SPECIAL REPAIR TO BLDG NO. P-16 (ADM BLOCK) AT DINJAN MIL STATION AND CERTAIN MINOR WORKS UNDER GE DINJAN.

Amount

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for plain cement concrete (1:4:8) type C-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete, etc complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in coping etc complete all as specified and as directed.

M&L for RCC (nominal mix ) type B1 1:2:4 (20 mm graded aggregate) in foundations, including rafts, footings, foundation beams ; plinth beams; bases for columns, etc ; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC (nominal mix ) type B1 1:2:4 (20 mm graded aggregate) in Beams, cantilevers, bressummer, lintels over 1.5 span complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 (nominal mix) , type B-1 (Using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed. (Note : reinforcement shall be measured and paid separately against respective item).

M&L for RCC (nominal mix ) type B1 1:2:4 (20 mm graded aggregate) in columns, pillars, piers, post and struts etc complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia and over ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

M&L for mild steel TMT bars 6 to 8mm dia and over ,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Use and waste of form work to flat sides of cocnrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams ; and similar work ; vertical or to batter complete all as specified and directed.

Use and waste form work to flat sides of soffits of floor or roof beams, beam hauching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc also splays between floors and beam, etc complete all as specified and directed.

Use and waste form work to flat sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

S&F form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in Cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Taking down the chowkhats or frames not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed

Taking down the chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frames) complete all as specified and as directed

S&F pressed steel frames for doors local work shop made of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F pressed steel frames for doors local work shop made of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitered and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as in SSR Part I Section 8 clause 8.24 (b) complete all as specified and as directed..

S&F 35 mm thick, second class hardwood, plain, framed, panelled shutters (any number of panels), with lock rail and panels of 9mm BWR commercial Ply or 12mm thick veneered particle board medium density, with commercial face veneering on both faces. the size of rail and styles 150 & 100mm, kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, complete all as specified and as directed by Engr-in-Charge.

S&F for 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F 150 mm long, aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 150mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F for 300 mm long, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections etc complete all as specified and as directed.

S&F 375mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F in repair steel windows with side hung shutters including projecting/box type hinges with steel handle, and steel peg stay complete with glazing bars, devotailed or welded complete all as specified and as directed.

S&F in repair steel windows with side hung shutters including projecting /box type hinges with steel handles and steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F for galvanised mild steel wire cloth of 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F for 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) for embedding hold fast, bed block, cills, etc including necessary form work complete all as specified and as directed.

M&L for hardcore of broken stone aggregate of guage n.exc 63mm , deposited, spread and levelled in layers n exc. 15 cm thick, consolidated, watered and rolled/rammed to a true surface complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F for Joist, channel, angle, or tee sections of Fe 290 (Gde E-165) fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and as directed.

M&L for Mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidating complete all as specified and directed.

M&L for salt glazed stone ware drain pipes 150 mm bore, grade 'A' laid in trenches, jointed and tested complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggragate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore SGSW/RCC drain pipes complete all as specified and as directed .

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and as directed.

S&F 0.63mm thick, Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275complete all as specified and as directed.

S&F for 0.80mm thick, mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S&F for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 10cm long complete all specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar in (1:6) for laying floor finishes complete all as specified and as directed

M&L for coloured glazed ceramic tiles in vertical surface of size 450X 350X 7 mm thick over 10 mm thick back coat of cement mortar in (1:4) set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over 10 mm thick back coat of cement mortar in 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite including 25mm thick screed bed in CM 1:6.all as specified and as directed.

M&L for 75 mm thick plain cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of floor, etc complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 40 mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) in sub base finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement mortar (1:4) using water proofing compound in top layer (water proofing compound measured as separately) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick of internal wall on fair faces of brick work or concrete surfaces in cement mortar in (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick on ceiling in cement mortar (1:3) finished even & smooth without using extra cement complete all as specified and directed

Supply only Liquid water proofing compound complete all as specified and directed.

S&F for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. Note: Glass will be measured separately.

M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a) Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. (b) M&L 25 thick cement concrete type B0 1:2:4( 12.5 mm graded aggregate) finished even and smooth. (c) M&L for 15 mm thick cement mortar in 1:4 finished even and smooth. (d) Preparing & cleaning of fully dried cement plastered surface. (e) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 litres per sqm conforming IS-3384. (f) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (g) One coat of aluminium paint over APP membrane @0.11Kg/Sqm. Note:- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab.

M&L for preparation of new plastered surface of walls etc and applying three coats of white wash on walls complete all as specified and directed

M&L for preparation of new plastered surface etc and applying three coats of white wash on ceiling complete all as specified and directed

M&L for preparing old plastered or unplastered surfaces of walls by washing, rubbing down and scraping of existing distempering/painted surfaces etc and applying one coat of distemper oil emulsion complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of walls by brooming down or steel wire brushing, scraping down with steel scraper, smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of ceilings by brooming down or steel wire brushing, scraping down with steel scraper, smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and as directed.

M&L for preparation of new or previously untreated wooden surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed

Supply, laying, connection and testing, 15mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply, laying, connection and testing, 20mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Supply and laying, CPVC pipe of 16mm outer dia, SDR 11 pain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Supply and laying, CPVC pipe of 20mm outer dia, SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed.

Refixing old 15mm bore, steel tubes, and cnnection in new or old position complete to wall and ceiling or laid in floors etc complete all as specified and as directed.

Refixing old 20mm bore, steel tubes, and cnnection in new or old position complete to wall and ceiling or laid in floors etc complete all as specified and as directed.

Dismantling of water tank capacity excedding 250 Ltrs and not exceeding 500 Ltrs and removing to store complete all as specified and as directed.

Dismantling of water tank capacity exceeding 500 Ltrs and not exceeding 1000 Ltrs and removing to store complete all as specified and as directed.

S&F for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for 20 mm bore, ball brass valves, high pressure, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F for 20 mm bore, gun metal, globe or gate valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe providing 110mm PVC WC connector etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white, with seat white close pattern with flat bottom and cover mild steel chromium plated or aluminium hinging device incl flush pipe and joint etc and connection to drain, flushing pipe, anti- syphonage pipe, and fixing arrangements with fixing bolts etc including making good to disturbed surfaces of floor by filling with PCC (1:2:4) type B-0 to match with the existings complete all as specified and as directed.

S&F in repair PVC low level flushing cistern, 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC conection pipe and flush pipe of polyethylene of low or high density or PVC 32 mm dia, complete all as specified and directed

S&F for 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F for brass chromium plated shower rose, 125 mm size, with or without swivel joint any size incl fixing to steel pipe or union complete all as specified and as directed

S&F in repairs vitreous china wash hand basin white flat back size 550x400mm excluding taps, waste chain and plug and porcelain stopper including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and as directed.

S&F in repairs for vitreous china bowl urinal, flat back size of 465x355x265mm whitw with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) but fixing plug bedding urinal against wall in cement mortar (1:2) securing urinal to plug including 60mm long brass screws pointing around urinal back in cement mortar including 15mm brass stop cock and waste coupling brass CP complete all as specified and as directed.

M&L for PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement including disconnection of old existing trap, and connected with existing water pipe complete all as specified and directed.

S&F in repair 32mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed

S&F for tubular towel rail, 20mm dia, D type, 60cm long Brass Chromium plated between flanges complete all as specified and as directed

S&F in repair pillar taps of size 15mm, chromium plated fancy type cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S&F in repairs for bib taps fancy type CP with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule and fixed of size 15mm bore in repair complete all as specified and as directed.

S&F in repairs 15mm stop valves (concealed type), cast copper alloy fancy type chromium plated, long sunk and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F for 16mm outer dia, CPVC brass thread elbow complete all as specified and as directed.

S&F for 20mm outer dia, CPVC brass thread elbow complete all as specified and as directed.

S&F for 16mm outer dia, CPVC brass thread Tee complete all as specified and as directed.

S&F for 20mm outer dia, CPVC brass thread Tee complete all as specified and as directed.

S&F for 16mm outer dia, CPVC brass thread union complete all as specified and as directed.

S&F for 20mm outer dia, CPVC brass thread union complete all as specified and as directed.

S&F in repairs110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) junction double, (double T), equal or unequal complete all as specified and as directed.

S&F for 125/110 mm bore PVC (SWR) gully trap complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) vent cowl complete all as specified and as directed.

S&F for 100mm dia Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

S&F for 75mm dia Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

Taking down carefully point wiring for one light, socket or power etc incl all fittings such as switches sockets, holders, light fittings, fan requlators etc and making good the disturbed surface of wall, ceiling etc including seperating serviceabel light fittings, switches etc and keeping in safe custody for reuse and removal of unserviceable materials from site complete all as specified and directed.

M&L for concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size passing through and including suitable PVC conduit with all fittings and accessories of PVC conduit (like Tee, bend etc.) complete fixed to walls /ceiling etc , including cutting chases, making good with cement mortar 1:3, terminated in and including providing PVC/modular metal box of suitable size with 3mm thick hylam sheet cover for fixing of switches, sockets, fan regulators etc for one light/fan/bell/buzzer point controlled by one, one way switches complete all as specified and as directed.

All as per item No 123 above but for one 3 pin socket outlet, 5 Amps on Independent board.

All as per item No 123 above but one 3 pin socket outlet, 5 Amps on the same board with other switches

All as per item No. 123 above but wiring with cables of size 2.5 sqmm & cables of size 2.5 sqmm as continuous earth wire for one 5/15 Amps switch socket combination on Independent board. One 3 pin socket outlet, 5 Amps, independent board.

M&L for point wiring with 1.5 Sqmm (nominal area), FRLSH PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLSH PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point including PVC terminal box (sunken type) with 3mm thick hylam sheet cover fixed with suitable sizes cadmium plated iron screws and washers etc. for mounting switches, sockets, fan regulators etc complete for one light/ fan /bell /buzzer point controlled by one, one way switches complete all as specified and as directed.

All as per item No 127 above but for one 3 pin 5 Amps, socket outlet, on Independent board.

S&F for switch piano, flush type single pole, 230 volts, 5 Amp one way bearing ISI marked complete all as specified and as directed.

Supply and fixing socket outlet 5 pin 5/6 Amp AC 230 Volts flush type complete with all necessary electrical connection,multi-socket outlet independent.

S&F for switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 5 in 1, 5/16 Amps, 240 volts, bearing ISI marked flush type complete all as specified and as directed.

S&F for bell push, flush type, 5 Amps 230 Volts, bearing ISI marked complete all as specified and as directed.

S&F for call bell, AC, 230 volts, single pole complete all as specified and as directed.

S&F for electronic type, white, stepped speed regulator suitable for AC 230 Volts for ceiling fan of sweep 1200mm.

S&F for switch piano, flush type single pole, 230 volts, 5 Amp two way bearing ISI marked complete all as specified and as directed.

S&F for ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body bearing ISI marked and including PVC box complete all as specified and as directed.

S&F in repair lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings including 9 watt LED lamp complete all as specified and as directed.

S&F recess mounted deep drawn PLANO size (2 ft x 2 ft) CRCA housing with higher power 36 Watt LED Seamless front frame with flat white hight transmission acrylic cover complete all as specified and as directed. Make : Cat. No. PLANO 2x2 PLR 36 W LED 840S of Havells or equivalent make of Appendix 'A'.

S&F for 20 Watt surface and wall mounting type LED batten with polycarbonate housing & integrated complete all as specified and as directed. Make : C&S , Cat. No. LTTB4F20WLEDEW BATTEN or equivalent make of Appendix 'A'.

S&F in repairs LED wall bracket light asthetically designed with B22d & E27 lamp holder made up of polycarbonate, suitable for 9/10 including suitable LED bulb complete with all accessories including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to light fittings and taking down old light fittings of any type complete all as specified and dierected. Make :Cat No HLWB-01-B22 of Halonix/ or equivalent make of Appendix 'A'.

S&F in repairs 25 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07 including all fixing arrangement and taking down old light fittings of any type complete all as specified and as directed.

Supply and fixing single pole and neutral enclosure with a two pin and earth Plug and socket complete with one single pole MCB of 20 Amps rating complete all as specified and directed

Supply and fixing in repair of MCB Distribution board SPN 4 Way for mounting SPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed by Engr-in-charge.

S&F for sheet metal enclosure TPN board distribution (DB) having facility to fix MCCB in incomer and MCBs in outgoing, TPN 4 ways, IP-43 with metal door type complete fitted with bus bars , neutral links, blanking plates including making dgood disturb surface, including taking down old unserviceble MCB DB complete all as specified and as directed. Make: Legrand, Cat Pt No. 607913 or equivalent make of Appendix 'A'.

S&F in replacement of MCCB, 4 pole, 415 V with adjustable thermal & adjustable magnetic setting, 160 Amps of breaking capacity 25 KA complete all as specified and as directed.

S&F for factory made board distribution (DB) double door in sheet metal enclosure with common bus bar at incomming end, single pole & neutral, 8 way, 240 Volts suitable for housing MCBs including complete all as specified and as directed.

Supply & fix of MCB double pole 6-32 Amps, 'C' Series 10 KA 240 volts complete all as specified and directed.

Supply & fix in repair of MCB 4P, 63 Amps, 'B' Series 10 KA 240 volts complete all as specified and directed.

Supply & fix of MCB SPN 40 Amps, 'B' Series 10 KA 240 volts complete all as specified and directed.

Supply & fix of MCB DP 6-32 Amps, 'C' Series 10 KA, 240 volts complete all as specified and directed.

Supply & fix of MCB SP 6-32 Amps, 'C' Series 10 KA, 240 volts complete all as specified and directed.

Material and labour for earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanised wire of dia 4 mm as earthing lead by means of nuts, bolts and washers of galvanised iron and earth lead protected by galvanised iron pipe 15 mm bore (light grade) and connected to earth test point and including cement concrete pit in PCC (1:3:6) type C-1(using 20 mm graded aggregate) and pre-cast RCC cover slab of size 540 x 540 x 50 mm thick, reinforced with 8 mm dia TMT bars both ways and one handle for lifting made with 10 mm dia mild steel bar,funnel, wire mesh 20 mm bore galvanised (light grade) for watering, charcoal and salt in alternate layers including necessary execuation and eath works in any types of soil complete all as shown on Electrical plate No 3 of MES SSR-I including taking out the old earthing material complete all as specified and directed. Note:No extra payment will be for the earthing GI wire of size 4 mm dia

Taking down sub main wiring/service connections of any size with condtui/casing caping complete including removal from site and making good disturbed surface of walls/floors etc complete all as specified and directed.

M&L for sub main wiring with two run of 6 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length. (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

M&L for sub main wiring with two run of 4 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 4 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length. (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

M&L for sub main wiring with two run of 10 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size, fixed to wall/ceiling etc including one run of 10 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length. (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

M&L for cutting chases, pinning in brickwalls, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20 cm girth complete all as specified and as directed.

S&F in repair PVC casing caping of size 20-25mm complete all as specified and as directed.

Supply, Laying and testing cable LT XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volt grade, laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including brass cable glands,clamps,etc of 2 core 16 sqmm. Note : (1) Pipes shall be measured and paid separately under relevant items of this schedule. (2) Excvation and earth work shall be measured and paid seperately.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, 3 core, nominal cross sectional area of main conductor 50 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items. (2) Excvation and earth work shall be measured and paid seperately.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, 3 core, nominal cross sectional area of main conductor 70 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items. (2) Excvation and earth work shall be measured and paid seperately.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, 3 core, nominal cross sectional area of main conductor 95 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items. (2) Excvation and earth work shall be measured and paid seperately.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, pipeline etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in, including spreading in layers not exceeding 25cm, levelling, watering and well ramming as in soft/loose soil complete all as specified and as directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above starting point complete all as specified and as directed.

M&L for sand cushioning with dry clean sand 15cm below cable and 8cm above the cable complete all as specified and as directed. Note : Punned thickness shall be measured for payments.

Material & Labour for common burnt clay building bricks (locally available best quality), sub-class ‘B’ designation 75 of suitable size available in market to cover LT underground cables, laid dry and flat abutting each other with gaps not exceeding 10mm including taking down old unserviceable bricks complete all as specified and directed.

S&F inrepair 32 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply & fix exhaust fans metallic body AC single phase 230/240V of size 300mm sweep with louver complete all as specified and directed.

M&L for cutting of circular hole at any type of wall suitable size for fixing of exhaust fan of size 300mm sweep, grouting 04 Nos 100mm long 12mm dia stud bolt including,making good to disturbed surfaces of wall and colour wash to match as per the existing colour complete as directed and specified by engineer-in-charge.

S&F street light bracket fabricated out of GI Tubing light grade 32 mm bore Bend to the shape as directed and of length 1.5 mtr complete with mounting MS clamp of flat iron size 40X5mm of suitable length 02 pairs incl nut bolts etc of suitable size, including taking down old corroded one all as specified and directed.

Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801 ,PP-R pipes SDR 7.4 (PN-16) and PP-R plain plain and brass threaded fittings laid in concealed work complete of size outer dia 25 mm

Supply and fix PPR Gate Valves (Brass Insert) of 25 mm bore.

M&L for Cutting existing pipe of any size for inserting of TEE for connection of PPR pipe of 32mm dia complete all as directed.

S&F for new 9 Watt surface mounted corona type round downlighter for soft diffuser lighting colour temprature is 6000K complete all as specified and as directed. Make : C&S, Cat No. LTCRSUR9HPLEDRND/W or equivalent make of Appendix 'A'.

Taking down decorative fitting any wattage completely keeping in safe costody and after point wiring refixing it in original position complete all as specified and as directed.

M&L for test point terminal box made of gun metal or phosphorous bronze, size 75x75x25 mm drilled and screwd including 3 Nos 8 mm dia 25 mm long hexagonal head screw incl taking down old unserviceable complete all as specified and as directed.

Boring of holes horizontall for laying not less than 40mm pipe (minimum depth 0.75 mtr from top level) under the road pavement, hardstanding using trenchless technology and inserting GI pipe 80/50/40mm bore for drawing the cables complete all as specified and as directed. Note: (1) Cost of accessories required for making hole/bore deemed to be included in the quoted rate. (2) Pipes shall be measured and paid separately under relevant items of this schedule.

M/S CHANDAN ENTERPRISE

Kaushik Enterprises

jitendra narayan goswami

Construction House

MAZUMDAR ENTERPRISE

STANDARD ELECTRIC WINDERS