COMPREHENSIVE MAINT IN SAPPER ENCLAVE AND OFFR MD ACCN IN AOR OF GE SOUTH UDHAMPUR

Amount

Taking down chowkhat or frames with shutters (without taking off shutters from the frames) n.exc 1.5 Sqm each including cutting holes for taking out hold fasts dismentaling brick work (holes cut and any other damages to jambs walls for taking out hold fast shall be finished identical to existing finish without any extra cost) complete all as specified and as directed.

All as per item No 1 above but exc 1.50 Sqm but not exc 4.00 Sqm complete all as specified and as directed.

Taking down shutters of any description exceeding 1 square metre each and n. exc 2 Sqm complete all as specified.

Demolition of cement concrete unreinforced in ground floors and pavings not exceeding 15cm thickness below or above ground level complete all as specified and as directed.

M & L for dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc. complete all as specified and as directed.

S&F 30mm thick Flush shutters solid core construction with particle board core and plywood face panels commercial type on both sides & one face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed.

S&F 1mm thick wood grain printed Sunmica/PVC sheet (Design as approved by Engr in Charge) fixed or laid on to flush doors by using rubber based adhesive supplying & fixing at site as per specification complete all as specified and as directed.

S&F 2nd class hard wood (sal/hollock) glazed and skelton shutters 30mm thick open rebated and prepared to receive glass gauge etc. (without sash bars) edges of framing palin chamfered or rounded fitted with cut & mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Pt-I Section 8.24(a) supplied and fitted to chowkhats complete including fixing only iron mongery such as tower bolt handle hinges aldrop bolt etc complete all as specified and as directed.

S&F solid mouled PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube and fixed in opening as per specification and drawing on page No. 150 MES SSR-2004 Part II and complete all as specified and as directed.

S & F factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (stiles) with 2 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face fixing in frame at site as per specification & drawing complete all as specified.

S&F Anodised aluminium door shutters with frame powder coating of any colour (Thickness or powder coating not less than 50 micron) aluminium section weighing 0.55 kg/m including with suitable locking arrangement with lock (Make: Godrej) 4 lever 5.5mm thick tinted glass 5mm thick aluminium push plate hydrolic door closer-01 No pivet with standard floor spring and pivot on top frame aluminium tower bolts 300 mm long-01 No glazing clips rubber packing for locking purpose with aluminium snap beading screws handles 2 Nos in each door hinges etc. complete all as specified and as directed.

S&F Powder coated (50 micron of approved colour) three track Aluminum anodised shutter window (glazed and wire gauge) fixed type with aliminium window frame or chowkat 1.50 mm thick sheet & section aluminium anodised of size 100 mm x 44.50 mm and window shutter frames made of (middle top rail bottom) and styles 1.5 mm thick aluminium anodised sheet & section of size 44.5 x 44.5 mm including all fittings such as rubber gasket aluminum glazing clips locking cabinet and 75 mm handle and including 4 mm thick tinted glass pane in panes glazed shutter fixed with rubber gasket and glazing clip/aluminium beads and with stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staples on gauge shutter including all accessories complete all as specified and as directed.

S&F 12mm Toughened glass(etching design on glass as approved by Engr in Charge) as in hinged doors partitions automatic doors and similar work including cutting to shape drilling holes required including all accessories like 18" SS handle floor machine locking system and all connected accessories etc complete all as specified and as directed.

Supply and fixing factory made uPVC white colour three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F 5mm glass exc 0.5sqm each pane (Etching design on glass as approved by Engr in Charge) as in windows, partitions, automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed.

S&F Venetian blinds of approved make, vertical/horizontal type using 100mm wide fabric blinds of approved colour/ shade and pattern including operating arrangement such as chord/ thread, counter weight, connecting chain etc., and necessary fittings complete all as specified and directed.

S&F stainless steel handles fency type 150mm size (design of handle as approved by Engr in Charge) complete all as specified and as directed.

S&F stainless steel barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and as directed.

S&F stainless steel butt hinges medium weight 100 mm long, including fixing to pressed steel/wooden/PVC door frame complete all as specified and as directed.

S&F of galvanised stainless steel wire cloth cut to size, 0.56 mm nominal dia wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and as directed.

S&F in repair galvanised stainless steel wire cloth cut to size, 0.56 mm nominal dia wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and as directed.

S& Kitchen cabinet/cupboard/Almirah in required size at site made out 18 mm thick one side decorative lamination sheet consisting of carcass 18/20 mm thick PVC sheet & provn of shutters made out of 18mm thick one side decoartive laminated PVC sheet all required brackets 5.5 screws etc. the panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish, necessary drawer, openable shelve with frame work complete as per make and specification mention as per drawing with locking arragement approved by Engr-in-Charge. Colour as approved by GE. (Make: Rajshree/Sintex or equilent) complete all as specified and as directed.

Aluminium (die cast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair complete all as specified and as directed.

S&F continous (Piano) hinges, mild steel, bright finished or electrogalvanised width of flaps in 30mm complete all as specified and as directed.

S&F in repair stain less steel door catcher of superior qualityall as specified and directed by Engr in charge

S&F for brass mortice lock of 4 levers 100 mm thick fixed in aluminium door/wooden door complete all as specified and directed.

S&F in repair CP 20mm dia, Stainless steel, tubular curtain rail, fixed with fancy brackets, complete all as specified and as directed by Engr-in-Charge.

S&F 10 ltr capacity PVC low level flushing cistern symphonic action type white with inlet valve float and handle including brackets, fixed in repairs complete all as specified and directed.

M&L for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm including taking down steel tubing with connections complete all as specified.

M&L for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20 mm including taking down steel tubing with connections complete all as specified and as directed.

S&F in repair ball valves of size 20mm bore dia high pressure of PTMT (Make-Prayag or equivalent) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and directed by Engr-in-Charge

S&F fixing in repair ball valves of size 25 mm bore dia high pressure of PTMT (Make-Prayag) with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and directed.

S&F in repair angle valve of brass fancy type, chromimum plated with long shank cast copper alloy screwed down high pressure with capstan head for iron pipe 15mm bore, complete all as specified and as directed. Make: Jaquar Cat No FON-40053 or its equivalent in Hindware/Cera/Parryware

S&F in repair PVC connection 15 mm size with PTMT nuts 600mm long, complete all as specified and as directed.

S&F in repair Single piece Water closet wall mounted pattern coloured of size: 370x695x795 mm as approved with connected accessories complete all as specified and directed by Engr-in-Charge Make: Jaquar Cat No KUS-WHT-35851S300UF or its equivalent in Hindware/Cera/Parryware

S&F in repair WHB coloured 420mm x 420 mm x 155mm with connected accesories as approved and complete all as specified and directed by Engr-in-Charge. Make: Jaquar Cat No CNS-WHT-905 or its equivalent in Hindware/Cera/Parryware

S&F in repair 15mm bore wall mixer/sink mixer/Centre hole basin mixer with round spout with 450 mm long copper pipes and brass nuts with out Pop up complete all as specified and directed. Make: Jaquar, Cat Part No CON 167KNB and equivalent in CERA/Parryware.

S&F in repair150mm dia brass chromium plated shower rose with swivel joints in repair complete all as specified and directed.

S&F 15 mm bore long body CP Bib tap in repair complete all as specified and directed. Make: Jaquar Cat Part No CON-037KN and equivalent in CERA/Parryware.

S&F in repair Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe in repair complete all as specified and directed. Make: CERA Cat Part No F8030103 and equivalent in Parryware.

Chromium plated toilet paper holder in repair complete all as specified and directed. Make: Jaquar Cat Part No ACN 1153N and equivalent in CERA/Parryware.

600 mm long brass chromium plated towel rail fancy type in repair complete all as specified and directed. Make: Jaquar Cat Part No ACN- 1111NM and equivalent in CERA/Parryware.

Soap dish in repair complete all as specified and directed. Make: Jaquar Cat Part No ACN 1131N and equivalent in CERA/Parryware.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for 15 mm thick rendering on fair faces of brick or stone/concrete surfaces in cement mortar 1:4 and finished surface even and smooth without using extra cement complete with water proofing compound all as specified.

M&L for 15 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces as on ceiling complete all as specified and as directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 15mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 Itr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.50 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm, complete all as specified and as directed by Engr-in- Charge.

M & L for 75mm thick cement concrete 1:4:8 type D-2 (40mm grade aggregate) as in sub base complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L for Granite stone 18-20mm thick (table rubbed and polished) in window cills, cooking platforms and the like, laid over cement mortar 1:3 after roughening of existing concrete surface and applying a layer of neat cement slurry @ 3Kg/Sqm including pointing in white cement 1:2 using marble dust with admixture of pigments to match with shade of stone, including demolition of stone slabs and tiles of any description or thickness in floors etc. laid, bedded and pointed in any mortar complete all as specified and as directed.

M&&L for vitrified tile (Dura stone tiles) of size 300 x 300 x 10mm thick of 400 x 400 x 10mm thick as in floors and over & including 20mm thick screed bed or bedding layer in cement mortar 1:6, including jointed with neat cement slurry and pointed in coloured cement to match the surface of tiles, complete all as specified and as directed.

M&L for vitrified tiles light shade double charged glossy finish of 8-10mm thick (Square / rectangular) polished, area of each tiles not exceeding 0.36 Sqm as in floors set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or beddding layer in cementy mortar 1:4 complete all as specifed and as directed.

M&L for 600x1200mm vitrified tiles light shade double charged glossy finish or size as approved by Engr in charge of 8-10mm thick (Square / rectangular) polished, area of each tiles exceeding 0.42 Sqm but n exc 1.00 Sqm as in floors set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or beddding layer in cementy mortar 1:4 complete all as specifed and as directed.

M&L for vitrified tiles light shade double charged 8-10 mm thick (Square / rectangular) polished, as in vertical surface/skirting set and jointed in neat cement slurry and pointed in coloured cement to match over 10 mm thick screed bed or beddding layer in cementy mortar 1:4 complete all as specifed and as directed.

M&L Non skid ceramic coloured floor tiles 7-8mm thick, area of each tiles exceeding 0.11 Sqm but not exceeding 0.18Sqm or of size as approved as in floors set and jointed in neat cement slurry and pointed in white cement with pigments to match over and including the provision of 15 mm thick bedding layer in cement mortar 1:4 complete all as specified and as directed.

M&L glazed ceramic coloured tiles 300mm x 600mm x 7mm thick as in vertical surfaces of walls, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm cement rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for chequred cement concrete tiles(glosy finish premium quality) 300mm x 300mm x 20-25mm thick, set jointed and pointed in neat cement slurry in floor with grey cement and pigment including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates to Fe-290 (Gde E-165) complete all as specified and as directed.

S&F 0.50mm thick prepainted galvalume aluminium zinc coated Gl based semi corrugated/profile steel sheeting of any colour, having tensile strength of 550MPA as in roof covering, wall cladding with self tapping screws or 'L' type of 'J' type or cranked hook bolts in lieu of screws as per manufacturers instructions including dismantling translucent PVC or Asbestos cement corrugated sheets including ridges as in roof coverings, complete all as specified and as directed.

S&F 0.50mm thick prepainted galvalume aluminium zinc coated Gl based plain steel sheeting of any colour, having tensile strength of 550 Mpa as in roof covering, wall cladding with self tapping screws or 'L' type or 'J' type or cranked hook bolts in lieu of screws as per manufacturers instructions, including dismantling translucent PVC or Asbestos cement corrugated sheets including ridges as in roof coverings, complete all as specified and as directed.

S&F solid PVC wall lining (wall panelling design and colour shall be approved by Engr in Charge) consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement & PVC framework/beading as required and fixing at site on PVC frame, complete all as specified and directed.

S&F in repair 4mm thick Cement fibre board (designer ceiling) of size 600mm x 600mm panel conforming to IS 14862 type B category three including Gl frame work with size of grid 605mm x 605mm including all accessories and Gl suspensions, the fibre sheet should be fire resistant, water resistant, termite resistant, environment friendly & 100% asbestos free, including dismantling existing wall and ceiling boards (fibre pulp, insulation etc) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and as directed by Engr-in-Charge.

S&F in repairs 10-12mm thick perforated gypsum boards seemless as in ceiling as approved, moisture resistant, including intermediate, perimeter channel wall channel, along with nuts and bolts connecting plates for gypsum boards, dry wall screws soffits cleats, ceiling section, rowel plugs fixtures and screws and applying two coats of emulsion paint over a coat primer on exposed surface, including dismantling wall and ceiling boards (fibre pulp, insulation etc) or insulation boards / slabs / blankets, any thickness, including cover fillets, of complete all as specified and as directed by Engr - in - Charge. Note: (a) Design of paneling board as approved by Engr - in - Charge (b) Gl grid, hanhing system shall be of same manufacture.

M&L for EPDM (Ethylene Propylene Diene Monomer) waterproofing membranes of minimum tensile strength of around 9 MPa, elongation at break over 300%, and a wide service temperature range, typically from -40°C to +140°C, resistant to UV, ozone, and temperature variations, with thicknesses ranging from 1.20-1.50 mm complete all as specified and as directed. Make: Kiran Rubber (KRUBBER™), Polygomma, Softex Industrial Products, Mnm Composites, and Osaka Rubber (ORPL)

M & L for brickwork with subclass 'B' bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 including demolition of brick work complete all as specified and as directed

Preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Preparation of new wooden surfaces and applying two coat of synthetic enamel paint over a coat of pink primer on wooden surfaces of any description, not otherwise described over 10cm width or girth, complete all as specified and as directed.

Preparation of old wall surfaces with washing, rubbing down and stopping of distempered wall surfaces and applying one coat of OBD, white/ coloured complete all as specified and directed.

M & L for applying two coats of synthetic enamel ordinary tint paint including red oxide primer and preparation extra complete on new steel or iron surfaces of any description, over 10cm in width or grith, not otherwise described complete all as specified.

Applying one coats of weather proof exterior emulsion paint (Asian Ultima APEX or Berger Weather Allguard or equivalent) over to G+2 floor height etc including preparation of surface complete all as specified and directed.

Preparation of old decoarated wall/ceiling surfaces and applying one coat of wall care putty (Make: Birla or equivalent) up to G+2 floor height complete all as specified and directed.

Preparation of old painted wooden/Steel surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F for Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing; frame work for water tanks staging and similar work conforming to Fe 410-0 or Fe 310-0, complete all as specified and as directed.

S&F rotational moulded polyethene water storage tank 500 Itr capacity hoisted and fixed in position including dismantling of existing tank, complete all as specified and as directed.

S&F rotational moulded polyethene water storage tank 1000 ltr capacity hoisted and fixed in position including dismantling of existing tank, complete all as specified and as directed.

M&L of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replunging them with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed. Note: ATT shall be done authorised applicator approved from Pest Control of India and odourless chemical shall be used.

M&L at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed.

M&L Treatment of Soil under existing floors using emulsion @one litre for hole 300mm apart including drilling and plugging 12mm dia holes with cement mortor 1:2 to match the existing floor complete all as specified and as directed.

s l sharma and sons (BID ID -3519004)

VISHWANATH AND SONS (BID ID -3518714)

vmd traders (BID ID -3518794)

M/S ASHOK KUMAR PACHIALA (BID ID -3520196)

S K BROTHERS (BID ID -3519856)

AKBAR FURNITURE HOUSE AND TIMBER MERCHANT (BID ID -3520224)

KESAR CONST CO (BID ID -3520336)

m/s sushila devi (BID ID -3520012)

Sh. Manmeet Kumar S/o Late Sh. Rattan Gopal (BID ID -3519973)