SEES/SHIMLA-321/2023-24

Amount

Supply Part of HT line as per standard design/specification approved by HPSEBL.

Cross Arm: [Channel Iron (100x50x6 mm),Length (2800) mm.

Belt Set - MS Angle Iron: 65x65x6, Length 1800 mm.x2No)

X-Bracing Set - MS Angle Iron: 50x50x6, Length 2700mm x 2No)

Discs insulator sets on Dead End structures (comprising 1 No. Disc (Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

22 KV Pin insulater (Polymer,22kv.)

Prov.Egg Insulator.

Bend stapple

Line stapple

Ball Cleave Eye Socket 11 kV/22 kV 7500 GMS

HT Stay / Guy Arrangement

Stay set complete in all respect (5 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Earthing

Prov. HT Earthing set complete with salt and charcoal 50Kg each.

Single Continous Earth wire (GI, 8 SWG) {alongwith 1 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Prov. Eye Hook for earth wire

Earth wire Clamp

Prov.Danger Plate (250X200X1.6 mm)

Prov. Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Prov. Aluminium Paint

Prov. Half clamp

Prov. Stay clamp

Prov. Support clamp

Errection of 22KV HT Line.

Manual carriage of 22KV HT line material

Manual carriage of Steel Tabular Poles 11Mtr./13Mtr Long with RCC Muff, HT line material from Road side to site of work avg. lead 1.69Km

Mechanical carriage of sub-station material for an average distance of 1.69Km. i/c loading & unloading. (carriage of avg. 6 Nos. ST Poles in 1 trip.)

Erection of 22KV HT line

Erection of steel tubular poles 11/13 mtr.long Double pole str. Digging of pit , erection of pole , filling of pit ramming , drilling of holes in poles & X-Arms, fixing of insulator , X-Arm, Knee bracing set , fixing of danger plate, painting of poles complete in all respect .

Earthing

Digging of pits , fixing of earth wire to the earth system , filling of pit etc.

Stay Set (HT)

Digging of pit, fixing of stay Rod, Filling of Pit & Nozzeling & Tighting.

Erection of RCC Muffs with Concreting filling

Sagging of conductor 1Km. Single wire ACSR Cond. 100mm2

Laying of conductor, stringing and sagging , binding with insulator (Single wire)

Laying of continuous Earth wire.(Single wire )

Laying of GI wire , stringing and sagging and jumpering and guarding etc.

Foundation & Protection

Cutting in earthwork in all kind of soil and disposal of excavated earth in all kind of lead and lifts. (a) 50% Pick work (b) 50% Jumper work.

Excavation in foundations, trenches etc. in earth work , lift up to 1.5m stacking the excavated soil not more than 3.00 m clear from the edge of the excavation and then returning the stacked soil in 15 cm. layers when required in to the plinth side of the foundation etc. Consolidating each deposited layer by ramming and watering and then disposing of all the surplus excavated earth for all leads /lift and for all kinds of soil. (a) 50% Pick work (b) 50% Jumper work.

Providing and laying cement concrete 1:5:10 (1cement :5 sand :10 graded stone aggregate 40mm.nominal size) with 15 % plum and curing complete, the size of plums shall usually be 150mm. to 300mm.as per H.P.P.W.D. Specification.

Providing and laying PCC 1:6:12 (1cement :65 sand :12 graded stone aggregate 40mm. nominal size) and curing complete excluding cost of form worm in foundation plinth in breast and retaining wall etc.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battening and soiling height of propping and centering below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for in situ-reinforced concrete and plain concrete work including all leads and lifts of materials in Foundation, footings base of columns etc and mass concrete.

Protection Work

Providing protection wall around the D/Pole structures in cement concrete 1:5:10 (1cement: 5sand: 10graded stone aggregate 40mm) with 15% plum and cutting complete, the size of plums shall usually be 150mm to 300mm as per HPPWD specifications

ubish chander

JITENDER SINGH CONTRACTOR