SPECIAL REPAIR OF BLDG NO. P-80/1 TO 04 (JCOs MD Accn) AT NAR BAHADUR ENCLAVE OF MH JABALPUR UNDER GE (WEST) JABALPUR

Amount

M&L for 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in foundation, filling, mass concrete and sub base of floors, path/ paving etc complete all as specified & directed.

M&L for 60mm thick rubber mould reflective factory made coloured pre cast PCC interlocking paver blocks/ tiles conforming to IS 15658-2006, M-35 designation of section as approved by GE, in hard standing, laid dry over & including 50mm thick sand cushion and filling the voids of paver blocks/tiles with dry sand complete all as specified & directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.50M clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm in height, copings, kneelers, apex stones, bed plates etc and the like including weathering slightly rounded/ chamfered angles with & including necessary use and waste of form work for fair faces of concrete, complete all as specified and directed. Notes:- Reinforcement where provided shall be measured and paid for separately.

M&L for Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

Cutting chases in brick walls, pinning in brick wall/ stone concrete block or slab walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings , etc and making good as per existing, cutting not exceeding 10cm girth complete all as specified and directed.

Use and waste of Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, etc. surface fair finished complete all as specified and directed.

M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in chajja complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately under respective item of BOQ.

Use and waste of Formwork to chajjas, troughs and similar items including edges etc. complete all as specified and directed.

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

M&L for brick work with sub class B, fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

Supply only water proofing compound (liquid) ISI marked of make as approved by GE complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area n.exc 1.5 sqm each and removal complete all as specified & directed.

Taking down Chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 sqm but n.exc 4 sqm each and removal complete all as specified & directed.

Supply & fix factory made solid PVC door frame of size 50mmx47mm made out of 5mm single side prelam PVC sheet reinforced with MS square tube and edges painted to match with printed sheet complete all as specified & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed in frame complete all as specified & directed.

M&L for factory made second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats complete all as specified & directed. Notes:- (i) glazing will be measured and paid for separately. (ii) Butt hinge will be measured and paid for separately .

M&L for factory made 35mm thick second class (Indian Sal, Bijasal, Hollock or Benteak) hardwood plain, framed, panelled shutter (two or three panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stiles as per IS: 1003 (Part-I), kiln seasoned complete all as specified & directed.

S&F of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed with tinned tacks or galvanised wire staples complete all as specified & directed.

Supplying & fixing Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. including locking arrangement for fixing etc complete with shutters, frames and grills complete all as specified & directed.

Supplying & fixing 300 mm long aluminium alloy, anodised sliding door bolts with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded section and fixing bolts & sliding bolts of extruded section or cast aluminium alloy complete all as specified & directed.

Supplying & fixing 100mm size butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized, type B-21 complete all as specified & directed.

Supplying & fixing continuous (Piano) hinges, mild steel, bright finish or electro galvanized, 30 mm width of flaps (when open) complete all as specified & directed.

Supplying & fixing 200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supplying & fixing 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified & directed.

Supplying & fixing 300 mm size ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified & directed.

Supplying & fixing 125 mm hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified & directed.

Supply and fix extruded aluminium anodised alloy handles 150 mm size, fabricated type complete all as specified & directed.

Supply and fix extruded aluminium anodised alloy handles 125 mm size, fabricated type complete all as specified & directed.

Supplying & fixing floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete all as specified & directed.

Supplying & fixing 25 mm dia mild steel, drapery rod with PVC coating fixed in the MS hook and side brackets (both side ) shade as approved by GE complete all as specified & directed.

Cutting holes in brick walls exc half brick and not exceeding full brick built in cement mortar for inserting holdfasts and making good dismantled portion using cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

M&L for 19mm thick water proof block board, exterior grade Gde-1 fixed with & including suitable size clamps, glue & screws etc as kitchen, cup board box ,shutter & shelves complete all as specified & directed.

M&L for 18mm thick PVC sheet one side prelaminated of approved texture as in kitchen cabinet ( with shelves and partition) including necessary fitting & fixture as per manufacturer instructions complete all as specified & directed.

Supplying & fixing stainless steel handle of 150 mm including all connection fitting complete all as specified & directed.

Supplying & fixing Europa cup board locks complete all as specified & directed.

Supply & fix 75 mm size stainless steel hinges including all connection fitting complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

M&L for mild steel conforming to Fe.290.Gde-E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified & directed.

S&F Hat and coat hooks of brass, solid body, 175mm to 250 mm complete all as specified and directed.

S&F of stainless steel peg set of 6 Nos fixed to wooden plank complete all as specified and directed.

M&L for mild steel TMT bars 8mm dia as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for 15 mm thick plaster in CM 1:3 in two layers, with and including wire netting of galvanized steel wire 0.91 mm dia and mesh size 12 mm placed in wall before plaster layers and fixed with tinned tack or wire stapled where required first layer of 10 mm thick plaster in cement mortar 1:4 & second layer of 5 mm thick in cement mortar 1:3 including taking down of loose/bulging surfaces of plastered or concrete as in chajjas, beam balcony fins etc in multistoryed buildings, top layer of plaster finished even and smooth without using extra cement complete including cleaning and peparation of existing RCC surfaces and apply a coat of cement slurry and surface shall be match & finish the existing surface by applying two coats of anti fungal exterior emulsion paint complete all as specified & directed.

S&F of expanded metal not exceeding 4 Kg per Sqm in weight, cut to length, bent to shape required and tying with & including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples to brick wall/ stone block or slab wall complete all as specified & directed.

Supplying & fixing for 125x60mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

Supplying & fixing for 105x60mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) including removal of debris to out side MD land complete all as specified & directed.

M&L for glazed ceramic coloured tiles 450x300x7mm thick as approved by GE on vertical surfaces such as skirting/ dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for non-skid coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11Sqm but not exc 0.18Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for non-skid coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.18Sqm but not exc 0.36Sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 15 mm thick screed bed in CM (1:6) complete all as specified & directed.

M&L for non-skid joint free coloured ceramic tiles 7-8mm thick (square/ rectangular) area of each tile exc 0.11Sqm but not exc 0.18Sqm as in skirting/ dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles, laid over and including 10mm thick rendering in CM (1:4) complete all as specified & directed.

M&L for Machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified & directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and using Screed bed or bedding layer of mortar 20 mm thick in CM 1:6 for laying floor finishes complete complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring, 18-20mm thick over & including 20 mm thick cement screed bed in CM (1:6) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for machine cut kota stone slab as in skirting/ vertical surface, 18-20mm thick over & including 10mm thick rendering in CM (1:4) laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified & directed.

M&L for coloured cement concrete tiles 250mm x 250mm x22-25mm thick, machine pressed, machine cut and polished, set, jointed and pointed in neat cement slurry mixed with pigment to match with the shade of tiles, , in floors, laid over and including 20mm thick screed bed in CM (1:4) complete all as specified & directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified & directed.

M&L for 25 mm thick, PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in sub base of floors and the like etc considering the floor slope complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate in roof padding, roof kerbs or mud stops, rounded or chamfered on edge including necessary form work if required complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete and sub base of floors, path/ paving etc complete all as specified & directed.

M&L Bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5 kg. per sq. m per coat and Polythene film, black, 50micron laid in floors complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement forming joints to full depth at every 3M intervals and at every change of direction and filing with bitumen sand mixture 1:3 by weight complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 using 20 mm graded stone aggregate as in filling of pressed steel door frame etc complete all as specified & directed.

Taking down cement plaster etc on brick walls/ terrazo surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

M&L for 10mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

M&L for 15mm thick rendering in two layers, first layer 10mm thick in CM 1:6 and other finishing layer 5mm thick in CM 1:4 with and including water proofing compound @ 2% by wt of cement or as per manufacturer's instructions on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified & directed.

M&L for rendering 15 mm thick in CM 1:4 with liquid water proofing compound as per manufacturer instructions and finished even and fair complete all as specified and as directed. (Note :- WPC shall be measured and paid for separately as " Supply only".)

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling finished even and smooth without using extra cement complete all specified and directed.

M&L for preparing new plastered or unplastered surfaces of wall and applying three coats of white wash as in wall complete all as specified and directed.

M&L for preparing of old plastered or unplastered surfaces of ceiling ( preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots ) and applying one coat of white wash complete all as specified and directed.

M&L for prepration of new plastered surfaces of external walls and applying two coats of cement base paint over & including a coat of alkali resistant primer complete all as specified & directed.

M&L for complete removal of existing treatment and preparation of old plastered surfaces of wall of any description and applying two coats of cement base paint wall surface over & including a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and apply two coats of oil emulsion distemper over 3 mm thick of Birla/ JK wall care putty over a coat of cement primer for smooth finish of wall complete all as specified and directed.

M&L for complete removal of existing treatment and preparation of old plastered surfaces of wall and apply two coats of oil emulsion distemper over 2 mm thick of wall care putty in two layers, over a resistant priming paint for smooth finish of wall complete all as specified and directed.

M&L for treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sq. m each complete all as specified & directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coat synthetic enamel paint of colour as approved by GE over and including a coat of pink primer complete all as specified & directed.

M&L for preparation of old painted surface of wood and wooden based material of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of synthetic enamel paint of colour as approved by GE over and including a coat of red-oxide primer complete all as specified & directed.

M&L for preparation of old painted surfaces of steel of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed.

Supply & fix 32 mm bore, low density polyethylene pipe (LDPE) pipes, of pressure rating 6 Kg/cm2, fixed to walls, ceilings or laid in floor fixed complete all as specified and directed.

S&F in repairs, 15mm dia bib cock with wall flange ,cast copper alloy with crutch or butterfly handle, fancy type, chromium plated, screwed down for iron pipe or brass ferrule complete all as specified & directed.

Supply and fix in repairs, 15mm dia stop valves/ angle cock, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified & directed.

S&F in repairs chromium plated brass tubular towel rail, 20mm dia, D type, 600 mm long between flanges complete all as specified and directed.

S&F in repairs chromium plated brass tubular towel ring, round type fixed with screws and wooden or plastic cleats complete all as specified and directed.

Supply & fix in repairs vitreous china squatting pan, Orissa pattern of size 580x440 mm white, with integral foot rest and PVC 'P' or 'S' trap including connection to trap, and to flush pipe, etc (excluding flushing pipe) and making good to floor complete all as specified & directed.

S&F in repairs 10 ltr capacity PVC valve less syphonic action type flushing cistern low level 'white' with inlet ball valve, float valve & handle Including 32mm bore PVC flush pipe & brackets and brackets fixed to wall complete all as specified & directed.

S&F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts complete all as specified & directed.

S&F in repair, CP shower rose 125 mm dia of size suitable for 15mm bore GI pipe with or without swivel joint including fixing to pipe and union as approved by GE complete all as specified and directed.

S&F in repair 15 mm bore brass chromium plated WHB mixer for mixing hot and cold water along with CP brass caps screwed for fixing complete all as specified and as directed.

S&F in repair 15 mm bore brass chromium plated wall mixer, 3 in 1 system with hot and cold water arrangement with provision of both hand shower and overhead shower complete all as specified and as directed.

S&F in repairs, sheet glass corner shelf set of three assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing, design & make/ pattern as approved by GE complete all as specified & directed.

Supply & fix in repairs kitchen sink with drainage board made of stainless steel 1.0mm thick with plug, washers with and including 32 mm dia PVC rigid waste pipes and C.P coupling including fixing cantilever brackets of suitable shape & size as required at site and connecting unions to pipe, overall size 915 mm x 460mm, bowl size 410 mm x 330 mm x 160mm and necessary cutting to slab complete all as specified & directed.

Supply & fix in repairs kitchen plate rack made of stainless steel 1.0mm thick with overall size of 1200x 900 mm x 200 mm width of trade pattern complete all as specified & directed.

Supply & fix in repairs vitreous china white WHB (550 x 400 mm) flat back with CP waste coupling, waste pipe, brackets including cutting for and pinning in ends of brackets complete all as specified and directed.

M&L for Waste fittings, brass, chromium plated for glazed ware sinks of 32 mm dia. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

M&L for Waste fittings, brass, chromium plated for glazed ware sinks of 40 mm dia. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 15mm bore of pipe complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for refixing or removing to store of size 20mm bore of pipe complete all as specified and as directed.

Supply & fix 40mm bore medium grade galvanised steel tubes with all fittings and fixed complete to walls and ceilings or laid in floor complete all as specified & directed.

Supplying and laying of CPVC pipes 16 mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and nrass treaded fitting for fixing taps and valves complete all as specified and as directed.

Supplying and laying of CPVC pipes 20 mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and nrass treaded fitting for fixing taps and valves complete all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints,fixed to wall or laid in trenches or in floor with & including necessary clamps of requird size etc complete all as specifed & directed.

Supply and fix 75 mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floor with & including necessary clamps of requird size etc complete all as specifed & directed.

Supply & fix of PVC (SWR) branch piece (single Y), equal or unequal, 110 mm bore with access door rubber ring joint fixed to wall complete all as specified & directed.

Supply & fix of PVC (SWR) branch piece (double Y), equal or unequal, 110 mm bore with access door rubber ring joint fixed to wall complete all as specified & directed.

Supply and fix 110 mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply and fix 75 mm bore PVC (SWR) bends of any radius provided with access door complete all as specified & directed.

Supply & fix PVC (SWR) junction single (single T), equal or unequal provided with access door, 110mm bore complete all as specified & directed.

Supply & fix PVC (SWR) junction single (single T), equal or unequal provided with access door, 75 mm bore complete all as specified & directed.

S&F in repair Grating doom 125mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

S&F in repair 100 mm dia of Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F in repair 75mm PVC (SWR) multi floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Supply and fix of 110mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified & directed.

S&F in repair PVC (SWR) gully trap, out let dia 125/110mm, plain with grating including jointing with solvent complete all as specified and as directed.

S&F of Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore etc. complete all as specified and as directed.

Supply & fix in repairs,Soap dish, stainless steel, approximate size 160x 160x90mm complete all as specified and directed.

S&F figured glass, pin head type 4.0 mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in old work, serviceable beads as obtained from hacking out of sheet glass shall be re-used after cleaning/ rubbing the the same with sand paper, if required as per site. (ii) Glazing in new work, beads shall be supplied with joinery.

Supply and fix sheet glass, ordinary quality 3.0 mm thick and glazing with oil putty/ beads in squares n. exc 0.5sqm in each pane complete all as specified & directed. Notes:- (i) Glazing in new steel work/ joinery, rate of oil putty shall be deemed to be included in the unit quoted rate for this item. (ii) Glazing in new wood work/ joinery, beads shall be supplied with joinery.

S&F PVC bathroom cabinet of white/ivory colour with mirror of size 400 mm x 500 mm pasted coloured with mirror shutter and built in shelves complete all as specified and as directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Demolition of reinforced cement concrete Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work any description and in any position not otherwise specifically provided for reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Demolition of cement concrete of any description (unreinforced) in ground floors and paving not exceeding 15 cms thickness (below or above ground level) including removal of debris to out side MD land complete all as specified & directed.

Demolition of Concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified & directed.

M&L for Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq.m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area) complete all as specified & directed.

M&L for 10mm thick rendering over roof surfaces in CM 1:3 with using water proofing compound @ 3% by wt of cement or as per manufacturer's instructions, finished even and smooth without using extra cement complete all as specified & directed. Note: WPC shall be measured and paid separately as "Supply Only" under respective item of BOQ.

M&L for applying evenly tack coat of hot blown bitumen 85/25 grade conforming to IS-702 @ 1.20 kg/sqm after cleaning the surfaces over & including a coat of bitumen primer @ 0.30 litre/ sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil on the top of prepared roof surfaces complete all as specified & directed.

M&L for unrolled over the bitumen coated surface, 3mm thick spun bonded non-woven polyester reinforced APP modified water proofing membrane weighing not less than 3.0 Kg/Sqm with minimum over lap of 100mm and over lap shall be sealed by flame as per manufacturer's instructions complete all as specified & directed. Note:- Suitable embedment of APP modified water proofing membrane shall be ensured into walls/parapet walls, special care shall be taken in laying APP modified water proofing membrane in situations such as drain/ expansion joints etc.

M&L for applying two coat of bituminous aluminium paint @ 200gm/ sqm over polymeric membrane complete all as specified & directed. Note- Bituminous aluminium paint shall be of same manufacturer's as specified for polymeric water proofing membrane.

Taking down/ removing existing roof treatment over roof slab, roughening surfaces of old concrete floor/ roof/ terrace by picking and wire brushing the surface to remove the loose concrete, dust etc sweeping clean and washing down with water to remove dust, etc including removal of debrise to a distance 50 m out side MD land complete all as specified & directed.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified & directed.

Taking down of existing exhaust/ ceiling fan of any size/ sweep and depositing in the safe cosdoy of MES store complete all as specified & directed.

Taking down main switches/ DB's (alongwith existing board, MCBs & isolators) including removing the same from site and making good disturbed surfaces complete all as specified & directed.

Taking down existing old/ unserviceable sub main wiring of any type and description, removal of teak wood batten/ PVC pipe/ PVC casing & caping and making good disturbed surfaces of walls, ceilings etc as per existing complete all as specified and directed.

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 25 mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 4sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for provision of sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC conduit medium grade ISI marked not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, multistranded copper conductor cable of size 6 sqmm as earth continuity and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish complete all as specified & directed. Notes:- (i) Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6 sqmm cable alongwith PVC conduit and its accessories shall be measured and paid one unit length. (ii) Connections of cables with MCBs or bus bars shall be done through appropriate size brass/copper thimbles. (iii) Colour coding for wiring/ bus bar/ main connection shall be followed .

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/ regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one light /fan/exhaust/bell point controlled by one no one way switch 5/6 Amps complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on the same board with other switches complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/5 pin, 5/6 Amps controlled by one no one way piano type switch on independent board but not below the switch board of light points in same vertical plane complete all as specified & directed.

M&L for point wiring concealed type with 2.50sqmm PVC insulated, unsheathed, single core, multistranded copper conductor FRLS cable 1100 volts grade including 1.5sqmm PVC insulated unsheathed multistranded copper conductor FRLS cable as earth continuity conductor drawn through in and including rigid PVC conduit not less than 20mm dia with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0mm thick ISI marked laminated/ ebonite sheet cover for fixing switches/ socket/regulators etc including all fixing accessories and cutting chases as per standard engineering practice & making good the disturbed surfaces as per existing finish for the one socket out let 3/6 pin, 15/16 Amps controlled by one no one way piano type switch on independent board complete all as specified & directed.

Supply & fix in repair bell, Ding Dong AC. 230 volts, single pole suitable for AC 230 volt single pole complete all as specified and directed.

Supply & fix switch piano, flush type single pole, one way 5/6 Amps, 240 volts complete all as specified & directed.

Supply & fix socket outlet 2 in 1, 2 pin 5/6 Amps and 3 pin 5/6 Amps, flush universal type complete all as specified & directed.

Supply & fix switch socket combination 2 in 1, 3 pins 5/6 Amps and 3 pins 15/16 Amps flush universal type controlled by one switch complete all as specified & directed.

Supply & fix ceiling rose, surface bakelite, 65x50mm surface type, two to three terminals, AC 240 volts complete all as specified & directed.

Supply & fix in repairs, rotory stepped type electronic fan regulator mini flush type 120/ 280 Volts complete all as specified & directed.

Supply and fix in repairs, angle type lamp holder insulated with polycarbonate body and back plate housed with porcelain base suitable for 12 Watt LED with and including 12 Watt LED lamp complete all as specified and directed.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S & F, in repair, Smart bright Batten Series, LED luminaire using LED 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LED and delivers consistent light output, stable color, start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.

Supply & fix in repairs, LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete complete all as specified & directed.

S & F, in repair, Bulk head endura LED light fitting complete with and including 10 watt LED lamp and making necessary electric connection to ceiling rose with copper conductor of suiyable size & length complete all as specified & directed.

Supply and fix in repairs, 35 watt new generation energy saving and environmental friendly long life LED security light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening separate driver compartment with IP66 protection and impact resistance of IK08 on bldg wall with and including pipe bracket made of G.I tubing 32/40 mm dia bore medium grade ISI marked 1.20m long bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/ MS clamps & 12mm dia bolts, nuts & washers etc including painting to all and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Supply and fixing in repair sheet metal enclosure MCB DB double door (Acrylic) single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection, complete all as specified & directed.

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with and including 01 number single pole MCB 20 Amps complete all as specified & directed.

S&F, in replacement, sheet metal enclosure distribution boards IP-54 and IK-09 , double door factory made Vertical TPN 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar complete all as specified and directed.

Supply & fix MCB SPN, 40 Amps, 'B' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply & fix MCB SP, 40 Amps, 'B' series, 240 volts, 50Hz, 10kA complete all as specified & directed.

Supply & fix MCB TPN, 63 Amps, 'C' series, 415 volts, 50Hz, 10kA complete all as specified & directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.0mm thick directly burried in the ground (earth pit not less than 2.25M deep below ground level) with top edge of earth plate not less than 1.50M deep below normal ground level, connected to galvanised iron wire 4mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, 15mm bore GI pipe medium grade including necessary fittings for protection of earthing wire, watering pipe 20mm bore GI medium grade, concrete chamber in PCC (1:4:8) type D-2 using 40 mm grade aggregate, coping shall be in PCC (1:3:6) type C-1 using 20 mm grade aggregate and internal surfaces of concrete chamber shall be given 12mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge (0.63 mm) 8 mesh per linear including 50mm thick cover of RCC (1:2:4) type B-1 using 20mm grade stone aggregate reinforced with 8mm MS deformed bar @ 75 mm C/C both ways, char coal dust and common salt all as shown in electrical plate No. 3 of SSR Part-I (2009) including all necessary excavation & earth work and removal of surplus soil to a distance n. exc 50M and providing connection points with MS/ GI bolts & washers as required and connection from earth test point to earth electrode with same GI earth wire alongwith protection pipe and testing on completion complete all as specified and directed. Note:- GI wire and protection pipe from earth electrode to test point max upto 7.50M shall be deemed to be included in the unit rates as quoted by the contractor.

Supply & fix in repair bell push, single pole one way 5/6 Amps, 240 volts complete all as specified & directed.

Supply and laying or fixing or passing in trenches/ on pole/ through pipes, 1100 volts grade XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured, heavy duty electric cable with stranded aluminium conductor of cross section area 25 sqmm, 4 core including jointing materials such as cable glands & lugs etc and testing on completion complete all as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified & directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified & directed.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth and getting out in soft/ loose soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil exceeding not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Supply & laying of DWC pipe of 65 mm outer dia. and 38 mm innner dia. Including necessary fitting complete all as specified & directed.

Supply & laying of GI steel tubing 50mm bore medium grade galvanised steel tubes with all fittings such as bends, elbow, tees sockets and necessary saddles and clamps and fixed including replacement of old unserviceable fitting complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & laying of GI steel tubing 40mm bore medium grade galvanised steel tubes with all fittings such as bends, elbow, tees sockets and necessary saddles and clamps and fixed including replacement of old unserviceable fitting complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & laying of GI steel tubing 25 mm bore medium grade galvanised steel tubes with all fittings such as bends, elbow, tees sockets and necessary saddles and clamps and fixed including replacement of old unserviceable fitting complete to walls and ceilings or laid in floor complete all as specified & directed.

Supply & laying of GI steel tubing 20 mm bore medium grade galvanised steel tubes with all fittings such as bends, elbow, tees sockets and necessary saddles and clamps and fixed including replacement of old unserviceable fitting complete to walls and ceilings or laid in floor complete all as specified & directed.

Dismantling water tanks of capacity exc 250 litres but n.exc. 500 litres and removal from site to store complete all as specified & directed.

S&F of 500 ltrs capacity rotational moulded polyethylene water storage tank double layered, ISI Marked, (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

Supply & fix, 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod and high dencity plastic ball, screwed for iron pipe or brass ferrule complete all as specified & directed.

Supply & fix in repair 50 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Supply & fix in repair 25 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Supply & fix in repair 20 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Supply and fix in repairs, 20 mm dia Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms) complete all as specified & directed.

M&L for drilling/taping in cast iron/ductile iron water mains ( in position) for branch connection of the internal dia 50 to 20 mm including necessary fitting such as ferrules, nipple short pipe etc complete all as specified & directed.

Schedule of credit amount of Rs. 41,965.00 to be deducted during AOC

M/S A K MUKHERJEE

M/s Om Infracon

Shri kamal traders

charanjeet singh

mandeka constructions

MAYOOKH CONSTRUCTION

M/S Modern builders

TRISHLA CONSTRUCTIONS