REPAIR TO JOINERY, ROOF, FLOORING, CEILING, PLASTERING, SANITARY FITTINGS AND ALLIED SERVICES TO NC PRO UNIT, MED REGT, SAPPERS AND GOLF VIEW SUB GROUP, GE (P), ENGR PARK, B MESS, C MESS AND MES GURUDWARA MD/OTM ACCN UNDER AGE BR-I, IN GE (SOUTH)

Amount

Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15cm thickness (in ground floors), complete all as specified and as directed by Engr-in-Charge.

Demolition of reinforced cement concrete as in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and as directed by Engr-in-Charge.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridges, complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, removing all type of vegetation (like peeple tree etc) scrubbing down with water complete, all as specified and as directed by Engr-in-Charge.

Dismantling wall and ceiling boards (fibre pulp, insulation etc) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and as directed by Engr-in-Charge.

Demolition of brick work or stone masonry built in cement mortar including all quoins arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified and directed by Engr-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed by Engr-in-Charge.

Demolition and breaking up drain pipes, 100mm internal dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, including concrete bedding and haunching complete all as specified and as directed by Engr-in-Charge.

Taking up or down steel tubing of 15 mm bore with connections for cleaning for refixing or removing to store yard/from site, complete all as specified and as directed by Engr-in-Charge.

Taking up or down steel tubing of 20 mm bore with connections for cleaning for refixing or removing to store yard/from site, complete all as specified and as directed by Engr-in-Charge.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6, complete all as specified and as directed by Engr-in-Charge.

Description all as item No 11 above but except bricks.

Brick work with old size sub class 'B' bricks, straight or curved on plan exc 6 m mean radius in half brick thick built in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge.

Walling of random rubble stone masonry uncoursed, with best quality locally available harder stones such as granite, trap, basalt, trap, basalt stone etc, well bonded, bedded and solidly hearted , built in cement mortar 1:6 complete all as specified and as directed.

Description all as per item No 14 here in above but except stones.

15 mm thick rendering in two layers (10+5mm) on fair faces of brick /concrete including facia chhajja etc.surfaces in cement mortar 1:4 and finished even and fair without using extra cement including mixing interal water proofing compund in the proprotion as mentioned in manufacturer's instructions complete all as specified and as directed by Engr-in-Charge. Note : Water proofing compund to be measured and paid for separately as supply only.

10 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6, finish surfaces even and smooth without using extra cement, complete all as specified and as directed by Engr-in-Charge.

10 mm thick rendering on fair faces of brick/concrete surfaces works (chajjas/ ceiling) in cement mortar 1:3 finished even and smooth without using extra cement as in slabs facias, chhajjas and the like, complete all as specified and as directed by Engr-in-Charge.

Providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (n exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints through out the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

75mm thick Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base to floor, complete all as specified and as directed by Engr-in-Charge.

25 mm thick, Plain cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in sub base for laying floor finishes including finishing the surfaces even and rough without using extra cement, complete all as specified and as directed by Engr-in-Charge.

Non skid, coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and as directed by Engr-in-Charge.

Description all as above but in vertical surfaces like skirting, etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering on fair faces of brick/concrete surfaces works in cement mortar 1:3, complete all as specified and as directed by Engr-in-Charge.

Vitrified tiles (double charged) of 10mm thick any colour (area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm) as in floors jointed in cement slurry and pointed in white or coloured cement to match the existing surfaces over and including 15 mm thick screed bedding/ backing layer in CM 1:4, complete all as specified and as directed by Engr-in-Charge.

All as per serial item No. 24 here-in-before but on vertical surfaces as in skirting/dado over and including 10 mm thick screed bedding/ backing layer in CM 1:3, complete all as specified and as directed by Engr-in-Charge.

Heavy duty coloured vitrified tiles double charged (for external application) 10 mm thick Square/rectangular tiles area of each tile not exceeding 0.36 Sqm as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and as directed by Engr-in-Charge. Note : Colour of the tiles shall be as approved by GE.

Description all as per item No 26 above but in skirting/ dado, over and including 10 mm thick backing layer in cement mortar 1:3 finished rough for receiving tiles, complete all as specified and as directed by Engr-in-Charge..

M&L for Pre glazed chequered cement concrete designer tiles 300 x 300 x 20-25mm thick, mixed grey cement (top 5mm of white cement delomite grit and approved colour) with two coats of laquer finish on top of tiles, including corner angles, etc., set and jointed in neat cement slurry and pointed in coloure cement to match the shade of tiles. The tiles shall be manufactured by using rubber moulds on vibrating table not hydraulicaly pressed complete, laid over 20mm thick screed bed in cement mortar 1:4 complete, all as specified and as directed by Engr-in-Charge.

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in shelves/verticle surface, laid over 20mm thick screed bed in cement mortar 1:3 complete, all as specified and as directed by Engr-in-Charge.

Glazed coloured ceramic jointfree/rectified tiles 450mm x 300mm x 7 to 8mm /600 mm x 300 mm x 7 to 8mm thick on vertical surfaces of walls as in dado/skirting etc., set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick screed bedding/ backing layer in CM 1:3, complete all as specified and as directed by Engr-in-Charge.

Mild steel Rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails guides for sliding doors, and vertical posts of pipes sections fixed with angle cleats or other connecting plates, Fe-410-W (Gde - E -250) complete all as specified and as directed by Engr-in-Charge.

4mm thick Cement fibre board (designer ceiling) of size 600mm x 600mm panel conforming to IS 14862 type B category three including GI frame work with size of grid 605mm x 605mm including all accessories and GI suspensions, the fibre sheet should be fire resistant, water resistant, termite resistant, environment friendly & 100% asbestos free, complete all as specified and as directed by Engr-in-Charge.

Pre-painted coloured corrugated profiled Galvalume/Zincalume sheet with min 0.60mm TCT with BTM of 0.55mm thick conforming to IS -513(AZ-150 GSM,Al Zn alloy metallic coating 550MPA yield stress as per AS-1397),as in roof covering/clading to wall fixed with self taping screws, colour/exterior coat of silicon modified polyster/ BHP x RW paint system 20 micron top coat applied over 5 micron primer and a micron polyster back coat applied over 5 micron primer,all fixed with galvanised self drilling self tapping fastener(12-14x55 with EPDM seals), complete all as specified and directed

Pre-painted coloured plain steel profiled Galvalume/Zincalume sheet with Min 0.60 mm TCT with BTM of 0.55mm thick conforming to IS-513(AZ-150 GSM, Al Zn alloy metallic coating 550 MPA yield stress as per AS-1397) as roof ridge colour/exterior coat of silicon modified polyster/BHPxRW paint system 20 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer ,all fixed with Galvanised self drilling self-tapping fastener (12-14x55 with EPDM seals) complete all as specified and directed.

6mm thick asbestos cement, corrugated or semi-corrugated sheets fixed with fixed with L-type or J-type or cranked hook bolts and washers, in roofs, walls etc. with complete all as specified and directed. (ISI Marked)

Description all as per item No 35 here in above but except sheet

Asbestos cement two piece adjustable serrated ridge for corrugated or semi corrugated sheets 6mm thick fixed with L-type or J-type or cranked hook bolts and washers, in roofs, walls etc. with complete all as specified and directed.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 20mm thick screeding in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately) and applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric APP (Atactic Polypropylene) Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.5 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm and applying two coats of aluminium paint on roof complete all as specified and as directed by Engr-in-Charge. Note :- Water proofing treatment will be done by manufacturer of APP membrane or through their authorised specialized agency which will further have to give a five years warranty for rectification of any defect if incurred at a later stage, otherwise no payment shall be made to the contractor if water proofing treatment is executed otherwise.

Providing cement concrete in steps, seismic and other similar bands, parapets and railings up to 60 cm in hieght, coping, kneeless apex stones , bed plates, kerbs not provided for including weathering, slightly rounded or chamfered angles all as directed, 1:2:4 mix type B-0 complete all as specified.

Supply only liquid water proofing compound, complete all as specified & directed by Engr-in-Charge.

Drapery rod (MS conduit) of dia not less than 25 mm having a corrugated virgin PVC extrusion on it & finials of approved shade with standard MS powder coated/ brackets including end caps, fixed to walls with rawl plugs and steel screws, complete all as specified and as directed by Engr-in-Charge.

110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed by Engr-in- Charge.

110 mm bore PVC SWR bends any radius with acess door and fixed solvent etc complete all specified and as Directed (ISI Marked)

15 mm bore steel water tubing medium grade galvanised with and including all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed by Engr-in-Charge.

20 mm bore steel water tubing medium grade galvanised with and including all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tank , three layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 500 litres each including all accessories (i.e GI nipples and Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of bore 20mm/25mm (Minimum weight 210 gram) etc), incl dismantling existing water tanks, complete all as specified and as directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tank , two layers, ISI marked (cylinderical vertical with closed top) hoisted with Threaded Cap and fixed in position all as specified in SSR Part-I of Capacity 1000 litres each including all accessories (i.e GI nipples and Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of bore 20mm/25mm (Minimum weight 210 gram) etc), incl dismantling existing water tanks, complete all as specified and as directed by Engr-in-Charge.

Vitreous China wash down water closet pan and seat cover (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including P or S trap and including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, including connection to drain pipe (or out going pipe) and to flushing pipe, antisyphonage pipe, etc. including cast iron 'P' or 'S' trap for 100mm bore of pipe, fixed in repairs complete all as specified and as directed by Engr-in-Charge.

Vitreous china water closet, 'Orissa pattern, including lime concrete bedding, size 580 x 440 mm white with integral foot rests excluding flushing cistern and flush pipe but including cast iron 'P' trap, CI connection , anti syphonage pipe etc. complete fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Water closet cloured (Single piece) of size 850x360x720mm trap distance (mm) S-300, ZPS-WHT-1024 UF soft close seat cover set fixed in repairs complete all as specified.

15mm bore centre hole basin mixer without Popup waste system with 450mm long braided PVC hoses, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Bib taps , cast copper alloy, chromium plated, fancy type, screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm fixing in repair, complete all as specified and as directed by Engr-in-Charge

Stop valves/Angle valve, fancy type chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Glass shelf with chromium plated guard rails,fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Soap dish holder, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

CP tubular towel rail, 20mm dia, D type, 60cm long between flanges aluminium anodized, fixed with rawl plugs, complete all as specified and as directed by Engr-in-Charge.

Toilet paper holder, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Corner glass shelf with brackets and brass chromium plated guard rails, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Bib taps , cast copper alloy, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule for bore of pipe 15 mm fixing in repair, complete all as specified and as directed by Engr-in-Charge

Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms).complete all as directed and specified.

Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm, fixing in repair, complete all as specified and as direceted by Engr-in-Charge.

Stop valves, fancy type, chromium plated, cast copper alloy, with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm fixing in repair , all as specified.

Angle valves, fancy type chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm with adjustable flanges, fixed in repair, complete all as specified and as directed by Engr-in-Charge.

Brass Chromium plated over head shower rose of dia 125mm with swivel joint fixed to pipe or union of 15mm bore, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing in repair ball brass valves of size 20mm bore dia, high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including necessary fitting as reqd at site complete all as specified and directed by Engr-in-charge.

75mm Cast iron floor traps with grating including jointing to waste pipe fixed cncrete type B1 (1:2:4) fixed in repairs, complete all as specified and as directed.(ISI Mark)

75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and as directed by Engr-in- Charge.

100 mm bore cast Iron P or S trap, fixed in repairs, complete all as specified and as directed by Engr-in-Charge.

Vitreous china urinal, half stall type white incl CP Spray Nozzale including PVC waste pipe, providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement ,(Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), fixed in repair, complete all as specified.

10 ltr capacity PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with twin flush provision, complete all as specified and as directed by Engr-in-Charge.

S&F Viterous china wash basin, white flat back size 580 x 450mm including waste coupling CP 32mm dia chain and plug and porcelan stopper and CI brackets of iron 65 x 65 x 6mm embedded in PCC block with PCC 1:2:4 type B-1 and PVC waste pipe 32mm dia & CP getting with holes, complete all as specified and as directed by Engr-in-Charge.

Applying two coat of oil bound distemper over and including a coat of primer including preparation of newly plastered surfaces of wall.

Preparing newly plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and as directed by Engr-in-Charge.

Preparation new surfaces plastered or unplastered and applying three coats of white wash on ceiling all as specified

Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide/zink chrome primer complete, complete all as specified and as directed by Engr-in-Charge.

Preparation of new wooden or wood based surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer, complete all as specified and as directed by Engr-in-Charge.

RCC M-25 Design mix, (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed by Engr-in-Charge.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc to obtain rough flat finished surface of concrete complete all as specified and as directed.

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and includingMS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.), complete all as specified and directed by Engineer-in Charge.

Description all as per item No 83 above but area exceeding 1.50 square metre and not exceeding 4 square metre each.

Taking down shutters of any description exceeding 1.00 square metre and not exceeding 2.00 square metre each complete, all as specified and directed by Engineer-in charge.

Taking down shutters of any descriptions area not exceeding 1 square metre each complete all as specified and as directed by Engr-in-Charge.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing, complete all as specified and as directed by Engr-in-Charge.

Powder coated (not less than 50 micron) aluminium frames for door/ windows/ ventilators of approved design with one or more rebated including jointing cleats with all fixing arrangement in repair, complete all as specified and directed by Engr-in-Charge.

S&F Aluminium window / ventilator air tight of powder coated frame made of size 100mm x 45mm of section thickness- 1.50mm thick and shutter stiles made of section 80mm x 45mm x 1.5mm thick with or without rebates, with 5.5mm thick tinted glass fixed with aluminium beads, including GAUZED AND GLACED SHUTTER, necessary jointing cleats/anodised aluminium fillets/aluminium glazing clips with rubber gasket, with aluminium fittings such as aluminium butt hinges 100mm long 03 Nos, aluminium anodised tower bolt 100mm long 02 Nos, aluminium anodised bow handles 100mm 01 No, aluminium hook and eye 150mm 01 No, in each shutter including aluminium grill of 5 to 6 dia, size of mesh not exc 7.5cm in either direction, as approved by GE, complete all as specified. Note:- All fitting shall be of ISI marked except cleats ) sizes of each shutter shall be as per site requirement all as directed and specified

Powder coated aluminium Deco grill DG 202 pattern with apperture of size 60x45mm securing with suitable aluminium channel to frame complete all as specified as directed by Engr-In-Charge.

35 mm thick, factory made, 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 12 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, complete all as specified and directed by Engr in Charge.

35mm thick, factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete, all as specified and directed by Engr in Charge.

Factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site complete all as specified.

Mild steel, 150 mm, ordinary rat tail rod pattern door spring including roller and roller plate complete all as specified.

12mm thick frameless Swing Toughened Glass Door ( single / double shutter ) with etched design openable in both direction and including fixing clips , glass fins , stainless steel handles length exceeding 600mm 02 Nos on each shutter incl floor spring , floor locks and all accessories complete all as specified and directed by Engineer - in - charge . Note : Door size as per site requirement

35mm thick, factory made 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b); supplied and fitted to chowkats complete, all as specified and directed by Engr in Charge.

35 mm thick flush shutters,solid core construction,with block board core and ply wood face pannels and one face is covered with decorative face veneer with lipping/frame to match all as specified.

S&F powder coated door air tight of anodised frame made of size 100 mm x 45mm of section thickness -1.50 mm thick with one or more rebates including jointing cleats etc for fixing aluminium anodised door shutter fully panelled (two no of panels on each shutter) with 5.5 mm thick tinted glass as in panels shutter rail made of 80mm x45 mm of sheet thickness 1.50 mm (Top and bottom rails and stiles) single /double leaf side hung type including necessary jointing cleats anodised aluminium fillets/ glazing clips with rubber gasket with aluminium fittings such as aluminium anodised tower bolt 200mm long 03 No for each door, aluminium anodised bow handles 150 mm 'D type 02 nos for each shutter, mortice locks 6 lever one on each door, door shutter mounted on bottom double action floor spring hydrailically regulated made up of 1.25mm thick aluminium alloy sheet foundation box , main body with stainless steel cover, governing mild steel heavy duty and door shutter top mounted on aluminium alloy pivot. -01 No on each shutter, bottom and floor stoppers, Complete all as specified. Note : All fitting shall be of ISI marked except cleats) sizes of each door shall be as per site requirement all as directed and specified.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other part made of mild steel heavy duly and fixed repair including taking down aluminium shutter and refixing in replacement of pivat complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium (Die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 68 kg complete all as specified and as directed by Engr-in-Charge. (ISI Mark)

18/19mm thick Prelaminated particle board, termite proof, chemically well pressed, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, as in kitchen cabinet, cub boards, etc including 6mm thick teak wood beading all around complete all as specified and as directed by Engr-in-Charge.

12mm thick plywood, grade BWP, type BB fixed with screws to timber/steel frame work complete all as specified and as directed by Engr-in-Charge.

0.9 mm thick decorative choice of lamination type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive 1.5 mm thick, complete all as specified and directed.

1.50 mm thick decorative choice of lamination type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive 1.5 mm thick, complete all as specified and directed.

18/19mm thick Prelaminated particle board, termit proof, chemically well pressed, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, as in kitchen cabinet, cub boards, etc including 6mm thick teak wood beading all around complete all as specified and as directed by Engr-in-Charge.

Description all as above srl item No.105 but 12mm thick.

Continuous ( piano) hinges mild steel ,bright finish or electrogalvanised , width of flap (when open ) 30mm , complete all as specified.

40 mm dia cupboard knobs fixed with nut, screw and washer of mild steel bright finish complete all as specified.

100mm size hasp and staple safty type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screw complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame/wooden frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed by Engr-in-Charge.

3mm thick Sheet glass, ordinary quality and glazing with oil putty in square or rectangle, area n exc 0.5 sqm in each pane, complete all as specified and as directed by Engr-in-Charge.

3 mm thick figured glass, pin head type, ordinary quality and glazing with oil putty in square or rectangle, area n exc 0.5 sqm in each pane complete all as specified and as directed by Engr-in-Charge.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete, all as specified. (ISI Mark)

S&F as in repairs Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete, all as specified. (ISI Mark)

Butt hinges 100mm size, extruded aluminium alloy, complete all as specified and directed. (ISI Mark)

Butt hinges 125mm size, extruded aluminium alloy, complete all as specified and directed. (ISI Mark)

300 mm long aluminium alloy, anodised, sliding door bolt (ISI Marked) with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed by Engr-in-Charge.

200mm long, aluminium anodised, barrel tower bolts (ISI Marked) of extruded section and fixed, complete all as specified and directed by Engr-in- Charge.

150mm long, aluminium anodised, barrel tower bolts (ISI Marked) of extruded section and fixed, complete all as specified and directed by Engr-in- Charge.

75mm long, aluminium anodised, barrel tower bolts (ISI Marked) of extruded section and fixed, complete all as specified and directed by Engr-in- Charge.

100 mm aluminium handles, extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. (ISI Mark)

75 mm aluminium handles, extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. (ISI Mark)

150/200 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete, all as specified. (ISI Mark)

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, 140mm overall length of cover plate complete all as specified and directed. (ISI Mark)

Supply and Fixing brass mortice lock four levers vertical type size 100mm or above complete all as specified and as directed by Engr-in-Charge.

Pressed steel frames for doors, made out of 1.25 mm thick MS sheet, with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 mm x 60 mm, including one shop coat of red oxide zinc chrome primer, including filling voids with PCC type C-0 complete all as specified and as directed by Engr-in-Charge.

Mild Steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and as directed by Engr-in-Charge.

Rolled section/tubular sections as in main and cross beams, purlins, rafters,posts where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. conforming to Fe-410-W complete all as specified and as directed by Engr-in-Charge.

Preparation of old steel and iron surfaces exceeding 10 cm width or girth and applying one coat of synthetic enamel paint , complete all as specified and as directed by Engr-in-Charge.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all specified and as directed. Notye : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

Description all as per item above No 130 but without glazing bar complete all as specified and as directed.

Providing and injecting along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per running metre including drilling and plugging holes etc. in apron. complete all as specified and as directed by Engr-in-Charge. Note : The treatment work shall be carried through authorised agency having valid license and member of IPCA. Certificate for the same and warranty shall have to be furnished before claiming payment.

Providing and injecting Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed by Engr-in-Charge. Note : The treatment work shall be carried through authorised agency having valid license and member of IPCA. Certificate for the same and warranty shall have to be furnished before claiming payment.

Sinks made of stainless steel with draining board, made out of 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar including fixing cantilever brackets connecting union to pipe and 32mm dia GI pipe duly painted upto Nihani Trap or Floor trap complete as directed at site, overall size 915mmx460mm bowl size 410mm x 330mm x160mm, in repair complete all as specified.

0.63 mm thick ,Plate rack made of stainless steel, 785x760 x 250mm including fixing as per manufacturers instruction complete all as specified. Note : weight not less than 5 Kilogram.

Aluminium sheeting, Alloy 31000 H4l, 0.56mm thick plain, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and as directed by Engr-in-Charge.

vmd traders

SINGH CONST CO

RAMAN CONSTRUCTION CO