regulations . Sofa Structure Stailness Steel Pipe Shall Be Abrasive Polished External Finished . The product should bear IGBC Green Pro certificate for product categFory. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Restaurant / Cafeter table -Table Top 25mm Thick MDF+Membrane Top as per Approved Shade. Over All Size Of Table 1200W x 600D x 750H . Understructure Made Of Prime Quality CRCA 40 x 40 mm Square Metal Pipe Duly Powder Coated. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used. All Metal Shall Be Coated. After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process. Thickness Of Coating (60 – 80) Micron. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Plastic Moulded Chair With Arms With Cushion Single Piece Plastic Moulded

METHODEX -6 Seater Restaurant Table

Specification:- Centre Table MS TRUMPON 3921, Made up of engineering wood. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) forGUEST HOUSE FURNITURE range for ergonomic design.

Computer Table consists of Computer table with key board -Computer Table Top 18mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade. Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board. Top Size 800W X 450D. 18mm Thick PLPB Wooden Shelve Fix In Table under Table Top . Right Hand Side Provided L Shape Shelve Use For CPU & UPS . Shelve Used Sliding Telescopic Channel With All Fittings. Table , Shelve & Sides Panels Flat Edge Duly Sealed With Pvc Beading . 50mm High Wooden Panel Skirting Provided in Computer Table . 7mm High Pvc Bofurs Screw With Gable . All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment . Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Newspaper Reading Stand - NEWS PAPER STAND - 900W x 600D x 1100H News Paper Stand Made out of 25 mm x 25mm CRCA pipe U/S with Hut Style Design For Keeping Daily News Paper and steel strips are Provided for locking News Paper Height Of Stand is 1100 mm ( can be Done As Per Requirement). Base pipe used from 50 x 25 mm. All Steel Parts Are Duly Powder Coated With 40 to 50 Microns.This Versatile Newspaper Reading rack is Meant For Two News Papers One on Each Side And Two Persons Can Read The Newspaper At Convenient Standing Height . All Frames Square Pipe Closed With Pvc Caps . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for EDUCATIONAL FURNITURE range for ergonomic design.

METHODEX POWDER COATED MS 6SEATER RESTURENT TABLE-Table Top Designed With 25 mm PLPB . Top Size 1800W x 900D. Understructure Leg Designed With combination of 50x50 and 40X40mm Square CRCA 16 Guage Thick Duly powder Coated . Legs Of The Table Hard Rubber Shoes. Wooden Panels Prime Quality Board With ISI Marked . MIG Welding All - Around The Weld Joints Using Inert Gas (Argon.) The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Almirah Steel shelving cabinets-Overall Size 915W x 485D x 1980H . Office Almirah Made Of Prime Quality CRCA Ms Sheet Panels 0.8mm Thick Powder Coated Finish With Approved Shade . Each Shelve Made Of 0.8mm CRCA MS Sheet Powder Coated . Each Shelve Shall Be Formed Such The Edges Are Bend Two Times At Right Angle. Front Shutter 1mm Thick CRCA Ms Sheet Powder Coated Riveted With Hinges. . No Sharp Edges Of Almirah Ends . All Shelve Rack Divided Into Equal Parts . Leg Shall Be 125 x 90 X 452MM 2 Nos With 1mm Thick CRCA Metal Sheet Powder Coated . Door Die Cast Chrome Plated Handles Fitted With Washer & Double Nut . Handles Ring Made Of PVC Cap . Locking Bright Bar 10mm Dia . Almirah All Metallic Panels Screw With Nut & Bolt . Bottom Shelve 125mm High Up To Ground . All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations . CO2 Welding Shall Be Used . All Metal Shall Be Coated After Being Treated With At Least Three Stages And Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating almFor Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for STORAG FURNITURE range for ergonomic design.

Stainless SteelRectangular Dining Table with C3431E Rectangular fixed Chair-Dinning Table consists of Dinning Top is made up of and 1 mm thickness Stainless steel sheet of SS 304 Grade with overall dimension of 1800(L) X 760(D) X 750(H). The table top is rainforced with a 18mm PLP Board. Dinning top sheet shall be extended to the sides for a depth of 24 mm in all directions including, edge rounding, grining and finishing,etc all complete. The Table top shall finish in such a manner to avoid any sharp edges. Stool Seats are made of 300 mm dia SS 202 Grade formed Plates of 1 mm thickness welded over 3 mm thick MS Plate. Supporting understrucure of table consists of 3 nuber C legged frame made up of 40 x40 x1.6 mm ERW tube and are connected to 4 numbershorizontal members of MS ERW tube 40 x 40 x 1.6 mm. The supporting vertical member of each stool seat consists of MS ERW tube 40 x 40 x 1.6 mmn and is connected to C legged frame of table top. All Metal components of entire assebmly confirm to IS 4923. Both the horizontal and vertical pipes are welded together by MIG welding confirming to IS standard IS 816:1969 and is tested for welding confirming to IS 822:1970. All CRCA Componets shall be finishded with epoxy polyster powder coated DFT 50-60 Micron confirming IS 13871:1993. Understructure height will be 725mm from the ground, and the stool height will be 500mm from the ground.. Supply and installation of In

Unbranded Stainless Steel Rectangular Dining Table with C3431E Rectangular fixed Chair-Dinning Table consists of Dinning Top is made up of and 1 mm thickness Stainless steel sheet of SS 304 Grade with overall dimension of 1800(L) X 760(D) X 750(H). The table top is rainforced with a 18mm PLP Board. Dinning top sheet shall be extended to the sides for a depth of 24 mm in all directions including, edge rounding, grining and finishing,etc all complete. The Table top shall finish in such a manner to avoid any sharp edges. Stool Seats are made of 300 mm dia SS 202 Grade formed Plates of 1 mm thickness welded over 3 mm thick MS Plate. Supporting understrucure of table consists of 3 nuber C legged frame made up of 40 x40 x1.6 mm ERW tube and are connected to 4 numbers horizontal members of MS ERW tube 40 x 40 x 1.6 mm. The supporting vertical member of each stool seat consists of MS ERW tube 40 x 40 x 1.6 mmn and is connected to C legged frame of table top. All Metal components of entire assebmly confirm to IS 4923. Both the horizontal and vertical pipes are welded together by MIG welding confirming to IS standard IS 816:1969 and is tested for welding confirming to IS 822:1970. All CRCA Componets shall be finishded with epoxy polyster powder coated DFT 50-60 Micron confirming IS 13871:1993. Understructure height will be 725mm from the ground, and the stool height will be 500mm from the ground.. Supply and installation of In

Metal Beds (Without Mattress) With Frame of MS frame-Bed Overall Size : 2005 mm Lx 950mm W X 650mmH1X400mmH2, Headrest of size 280mm Made in 1mm Sheet and footside sheet panel made in 1mm also provided as per attached image : 12-14mm MR grade Ply will be used for mattress. Bed leg framein 50x25x1.2 mm and Mattress panel will be supported on minimum 3 supports combination of size 25x25x1.2mm & 20x20x1.2mm pipes : Mattress panel height should be 400mm . Complete structure should be duly powder coated

PVC Moulded Chair

Teak Wood 6 Seater Restaurant Table- Table Top Designed With 25 mm PLPB . Top Size 1800W x 900D. Understructure Leg Designed With combination of 50x50 and 40X40mm Square CRCA 16 Guage Thick Duly powder Coated . Legs Of The Table Hard Rubber Shoes. Wooden Panels Prime Quality Board With ISI Marked . MIG Welding All - Around The Weld Joints Using Inert Gas (Argon.) The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Diinning table 6 seater - Dinning Table consists of Dinning Top is made up of and 1 mm thickness Stainless steel sheet of SS 304 Grade with overall dimension of 1800(L) X 760(D) X 750(H). The table top is rainforced with a 18mm PLP Board. Dinning top sheet shall be extended to the sides for a depth of 24 mm in all directions including, edge rounding, grining and finishing,etc all complete. The Table top shall finish in such a manner to avoid any sharp edges. Stool Seats are made of 300 mm dia SS 202 Grade formed Plates of 1 mm thickness welded over 3 mm thick MS Plate. Supporting understrucure of table consists of 3 nuber C legged frame made up of 40 x40 x1.6 mm ERW tube and are connected to 4 numbers horizontal members of MS ERW tube 40 x 40 x 1.6 mm. The supporting vertical member of each stool seat consists of MS ERW tube 40 x 40 x 1.6 mmn and is connected to C legged frame of table top. All Metal components of entire assebmly confirm to IS 4923. Both the horizontal and vertical pipes are welded together by MIG welding confirming to IS standard IS 816:1969 and is tested for welding confirming to IS 822:1970. All CRCA Componets shall be finishded with epoxy polyster powder coated DFT 50-60 Micron confirming IS 13871:1993. Understructure height will be 725mm from the ground, and the stool height will be 500mm from the ground.. Supply and installation of In

DNR SYSTEMS MODULAR TABLE L X D & H 1500 millimeter X 900 millimeter 750 millimeter

Revolving Chair -High Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat & Back Plywood Made Of 15mm Hot Pressed Supported . Upholstery Structure Moulded With Prime Quality Leatherite . PHA ( Gas- Lift ) 85mm (TDC 152mm & BDC 67) . Understructure Base Revolving Pedestal Chorme Plated Steel Base With PP Hub Cap . Machanism Tilt Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 1250 & min Depth 730 . 500 x 490 Base Seat100mm Thick Moulded With PU Foam , D -45 kg/m3 , H- 18 & 520W x 690H Back Seat 100mm Thick Moulded With PU Foam , D -45 kg/m3 , H-18 . 470/580 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest Height From Seat 200mm . Arm Rest PU Moulded . Height From Seat To Ground 500mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 720mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Wooden Almirah, Height 2100

Unbranded Portrait/ Landscape Not applicable Fabric Pin Up Notice Boards 4x 3

Wooden Podium design Gable end and modesty panel and top material Teak wood- Top Designed With 18 mm Thick Commercial Board Affixed With 0.6mm Mica . Support Structure Of Podium Designed With Solid Wood . Modesty Panel Having Affixed With Veneer Pressed With Polish . Modesty Panel Design With Solid Wood And Beading . All Edge And Structure Finished With Proper Color Combination Matched To Laminated Shade. Front & Side Designed By 25mm Commercial Board With 3mm Shisham Vineer Duly Wallnut Polish Finish . Table Made By Joint Of Two Wooden Parts . Legs Of The Podium Hard Rubber Shoes. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

THREE SEATER TUBULAR STEEL SOFA SET- BJ Made Of Good Quality Products Of MSPL Standard Models . 12mm Ply Used Made Of Back & Base . Upholstery Made Of Prime Quality Rexine Black . Base Seat Moulded With Foam , ( 90mm + 21mm ) Thick , D 28KG/m3 . Back Seat Moulded With Foam , 45 Thick , D - 28KG/m3 . Arm rest Moulded With Foam , 45 Thick , D - 28KG/m3 . Back Inserted Foam , 21 Thick , D - 28KG/m3 . Ends Of The BJ 3S Sofa Structure PVC Caps . Sofa L Brakets & Base Frame Made Of Prime Quality MS . Fastners Nut Bolt 4Nos . Size M8 x 38mm . BJ Sofa Structure Shall have MS Spring Base . Understructure Made of Base Frame 20 x 20 Square SS Pipe 1.2mm Thick . Support Frame Made Of 12mm Dia Round SS Pipe 1.2mm Thick . Side Frame Made Of 25mm Dia Round SS Pipe 1.6mm Thick . Pinewood 25W x 25mm Thick . Seat Height From Bottom To Base 458mm . Back Height From Base Seat To Top 356mm . Seat 585 Depth . Hand Rest Width 150mm . All SS Pipes Shall Be Welded Properly Strongly and conformity with regulations . BJ Sofa Structure Stailness Steel Pipe Shall Be Abrasive Polished External Finished . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

STEEL CHAIR -steel chair with steel frame , seat

Revolving Chair With Arm Centre pivot mechanism-Medium Back Chair Made Of Good Quality Products Of MSPL Standard Models . Seat Plywood Made Of 12mm Hot Pressed Supported Back Inner PP Structure . Upholstery PVC Structure Moulded With Prime Quality High Stretch Fabric . PHA ( Gas-Lift ) 105mm ( TDC 171mm & BDC 66 ) . Understructure Base Revolving Pedestal Steel Inserted PP Base With PP Hub Cap . Machanism Torsion Bar Adjustment Can Be Operated In Seating Position . Seat & Back Are Firmly Connected To The Base Frame Machanism . Machanism Provided Upright Position Locking . Chair Max Height 980 & min Depth 715 . 470W x 430D Base Seat 70mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 & 430W x 470H Back Seat 50mm Thick Moulded With PU Foam , D - 42 kg/m3 , H - 20 . Base Seat Shell ABS Cover At Underside . Back Seat Shell ABS Cover At Back Side . L - Patta Mild Steel . Beading Finish NA . 440/540 Arm Rest Fitted To The Seat With Armrest Connecting Brackets . Arm Rest PP . Arm Rest Height From Seat 170mm . Height From Seat To Ground 440mm . Seating Height Can Be Adjusted With a Pneumatic Gas Lift . Pedestal Pitch Centre Dia 715mm With Casters . Casters Made Of Moulded Black Nylon Metal Bolt Inserted & Fitted With 5 Nos . Twin Wheel Casters 50mm Dia . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

RADIANCE - 01 CAFE TABLE SIZE - 1800W x 1200D x 715H Table Top 25mm Thick PLPB Board With 2mm Pvc Edgebanded Finish With As Per Approved Laminate Shade. Seat 18mm Thick PLPB Board With 0.8mm Thick Pvc Edgebanded. Understructure Made Of Prime Quality CRCA 25mm Dia Round Metal Pipe Duly Powder Coated . Table Top Base Seat Height From Ground 450 mm . Understructure CRCA Round Metal Pipe 25mm Dia With 1.2mm Thick All Side Welded With Vertically Metal Pipe & 7 tank treatment with minimum 45-50 micron powder coating .All Frames Round Metal Pipe Closed With Pvc Caps. Legs Of The Table Hard Rubber Shoes. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be Coated After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust, And Other Dirt Using Special Thermal Control Coating For Metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m² . Automatic Spray Coating Shall Be Applied To Be Followed By a Drying Process In a Thermal Furnace With Suitable Temperature And Time For The Process . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Coomon Room Chair - Cafe Chair Overall Size 480W x 490D x 780H . . Base Seat & Back Made Of Moulded PP Structure Supported ( Single Piece Moulded Seat & Back Shell ) . Understructure Base Of Chair Round SS Pipe Structure Fixed Type . Understructure Base Fixed Type 19mm Dia SS Round Pipe 1.2mm Thick . Machanism & PHA ( Gas Lift ) NA . Seat & Back Are Firmly Connected To The Base Frame . Chair Max Height 780 & Depth 490mm . 440W x 410D Base Seat Moulded With PP Structure & 440W x 390H Back Seat Moulded With PP Structure . Height From Seat To Ground 420mm . All SS Round Tube Pieces Shall Be Welded Properly Strongly and conformity with regulations . Legs Of The Chair Hard Rubber Shoes . Assembly Shell Affixed On MS Frame With Help Of Screw . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for CAFE FURNITURE range for ergonomic design.

Executive Computer Table CUM LIBRARY -LIBRARY TABLE SIZE - 1200W x 900D x 770H Table Top 25mm Thick PLPB Board as Per Approved Laminate Shade. Total Height Of The Library Table 770mm. Metal Structure Width 1150mm & 850mm Depth. Understructure Made Of Prime Quality CRCA 25x25mm Square Metal Pipe. Perforated Modesty Panel 0.8mm Thick CRCA Metal Sheet with 25 mm square pipe boundry. Upper Wooden Panels 18mm Thick PLPB Board Used For Book Shelve. Table Top & Upper Wooden Panels Flat Edge Duly Sealed With 2mm Thick Pvc Beading. Upper Wooden partition/storage size : 300 mm H x 300 mm D. Understructure CRCA Metal Pipe 25X25mm With 1.2mm Thick Four Side Welded With Vertically Metal Pipe. All Metal Pieces Shall Be Welded Properly Strongly and conformity with regulations. CO2 Welding Shall Be Used. All Metal Shall Be Powder Coated After Being Treated With At Least Three Stages Cleaned From Oil,Grease, Dust. Coating For metal Furniture To Form a Layer Of Base Coating Of (iron phosphating) (0.4 – 0.8) gm/m². Coating thickness must be between 60 to 80µ. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for EDUCATIONAL FURNITURE range for ergonomic design.

Unbranded Plastic Moulded Chair With Arms With Cushion Single Piece Plastic Moulded

Executive Table with Both side pedestal unit

Wooden Book Case made up of Flat single layer MDF board of grade SBG II of IS 12406/Latest and 2 shelves

Computer Table consists of Computer table with key board-Computer Table Top 18mm Thick PLPB Board With 2mm Thick Pvc Edgebanded Finish With As Per Approved Laminate Shade. Top Supported Understructure Of Table Gable - End Made Of Prime Quality 18mm Thick PLPB Board. Top Size 800W X 450D. 18mm Thick PLPB Wooden Shelve Fix In Table under Table Top . Right Hand Side Provided L Shape Shelve Use For CPU & UPS . Shelve Used Sliding Telescopic Channel With All Fittings. Table , Shelve & Sides Panels Flat Edge Duly Sealed With Pvc Beading . 50mm High Wooden Panel Skirting Provided in Computer Table . 7mm High Pvc Bofurs Screw With Gable . All Wooden Panels , Gables & Modesty Fix Joints With Minifix Dowels & Other Fitting Equipment . Wooden Panels Cleaning Corner Knitted Finish . All Wooden Panels Prime Quality Board With ISI Marked . The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.

Unbranded Portrait/ Landscape Not applicable Fabric Pin Up Notice Boards 4x3

DUAL DESK SIZE:(L)1050MM X (W)914MM X (H)750MM STUDEN DESK *MODERN DESIGN * MADE FROM HEIGH QUALITY WOOD MATERIALS * LONG LIFE & HIGHLY DURABLE MODEL NO: OLWEN

READING CHAIR MODEL-1)SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed ply and should be true resistant tant commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D) 2)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for25%compression. 3)UNDERSTRUCTURE ASSEMBLY: The assembly should be a mainframe made of 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube and a welded leg tube made of dia. 0 1.95 ±0.03cm. x 0.16 ±0.016cm.thk. M.S. E.R.W. tube to the form the complete assembly which should be black powder coated (DFT 40-60 microns).

Modular Work Stations with Four Seater Plus Shape Cluster WORKSTATIONS 1500/1500X600MM (DB WS02) CLUSTER OF 4 PLUS SHAPE with Curvilenear Top-Top to be made up of ISI mark 25 mm thick pre laminated Particle Board finished with 2 mm thick PVC edging applied on Through Feed Edging Machine UNDERSTRUCTURE- The under structure to be made up of CRCA, C shaped legs shall be of pipe of size 50x50 mm and 40x40 cross member for support and stability finished with powder coating. SCREEN- Divider screen of size1500x300mm to be fixed above the table top level. The fabric screen to be in 30/32mm thickness having aluminium sections all 4 sides. Race way CRCA raceway for carrying electrical and data wiring are provided below the table top with provision for fixing switches. Each cluster to be provided with wire riser from floor to wire raceway and aluminium access flap on worktop for easy access to electrical switches . PEDESTAL, KEY BOARD AND CPU TROLLEY ARE NOT CONSIDERED IF REQUIRE COST WILL BE EXTRA. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for LAB FURNITURE range for ergonomic design.

LED indicator (RYB) of 220V. 1 Set of 3 nos Make :- ESSEN / L&T - ESBEE / Binay / Teknik- 9 nos

Fuse base with HRC Fuse Set of 3 nos. Make :- Legrand / L&T / Schinder. - 9 nos

Outdoor Feeder Panel ( for street light and High mast): Supplying, designing,manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of suitable size ,earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. All inter connections shall be made with 2.5, 4 , 6 Sq mm PVC Cu. wire. The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs

Incomer : 1 No. 100A/FP/16kA/ MCCB thermomagnetic release type, and S/C, O/L protection, with Rotary Handle & Spreader links.

Outgoings: MCB 40 A, TPN, 10kA - 6 nos. for highmast, street lights & bollard lights

40 amp 4P Duty contactor

0-24hrs Timer switch with bypass arrangement

100 amp 415 V heavy duty three phase with neutral busbar chamber

Add GST 18 %

Add Labour cess 1%

MKP INFRA VENTURES (BID ID -640898)