SPL REPAIR TO EXTERNAL ELECTRIFICATION OF ADV SIG DET AT BASE CAMP AND ROCKFALL SIG DET AND SPL REPAIR (E/M) TO TXN NETWORK AT NEW BDE KLP UNDER GE 873 EWS

Amount

M&L plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundation of stay assembly etc including necessary form work complete all as specified.

S&F double wall corrugated (DWC) outer pipe 63 mm and inner dia 50 mm fix complete to wall, poles etc laid in trench with cable etc with suitable clamp for protection of cable complete all as specified and directed by Engineer-in-charge.

S&F double wall corrugated (DWC) outer pipe 40 mm and inner dia 32 mm fix complete to wall, poles etc laid in trench with cable etc with suitable clamp for protection of cable complete all as specified and directed by Engineer-in-charge.

S&F double wall corrugated (DWC) outer pipe 50 mm and inner dia 38 mm fix complete to wall, poles etc laid in trench with cable etc with suitable clamp for protection of cable complete all as specified and directed by Engineer-in-charge.

M&L for PCC 1:2:4 type B1 (20mm graded agg) 100mm thick in foundations, filling and mass concrete complete all as specified and directed by the Engineer–in–Charge.

S&F light grade 80mm GI pipe fix complete to wall, poles etc with suitable clamp for protecton of cable complete all as directed.

S&F light grade 40mm GI pipe fix complete to wall, poles etc with suitable clamp for protecton of cable complete all as directed.

Supply and laying GI pipe medium grade 40mm fixed on walls/poles /laid in trenches as cable protection complete all as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dence soil complete all as specified.

Excavating in trenches, exc 1.5 m wide and n exc 3.00 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 3.00 m in depth and getting out in hard/dence soil complete all as specified.

M&L Returing, filling in incl spreading, levelling watering and well remming in layers n.exc 25cm width, Complete all as specified and directed.

M&L for Removing excavated materialn. exc 50m and depositing where directed at a level n exc. 1.5m above the starting point Complete all as specified and directed.

unwashed Sand cushioning to under ground cable provided with a layer of 8 cm deep before laying and 15 cm covering above the top edge of cable after laying complete all as specified. Note : maesurement shall be done after puning down of sand.

M&L unreinforced precast factory made concreate cable cover class LV type-I with flat size 250X150x40mm complete all as specified and directed.

Supply, laying, fixing, passing through pipe or laid in trenches and testing underground XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross section area 25 sqmm 4 core complete all as specified and directed by Engineer-in-charge.

Supply, laying,fixing, passing through pipe or laid in trenches and testing underground XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross section area 3.5 core 35 sqmm all as specified and directed by Engineer-in-charge.

Supply, laying,fixing, passing through pipe or laid in trenches and testing underground XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross section area 3.5 core 25 sqmm all as specified and directed by Engineer-in-charge.

Taking up the existing cables from trenches of any size all as specified and directed.

Supply, laying and cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core complete all as specified and directed. NOTE: The cable must be FRLS.

Supply, laying and cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and directed. NOTE: The cable must be FRLS.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3.5 core complete all as specified and directed NOTE: The cable must be FRLS.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core complete all as specified and directed NOTE: The cable must be FRLS.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sq mm 3.5 core complete all as specified and directed NOTE: The cable must be FRLS.

Supply, installation, testing and commissioning LT panel, factory made dust and vermin proof, double door type with provison of gasket in each compartment, provision of mounting hooks, each compartment should not be less that 350 mm x 350mm, outdoor type made out of 3.15 mm thick CRCA sheet of size 1.5m x 1.5m x 0.6m including seperate compartment for each MCCB & for cable and busbar, mounted on frame of MS angle iron 45mmx45mmx6 mm with front and back openable door with lock & Key including necessary grouting and double coat powder coated of grey colour painting complete with following accessories.PCC shall be deemed to be included in the rates, 150 mm of the MS angle legs shall be unde the ground, supported with 1'x1x1' PCC on each leg of LT panel. The drwgs of LT panel shall be approved from the accepting officer. The degree of protection and Aluminium bus bar chamber (4 Strips) (40mm x10mm) 3 phase 415 volts 300 Amps all as required panel shall be IP-54 including foundation all as specified and directed.

Supply, installation, testing and commissioning LT panel, factory made dust and vermin proof, double door type with provison of gasket in each compartment, provision of mounting hooks, each compartment should not be less that 350 mm x 350mm, outdoor type made out of 3.15 mm thick CRCA sheet of size 1.5m x 1.2m x 0.6m including seperate compartment for each MCCB & for cable and busbar, mounted on frame of MS angle iron 45mmx45mmx6 mm with front and back openable door with lock & Key including necessary grouting and double coat powder coated of grey colour painting complete with following accessories.PCC shall be deemed to be included in the rates, 150 mm of the MS angle legs shall be unde the ground, supported with 1'x1x1' PCC on each leg of LT panel. The drwgs of LT panel shall be approved from the accepting officer. The degree of protection and Aluminium bus bar chamber (4 Strips) (40mm x10mm) 3 phase 415 volts 300 Amps all as required panel shall be IP-54 including foundation all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600mm x600 mm x 6mm buried directly in ground vertically to a depth not less then 2.25 meter below normal ground level with top edge of the plate not less then 1.50 meter below normal ground level connected to galvanized earth wire 4.00mmdia by means of bolts ,nuts ,check nuts and washers complete up to and including test point made out of 40 x 6mm alum flat including earthing pit , charcoal common salt ,Earthing lead 4.00mm dia up to 7.5m, 20mm dia medium grade GI watering pipe ,G.I. protection pipe 15 mm dia up to 7.5m long,,PPC pit in PCC 1:2:4 type B-1 using 20 mm graded stone aggregate ,PCC pit cover including earth work complete all as shown in electrical plate No-5 of SSR-1991 (part-I)

Supply and install steel, tubular swaged poles complete with cast iron base plate, nuts and taper plug , bolts, nuts and screws as specified type 410-SP- 31 (9.0 m long).

Supply and fixing LED street light fitting 35 Watt230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistantcomplete with driver, lamp bracket with impac and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

1M & L for bracket made out of GI tubing 40mm dia,light grade 1.5 mtr long including fixing with MS clamps -2 Nos made out of 50 mm wide 5mm thick flat iron with M.S nuts bolts 75 mm long 12 mm dia -4 Nos with flat washer (3mm thick) -02 No for each including painting with aluminium paint over one coat of red oxide to the M.S clamps & bracket etc complete.

Supply, fix test and commissioning of all in one solalr street light made with high efficiency Mono Crystalline solar PV Module, Lithium Ferro Phosphate battery with in-built BMS technology, High efficacy LED, MPPT Solar charge controller and Aluminium extruded body & is specially programmed to automatically control the dimming and brightness of light, which increases the back up time. including pole with adquate PCC depth complete all as specified and directed at site.

Supply & Install, testing & commissioning of 15 mtr high mast lighting system with all accessories, Mast shall be in 3 sections, hot dip galvanised and suitable for wind velocity as per IS 875 part 3. It shall also include accessories for high mast including all side lights suitable for area lighting, stainless sttel wire 6 mm dia rope, integrated motor, connector, manual handl,e lighitening finia, construction, double drum winch, Galanised Lantern carriage arrangements suitable for 12 luminaries symmetrically & its control ger boxes and lightning finial. The mast shall have an integral power tool installed inside the base compartment for its motorised operation also manual operation complete all as directed inclusion of following points :-

Items No 35 Contd/- (a) M&L for HIgh mast light foundation/bedding with PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as per manufacturing instructions complete. (b) S&F for foundation bolts manufactured from special steel along with nuts, washer, anchor plate and templates. (c)S&F for LED type single dome aviation obstruction light-01 No and including all connected wiring complete. Make :Bajaj/Crompton or equivalent. (d) M&L for foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc. basement slabs under-reamed piles and mass concrete M20 grade using crushed stone aggregate complete, shall be as per manufacutre recommendations. (e) M&L for Formwork to sides of concrte foundations, footings, bases of columns, raft and raft beams , sides soffits (if any of foundation and plinth beams; and similar work; verticle or to batter complete. (f) S&F outdooe stand mounted feeder pillar box 3.15mm thick CRCA sheet, CPRI approved with 32 A TPN MCB incomer single dial time switch, 25 A TP contactor for automatic switching of luminaries, power tool control with2 Nos 9A contactors and raise lower push button, incoming 35 Sqmm and out going 16 & 2.5 Sqmm terminals. (g) S&F LED flood light 200 Watt -12 Nos including all accessories and silicon filled ported driver, IP-66 protection, driver must have BIS regisration. (h) Trailing cble PVC armoured type from luminaries to the base of pole and from base to feeder pillar box. (j) Provision of lighting finial on the top of the pole. (k) 2 x Earthings,1 x for LT panel, 1 x for lightening final shall be included with 25mm x4mm GI Strip. (l) All above items are included in the rates. No extra amount will be paid seperately.

Supply & fix PVC sintex Junction box of size 280 X 170 X 130 mm Cat No GS-JB-2817 Hinged (L) wiith 2 way connector mounted on epoxy insulators for looping of cable for 1Phase and 1neutral fixed on pole with the help of MS nuts bolts and MS clamps-2 Nos of size 40 mm X 4 mm thick with one No MCB SP 6 Amp capacity mounted on din rail inside box. work also includes making suitable hole in pole to take out connections to fitting if required at site and provisioning of 1.0 sqmm 3.0 core flexible PVC insulated copper cable from junction box to conector of street light Complete all as specified and directed.

S&F pin type, pocelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 150mm height, 150mm dia for 1100 volts grade Complete all as specified and directed.

M&L for aluminium conductor steel reinforced (ACSR) on pole stringing properly on insulators and binding with aluminium binding wire, jumper set complete for any size (Ferret, Wessal, Squirel) of conductor complete all as specified and as direcetd by the Engineer-in-Charge.(NOTE:- Measurement and payment shall be made by measuring horizontal distance between centre of two adjustant poles and adding 3% extra for sag, joints and jumpers etc) Complete all as specified and directed.

Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique & necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 Mpa working pressure Complete all as specified and directed.

Supply, fabricating , fixing structural mild steel channel angle iron, flat iron and brackets etc for fabrications of cross arms, bracings, supports, D-clamps, stiffeners, eye hooks, bolts, pole clamps and back plates including nuts, bolts and washers, welding banding cold , or hot drilling holes for insulators bolts in any shape or size as indicated or directed and inclusive of one red oxide primer coat ,one under coat and one finishing coat of aluminium paint complete.(Insulators to be measured and paid for separately) Complete all as specified and directed.

Supply and fix galvanised stay strand wire 7/4mm suitable for staying of poles etc.

MM&L for Earthing complete with galvanized steel earth plate electrode 600x600x60mm thickness not less than 6mm thick buried directly in ground( earth plate not less than 2.25 mtr deep below normal ground level) with top edge of earth plate not less than 2.5 mtr below the normal ground level connected to galvanized iron earth strip of size 32 x 6 mm thick by means of nuts bolts, nuts, check nuts and washers of GI steel all as shown in electrc plate No. 3 connected to earth test point all as specified and indicated complete and including charcoal dust,salt etc and GI protection pipe light grade 40mm bore and GI watering pipe 20mm bore medium grade with funnel and wire mesh ,40mm thick pre cast RCC M-15 ( Nominal mix) cover reinforced with XPM weight not less than 4 Kg/Sqm with suitable handle of 6mm dia MS bar and angle iron 40X40X3mm frame for cover, PCC M-15 ( Nminal mix) pit, excavation and earth work in any type of soil and connected all as specified and as directed.

Supply, Install Testing & Commissioning of self supporting totally enclosed double door at front, LT feeder piller compartmentalised design, dust and varmin proof of size 1200 mm (Height) x 1000 mm (Length) x 800 mm (Width) suitable for 440 Volt 3 phase 4 wire system made out of 3.15 mm thick CRCA sheet and built upon regid frame work having front and rear hinged doors with neoprence rubber gasket including danger plate, earthing strip point and, ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts ;and washers etc. The pannel shall be synthetic enamelled painted and the control circuit diagram shall be with colour code solid conductor copper 1.5 sqmm cable for easy identification including incomming/outgoing cable holes at the bottom, complete after taking down the old unserviceable one. The Panel shall be emmbeded with 50x50x60mm MS Angle Iron frame and to be grouted with PCC foundation (1:2:4) type B2 upto a height of 50 cm from normal ground level and above 80cm a height from normal ground level of complete all as specified, directed and comprising of the following.

Items No 45 Contd/- Including (a) Copper bus bar 200 amps - 04 Nos, Incoming (b) Supply and fix 4 pole MCCB 250 Amp, 50 Hz, 415V with rupturing capacity 35/36 KV-01 No (c) RYB neon indicating lamp set of three-01 Outgoing (d) Supply and fix 3 pole MCCB 125 Amp, 50 Hz, 415V with rupturing capacity 18 KV-01 No (d) Supply and fix 3 pole MCCB 63 Amp, 50 Hz, 415V with rupturing capacity 18 KV-03 No (e) Lock pedestal- 01 No Note: Rates are deemed to be inclusive of PCC platform of suitable size and 45cm height and 4 Nos legs of 50mmx50mmx6mm and 60cm in hieght for fixing the panel. Danger notice plate (02 Nos) Lt size 20cmx15cm shall be fixed on the panel. Contractor provided power coated finish paint on panel. Contractor have to provide panel drawing before suppling panel at ground.

Supply, Install Testing & Commissioning of self supporting totally enclosed double door at front, LT feeder piller compartmentalised design, dust and varmin proof of size 1000 mm (Height) x 800 mm (Length) x 600 mm (Width) suitable for 440 Volt 3 phase 4 wire system made out of 3.15 mm thick CRCA sheet and built upon regid frame work having front and rear hinged doors with neoprence rubber gasket including danger plate, earthing strip point and, ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts ;and washers etc. The pannel shall be synthetic enamelled painted and the control circuit diagram shall be with colour code solid conductor copper 1.5 sqmm cable for easy identification including incomming/outgoing cable holes at the bottom, complete after taking down the old unserviceable one. The Panel shall be emmbeded with 50x50x60mm MS Angle Iron frame and to be grouted with PCC foundation (1:2:4) type B2 upto a height of 50 cm from normal ground level and above 80cm a height from normal ground level of complete all as specified, directed and comprising of the following.

Items No 46 Contd/- Including (a) Copper bus bar 250 amps - 04 Nos, Incoming (b) S&F Onload change over switch 415V in Sheet metal with front handle enclosures 4 pole of capacity 250Amps= 1 Nos (c) Supply and fixx 4 pole MCCB 150 Amp, 50 Hz, 415V with rupturing capacity 35/36 KV-01 No (d) RYB neon indicating lamp set of three-01 Outgoing (e) Supply and fix 4 pole MCCB 63 Amp, 50 Hz, 415V with rupturing capacity 18 KV-04 No (f) Lock pedestal- 01 No Note: Rates are deemed to be inclusive of PCC platform of suitable size and 45cm height and 4 Nos legs of 50mmx50mmx6mm and 60cm in hieght for fixing the panel. Danger notice plate (02 Nos) Lt size 20cmx15cm shall be fixed on the panel. Contractor provided power coated finish paint on panel. Contractor have to provide panel drawing before suppling panel at ground.

S&F LT cable route direction metal sign board, yellow color circular plate with written indication and fixing arrangement on earth all as directed and specified.

S&F ON LOAD change over switch 415 V in sheet metal enclosures 4 pole of capacity 400 Amps of frant/side handel.

S&F ON LOAD change over switch 415 V in sheet metal enclosures 4 pole of capacity 250 Amps of frant/side handel.

S&F ON LOAD change over switch 415 V in sheet metal enclosures 4 pole of capacity 150 Amps of frant/side handel.

Cable jointing kit for 1.1 KV (Earthed) grade cable for outdoor termination Heat shrinkable type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 16 sqmm to 35 sqmm.

Deduct Schedule of Credit of Rs as listed in Schedule 'A' Part-II. Contract Sum shall be arrived after deducting the credit amount. Note :- Tenderers will not quote against this item being a firm amount.

K S BUILDERS (BID ID -3473173)