Maintenance of Motor Pumps in Bidarahalli Gramapanchayat Villages

Supply and fixing of hylumbrand hand plastic sheet3mm thick with necessary nitches for fixing switches, regulators etc and fixing of exciting wood or metal box using NF Screw

Erection of panel Board and MS Box (Outdoor type) (Gulbarga PRED, Pg.No.57, lt.No.12.2)

Supplying and fixing angle ironframe work fabricated out of M.S. angle iron and M.S. flat with bolt, washer etc and painted with 2 coats of red oxide and then two coats of approved paint 75x75x6mm (PWD ELE SR 2014-15, Pg.No.49, lt.No.6.39.3)

Bearing (Gun Metal Bush)centrifugal cost aluminium bronze bearing bush

Stator 10HP (market rate)

Stator 7.5HP (market rate)

Non-Return Valve (NRV) assembly complete with rubber O rings

Impeller Shell moulded with aluminium& bronze

Rewinding of motor of 5.5HP

Fabricating, Supplying and mounting MS Box made out 14 SWG suitable for Foor/Wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front over equipped with temper proof locking arrangements with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colourenamelled metal paint etc

Labour charges for lowering additional GI pipes of dia 32 / 50mm dia including transportation charges (New GI pipe required will be supplied by the department free of cost & released GI pipes should be handed over to the department (Labour charges

pipes should be handed over to the department (Labour charges only)Upto 3 lengths (BWSSB SR 2017-18/O150F/Sl No.29)

Labour charges for lowering additional GI pipes of dia 32 / 50mm dia including transportation charges (New GI pipe required will be supplied by the department free of cost & released GI

Stator 20 HP (market rate)

Stator 17.5HP (market rate)

Stator 15 HP (market rate)

Stator 12.5 HP (market rate)

Steel Bush(I.D.O. SS sleeve)

D.O.Bearing( I.D.OLB bush)

Discharge Outlet (D.O.) Bearing(LB bush) and D.O Steel bushSS sleeve

Oil SealSteel Bush(oil seal sleeve)

OilSeal(pump oil seal)

intermediate Piece (I.P.) withI.P.Leaded Bronze Bush

Rewinding of motor of20HP

Rewinding of motor of17.5HP

Rewinding of motor of 15HP

Rewinding of motor of 12.5HP

Rewinding of motor of10HP

Rewinding of motor of7.5 HP

Rewinding of motor of 5HP

Rewinding of motor upto 3HP

Lifting of struck up submersible pump set above300ft (BWSSB SR 2017-18/O150G/Sl No.27)

Lifting of struck up submersible pump set upto300 ft(BWSSB SR 2017-18/O150G/Sl No.26)

Labourcharges for Lifting of non functioning submersible pump set along with cable and GIpipes

LabourChargesOverhauling

Lifting ofsubmersiblepumpsets

Re-errectioncharges of Pumping machinery including overhauling and painting

Transportationof Pumping machinaries

MotorBase with Pin

Circlips (small)

TipCarbon/FerrodePadding

Thrust Bearin block assembly(TB Bottom)

Carbonhousing(TB Plate)

LockRing(Circlip Big)

LabourCharges (Overhauling of pump only)

Strainer(good quality)

Pumpcoupling(Stainless)

PumpKey (Stainless Steel) Upto 8stages

Pump Shaft (Stainless Steel) Counter less ground with key way upto8stages

G.l.PipeThreading including transportation

LabourCharges (for over hauling)

Supply and fixing of CT coil 50/5&75/5

supply and fixing of Blade set25A

supply and fixing of Blade set16A(MR)

Supply and fixin ofVoltmeter

Supply and fixing ofAmmeter

Supply and fixing ofLEDIndicator

Supply and fixing of wiring kit(SD25HP)

Supply and fixing of wiring kit (DOLupto7.5HP)(MR)

Supply and fixingofNo-Volt (NV) Coil

Supply and fixing of Terminal Plate(connector 60A)

Supply and fixing ofTerminal Plate (connector 30A)(MR)

Supply and fixing ofRYBRotary Switch(volt selector)

Supply and fixing of Single Phase Preventer(20to30HP)

Supplyand fixing of Single Phase Preventer(7.5to15 HP) (MR)

Supply and fixing of15 Amps Relay (MR)

Supply and fixing of 23Amps Relay (MR)

Supply and fixing of 33Amps Relay

Supply and fixing of25 Amps Contactor

Supply and fixing of16 Amps Contactor(MR)

Supplying and fixing polished wood board made out of not less than15mm thick planks at both sides with planks made out of not more than 2 pieces and fixing the same to the wall using tapered wooden plugs screws etc

Refilling available earth around pipe lines, cable in layers not exceeding 20cms in depth compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specification PRE SR 2011-12, P-3,1-6.

Labour charges for Laying U.G.Cable upto3.5 core 25 Sq.mm as per PWD Electrical SR 2010-11, P-68,1-1, Class A PVC cable