Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹43.4 LAccepted-AOC | L1 | Accepted-AOC BEING LOWEST | |
| 2 | L2₹45.3 L+₹1.5 L (3.45%)Rejected-Finance | L2 | Rejected-Finance NOT BEING LOWEST | |
| 3 | Rejected-Technical 704 SILVER DEAL DAFFODIL WING 1 B T KAWADE ROAD PUNE 411 001 | PUNE | PUNE | MAHARASHTRA | 411001 | - | Rejected-Technical NOT ENLISTED IN APPROPRIATE CATEGORY |
| Sl No | Description | Qty | Unit | B5BUILDING SOLUTIONS L1 | shanti enterprises L2 |
|---|---|---|---|---|---|
| 1.00 | Supply, installation, commissioning and testing factory made LT panel board of CPRI approved, as per IEC-61439, suitable for 3 phase, 4 wire, 440 Volts AC supply, outdoor cubical type, size not less than 1200x1200x600 mm dust and vermin proof powder coated, made out of 3.15 mm thick CRCA sheet with angle iron frame made out of MS angle 50 x 50 x 6 mm both sides openable double door type with proper locking arrangements duly finished with powder coated paint of approved colour over a coat of red oxide primer all over steel surfaces with 75 cm high angle iron legs welded on four corners of frame embedded in PCC (1:2:4) using 20 mm graded stone aggregate upto 30cm height foundation and proper glanding, lugs and nuts, bolts etc for all cables and comprising of following accessories including disconnecting and taking down existing panel complete all as directed with sufficient working space with and including to accommodate the following accessories: - | 1 | EACH | 6,15,000 ₹6,15,000 | 2,83,000 ₹2,83,000 Lowest |
| 1.01(a) Aluminium bus bar of 1000 Amps rating 3 phase 4 wire system. (b) Digital Voltmeter 0-500 V - 01 No. (c) Digital Ammeter 0-800 Amps with CTs – 01 Set. (d) LED type indicator 230 volts for RYB – 01 Set. | |||||
| 1.02Incoming:- (a) ACB 4 pole, 415 volts with thermal magnetic release (Manual Drawout type) of capacity 800 Amps. | |||||
| 1.03Outgoing:- (a) MCCB 415 volts, 4 pole 200 Amps with breaking capacity 36 KA – 05 Nos. (b) MCCB 415 volts, 4 pole 100 Amps with breaking capacity 16 KA – 02 Nos. | |||||
| 2.00 | Supply, installation, commissioning and testing factory made LT panel board CPRI approved,as per IEC-61439, suitable for 3 phase, 4 wire, 440 Volts AC supply, outdoor cubical type, size not less than 1200x1200x600 mm,dust and vermin proof powder coated, made out of 3.15 mm thick CRCA sheet with angle iron frame made out of MS angle 50 x 50 x 6 mm both side openable double door type with proper locking arrangements duly finished with using powder coated paint of approved colour over a coat of red oxide primer all over steel surfaces with 75 cm high angle iron legs welded on four corners of frame embedded in PCC 1:2:4 using 20 mm graded stone aggregate upto 30 cm foundation and proper glanding, lugs and nuts bolts etc for all cables and comprising of following accessories including disconnecting and taking down existing panel etc complete all as directed with sufficient working space with and including to accommodate the following accessories :- | 1 | EACH | 6,05,000 ₹6,05,000 | 2,58,000 ₹2,58,000 Lowest |
| 2.01(a) Aluminium bus bar 1000 Amps rating 3 phase 4 wire system. (b) Digital voltmeter 0-500 V - 01 Nos. (c) Digital ammeter 0-800 Amps with CTs – 01 Set. (d) LED type indicator 230 volts for RYB – 01 Set. (Location: Near Directors Bungalow) | |||||
| 2.02Incoming:- (a) ACB 4 Pole, 415 volts with Thermal Magnetic Release (Manual Drawout type) of capacity 630 Amps. | |||||
| 2.03Outgoings:- (a) MCCB 415 volts, 4 pole 160 Amps with breaking capacity 36 KA – 05 Nos. (b) MCCB 415 volts, 4 pole 100 Amps with breaking capacity 16 KA – 02 Nos. | |||||
| 3.00 | Supply, installation, commissioning and testing factory made LT panel board CPRI approved ,as per IEC-61439, suitable for 3 phase, 4 wire, 440 Volts AC supply, outdoor cubical type, size not less than 1200x1200x600 mm, dust and vermin proof powder coated, made out of 3.15 mm thick CRCA sheet with angle iron frame made out of MS angle 50 x 50 x 6 mm both side openable double door type with proper locking arrangements duly finished with using powder coated paint of approved colour over a coat of red oxide primer all over steel surfaces with 75cm high angle iron legs welded on four corners of frame embedded in PCC (1:2:4) using 20 mm graded stone aggregate upto 30 cm height foundation and proper glanding, lugs and nuts bolts etc for all cables and comprising of following accessories including disconnecting and taking down existing panel etc complete all as directed with sufficient working space with and including to accommodate the following accessories: - | 1 | EACH | 5,99,000 ₹5,99,000 | 2,33,000 ₹2,33,000 Lowest |
| 3.01(a) Aluminium bus bar 1000 Amps rating 3 phase 4 wire system. (b) Digital voltmeter 0-500 V - 01 Nos. (c) Digital ammeter 0-800 Amps with CTs – 01 Set. (d) LED type indicator 230 volts for RYB – 01 Set. | |||||
Tender Value
₹48 L
EMD Value
₹96,000
Closing Date
6 Oct 2025, 6:00 pmClosed
LT COL CHANDRAKANT JOSHI
DRDO Complex, CV Raman Nagar PO, Bangalore 560 093
REPAIRS MAINTENANCE TO FIRE FIGHTING SYSTEM FIRE HYDRANTS FIRE ALARM SYSTEMS CONTROL PANELS AND LT PANEL LT CABLE AND CONNECTED MISC ITEMS AT PHASE II RESIDENTIAL AREA UNDER GE I R AND D EAST BANGALORE
2025_MES_723209_1
8637/E8
Open Tender
Electrical and Maintenance Works
Item Rate
270 days
GE I R AND D EAST BANGALORE
CLASS D CATEGORY c(vi)
8 documents required · 8 mandatory
₹500
Yes
GE I R AND D EAST BANGALORE
₹96,000
Yes
3 Dec 2025
9 Sept 2025
13 Oct 2025
9 Sept 2025
6 Oct 2025
23 Sept 2025
9 Sept 2025 - 22 Sept 2025
Amount
Supply, installation, commissioning and testing factory made LT panel board of CPRI approved, as per IEC-61439, suitable for 3 phase, 4 wire, 440 Volts AC supply, outdoor cubical type, size not less than 1200x1200x600 mm dust and vermin proof powder coated, made out of 3.15 mm thick CRCA sheet with angle iron frame made out of MS angle 50 x 50 x 6 mm both sides openable double door type with proper locking arrangements duly finished with powder coated paint of approved colour over a coat of red oxide primer all over steel surfaces with 75 cm high angle iron legs welded on four corners of frame embedded in PCC (1:2:4) using 20 mm graded stone aggregate upto 30cm height foundation and proper glanding, lugs and nuts, bolts etc for all cables and comprising of following accessories including disconnecting and taking down existing panel complete all as directed with sufficient working space with and including to accommodate the following accessories: -
(a) Aluminium bus bar of 1000 Amps rating 3 phase 4 wire system. (b) Digital Voltmeter 0-500 V - 01 No. (c) Digital Ammeter 0-800 Amps with CTs – 01 Set. (d) LED type indicator 230 volts for RYB – 01 Set.
Incoming:- (a) ACB 4 pole, 415 volts with thermal magnetic release (Manual Drawout type) of capacity 800 Amps.
Outgoing:- (a) MCCB 415 volts, 4 pole 200 Amps with breaking capacity 36 KA – 05 Nos. (b) MCCB 415 volts, 4 pole 100 Amps with breaking capacity 16 KA – 02 Nos.
Supply, installation, commissioning and testing factory made LT panel board CPRI approved,as per IEC-61439, suitable for 3 phase, 4 wire, 440 Volts AC supply, outdoor cubical type, size not less than 1200x1200x600 mm,dust and vermin proof powder coated, made out of 3.15 mm thick CRCA sheet with angle iron frame made out of MS angle 50 x 50 x 6 mm both side openable double door type with proper locking arrangements duly finished with using powder coated paint of approved colour over a coat of red oxide primer all over steel surfaces with 75 cm high angle iron legs welded on four corners of frame embedded in PCC 1:2:4 using 20 mm graded stone aggregate upto 30 cm foundation and proper glanding, lugs and nuts bolts etc for all cables and comprising of following accessories including disconnecting and taking down existing panel etc complete all as directed with sufficient working space with and including to accommodate the following accessories :-
(a) Aluminium bus bar 1000 Amps rating 3 phase 4 wire system. (b) Digital voltmeter 0-500 V - 01 Nos. (c) Digital ammeter 0-800 Amps with CTs – 01 Set. (d) LED type indicator 230 volts for RYB – 01 Set. (Location: Near Directors Bungalow)
Incoming:- (a) ACB 4 Pole, 415 volts with Thermal Magnetic Release (Manual Drawout type) of capacity 630 Amps.
Outgoings:- (a) MCCB 415 volts, 4 pole 160 Amps with breaking capacity 36 KA – 05 Nos. (b) MCCB 415 volts, 4 pole 100 Amps with breaking capacity 16 KA – 02 Nos.
Supply, installation, commissioning and testing factory made LT panel board CPRI approved ,as per IEC-61439, suitable for 3 phase, 4 wire, 440 Volts AC supply, outdoor cubical type, size not less than 1200x1200x600 mm, dust and vermin proof powder coated, made out of 3.15 mm thick CRCA sheet with angle iron frame made out of MS angle 50 x 50 x 6 mm both side openable double door type with proper locking arrangements duly finished with using powder coated paint of approved colour over a coat of red oxide primer all over steel surfaces with 75cm high angle iron legs welded on four corners of frame embedded in PCC (1:2:4) using 20 mm graded stone aggregate upto 30 cm height foundation and proper glanding, lugs and nuts bolts etc for all cables and comprising of following accessories including disconnecting and taking down existing panel etc complete all as directed with sufficient working space with and including to accommodate the following accessories: -
(a) Aluminium bus bar 1000 Amps rating 3 phase 4 wire system. (b) Digital voltmeter 0-500 V - 01 Nos. (c) Digital ammeter 0-800 Amps with CTs – 01 Set. (d) LED type indicator 230 volts for RYB – 01 Set.
Incoming:- (a) ACB 4 pole, 415 volts with Thermal Magnetic Release (Manual Drawout type) of capacity 630 Amps.
Outgoing:- (a) MCCB 415 volts, 4 pole 200 Amps with breaking capacity 36 KA – 01 No. (b) MCCB 415 volts, 4 pole 160 Amps with breaking capacity 16 KA – 04No, (c) MCCB 415 volts, 4 pole 100 Amps with breaking capacity 16 KA – 02Nos.
Supply, installation, commissioning and testing factory made LT panel board CPRI approved ,as per IEC-61439, suitable for 3 phase, 4 wire, 440 Volts AC supply, outdoor cubical type, size not less than 1200x1200x600 mm, dust and vermin proof powder coated, made out of 3.15 mm thick CRCA sheet with angle iron frame made out of MS angle 50 x 50 x 6 mm both side openable double door type with proper locking arrangements duly finished with using powder coated paint of approved colour over a coat of red oxide primer all over steel surfaces with 75 cm high angle iron legs welded on four corners of frame embedded in PCC (1:2:4) using 20 mm graded stone aggregate upto 30 cm height foundation and proper glanding, lugs and nuts bolts etc for all cables and comprising of following accessories including disconnecting and taking down existing panel etc complete all as directed with sufficient working space with and including to accommodate the following accessories: -
(a) Aluminium bus bar 1000 Amps rating 3 phase 4 wire system. (b) Digital voltmeter 0-500 V - 01 Nos. (c) Digital ammeter 0-800 Amps with CTs – 01 Set. (d) LED type indicator 230 volts for RYB – 01 Set.
Incoming:- (a) ACB 4 pole, 415 volts with Thermal Magnetic Release (Manual Drawout type) of capacity 630 Amps.
Outgoing:- (a) MCCB 415 volts, 4 pole 200 Amps with breaking capacity 36 KA – 01 No. (b) MCCB 415 volts, 4 pole 160 Amps with breaking capacity 16 KA – 04Nos. (c) MCCB 415 volts, 4 pole 100 Amps with breaking capacity 16 KA – 02Nos.
Material and labour for painting to existing pump sets of capacity 50 HP to 100 HP with on coat of synthetic enamel paint of existing colour over a coat of red oxide primer complete all as specified and as directed.
Material and labour for painting to existing pump sets of capacity 5 HP to 20 HP with on coat of synthetic enamel paint of existing colour over a coat of red oxide primer complete all as specified and as directed.
Material and labour for Painting to existing MS pipe line of dia 80/100/150 mm with on coat of synthetic enamel paint of existing colour over a coat of red oxide primer complete all as specified and as directed.
Material and labour for painting to existing MS hose cabinet, hose reel drum with on coat of synthetic enamel paint of existing colour over a coat of red oxide primer complete all as specified and as directed.
Dismantling and taking out the existing unserviceable mono block centrifugal pump set by disconnecting the cable connection, suction and delivery pipe lines of the pump set, separate the motor from pump, transporting to workshop, removing the burnt out winding from slots, cleaning the starter and rotor slots with CTC and emery paper and rewinding the motor with as per existing size of new supper enameled copper winding wire and insulating by using class 'B' insulation keeping for drying, bring back to site, reassemble the motor and pump, fixing in position, connecting electric connections testing and commissioning for its satisfactory performance including taking down old unserviceable copper winding complete all as specified and directed for up to 20 HP capacity.
All as per Ser Item No 9 above but of 50 HP to 100 HP three phase pump set.
Dismantling and taking out the existing mono block centrifugal pump set for servicing after disconnecting / dismantling electric / suction and delivery pipe lines transporting the pump to reputed workshop remetalling to shaft, replacement of ball bearing of approved make, replacement of water seal gland and thorough servicing / check up and greasing, oiling, painting etc.reassembling the pump and motor, transporting the same to its original location, fixing in position, connecting up electrical and pipe line connection, testing and commissioning for satisfactory smooth operation including taking down old unserviceable ball bearing/small parts complete up to 20 HP three phase pump set complete all as specified and as directed.
All as per Sl Item No. 11 above but of 50 HP to 100 HP three phase pump set
Dismantling the unserviceable gland packing, supply and fixing new gland packing for replacing of worn out nut, bolt, washers of sluice valve / pump set of any size or capacity complete all as specified and as directed.
Supply and fix in replacement of Addressable Fire Alarm control panel CF-100 as per existing make complete all as specified and as directed.
Supply and fix in replacement addressable manual call point complete all as specified and as directed.
Supply and fix in replacement addressable type Hooter complete all as specified and as directed.
supply and fix in replacement of smoke / Heat detector complete all as specified and as directed.
Supply and fix in replacement of Response indicator complete all as specified and as directed.
Supply and fix in replacement 2 module box with accessories complete all as specified and as directed.
Repaire/ servicing of fire alarm panel of any make with programming the panel for serviceability and cleaning all detectors installed in any buildings / labs including testing of fire alarm system complete all as specified and as directed.
Taking down / taking up old unserviceable DI / CI / MS pipes of 150mm bore from the trench for repairs/ replacement complete all as specified and as directed.
Taking down / taking up old unserviceable DI / CI / MS pipes of 80mm bore from the trench / wall for repairs / replacement complete all as specified and as directed.
Supply and lay in replacement of MS heavy duty pipe including specials, nominal dia 150 mm dia as per IS 3589 (1981) thickness 4.8 mm complete all as specified and as directed.
Supply and fix MS flanged pipe 80mm dia heavy duty for multi storied building duly painted with two coats of synthetic enamel paint of approved tint over coat of zinc chromate primer complete all as specified and as directed.
Supply and fixing in replacement fire Gun metal hydrant landing valve (Double head outlet) of 63 mm dia conforming to IS 5290 complete all as specified and as directed.
Supply and fixing in replacement metal fire hydrant landing valve (single head outlet) of 63 mm dia conforming to IS 5290 complete all as specified and as directed.
Supply and fix in replacement of MS hose cabinet double door fabricated out of MS sheet of 18SWG CRCA sheet with glass fronted (4mm thick glass with rubber beading) door and size of the cabinet shall be 700mm x 600mm x 250mm double door mounting, all fasteners etc, and cabinet shall be powder coated of approved colour both inside and outside etc complete all as specified and as directed.
Supply and fixing in replacement of 15 mtr long,63mm dia reinforced rubber lined hose with instantaneous male and female coupling complete all as specified and as directed.
Supply and fixing of branch pipe gun metal 63mm dia instantaneous inlet, made threaded outlet, 15mm bore nozzle short complete all as specified and as directed.
Supply and fixing in replacement of 4 way fire brigade inlet with gun metal coupling complete all as specified and as directed.
Supplying, installing and commissioning of fire brigade inlet, inlet connection of 2 way with 63mm dia, built in gun metal NRV instantaneous coupling type arranged on 150/100/80 mm dia pipe mainfold and connected to wet riser mains as well as to fire water tank complete all as specified and as directed. NOTE :- Quoted rate shall included with CI butterfly valve, CI NRV and supports etc.,
Supply and fixing in replacement of Air Cushion vessel fabricated from 200mm dia pipe,1000mm height with necessary 25mm dia ball valve for drain and air / water volume control, 50 dia pressure release valve etc.,complete as per specifications supplying and fixing approved make of 200mm dia with automatic air release valve with union etc. complete all as specified and as directed.
Supply and fixing in replacement stainless-steel pressure gauges complete all as specified and as directed.
Supply and fix in repairs gun metal gate or globe valves with iron wheel head (ISI Marked), screwed both ends for iron pipe and fixed of following sizes :-
25 mm bore
40 mm bore
50 mm bore
Supply and fix Sprinkler glass blub type(Standard response) as per IS : 15106/TAC guide line 79 degree temperature rating pendent type complete all as specified and as directed.
Repairing(Minor), servicing and testing of Electric Motor Driven 50 HP to 100HP fire pump complete with pump set, electric motor, base frame and all accessories like NRV, Isolation valve, pressure switch, pressure gauges, flanged end joints, PCC foundation and foundation bolts as per specifications in duty conditions including checking of terminal box, greasing of pump set, checking of bearing, coupling ,alignment of pump set for perfect serviceability complete all as specified and as directed.
Repairing(Minor), servicing and testing of Electric Motor Driven up to 20 HP Jockey Pump complete with pump set, electric motor, base frame and all accessories like NRV, Isolation valve pressure switch, pressure gauges, flanged end joints, PCC foundation and foundation bolts as per specifications in duty conditions including checking of terminal box, greasing of pump set, checking of bearing, coupling ,alignment of pump set for perfect serviceability complete all as specified and as directed.
Supply and fix ABC powder type fire extinguisher of up to 4.5 Kgs IS : 15683 stored pressure (MAP 50) capacity , fitted with Gun metal union, high pressure discharge hose, wall mounting bracket etc. complete all as specified and as directed.
Material and labour for quarterly complete testing of fire hydrant system /fire alarm system installed in any building / any lab and also providing manpower for testing and submit the satisfactory certificate from user to Engineer- in-Charge complete all as specified and as directed.
Supply and fix in replacement of foot valve CI body flanged type of size 150mm dia heavy grade of make kirloskar or equivalent all , screwed both ends for connecting to pipeline complete all as specified and as directed.
Supply and fix in replacement of fully Automatic Star Delta Starter 50 HP, 3 Phase complete all as specified and as directed.
Supply and fix in replacement fully DOL starter, 20HP, 3 Phase complete all as specified and as directed.
Supply and fix in replacement fully DOL starter, 5 to 7.5 HP 3 Phase complete all as specified and as directed.
Supply and fix in replacement of CI, NRV 2 (PN-1.6) with required flanges nuts, bolts & gaskets etc size 150mm dia complete all as specified and as directed.
Supply and fix in replacement of CI, NRV 2 (PN-1.6) with required flanges nuts, bolts & gaskets etc size 100mm dia complete all as specified and as directed.
Supply and fixing in replacement CI butterfly valves size 100/150mm as per BS 5155 (PN 16) slim seal standard lever operated type with required flanges, nuts, bolts etc complete all as specified and as directed.
Dewatering the existing RCC UG sumps of up to 100000 litrs capacity and cleaning the internal wall and bottom surface of tank to remove silt / scales mud and other foreign materials using water and scrubbing with coir / jute/ wire brush and washing the surfaces with fresh water cleaning the surfaces with mixture of bleaching powder and water and finally washing with fresh water and treating with one coat of cement paint to internal walls bottom surfaces and ceiling of sump complete including writing on out side of the sump CLANED ON DATE and DUE ON DATE with white paint on black paint back ground on external surface of the sump at convenient height complete all as specified and as directed.
Taking out GI tubing including connection from floor wall / trenches for replacement / refixing after cleaning for the following sizes complete all as specified and as directed :-
Bore of pipe 40 & 50 mm dia.
Bore of pipe 80 mm dia.
Supply and fix GI tubing medium grade ISI marked including all fittings laid in trenches / fixed on wall of size 40mm bore complete all as specified and as directed.
Supply and fix GI tubing medium grade ISI marked including all fittings laid in trenches / fixed on wall of size 50mm bore complete all as specified and as directed.
Supply and fix GI tubing medium grade ISI marked including all fittings laid in trenches / fixed on wall of size 80mm bore complete all as specified and as directed.
Supply and fixing in repairs cast iron heavy duty sluice valve with spindle conforming to IS-14846: 2000 PN 1.6 of size 150 mm bore including suitable size nuts, bolts, washer and rubber gasket complete all as specified and as directed.
Supply and fixing in repairs cast iron heavy duty sluice valve with spindle conforming to IS-14846: 2000 PN 1.6 of size 100 mm bore including suitable size nuts, bolts, washer and rubber gasket complete all as specified and as directed.
Taking out loop of cable from sides of security light pole up to 4 mtr of length and relaying the same after removing the damaged portion of cable, supply and fixing suitable size of new aluminium lugs to all core of cable and refixing the same in box on pole etc complete all as specified and as directed. NOTE :- Excavation / returning / filling /refixing/ lugs is deemed to be including in quoted rates.
Supply and fixing in repairs cast iron heavy duty sluice valve with spindle conforming to IS-14846: 2000 PN 1.6 of size 80mm bore including suitable size nuts,bolts,washer and rubber gasket complete all as specified and as directed.
Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth in soft / loose soil for laying of GI pipes complete all as specified and as directed.
Returning, filling in trenches including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick in soft/loose soil after cables/pipes are laid and tested complete all as specified and as directed.
Removing the excavated soil to a distance n. exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and as directed.
shanti enterprises (BID ID -3438360)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .