REPAIR /REPLACEMENT OF INTERLOCKING TILES, CHEQUERED TILES, REPAIR TO DRAIN, PATH, GRIT PLASTER, HARD STANDING, MANHOLE/ DRAIN COVERS, RCC JALLIES FENCING, WPC JALLIES AT 261 ARTY BGDE, 512 LT MSL RAGMT, 110 MED REGMT, OTHER UNITS AND ACCN IN THE ARE

Amount

Taking down cement plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc, Complete all as specified and directed

Demolition of plain cement concrete in ground floor and paving not exc. 15 cm thick (below or above) ground level, complete all as specified & directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion embedded in concrete, brick work, masonary etc,and making good disturbed ground complete all as specified and directed.

Dismantling fencing wire mesh, any type any size, complete all specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floor, aprons etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling AC sheet/CGI sheet/PGI Sheet/tensile fabric sheet (corrugated, semi corrugated, etc) in roof covering, complete all as specified and directed.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering, cladding to wall, ridges etc. fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm complete all as specified & directed by engr-in-charge

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape (Jhhallar) as directed at site fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm complete all as specified & directed by engr-in-charge

S & F Mild Steel Framed work as in Gate of angle or other section with gusset plate, rails, braces, stair case, barreled iron doors, ladders, framed balusters; walk ways, railings, framework of water tanks, cover grills, tubular trusses and similar work etc Fe.290.Gde-E-165 complete drilled for fixing of steel sheeting or other covering including welding work, (PCC 1:1.5:3) etc to be prepared for hanging or sliding with and including either hooks, hinges, necessary holdfasts or steel hanging door fittings, locking arrangement, gate closer, stopper etc and hanging also fastening and fixing in building upto 8 mtr height complete all as spfd and directed by engr in charge.

S&F mild steel work as in joist channels, angle or tee section, fixed independently w/o connecting plate conforming to Fe.290.Gde-E-165, incl cutting tops to shape as directed, drilling holes,notching for wire, welding work etc. flat iron fillets incl all necessary drilling, bolting or riveting, etc. ,drilled and countersunk for balusters running bars, nosing to steps incl embeding in concrete and screwing etc. wind ties for roof including securing bolts;, and similar work including necessary cutting,drilling,welding etc. complete all as specified and directed by engr-in-charge

Providing and fixing at site Factory Made 24 mm thick 100% Solid WPC (Wood polymer Composite ) Plain Jali cut on CNC machine of approved design & Colour, measured size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm manufactured by an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with MS Hollow pipes frame & MS Square bar incl stainless Steel Screws / Fastners or required length all as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company. Make :Make : Rajshri / Fenesta / Ecocell.

Excavation in post holes (or similar holes) in Soft / loose soil each not exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good final finished surface complete all as specified and directed.

M&L Cement concrete type C2 1:3:6 (using 40 mm graded aggregates) in foundations, filling and mass-concrete incl required formwork complete all as specified and directed.

S&F M S Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shapeas directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts, etc including provision of binding wire complete all as specified and directed.

Supply only chain link MS galvanised fencing, any size, shape or any type complete all as specified and directed by Engr-in-Charge.

M&L rendering 15mm thick in Cement Mortar 1:4 on fair faces of brick or concrete, external surfaces of walls finished and even & fair without using extra cement complete all as specifed & as directed. (incl new brick work)

M&L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels made by wooden beads with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified including using white cement in place of grey cement for grit wash complete all as directed.Note:- This item includes use of necessary scafffolding and safety net up to G+5 storey building and no extra payment shall be paid for that. Contractor should keep this aspect in mind while quoting the rate

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and directions of Engineer-in-charge.Note:- This item includes use of necessary scafffolding and safety net up to G+5 storey building and no extra payment shall be paid for that. Contractor should keep this aspect in mind while quoting the rate

M & L for preparing the newly plastered wall surface and applying primer with applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sq complete all as specified and directed. (Note: Quoted rates shall be deemed included painting at any height including scaffolding work, as required)

M&L 16 mm to 18 mm thick granite (of any type) (approved colour) machine cut as in vertical surfaces and skirting/ dado or in staircase laid asper SSR Part-I over including 15 mm thick rendering in CM 1:4 jointed with grey cement slurry and pointed with white cement with admixture of of pigment to match the shade of granite stone incl grinding and polishing and using fasteners to hold the granite firm complete all as specified.

M&L 100mm thick PCC 1:4:8 type D-2 (using 40mm graded crusted stone aggregate) as in sub base of floor, complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge prepolished cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.

Demolition of reinforced cement concrete as in RCC slabs, beams, etc drains or manhole covers of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

S&F Factory made precast heavy duty drain/ manhole covers including MS frame and including reinforcement as per IS 12592 : 2002 with MES engraved in it and with specified thickness complete all as specified and directed .

M&L for RCC work (Nominal Mix) (1:2:4) type B-1 (using 20mm graded stone aggregate) as in slabs supported on walls, man hole cover, drain covers, Shelves etc and like complete all as specified and as directed.

M&L for TMT bars of 8 mm dia and over, cut to lenghth bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface flat for rough finished surface of concrete complete all as specified.

S&F Factory made precast perforated heavy duty drain/ manhole covers including MS frame plate and including reinforcement as per IS 12592 : 2002 with size 1.00mtr x 0.50mtr x 75mm thickness, complete all as specified and directed by Engineer-in-Charge.

M&L for PCC type B1 1:2:4 (using 20mm graded crushed stone agg) in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelersm apexstone, bed plates, including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C-2, (using 40mm graded stone aggregate) as in plinth protection laid in bays and surfaces finished even & smooth without using extra cement, complete all as specified.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete

M&L for preparing newly concrete surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonary built in cement mortar including all quoins arches, pillers etc but excluding ashler facings dressed stone work and precast concrete articles complete all as specified and as directed by Engineer-in-Charge.

M&L for brick work straight or curved on plan exc 6m mean radius in cement mortar (1:4) with Sub class ‘B’ brick including manhole raising,drains,septic tanks footpath,boundary wall etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing factory made prepolished chequred cement concrete coloured tiles 300mm x 300mm x 25 mm thick, set jointed and pointed in neat cement slurry with grey cement mixed with pigment to match the colour of tiles, laid over and incl 20mm thick screed bed in CM 1:6, complete all as specified & directed.

M&L for PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in surface channels and drains finished even and smooth including use of necessary form work and finishing exposed surfaces even and smooth using cement slurry using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of newly painted steel or iron surfaces of any description over 10cm width or girth and applying two coat of synthetic enamal paint of tint as approved complete all as specified and directed.

Supply & fixed in replacement Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed by Engr-in-Charge.

Restraining and rescecuring Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)complete all as specified and directed by Engr-in-Charge.

S&F in replacement of concertina coil fencing with punched tape, 600mm dia, , having 50 Nos rounds per 6m length, laid on ground or fixing the same on Y-shaped angle iron with necessary G.I staples / GI clips to retain in horizontal position including necessary bolts, fasteners and binding wire complete all as specified and directed.

S&F in replacement of concertina coil fencing with punched tape, 450mm dia, , having 50 Nos rounds per 6m length, laid on ground or fixing the same on Y-shaped angle iron with necessary G.I staples / GI clips to retain in horizontal position including necessary bolts, fasteners and binding wire complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L Coloured Glazed ceramic tiles in vertical surface 600mm x 300mm x 7-9 mm thick,jointfreeexternal based such as stone craft, wood craft, brick craft, pebble craft etc such as etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match and laid over and incl 10 mm thick screed bed in CM 1:4, complete all as specified and directed.

M & L Coloured Glazed ceramic tiles in vertical surface 450mm x 300mm x 7-8 mm thick, such as skirting, dados , etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match and laid over and incl 10 mm thick screed bed in CM 1:4, complete all as specified and directed.

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match laid over and incl 15 mm thick avg screed bed in CM 1:6, complete all as specified and directed.

S & F in replacement 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to wall completed all as specified and directed (Note : The quoted rate is inclusive of necessary scaffolding for Pipe work executed in shaft area upto the 10 storey building).

S & F repair 110 mm PVC (SWR) bends with acess door completed all as specified and directed

S&F in replacement 75mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints ,laid in trenches or in floor or in wall complete all as specifed and directed.

S & F in reapir 75 mm dia PVC Bends with access dooe complete all as specofied and directed

S & F in reapir 110 mm dia singleTEE for PVC (SWR) pipe complete all as specified and directed

BLANK

M&L for providing precast cement concrete louvers and jallies, 35 mm thick type B- 0, 1:2:4 (using 12.5mm graded stone aggregate) (measured solid) including all moulding and necessary form work and set in cement mortar 1:4 fixed in repairs complete all as specifed and as directed.

S&F precast RCC coping/post 1:2:4 type B-1 (using 20 mm graded stone aggregate) of size 600x100x50 mm suitable for fixing of RCC Jallies in vertically & horizontally including necessary moulds and grooves as required in shape and size complete all as specified and directed.

M&L for providing PMM including demolition(Polymer modified cementitious mortar) :- (i) Dry sub strate surface and free of debris & dust (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness. Note : Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use. (iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed.

Providing services on related to welding & blacksmith work based on day to day complaints on all working days (except Sunday and gazetted Holiday ) from 0900 hours 1700 hours complete all as specified and directed. Note- 1.The above task shall be carried out by deploying minimum 01 welder having blacksmith skills and 01 Helper on daily basis. 2) Necessary T&P, ladders,minor consumable viz welding rods/extras, equipments and safety gear shall be provided by the contractors.

S&F in replacement Steel rolling shutters, with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer;1.25 mm thickness of lath erected in position as indi cated, complete gear operated type with bevel gear box and crank handle complete all as specified and directed

S& F Safety lever locks mild steel with 4 levers for rolling shutters

S&F for ball bearing for rolling shutters complete all as specified

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement

S&F MS round bars 10 mm dia Gde Fe-410-W quality A for fixing of chain link fencing complete all as specified and directed

Cutting shrubs, wild growth/trees n exc 30cm girth and removing complete vegetation growth from walls incl taking out roots from roofs/brick work and making good the disturbed surface with PCC 1:2:4 type B-0, using 12.5mm graded crushed stone aggregate including treating affected area with acid wash to check further growth of vegetation and disposing off the rubbish from site (MoD Land) from the above mentioned area complete all as specified and as directed. (Note: The unit quoted rates shall be deemed included steel scaffolding / jhulla with safety equipment upto 9 storey bldg)

Dismentling boarding, any description, fixed in any positioin with nails complete all as specified

Providing and fixing GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bendingtiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

M&L for decorative wall panelling with PVC louvered/Fluted/Plain 2D/3D wall panels with plastic and silicate mixture as the core material with inand surface with PVC foil on the top with thickness of panel 10mm to 20mm, width of 150mm to 200mm and length of 2.74/3.05 (9' or 10') meters of POLYWOOD or equivalent brand Wt of PVC pannel is 4.5 kg/sqm and PVC percentage in wall panels is more than 40% including necessary L/H/U corner profile and fillets. WPC Wall panel are termite proof , water proof and usable on the damp walls, fixed to wall/ ceiling surface as per manufacturer instruction complete all as specified and directed by Engr-in-charge. Note:The rates are inclusive of corner profiles and fillets

Note :- The work described in these items shall be executed in bldgs up to (G+8 floor) hence the contractor shall make scaffolding arrangements, trestles, ladders etc and hessian clothes where required, for protection & all other safety precautions up to 09 storeys of buildings and the cost for the same shall be deemed included in the quoted unit rates. Note :- Removing building materials /old waste unwanted existing material of any description or any type etc.on alternate day to a distance of 5km or beyond out side MOD Land and the cost for the same shall be deemed included in the quoted unit rates.

KKP Enterprises (BID ID -3468296)

MS BUILDTECH (BID ID -3468766)

STAR CONSTRUCTION CO (BID ID -3468954)

M/s Shubh Enterprises (BID ID -3468650)

MAA SANTOSHI ENTERPRISES (BID ID -3468755)

S GOURAV PRAKASH ENTERPRISES (BID ID -3468852)

M/s Nikhil Kumar Builders (BID ID -3468151)