UPGRADATION OF INTERPRETATION CENTER FOR VISITORS AT SARNATH

Amount

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge in cement mortar.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 meters lead as per direction Nominal concrete 1:3:6 or richer mix (i/c equivalent design charge.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Dismantling aluminum/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material within 50 meters lead as directed by Engineer-in-charge.

Dismantling doors, windows, chair and table, chair railing fixed disposal of unserviceable material and stacking of serviceable material within 50 meters lead as directed by Engineer-in-charge.

Brick work with common burnt clay FPS (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand).

Provision for 12 mm cement plaster 1:4 (1 cement: 4 fine sand) with all material and labour, curing work as per direction of Engineer-in-charge.

6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams.

Providing and laying six courses water proofing treatment with bitumen felt over roofs consisting of first, third and fifth courses of blown or / and residual bitumen applied hot at 1.45, 1.20 and 1.70 kg per square meter of area respectively, second and fourth courses of roofing felt type 2 grade I (fiber base self-finished bitumen felt) six and final courses of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per sqm including preparation of surface, excluding grading, compete.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel l50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm center to center with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm center to center by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm center to center, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm center to center. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks).

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm center to center, one flange fixed to the ceiling with as hfastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of an glehanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm center to center, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm center to CENTER, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm center, with 25mm long drywall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of drywall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks).

Provision for fitting and fixing of all electrical articles with all fixtures as per detailed material & labour charges etc., complete. 25 mm wiring pipe- 2 bundle 25 mm band- 0.9 cum 1.5 mm copper wire- 10 nos 2.5 mm copper wire- 8 nos 0.75 mm copper wire- 3 nos 25 mm kaju pin- 3 nos 25 mm flexible pipe- 4 nos Tap- 19 nos 3 model metal box- 4 nos 6 model metal box- 3 nos 25 mm kaju pin- 2 nos PVC junction- 4 nos 18 model plate- 1 nos 18 model gang box- 1 nos 6 AMPR switch- 35 nos 16 AMPR socket- 2 nos 10 AMPR mini MCB– 5 nos 63 AMPR 4 pole MCB- 3 nos 16 model MCB box- 1 nos 6 model plate- 2 nos 16 AMPR witch- 2 nos Light panel 15 w-15 nos 12 model box- 1 nos 1 mm copper wire- 2 nos Philips 31446 stanchion track light 20 w-40 nos Stanchion track light suspension AMTR black-47 rmt 4 pole 16 mm armed wire- 80 nos 3' x 3' iron pipe 3mtr in length for sliding toughen glass door imbedded in wall- 10 LS electrician charges- 1 job

Provision for Daikin cassette Air conditioner including all fitting & fixing with required accessories, connection, cabling etc, complete. 3 ton caset AC-2 nos 2ton caset AC- 1 nos out door 3ton- 2 nos out door 2ton- 1 nos caset AC grill 3ton- 2 nos caset AC grill 2ton- 1 nos wireless receiver kit-2 nos Stand- 4 nos 4 mm copper wire-4 bundle 1 mm copper wire- 1 bundle 25 mm flexible pipe- 5 bundle tie rod 8 mm- 22 nos Fasner- 12 nos Copper pipe set 5/8+3/8- 60 rmt Copper pipe set 5/8+1/4- 42 rmt installation charges- 1 job

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @0.75 ltr /10 sqm

Provision for LG LED 75 UT80406LA TV display including installation charges, fitting & fixing in position with all required accessories etc, complete

Provision for fitting and fixing of sanitary article with all fixtures material & labour charges etc., complete. Tab Jaguar- 2 nos Provision for wash basin stand with fixing on black stone platform- 2 nos Rimless, Blind Installation Wall Hung WC- 2 nos Rag Bolts- 2 nos Control Plate Connectional prime- 2 nos Single Piece slim concealed cistern- 2 nos hand Shower- 2 nos 110 MM type A GSS pipe 3 mtr- 2 nos CPVC pro pipe CTS- 2 nos CPVC pro Coupler SDR- 2 nos Installation charge- 2 job

Provision for providing salwood table with cusion as per approved design with all fitting and fixing including wood polish etc., complete.

Provision for 2mm thick vinyl mat flooring of size 152.4mmx914.4mm pasted with synthetic rubber adhesive fevicol including fitting & fixing with all material and labour charge etc., complete.

Provision for 4 battery 200ah and Invertor 200ah including fitting with all fixtures with all accessories complete.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing glazing in aluminum door, window, ventilator shutter sand partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminum snap beading shall be paid in basic item)With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm).

Provision for supply of locker almirah for keeping tourist luggage for safety & security purpose

Provision for Frosted Film for Glass Privacy Strips Design Glass Sticker with cutting in size and shape including pasting charges etc complete.

Provision of exhibition boards for interpretation center and sculpture shed at site in wooden farming with printing in canvas including pasting, installation etc. all complete.

Provision of different size signage’s in SS, including printing, pasting and installation etc.

M/S DINESH SHUKLA (BID ID -3280685)

M/S Raj Construction (BID ID -3280866)

Neeraj Kumar Pandey (BID ID -3280228)