CERTAIN REPAIR TO DRAIN, PATH, SECURITY FENCE, BOUNDARY WALL AND OTHER MISC REPAIR WORKS IN AOR OF AGE BR-I UNDER GE(WEST)PATHANKOT

Amount

Dismantling of fencing post or struts (wood, steel, RCC) any section , post embedded in concrete , brick work, masonry etc , including taking out embedded portion and making good disturbed ground complete all as specified and directed.

S & F Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

All as per srl item No. 02 here-in-before but fixing only old mild steel work any type & any size. NOTE: old mild steel work any type & any size retrieved from dismantling shall be used.

Dismantling of fencing wire mesh of any type or any description, complete all as specified and directed.

Excavating in post hole or similar hole each n.exc. 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc. 25 cm, watering and removing surplas soil to adistance not exc. 50 mtr and making good surface in hard / dense soil complete all as specified and as directed by Engg-in-Charge.

S&F chain link MS galvanised fencing of mesh size 100mm x 100mm, made with 3mm dia GI wire, any type, including line wires, including standards, rails, straining bolts, etc. Including provision of binding wire complete all as specified and directed.

M & L for PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe-410-W 432 (Part I) (Gde.E-250) Part- I quality-A or Fe 290 (Gde -E-165)

S & F in repair mild steel screw bolts with hexagonal or square heads at one end and screwed at other end fitted with washers and one hexagonal nut exc 5cm but n exc 10cm long and 12 mm dia complete all as specified and directed.

S & F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

All as per srl item No. 10 here-in-before but except barbed wire. (NOTE: Old Serviceable steel any type/size barbed wire quantity retrieved from dismantling shall be used.)

M&L for Providing and fixing concertina coil fencing with punched tape concertina coil 610mm dia Including dismantling with following specifications:- (i) Coil Dimension :- (a) Coil opening diameter (610mm+20mm, -0mm) before stretching. b) When stretched upto 6 meter length -coil diameter not less than (580mm+20mm-0mm) c) Coil having 50 Nos spiral turns & 129 nos clips in 06 meter length and weight not less than 9Kg + 5% excluding spike and handles (ii) Razor barb BTO-22 a) Barb thickness 0.5mm (+- 0.05mm) b) Barb width 15mm (+-1mm) c) Barb length 22mm (+-1mm) d) Barb spacing 35mm (+-1mm) e) Steel strip (punched tape/RBT)= The punched tape shall be CR3 grade cold reduced low carbon steel as per IS 513:2008 with pre painted Aluminium Zinc alloy in accordance with IS 15965:2012/AZ150/Class 3. (iii) Spring Core wire (a) Nominal dia of uncoated wire = 2.59mm (+-0.035mm) b) Galvanisation = The core wire should have thickness of hot dipped galvanised zinc to 290 g/m2 minimum as per the specification BS EN ISO 1461, Similarly, Indian Specification IS 4826. d) High tensile strength not less tann 1620 N/Sqmm iv) Heavy duty "J" clip for attachments" a) Material= SS 304 Stainless steel b) Dimension= 29mm x 8mm x 1.6mm

Demolition of RCC work, Roofs, floors , beams staircases, landing, chajjas, & similar suspended work cement concrete is reinforced (reinforcement cut as required to facilitate demolition)

M & L for 35mm thick providing precast cement concrete louvers and jallies (measured solid) in 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate set in cement mortar 1:4, including all mouldings but excluding frame complete all as specified and as directed. Note: Pre-cast frame shall be measured separately & demolition will be measured with demolition of RCC work.

M & L for Precast cement concrete type B-1 (1:2:4) using 20 mm graded crushed stone aggregate in window or door cills, lintels, bressumers, steps, kerb stone, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), balusters with plain fair faces, including chamfers, weatherings, throating etc. and setting in CM(1:6) with joints to match complete all as specified and directed. (Note : Demolition will be measured with demolition of RCC work)

M & L for precast reinforcement cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in cover slabs( for manholes , drain etc.)chulla hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:6) complete all as specified and as directed. Note:- Reinforcement shall be measured and paid separately).

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil. Note:-(1) The excavation work will be carried out by manually or mechanical means in any location/ area as directed by Engr-in- charge. (2) Any damage occur to water supply pipe line/electric cable etc during excavation work will be make good up to satisfaction of Engr- in-charge without any extra cost to the govt.

M & L for Reinforced concrete pipes, class NP-3, laid and jointed complete with collars of 300 mm internal dia laid in trenches including testing complete including demolition and breaking up drain pipes in cement mortar including demolition of PCC bedding and hunching complete all as specified and directed

M&L for Concrete bed to drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested in Cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate for Bore of pipe in 300 mm complete all as specified and directed

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm with any type of soil.

Removing excavated Soils material exc. 250m but n exc. 500 m and depositing where directed

Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar including all quions,wall, arches, pillars,man-holes,drain, septic tank,soak well also in foul condition etc complete all as specified and directed.

M&L for Brick work, using fly ash bricks of old size bricks having crushing strength not less than 75kg/Sqcm, straight or curved on plan, exceeding 6 m mean radius, built in cement mortar 1:4 complete all as specified

M & L for burnt clay brick work with sub-class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

All as per srl item No.24 here-in-before but except bricks. NOTE: Old Serviceable bricks quantity retrieved from demolition shall be used.

M & L for half burnt brick work with subclass ‘B’ old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

Demolition of cement concrete or lime concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing the debris complete all as specified and directed .

M&L for plain cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate in copings, kneelers, apex stones,bed plates, kerbs including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for PCC in foundations, filling and mass-concrete type D-2 (1:4:8) using 40 mm graded crushed stone aggregate complete all as specified and directed.

M & L for PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and as directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed. Note:- Inner girth shall only be measured

Demolition of cement concrete or lime concrete (unreinforced) in ground floors and Paving not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed .

M & L for 40 mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) finished even and smooth without using extra cement as in flooring complete all as specified and directed.

S&F 38 mm wide and 3 mm thick glass dividing strips in flooring by fixing in position and making square or rectangle for casting concrete is flooring complete all as specified and directed.

M&L for Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving 75mm thick laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight and complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing) removing serviceable tiles to store and rubbish off the premises and removing the debris outside from defence land complete all as specified and directed .

M&L for Non abrasive paving cement concrete coloured tiles 300 mm x 300 mm x 10 mm thick set jointed and pointed in neat cement slurry mixed with pigment laid over 15 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed. Note:-The texture , colour, size ,Shade of tiles & laying of tiles to any pattern & any design with one or more colours shall be approved by GE.

S&F Cement concrete tiles 25cm x 25cm x22mm thick, with grey cement & pigment machine pressed; set, jointed & pointed in neat cement slurry in floors ,path & cut , polished over and including 20mm thick secreed bed or bedding in CM 1:6 complete all as secified and as directed.

M&L for 50 mm thick cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in path/floor etc finished even and smooth without using extra cement including complete all as specified and as directed

M & L for 75 mm thick plain Cement concrete 1:4:8, type D-2 using 40mm graded crushed stone aggregate as in sub base/Flooring complete all as specified and as directed.

M & L machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 80 mm thickness, M-40 grade rubber moulded glossy finish with grey cement and pigment complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks,laying pattern approved by GE.

M & L for machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade rubber moulded glossy finish with grey cement and pigment complete all as secified and as directed. Note-Shapes of interlocking paver block shall be triangular/Zigzag/Haxagon/or other ,Colour of paver blocks,laying pattern approved by GE.

M & L for sand filling under floors or in foundations including watering and consolidation or layer of sand cushioning below interlocking paver block complete all as specified and as directed.

M&L for 18-20mm thick granite (pure black) work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform,flooring, gate pillars ,and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite & all open edges to be half rounded over including 15mm thick screed bed or bedding layer in cement mortar 1:4 including dismantling of existing stone slab etc complete all as specified and directed.

M&L for Marble work 18 to 20mm thick of any coloure (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms , flooring and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade & all open edges to be half rounded over & including 15mm thick backing coat/redering in cement mortar 1:4 for fixing including dismantling of old stone slab etc complete all as specified and as directed.

Grinding with machine grinder of granite stone /terrazzo topping with marble aggregate /marble Stone slab / kota stone slab etc. as in old floor, wall, cooking platform, shelf etc & polishing complete all as specified and directed.

Dismantling of Stone slabs & tiles of any description or thickness in floors, aprons etc. Laid, bedded & pointed in any mortar

M & L for machine cut kota stone slab flooring 18-20mm thick (not less than size 550mmx550mm)over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over screed bed or bedding layer 20 mm thick in cement mortar 1:4, complete all as specified and as directed.

M & L for machine cut kota stone slab 16mm thick in riser of steps, skirting, dado and pillar laid over backing coat 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed.

Dismantling timber scantlings 40sqcm and over in section, in any position as in wooden trusses in framed work of any description.

M&L for IInd class hard wood in scantling Clean sawn timber work of suitable size of any shape fixed with screws or nails all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for including grills, door, truss, gate, rafters, purlins etc

M&L for mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;l adders; framed balusters; walk ways; railings; framework of water tanks, cattle trap and similar work conforming to Fe.290.Gde-E-165,ornamental and intricate design complete all as spd and directed.

M&L for mild steel ornamental , intricate design and decorative type steel gate Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, rolling track (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe 410-W Gde E-250 of quality ‘A’ complete all as specified and as directed.

M&L for Roof trusses (mild steel framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) Fe410 gde E-250 quality B including distance pieces, cleats etc..

M&L for Two coat of synthetic enamel paint over a coat of red oxide primer to new steel surface including preparation complete all as specified and directed.

S&F in repairs Traffic convex Mirrors body colour black in Polycarbonate/ Stainless steel with Dome size is 30" and 36" in Dia with GI pole of suitable height for ground requirement and necessary excavation, PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) 0.45 x 0.45 x 0.60 metre, location moving & etc as directed by GE. Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI / VERTEX.

S & F in repair mild steel, plain, black sheet 1.60mm thick in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

M&L for preparation of newly steel and iron surface of any description width or girth exc 10 cm and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling of Asbestos/fibre cement/PVC sheet (corrugated,semi corrugated, etc.) sheets in roof coverings including ridges etc.

M&L for 2 mm Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with, if fixed with L-type or J-type or cranked hook bolts in lieu of screw → coach screw and washer in roof, wall etc.

S&F galvalume aluminium zinc coating corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed by Engr-In-Charge.

S&F in replacement Factory made Rectro reflective road sign comprising of plates of size 1500 x 900 mm fixed , one above the another made of 2 mm thick aluminum sheet duly framed in stainless steel 40mm bore pipe. The plates fixed with aluminum rivets and written on both side indicating the directions, alphabets, arrow, lines, diagrams etc on each sides with computerized cut letters and signs (reflective) as directed of appropriate size and white in colour and dennison HIP base green. The boards (Plates) dully fitted with stainless steel 40 mm bore top height of boards with legs from ground level minimum 2.50m each including embedding in PCC (1:2:4) type B 1 block of size 30 Cm x 30cm x 60 cm including earthwork excavation and taking out old sign board any type all as per sample kept in GE office and as directed by Engr-in-charge (pegged sign board fully reflective). Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI.

S&F in replacement Factory made Rectro reflective road sign boards comprising of plates of size 1200 x 800 mm fixed , one above the another made of 2 mm thick aluminum sheet duly framed in stainless steel 40mm bore pipe. The plates fixed with aluminium rivets and written on both side indicating the directions, alphabets, arrow, lines, diagrams etc on each sides with computrised cut letters and signs (reflective) as directed of approiate size and white in colour and dennison HIP base green. The boards (Plates) dully fitted with stainless steel 40 mm bore top height of boards with legs from ground level minmum 2.50m each including embedding in PCC (1:2:4) type B 1 (using 20mm graded crushed stone aggregate) block of size 30 Cm x 30cm x 60 cm including earthwork excavation and taking out old sign board any type all as per sample kept in GE office and as directed by Engr-in-charge (pegged sign board fully reflective). Make : GREEN LIGHT /GREEN /DARK EYE/ENS/ GUNNEBO/SHAKTI.

Taking down existing any type of Steel rolling shutters of any size/type/thickness, with or without ball bearing, as specified including top cover, anchoring rod, hasp ,staple as erected in position as indicated, push pull or manual type, gear operated type with bevel gear box and crank handle, gear operated type with chain wheel and hand chain, or self closing type, and re-fixing in the same opening after carrying out necessary repair, replacing damaged parts of shutter, welding, oiling ,greasing, lubricant to guide rail, gear box etc including straightening of any covering dented items sheet ,strip, laths, hood cover, guide rail and tightening of rolling springs, repair to old bevel gear box for any size of opening including replacement of unserviceable items required for smooth functioning of the rolling shutters including applying two coats of synthetic enameled paint over a coat of red oxide primer including preparation of surface, make the all system fully functional to the entire satisfaction of Engr-in-Charge complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar, and taking out of trenches, if required, Internal dia of pipe in 75MM/100mm

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as spd and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as spd and directed.

S&F PVC (SWR) bends any radius 75mm dia complete all as spd and directed.

S&F PVC (SWR) bends any radius 110mm dia complete all as spd and directed.

M&L for Running welding in repairs thickness of metal to be welded exc Exc 09 mm but n exc 20mm complete all as directed.

M&L for Welding in repairs exc 2.5cm but n exc 5cm in length & thickness of metal to be welded exc Exc 09 mm but n exc 20mm complete all as directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc including necessary scaffolding up to four storeys bldgs height if required at site including cleaning of drops, splashes and leaving premise clean and tidy & removing of debris complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement including necessary scaffolding up to four storeys bldgs height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

M&L for rendering 10 mm thick in CM 1:4 mixed with liquid water proofing compound (as per manufacturer’s instructions) on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement including necessary scaffolding up to four storeys bldgs height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

M&L for 5 mm thick rendering on brick work or concrete surfaces in CM 1:3 as in ceiling of roof slab ,fin, facia, culvert, chajjas, parapet and similar article etc finishing surfaces even and smooth without using extra cement including necessary scaffolding up to four storeys bldgs height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

Supply only liquid water proofing compound all as specified and as directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of weather proof exterior emulsion paint in any tint without any brush marks on the surface & matching with existing work over and including one coat of primer (as per manufacturer’s recommendations) including necessary scaffolding any height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

M&L for complete removal of existing treatment surface of wall and applyingtwo coats of weather proof exterior emulsion Paint in any tint over and including one coat of primer (as per manufacturer’s recommendations) without any brush marks on the surface in any colour & matching with existing work over and including a coat of alkali resistant primer (as per manufacturer’s recommendations) including necessary scaffolding any height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying applying two coats of Cement Base Paint in any tint over and including one coat of alkali resistant primer (as per manufacturer’s recommendations)

M&L for preparation of old plastered or unplastered ,old/un decorated surfaces of wall surface by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coats of Cement Base Paint in any tint without any brush marks on the surface & matching with existing work including necessary scaffolding any height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

Preparation of new surfaces of ceiling and application of three coats of white washing completed as specified and directed.

All as per srl item No 82 here-in-before but one coat of white wash on old surface of ceiling.

M&L for complete removal of existing treatment of old plastered or unplastered or old decorated wall surface (internal) by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and with 3mm thick wall care putty and applying two coat of distemper oil emulsion in any tint on wall surface (internal surface) without any brush marks & matching with existing work including necessary scaffolding up to four storeys bldgs height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

M&L for applying two coat of synthetic enamel paint over and including one coat of primer (as per manufacturer’s recommendations) on any type of brick, kerb stone, concrete, asbestos cement, Heritage/textures/Granules/grit finish or plaster surface in any description, in any colour, on floor/wall surface over 10cm girth or width, not otherwise described, finished without brush mark & matching with existing work/ surface including preparation of old surface including necessary scaffolding up to four storeys bldgs height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

M & L for preparation of old painted wooden surfaces of any description over 10 centimeter width or girth and applying one coat of synthetic enamel paint in any colour finished without brush mark on surface including necessary scaffolding up to four storeys bldgs height if required at site including cleaning of drops, splashes and leaving premise clean and tidy complete all as specified and as directed.

All as per Srl item No. 86 here-in-before but on steel surfaces

Taking down old any type description of Heritage ,Texture finished surface including preparation of surface and M & L for applying heritage/Texture finish surface such as fine flakes features/heritage flakes textures features/heritage granite finish/ heritage granules finish/ heritage surface textures/metallic/stone finishes/natural finishes/super matt paint finish/fine flakes /fine granules etc complete application process as per manufacturer’s recommendations in any tint design & pattern as approved by GE including bonding agent & top coat including trowelled on the surface on internal or external surfaces including matching with existing work including necessary scaffolding any height height as required at site complete all as specified and as directed. Make :-(a) Unitile (b) Bakelite Hylam (Heritage). (c) Dulux (acratex)(d) Apex (Duracast). (Note: All painted areas site to be cleaned and hand over as earlier without any extra cost to Govt)

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and directed.

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 73,895.00 and any other reduction if any from quoted amount.

M/S SATYA SAI CONSTRUCTION (BID ID -3381831)

malghotra construction co (BID ID -3384585)

DABGOTRA BUILDERS (BID ID -3384680)

M/S RELIANCE ENGINEERS (BID ID -3383576)

M/S Raghuvanshi Builders (BID ID -3385154)

VAISHNAVI BUILDERS (BID ID -3384873)