CONSTRUCTION OF MEETING HALL AT DISTT KHAGARIA

Earth work in excavation over areas ( exceeding 30 cm in depth. 1.5 m in width as well es 10 sqm on plan) including disposal of excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth to be levelled and neatly dressed

Earth work in excavation in foundation trenches or drains(not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m . including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead.

Filling available excavated earth do - do all complet job

Extra for every additional lift of 1.5 m or part thereof in

Supplaying and filling Local Sand do - do all complet job

Providing designation 100 A one Fly ash brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level.1:3:6(1 Cement: 3 coarse sand:6 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cementcontent as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and including retard setting of concrete, improve workability without impairing strength andadmixtures in recommended proportions as per IS: 9103 to accelerate,reinforcement,durability as per direction of Engineer-incharge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.

Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cementcontent as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and including retard setting of concrete, improve workability without impairing strength andadmixtures in recommended proportions as per IS: 9103 to accelerate,reinforcement,durability as per direction of Engineer-incharge. Note:- Cement content considered in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is payable or recoverable separately.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring,shuttering,finishing and reinforcement-All work puto plinth level

Reinforcement for R.C.C. work including straightening, cutting, bending,

centring and shuttering

Providing 100A B/W with fly ash in CM (1:6) do - do all complet job

Brick work with bricks with fly ash bricks as per IS 12894(2002) & 3495 in foundation and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for Brick work in superstructure above plinth level upto floor V level

12 mm cement plaster of mix:

15 mm cement plaster on rough side of single or half brick wall of mix.

FILLING BRICK BATS IN SOAK PIT

6 mm cement plaster to ceiling of mix

12mm cement plaster to ceiling of mix :1:3(1 cement: 3 coarse sand)with floating coat of cement punning

Neat cement punning

Finishing walls with Acrylic Smooth exterior paint of required shade

Distempering with oil bound washa ble distemper of approved brand and manufacture to give an even shade .New work (two or more coats ) over and including priming coat with cement primer

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of cement primer of approved brand and manufacture on wall surface:Distemper primer

Painting with synthetic enamel paint of approved brand and manufacture to give an even shed.Two or more coats on new work

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets: 25 mm dia (heavy type)

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel prime

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance indimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness(weight not less than 12.50 kg/sqm)Fixed to steel windows by welding

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc.

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.50 mm all complete.

P/L Tactile tiles (for vision impaired person standard ) of size 300x300x9.8mm.do as per specification

P/F Oxidised M.S Double acting Spring Hinges with necessary etc(150mm)

Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S.pressed butt hinges bright finished of required size with necessery screws, all complete as per directions of Engineer-inCharge and panelling with panels of:12 mm thick prelaminated (with decorative lamination on one side and balancing lamination on other side) particle board Grade -1 medium density flat pressed, three layer and graded (FPT-1) conforming to IS :3087 bonded with BWP type synthetic resin adhesive as per IS :848 and prelamination conforming to IS :12823 Grade-1 Type II

Providing and fixing pressed steel door confirming IS code 4351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing '@ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. With fully perforated 12 mm thick micro tegular edged or 10 mm thick square edged GRG false ceiling tiles

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ),transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc.complete:

Providing and fixing aluminium hanging floor door stopper, ISInmarked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete

Applying priming coat

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy , bottle green , black of any size as approved by Engineer-in-charge in skirting , risers of steps and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete

Kota stone slab flooring over 20 mm (average ) thick base laid over and jointed with grey cement slurry mixedwith pigment to match the shade of the slab including rubbing and polishing completeBasewith1:1:1(1lime1surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse san

Extra for pre finished nosing in treads of steps of Kota stone / sand stone slab.

Extra for Kota stone / sand stone in treads of steps and risers using single up to 1.05 metre.length

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels

Providing and laying integral cement based water proofing treatment including prepatation of surface as required for treatment of roofs, balconies , terraces etc, consisting of following operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water -proofing compound cleaning the surface before treatment, (b) Laying cement concrete using broken bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar 1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix1:5 (1 cement: 5 coarse sand ) admixed with proprietary water froofing compound conforming to IS 2545 to reuired slope and treating similary the adjoining walls upto 300 mm height including rounding of junctions, or walls ad slabs. (c) After two days of proper curing applying a secoung coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement: 4 coarse sand ) admixed with proprietary water proofing compound conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300 x 300 mm square. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test, All above operations to be done in order and as directed and specifed by the Engineer-in-Charge.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing

Providing 250mm wide fly ash brick drain in cement mortar (1:6) with av. 150mm.Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqni).

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and floors wherever required :

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P Brass brackets and guard rails complete fixed with 40mm long screws, rawl plugs etc.complete.

Providing and fixing PTMT towerl rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face unplasticised -PVC molded fittings/accessories for unplasticised-PVC rain water pipes conforming to (S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for therma expansion.(SW)

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete75 mm

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete110 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot and cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including, cutting and making good the walls etc.

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end).

Providing and fixing gun metal non-return valve of approved quality (screwed end).

Providing and fixing C.P. brass bib cock of approved quality conforming to IS :8931

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS :8931

Providing and fixing 20 mm. nominal bore unplasticised PVC connection pipe with brass ions of approved brand and manufacture etc. all complete jobs.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing PTMT grating of approved quality and colour.

roviding and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work)

Constructing brick masonry chamber forunderground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe

Making soak pit 2.5m diameter 3.0 metre deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75 and S.W drain pipe 100 mm diameter, 1.8m long complete as per standard design.With F.P.S. bricks

Boring/drilling bore well of required 300 mm dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. 300mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. Dia 150mm

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully develo ped, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.150mm Dia

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:150 mm Dia

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).150 mm dia

s/f/f submersible electrical Safety wire of approved quality e/i

s/f/f submersible electrical wire of approved quality e/i

S/F/F 2 H.P Submersible pump with complete job.

Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c)M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. 1620 LPM @56 M Head

Providing and Fixing M. S. pipe as per IS:1239 ( Heavy Class ) complete with all fittings like unions, couplings, bends, elbows, tees, offsets, reducers, flanges, etc. as per requirement at site including painting with two coats of synthetic enamel paint, cutting and making good the walls complete. Pipe up to 50 mm dia. will be with threaded joints with hold tight and 65 mm dia. And above will be with welded joint. The cost shall include the MS / GI structural supports as per approved drawings and specifications.

Internal Hydrant System Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 MM Dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Gun Metal

Providing & fixing swinging type First Aid hose reel in red colour with 40 mts long and 20 mm dia heavy duty rubber water hose, 20 mm dia globe valve stop cock, terminating with G.M. coupling & nozzle of 5mm outlet with shut off valve confirming to IS 8090 - 1976 complete with drum and brackets for fixing on wall, bolts & nuts conforming to IS:884-1969 complete as required.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Gunmetal

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way - 100 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Desklet Chair Desklet Chair Size (W)520mm X (D)460mm X (H)930mm. Seat depth 500mm, Back Height 490mm mindfully designed with a removable half writing pad, that transforms it from an office chair to a stylish study nook. Wrapped in breathable premium fabric/Leatherette, the chair perches on sturdy metal legs for ensures stability. The Goods/Materials/organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD COMPLIANCE,GREEN PRO, SEFA, SEDEX, AIOTA, GRIHA & IGBC. OR

S/F/F Visitor Chair 1) SEAT/BACK ASSEMBLY: The seat and back are made up of 1.2 cm. thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. MID BACK SIZE : 47.5 cm. (W) x 58.0cm. (H) SEAT SIZE : 47.0 cm. (W) x 48.0 cm. (D) 2) POLYURETHANE FOAM: The Polyurethane foam is moulded with density = 45 +/-2 kg/m 3 and Hardness = 20 +/- 2 at 25% compression. 3) ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. 4) TUBULAR FRAME : The powder coated tubular frame is cantilever type & made of dia 25.4mm x 2mm thk M.S. ER.W. Tube. OR

Visitor Chair- Cantiliver Chair Size (Back-H-470xW-460, Seat-D-460x470)mm & Min. Height-430mm. Multipurpose fixed cantiliver chair & armrest with pading & metal base. A 14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment, posture and all day comfort. 5% post consumed recycled content & 30% total recycled content. Color-Black.The Company/Product Should having/Certified by BIFMA Membership,ISO-50001, ISO-14001, ISO-45001 from NABCB/IAF Accredited Agency also having Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, BIFMA Level-1,ZED Bronze Certificate under MSME & PEFC.

Mid Back Chair Back rest :-The outer frame of the backrest made up of injection moulded in black polypropylene and inner frame made up of injection moulded in black polypropylene. Inner frame upholstered with mesh fabric then assembled with outer frame. The back has auto contoured lumber support for achieving comfortable seating posture. Lumber support made up of injection moulded in black P.P and upholstered with U foam. Lumber support size 160mm (W) x 90mm (H) at fixed position Backrest size 650mm (H) x 530 (W). Seat :- The seat is made up of 12mm thick (7layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover made up of injection moulded in black PP to cover the plywood. Seat size 495mm (W) x 510mm (D). Minimum and maximum seat height is 450mm and 550mm respectively. Armrest :- ADJUSTABLE ARM: The armrests made up of black integral skin polyurethane with 45-55 Shore Hardness and reinforced with 4mm thick nylon insert. Arm pad size 265 x mm (L) x 95mm (W). The armrests are fitted to the seat with seat/armrest connecting strip assembly made of 30% Gas field nylon 20mm thick. rest with height adjustable up to 70mm.Minimum and Maximum height of armrest is 280mm/360mm respectively.

High Back Chair Chair Size- 76.1CM Width, 76.1CM Depth, 112.7-130.2CM Height.The Cusioned seat is made of injection molded plastic outer and inner. Plastic inner is upholstered with leatherite and moulded high resilience polyurethanefoam.The armrest top is moulded from polyurethane upholstered in leatherite and mounted onto a drop lift adjustable type tubular armrest support.The chair is 360 degree revolving type, 5 position tilt timer giving option of variable tilt angle to the chair. The pneumatic height.

2 Seater Sofa In Size 1525 X 850 X 760(WDH)mm , Frame : Plywood and klin chemical treated engineering wood. Seating cushions : 3 inches elastic webbing (350 gsm) with daigonal weave and 7 inches layered foam, (32D 23D 32D HD) WITH Ployster ployfill oiuter layer (180 gsm). Upholetry : Leatherette and Malamine finish rubber wood legs. The Company/Product Should having/Certified by BIFMA Membership,ISO-50001, ISO-14001, ISO-45001 from NABCB/IAF Accredited Agency also having Green Guard, Green PRO, Sedex,AIOTA, IGBC, AGSI,FSC, Indian Design Mark, BIFMA Level-1.

Center Table - Table Size (W) 1200mm X (D)600mm X (H)460mm. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD COMPLIANCE,GREEN PRO, SEFA, SEDEX, AIOTA, GRIHA & IGBC.

Center Table - Table Size (W) 600mm X (D)600mm X (H)460mm. The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD COMPLIANCE,GREEN PRO, SEFA, SEDEX, AIOTA, GRIHA & IGBC.

Dias Table - Table Size (L) 6000mm X (W) 750/900mm X (H) 900/1050 mm. (Seating Capacity minimum for 8 Person) Top should be in glossy finish.The Materials/Organization shall be certified ISO-9001, ISO-14001, ISO-50001, ISO-45001, all ISO Certificates should be Issued from NABCB Accelerated Agency, BIFMA LEVEL 1, BIFMA Membership and BIFMA Compliant product base , Indian Design Mark certified, Trade Mark Certified, GREEN GUARD COMPLIANCE,GREEN PRO, SEFA, SEDEX, AIOTA, GRIHA & IGBC.

Estimate for Provision of Electrical Wiring & Electrical Installation in the proposed meeting hall for Khagaria Collectorate, Distt. Khagaria.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.I. box etc as required.

Wiring for group controlled (looped) light point/ fan point/ exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit etc as required.

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 nos. 5 pin 5/6 amps modular socket outlet and 2 nos. 5/6 amps modular switch, connection etc. as required.

Wiring for circuit/submain wiring along with earth wire with the following size of FRLS PVC insulated copper conducter SC cable in surface / recessed medium class PVC conduit as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed PVC conduit as required

Supplying and fixing 2 pin, 6 amps ceiling rose on the existing junction box / wooden block including connection etc as required.

Supplying and fixing batten/angle holder including connection etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 amps modular socket outlet and 25 amp modular SP MCB 'C' curve, including connections, painting etc. as required.

Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus-bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus -bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supptying and fixing following rating, 24Al4L5 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep with service value (CM/MM) minimum 4.00, Air delivery minimum 270 cum/min including wiring the down rods of standard length (upto 30cm) with 1.5 sq. mm FRLS PVC insulated copper conductor etc as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/ switch box including connections but excluding modular plate etc. as required.

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

Supply and installation of 400 mm, 230 V A.C. wall/cabin fan including fixing the bracket, making connection, testing, commissioning etc as required.

Supplying and fixing recess mounted following types LED downlighter with minimum efficacy 100 lm/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing 4'X20 watt LED batten with minimum efficacy 100 lm/w in aluminium housing and complete with integrated electronic driver etc directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required. (For Non-residential building)

Supplying and fixing recess mounted 36 watt LED flat panel (2' X 2') with minimum efficacy 100 lm/w which privides soft light and glare free symmetrical illumination suitable for armstrong/grid ceiling and integrated electronic driver etc directly on false ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

Supplying and fixing electronic musical call suitable for single phase, 230 volts complete bell as required.

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supplying and fixing of 32 mm dia X 1.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV/ HPSV/ LED street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required.

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.)

S/F copper Strip 50 mm X 5 mm sizes for bus-bar including interconnection etc. as reqd.

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as reqd.

Providing and fixing following capacity four pole ON-load panel mounted changeover switches inside the existing cubical panel board including drilling holes in cubicle panel, making connections etc. as required.

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Providing and fixing lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Jointing copper/ G.I. tape ( with another copper/ G I tape, base of the finial or any other metallic object ) by riverting/ nut bolting sweating and soldering etc. as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. ( For vertical run)

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coke and salt as required.

Supplying and laying 25 mm X 6 mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ termination with GI nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box along with modular base and cover plate for modular switches in recess etc as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and drawing following pair 0.5 sq. mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supply and erection of 6 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 6A 'C' series SP MCB, connector, and suitable size foundation bolts with template as required.(but without pole foundation)

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Providing and making steel pole collar with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 stone aggregate 20 mm ) of specified size and shapeincluding form work, plastering if required, curing etc. as required. (volume of pole/pipe not to be deducted)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required but excluding sand cushioning and protective covering.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

Supplying and fixing post top / gate light (width 250/300 mm) made up of high grade unbreakable polycarbonate material suitable for upto 20 watt LED lamp including connections and earthing the body etc as required. ( But without lamp)

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

Supply, installation, testing, commissioning, and final testing of automatic lift complete in the shaft well and pit already constructed as per CPWD specification including automatic rescue device (ARD), All standard equipments, accessories and control equipments as per manufacturer's design and as per CPWD specification (Part III LIFTS) on turnkey basis, Conforming to NBC/statutory norms and fulfilling following requirements.(Make- Otis, Kone, Schindler, Mitshubishi, Johnson/Thyssen Krupp)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit with modular switch , modular plate, suitable size G.I. box etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. As reqd.

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

Supplying and fixing 10/12 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,IP 65 protection and complete with integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Fixing for laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

P/F/F sheet metal main switch disconnector fuse unit in existing metal board with rewirable type fuses, including drilling holes in metal board, making connection as reqd.

P/F/F bus bar chamber with 4 strips of suitable size made of copper heavy duty complete with all accessoires including connection earthing the body etc.as reqd.

Providing chemical/ mineral maintenance free aerthing system comprising of copper earth electrode 3 metre length and 17.2 mm outer dia along with 25 Kg earth electrode conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth inspection pit etc. as required.

P/F/F bus bar chamber with 4 strips of suitable size made of copper heavy duty complete with all accessoires including connection earthing the body etc.as reqd.

Providing chemical/ mineral maintenance free aerthing system comprising of copper earth electrode 3 metre length and 17.2 mm outer dia along with 25 Kg earth electrode conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth inspection pit etc. as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus-bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

Supplying, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condensor fan shall be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 °C. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 6.4, Capacity > 40 and <70 ISEER 6.5, Capacity > 70 ISEER 6.6 for ECSBC+ Building) For Cooling or Heating or Both

Supplying, Installation, Testing and Commissioning of following minimum capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement in auto mode. The cooling capacity of indoor unit will be at air inlet conditions of 27 0C DB and 19 0C WB temperature. (Make will be same as of Outdoor)

Supplying, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and comfort washable synthetic media pre- filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 0C DB and 19 0C WB temperature. (Make will be same as of Outdoor)

Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature). Inverter Type - Cooling only

Supply installation testing and commissioning of Atomatic Voltage Stabilizer of Capacity 4 KVA, input voltage -130V± 10% and output-220 V ± 10% of Capacity & input Range 130V to 280V Model (For 1.5 Ton AC)

Supplying, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs

Supplying, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required

Drain piping :- Providing and fixing of CPVC, 6Kg/cm2 drain water piping with fittings, support and insulated with 6 mm thick closed cell elastomeric nitrile rubber insulation complete as per specification.

Control cable: Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

Refrigerant:- Supply and additional refrigerant charge of refrigerant R410/410A & equivalent Eco friendly green gas to compensate the additional piping done at site for all systems including testing commissioning as required

Suppiying,Design,fabrication and fixing of MS foundation is made of MS Channel of Size 100 x 50 x 50 x 6 mm thick with beady of hollow square pipe 25 mm x 25 mm x 3 mm thick (approx 48 Kg) and Paw of MS Plate of Size 30 Cm x 30 Cm x 10 mm (approx 9 kg).Additionally rubber paddin,g is provided between vrf outdoor unit and MS channel.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.

Supply and fixing fabricated Feeder pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator, with 40mm X 40mm X 5mm angle iron stand and complete in all respect etc and must be CPRI approved panel manufactures. (But without RYB LED lamp, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears, PCC work etc.)

S/F copper Strip 50 mm X 5 mm sizes for bus-bar including interconnection etc. as reqd.

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as reqd.

Supplying and fixing following way, horizontal type three pole & neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus -bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supptying and fixing following rating, 24Al4L5 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit as required.

Supply of following sizes and core PVC/XLPE insulated, PVC sheathed (heavy duty) armoured electrical power cable with aluminium conductor for working voltage upto 1.1 KV as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Above 35 sq. mm and upto 95 sq. mm (Clamped with 25 x 3 mm MS flat clamp)

SITC 2MP @ 25/30fps@1080P (1920×1080) Dome Camera with 2.7 mm fixed lens. 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, Color: 0.01 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, DWDR, 3D Digital Noise Reduction, Tripple individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, IK10, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection, video tampering, UL, CE, FCC certified. (Approved Makes: Hikvision/CP Plus/Honeywell)

SITC 2MP @ 25/30fps@1080P (1920×1080) Bullet Camera with 2.7 mm fixed lens. 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, Color: 0.01 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, DWDR, 3D Digital Noise Reduction, Tripple individually configurable stream, 12 VDC & PoE, IR range: 40m, IP67, IK10, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection, video tampering, UL, CE, FCC certified. (Approved Makes: Hikvision/CP Plus/Honeywell)

SITC of 16 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16, 2nd screen: 1/4/8/9/16 - Connect Up to 16 IP Cameras, Dual OS, Up to 12 Megapixels Resolution, Two independent HDMI outputs, one HDMI output of 4K resolution,1 VGA output with output upto 1920 × 1080, Support H.265, MJPEG, Supports N+1 hot spare system,Supports RAID0, RAID1, RAID5, RAID6 and RAID10 ,Supports HDD hot swap, Supports Dual Power-Redundant, Incoming Bandwidth 320 Mbps, 8 SATA Hard Disks, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD upto 6TB, 3 × USB at least 1 × USB with 3.0, Alarm I/O 16/4, RS-485, RS-232, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified. (Approved Makes: Hikvision/CP Plus/Honeywell)

SITC of 4TB Surveillance Hard Disk Custom-built for surveillance applications with Image Perfect firmware for crisp, clear, 24×7 video workloads Maximum 180TB/year workload rating—3× the workload rating of desktop drives—for reliable performance in write-intensive surveillance systems Rotational vibration (RV) sensors help maintain performance in RAID and multi-drive systems (4TB or higher) Up to 10TB of capacity to store up to 10,000 hours of HD video (Approved Makes: Seagate/WD/Toshiba)

SITC of 16 port PoE Layer 2 Network Switch with PoESupport of 270W or higher with each cooper portsupporting 802.3at PoE+ min. Fixed-configuration 1RU x 1/2, half-rack width chassis16 x RJ45 10/100/1000 BaseT PoE+ ports2 x SFP/RJ45 combo ports2 x SFP ports1 x USB port (type A, USB 2.0)1 x Console port (RS232 RJ45)IEEE 1588v2 capable ports 12MACsec capable ports 12Switch capacity 24 Gb/sPoE power budget 115WIncludes power cord & manuals/software access cardsIncludes RJ45 to DB9 adaptorOperating temperature: -10°C to 60°C (14°F to 140°F) Storage temperature -40°C to 85°C (-40°F to 185°F) (Approved Makes: Cisco/Alcatel/HP/Dlink)

Supplying, Installation, Testing and Commissioning of32 INCH LED display (LED monitor) industrialgrade with 3840x2160 resolution or better, USBplayback, bluetooth and miracast connectivity, 4XHDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nits309 DELHI SCHEDULE OF RATES (E&M)-2025or better, Video wall mode should be available,contrast ratio: 1200:1, OPS slot, viewing angle (H/V):170°/ 170°, response time less than 12ms, Displaycontrol shall be on monitor screen and programmablewith remote (remote shall be supplied with system),Key Board, Optical Mouse, etc. as required. MAKE - PANASONIC/SONY/SAMSUNG

Supplying, drawing, Testing and commissioning ofCat6A UTP 4 pair, 23 AWG solid copper cable inexisting conduit/ on surface, U/FTP, LSZH, Non-Plenum, Horizontal (solid) Cable suitable for highspeed data networking application supporting upto10Gbps over a 100 meter channel. The 4 UnshieldedTwisted Pairs (UTP) cable with color coded insulationfor easy indentification should have FLAMEPROPERTIES i.e. Flammability Test - IEC 60332-1,Smoke Density - IEC 61034, LSZH standardscompliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE802.3an, RoHS. Delay Skew should be < 45NS. Theouter Cable Diameter should be 7.5 + 2 mm. Cableshould have been tested and verified by UL/ ETL etc.complete as required. (Make - Legrand/Dlink/Belden)

Supplying and fixing of 4U Wall MountRack having Fixed Structure with 0.8mm CRCASheet, completely knocked-down condition (CKD)Shape, Vertical Mounting Rail 1.6 mm with 'U'Marking,Minimum 2 cable entry/exit provision at Top andbottom with rubber protection, Front 5mm ToughenedGlass with lock, wall mounting kit WITH ACCESSARIES Approved Makes: Poweride/MTS/Rittal/APC/APW

SITC of 5 mtrs length HDMI Cable. Make- Honeywell/Kramer/Aten

SITC of RJ45 Connector . Make - Dlinl/Legrand/Eqv.

SITC of Extension Board. Make - Finolex/Anchor/Eqv.

SITC of Junction Box 5x5. Make - Finolex/Anchor/Eqv.

Supplying and fixing of following sizes of mediumclass PVC conduit along with accessories insurface/recess including cutting the wall and makinggood the same in case of recessed conduit asrequired. 25 mm. Make - Finolex/Anchor/Eqv.

Supplying, drawing, Testing and commissioning ofCat6A UTP 4 pair, 23 AWG solid copper cable inexisting conduit/ on surface, U/FTP, LSZH, Non-Plenum, Horizontal (solid) Cable suitable for highspeed data networking application supporting upto10Gbps over a 100 meter channel. The 4 UnshieldedTwisted Pairs (UTP) cable with color coded insulationfor easy indentification should have FLAMEPROPERTIES i.e. Flammability Test - IEC 60332-1,Smoke Density - IEC 61034, LSZH standardscompliance: ANSI/TIA-568 C.2, ISO/IEC 11801, IEEE802.3an, RoHS. Delay Skew should be < 45NS. Theouter Cable Diameter should be 7.5 + 2 mm. Cableshould have been tested and verified by UL/ ETL etc.complete as required. (Make - Legrand/Dlink/Belden)

Supply , Installation , Testing and Commissioning of 12 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts. Approved Makes: Poweride/MTS/Rittal/APC/Legrand

SITC of 24 port PoE Layer 2 Network Switch with PoE Support of 370W or higher with each copper port supporting 802.3at PoE+ min.

SITC of WIFI Access Point Supplying, Installation, Testing and commissioning of indoor Wireless Access Point for High density use having features and specifications etc. as mentioned here under- WiFi6 802.11ax 574Mbps (2.4GHz) + 2402Mbps (5GHz), WIFI 6 Certified, 1 x RJ45 console port, MG 2.5G LAN POE Port, factory reset, WPA/WPA2/WPA3™ Personal/Enterprise, WEP 64/128-bit, SSID broadcast disable, MAC address access control, Internal RADIUS server, SNMP, Customizable Captive Portal, Auto Channel, Works as Access Point, WDS, WDS with AP, Wireless Client ., Web (HTTP), Secure Socket Layer (SSL), Traffic control, Support ATF/Fast Roaming/Band Steering, Supports enhanced security – WPA-PSK/WPA2 PSK/WPA3-PSK and RADIUS client, and Cipher negotiation, and MAC/ IP ACL for networks, Certifications: MTCTE, CE, FCC. Works as Standalone, Compatible with S/W & H/W Controller with addtional features like - Real-Time. Make - Dlink/ Cisco/ Alcatel

SITC of Wireless Controller Wireless & Radio PerformanceWi-Fi Generation: Wi-Fi 6 (IEEE 802.11ax), backward compatible with 802.11a/b/g/n/ac.Concurrent Band Speed: Combined throughput up to 1800 Mbps (AX1800).5 GHz Band: Up to 1200 Mbps.2.4 GHz Band: Up to 574 Mbps. Antenna Setup: 2 x dual-band internal omnidirectional antennas.Antenna Gain: 3.2 dBi at 2.4 GHz / 4.3 dBi at 5 GHz.Signal Optimization: Integrated MU-MIMO (2x2), Beamforming, Band Steering, and Airtime Fairness.Interface & PowerEthernet LAN Port: 1 x Gigabit RJ45 port supporting PoE input.Console Interface: 1 x RJ45 Console management port.Power Supply Options:PoE: IEEE 802.3at Power over Ethernet (Power consumption up to 16 Watts). Make - Dlink/Cisco/Alcatel

Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required. Copper Patch Cords of length 1m (3ft) . Make - Dlink/Comscope/Belden

Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc. complete as required. Copper Patch Cords of length 3m (10ft) Make - Dlink/Comscope/Belden

Supplying, Installation, Testing and commissioning of CAT6A Copper Information Outlet (IO) with face plate of color as per site requirement, should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and Components should be from same OEM to maintain compatibility and interoperability etc. complete as required. Make - Dlink/Comscope/Belden

24 port Cat6A Patch Panel loaded. Must be of 1U height with clear label holders and white label with the panel. 24 Ports Cat-6 Patch Panel should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D following CAT6 Patch Cord should have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D . Make - Dlink/Comscope/Belden

SITC of wired Table Top Microphone a highly reliable, plug-and-play digital discussion system ideal for boardrooms, courtrooms, and local councils. Key System FeaturesPlug-and-Play Setup: Easily connect up to 80 discussion devices directly to a single Control Unit, scalable up to 245 units using extension units.Audio Recording: Records up to 4,000 hours of discussion using a standard USB stick (up to 128 GB) via the built-in MP3 recorder.Feedback Suppression: Utilizes DAFS technology to prevent howling and ensure superior speech intelligibility. Approved Makes: Sennheiser, Clock Audio, Bosch

SITC of 2-way Cabinet Loudspeaker, LF Driver 5.25” & HF Driver 1" Max Power Handling 100W @ 8 Ohms ; Multiple 100V Taps : 40W/20W/10W; Frequency range 55Hz – 20Khz or better ; Sensitivity 87 dB or better and Max SPL 104 dB or better; Coverage of 100° x 100° (H X V) or better; IP40 Rated; ABS Plastic Housing with steel grill. Mounting Bracket Included. Approved Makes: Audac, Yamaha, Bosch

SITC of Quad Channel Energy Star Rated Class D Amplifier , 4 X 250W @ 4Ω or better, Frequency Response (± 3 dB) 20 Hz - 20 kHz ,Signal / Noise > 90 dB or better, Active Crossover, Protection Circuit : DC, Overheating, Overload, Signal limiting, XLR Line Inputs , 2-Pin Terminal Outputs , 1U 19" Rackmountable. Approved Makes: Audac, Yamaha, Bosch

SITC of Dual Channel Energy Star Rated Class D Amplifier , 2 X 150W @ 4Ω, 2 X 80W @ 8Ω, 1 X 300W @ 8Ω Bridge or better, Protection Circuit : DC, Overheating, Overload, Signal limiting, XLR Line Inputs , 2-Pin Terminal Outputs , 1U 19" Rackmountable. Approved Makes: Audac, Extron, Bosch

SITC of 1:8 HDMI Distribution Amplifier w/4K60 4:4:4. Splits one HDMI source to eight outputs. Should be handles Dolby TrueHD, Dolby Atmos️, DTS HD, DTS:X️, and uncompressed 7.1 linear PCM audio. EDID management options . Approved Makes: Extron, Crestron ,AMX

SITC of Transmitter for HDMI, RS 232, and IR Signal extension up-to 40m. Should support video signals HDR10+, Dolby Vision, Deep Color and 4096x2160 @60 4:4:4 resolution. Should support audio signals Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS-ES, DTS HD High Res, DTS-HD Master Audio & LPCM up to 8 channels. Should support HDCP 2.3 content protection. Should have 1x HDMI Input, 1x RJ45 output, 1x RS-232 & 1xIR.Should pass EDID and CEC. Should comply to CE, IC, FCC. Approved Makes: Extron, Crestron ,AMX

SITC of 65inch Display with resolution 3840 X 2160 (UHD) ,Brightness 400nits or better ,Dynamic Contrast Ratio 1,000,000:1 , Static (Panel) Contrast Ratio 1200:1 or better , Inbuilt speakers 10W +10W or better , Approved Make : LG ,Panasonic ,Sony

SITC of 75inch Interactive Pannel Display with resolution 4K Ultra HD ,Refresh Rate 60Hz or better ,in built Wifi , Bluetootth with 20Watt inbuilt speaker output ,Operating System (OS) webOS 25 Approved Make : LG,Sony , Panasonic

Supply, Installation, Testing & Commissioning of AI based Full HD 1080p @ 60fps Presenter PTZ Tracking Camera with Dual Camera- one PTZ Camera for Presenter Tracking and second fixed lens Panoramic Camera. PTZ Presenter Camera should support min 30X Optical Zoom and 8x Digital Zoom with Panning range of +170 deg to - 170 deg and Tilt Range of -30 to +90 Degrees, Field of View for PTZ Camera should be min 58 Degree or more with CMOS Sensor 1/1.8" , camera should support simultaneous outputs through HDMI, 3G-SDI, USB 3.0 and IP with 1x Audio In and can be controlled via RS232 and IP. Should support multiple video streams. Tracking Camera should support Everywhere Tracking, Partition Tracking, Auto framing Should support PoE and Virtual USB Driver. Quoted model should be BIS, CE, FCC , Clickshare & RoHS Certified with Test Lab Reports. Approved Make: Lumens ,Sony ,Vaddio

SITC of AVoIP Decoder supporting 4K @60fps with simultaneous outputs through HDMI 2.0, USB Type C & USB Type A with Line Out & 3.5 mm, 1x Line In & 3.5 mm. The decoder should be capable to convert IP to USB 3.0 & HDMI. The decoder should support Video Decoding Formats of H.264/HEVC with in-built AES128 encryption and NDI HX3 / NDI HX2 / RTSP, PoE+ Approved Make : Crestron, AMX, Lumens

SITC Of Audio Cable

SITC of 27U AV Rack

SITC of XLR Connector

SITC of 2core 0.75sq mm Speaker cable

SITC of Cat6 Cable

SITC of 15M HDMI cable. Make - Kramer/Honeywell/Extron

Electric Building Division, Bhagalpur

Building Construction Department.