Repair/Replacement Pipe Lines Control Valves Pumping System and Switchgear Installed at Distribution area under AOR of GE (U) Udhampur.

Amount

Decoupling, disconnecting suction line and discharge line taking down from foundation, dismounting from base channels strip opening all parts, derusting, cleaning, overhualing comprising of repairs/replacement of unserviceable parts of pump sets and taking to workshop (if reqd) for repairs. Reassembling of pump set mounting and fixing on base channel, recoupling of suction & discharge line realignment commissioning and testing in respect of centrifugal/multistage pump of capacity 50 to 60 HP, , complete all as specified and directed by Engr-in-Charge. Note :(i) Loading/unloading & transportation charges shall be deemed included in the quoted rates. (ii) S&F of parts shall be measured and paid separately under respective item of sch A.

All as per Ser item No 1.01 here-in-before but capacity 30 to 40 HP, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 1.01 here-in-before but capacity 15 to 20 HP, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 1.01 here-in-before but capacity 7.5 to 10 HP, complete all as specified and directed by Engr-in-Charge.

S&F New parts for single/multistage pumps of capacity 50 to 60 HP as per manufacturer's composition of existing make of pump as below , complete all as specified and directed by Engr-in-Charge.

Impeller, MOC: CI.

Pump shaft stainless steel shaft complete with check nut and keys

Tyre coupling/star coupling

Star /Tyre coupler made of steel

Gland cup

Shaft sleeves

Bearing housing

Casing housing

S&F New parts for single/multistage pump of capacity 30 to 40 HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engr-in-Charge.

Impeller, MOC: CI

Pump shaft stainless steel shaft complete with check nut and keys

Tyre coupling/star coupling

Star coupler made of steel

Gland cup

Shaft sleeves

Bearing housing

Casing housing

S&F New parts for single/multistage pump of capacity 15 to 20 HP as per manufacturer's composition of existing make of pump as below all, complete all as specified and directed by Engr-in-Charge.

Impeller, MOC: CI

Pump shaft stainless steel shaft complete with check nut and keys

Tyre coupling/star coupling

Star /Tyre coupler made of steel

Gland cup

Shaft sleeves

Bearing housing

Casing housing

S&F New parts for single/multistage pump of capacity 7.5 to 10 HP as per manufacturer's composition of existing make of pump as below, complete all as specified and directed by Engr-in-Charge.

Impeller, MOC: CI

Pump shaft stainless steel shaft complete with check nut and keys

Tyre coupling/star coupling

Star /Tyre coupler made of steel

Gland cup

Shaft sleeves

Bearing housing

Casing housing

Pump seal

Lath/Mchining works of any type at workshop required for balancing of impller/for fixing of new parts to existing shfts required for proper setting and smooth functioning to achieve desired discharge of the pump for 50 to 60 HP pump, complete all as specified and as directed by Engr-in-charge.

All as per Srl item No. 9.00 here-in-before but capacity of 30 to 40 HP motor, complete all as specified and directed by Engr-in-Charge.

All as per Srl item No.9.00 here-in-before but capacity of 15 to 20 HP motor, complete all as specified and directed by Engr-in-Charge.

All as per Srl item No.9.00 here-in-before but capacity of 7.5 to 10 HP motor, complete all as specified and directed by Engr-in-Charge.

Disconnecting electric connection of 50 to 60 HP motor, removing the UNSV motor from existing place by unscrewing the foundation bolts and nuts decoupling from the pump, setting aside and transporting to workshop for repairs including dismantling the motor,cutting/taking out burnt winding of stator, rotor, cleaning the slots, transporting back after repair/winding & re-assembling the same complete all as directed by Engineer-in-Charge. Note: (a) Rewinding of motor will be measured and paid separately under relevent item. (b) The rates quoted shall be deemed to include the cost of loading/unloading, transportation, grease, nuts, bolts and washers of any size and shape as required at site and refixing of serviceable motor duly functional and testing complete at its existing location/position complete all as specified and directed.

All as per Srl item No. 13.01 here-in-before but capacity 30 to 40 HP motor, complete all as specified and directed by Engr-in-Charge.

All as per Srl item No. 13.01 here-in-before but capacity of 15 to 20 HP motor, complete all as specified and directed by Engr-in-Charge.

All as per Srl item No. 13.01 here-in-before but capacity of of 7.5 to 10 HP motor, complete all as specified and directed by Engr-in-Charge.

Removing the burnt out winding from the rotor and stator, cleaning the slots, providing high quality of class'B' paper insulation inside the slots, rewinding the motor of capacity 60/50/40/30/20/15/12/10/7.5 HP with super enamel copper wire of same size and guage as per existing rapping up with high quality cotton tape and varnising with super quality oil including drying upto desired temperature and desired time, complete all as specified and directed by Engr-in-Charge. Note:- Cost of labour for winding deemed to be included in the rate quoted Make : Atlas/Devi Dayal or equivalent make.

Supply and fixing in repair/replacement of 2 to 3 HP pumpset (including motor) by taking out from foundation, dismounting from base channels, strip opening all parts, derusting, cleaning, overhualing, etc for complete repair/ replacement of spare parts such as impeller, shaft, winding, bearings, coupling, body, etc and after repair/ replacement, reassembling of pumpset mounting and fixing on base channel, recoupling of suction & discharge line, realignment, commissioning and testing complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair/replacement of 0.5 to 1 HP pumpset (including motor) by taking out from foundation, dismounting from base channels, strip opening all parts, derusting, cleaning, overhualing, etc for complete repair/ replacement of spare parts such as impeller, shaft, winding, bearings, coupling, body, etc and after repair/ replacement, reassembling of pumpset mounting and fixing on base channel, recoupling of suction & discharge line, realignment, commissioning and testing complete all as specified and directed by Engr-in-Charge.

M&L for repair of booster pressure pumpset of cap 0.25 HP to 1 HP by taking out from foundation, dismounting from base channels, strip opening all parts, derusting, cleaning, overhualing, etc for complete repair, reassembling of pumpset mounting and fixing on base channel, recoupling of suction & discharge line, realignment, commissioning and testing complete all as specified and directed by Engr-in-Charge.

Supply and fixing of relay switch for booster pressure pump of capacity 0.25 HP to 1 HP pumpset complete all as specified and directed by Engr-in-Charge.

M&L for dismantling following spare parts of submersible pump and motor of cap 1 to 5 HP and separating the unserviceable parts cleaning the serviceable parts, re-metalling machinery polishing and re-assembling including replacement of old parts and necessary painting, complete all as specified and directed by Engr-in-Charge. Note:- Old unserviceable parts replaced will be measured and paid separately.

M&L for Impeller for submersible pump set and motor, complete all as specified and directed by Engineer-In-Charge.

M&L for Bush for impeller for submersible pump set and motor, complete all as specified and directed by Engineer-In-Charge.

S&F of Pump bearing No. 6307 C3 Make:-SKF/NBC/NRB or equivalent make

S&F of Pump bearing No. 6308 2RS1/C3 Make:-SKF/NBC/NRB or equivalent make

S&F of Motor bearing No. 6311. Make:-SKF/NBC/NRB or equivalent make

S&F of Pump bearing No. 7311/ NU 411M Make:-SKF/NBC/NRB or equivalent make

S&F in replacement of ON load change over switch 320 Amps, 415 volts 4 pole with stainless steel enclosure inculding taking down the old existing change over switch , complete all as specified and directed by Engr-in-Charge. Make : Havells/ L&T/ ABB

All as per Ser item No 27.00 here-in-before but of size 200 Amps, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 27.00 here-in-before but of size 100 Amps, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of OFF load change over switch 320 Amps, 415 volts 4 pole with stainless steel enclosure inculding taking down the old existing change over switch, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 30.00 here-in-before but of size 200 Amps, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 30.00 here-in-before but of size 100 Amps, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 30.00 here-in-before but of size 63 Amps, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of load line MCCB 320/350 Amps 4 pole 415 volts with adjustable thermal and fixed magnetic setting of breaking capacity 35/36 KA,Ics=100% Icu conforming to IEC - 60947-2 including taking down the old existing MCCB, , complete all as specified and directed by Engr-in-Charge. Make : L&T/Legrand/ABB/Siemens

All as per Ser item No 34.00 here-in-before but of size 200 Amps, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 34.00 here-in-before but of size 160 Amps, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 34.00 here-in-before but of size 125 Amps, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 34.00 here-in-before but of size 100 Amps, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 34.00 here-in-before but of size 80 Amps, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of power contactor 3 pole with AC coil AC-3 duty rating at 415 Volts 50 Hz, frame size1 suitable for 60 HP centrifugal pump set as per Havells cat part No. IHPHA100400* , complete all as specified and directed by Engr-in-Charge.

M&L in replacement of PVC insulated heavy duty industrial cables single core copper conductor(flexible) PVC insulated cable 1100 volt nominal area of conductor 50 sqmm inculding taking down existing old unserviceable cable of, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 41.00 here-in-before but of size 25 sqmm, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 41.00 here-in-before but of size 16 sqmm, complete all as specified and directed by Engr-in-Charge.

M&L for copper thimble suitable for 50 Sqmm single core copper cable including taking down the existing unserviceable one complete, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 44.00 here-in-before but of size 25 sqmm, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 44.00 here-in-before but of size 16 sqmm, complete all as specified and directed by Engr-in-Charge.

M&L for aluminium thimble of 150 sqmm size for cables, complete all as specified and directed by Engr-in-Charge.

M&L for aluminium thimble of 95 sqmm size for cables, complete all as specified and directed by Engr-in-Charge.

S&F capacitor upto 40 mfd for motor completed, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of DOL starter in sheet steel enclosure single phase 220 volts, 50 Hz for motor of capacity 5 HP as per Havells cat part No. IHHDOLLA*E completed all as specified and directed by Engr-in-Charge. Make-Havells/Legrand/L&T

Supply and laying DWC (Double wall corruguated) pipe 40/32 mm conforming to IS-14930/ IS-16205 for protection of earth strip/cable including necessary snap fit coupler reqd for fixing complete all as specified and directed by Engr-in-charge

Supply and laying DWC (Double wall corruguated) pipe 50/41 mm conforming to IS-14930/ IS-16205 for protection of earth strip/cable including necessary snap fit coupler reqd for fixing complete all as specified and directed by Engr-in-charge

Supply and laying DWC (Double wall corruguated) pipe 75/63 mm conforming to IS-14930/ IS-16205 for protection of earth strip/cable including necessary snap fit coupler reqd for fixing complete all as specified and directed by Engr-in-charge

Supply and fixing in replacement of terminal boxes suitable for 60/50 HP motor as per existing specification including taking down the old existing terminal box, complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of terminal boxes suitable for 40/30/20 HP motor as per existing specification including taking down the old existing terminal box, complete all as specified and directed by Engr-in-Charge.

M & L for painting of Header/ pump and motor, frame, pipe line including surface preparation by scrapping with emery paper and painting two coats of synthetic enamel paint over one coat of red oxide primer of existing colour of approved make to the satisfaction of Engr in Charge, complete all as specified and directed by Engr-in-Charge.

M&L for writing with brush about the machinery installed in different instalations such as Cap, discharge,MES No,Year of installation and head of the machinery on the wall in front of the pump motor with black paint including removing the existing paint with help of grinder, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of gland packing type 3 of size 8 mm made of asbestos grip with silicon, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 58.00 here-in- before but of size 10 mm, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 58.00 here-in- before but of size 16 mm, complete all as specified and directed by Engr-in-Charge.

Supply and laying in replacement of synthetic rubber insulated mats 10 mm thick for insulation purpose suitable for electrical shock safety of sizes 2 m x 1.2 m, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of MS stud bolts of existing size suitable for pumps and motors of various capacity installed at installations, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of grouting nuts and bolts of existing size suitable for pumps and motors foundation of various capacity installed at installations, complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete type B-2, 1:2:4 (40mm graded aggregate) as in sub base filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

M&L for cement concrete in foundations, type E-2, 1:5:10 (40mm graded aggregate) as in filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repacement of Cast iron Foot valve Flanged with strainer of 150 mm dia including all types of fittings conforming to IS specification, complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repacement of Cast iron Foot valve Flanged with strainer of 100 mm dia including all types of fittings conforming to IS specification, complete all as specified and directed by Engr-in-Charge.

Supply only lithium base grease AP3 in 20 Kg pack suitable for application to ball bearing with operating temperature 30 to 120 degree celsius drop point 174 degree celsius, colour light fawn, complete all as specified and directed by Engr-in-Charge.

Supply only cotton waste coloured Grade "A' for cleaning rags in 25 Kgs bag, complete all as specified and directed by Engr-in-Charge.

M&L for painting complete outer surrounding of over head tank in Tri-colour including writing of "SAVE WATER, SAVE LIFE" in blue colour on centre white colour, complete all as specified and directed by Engr-in-Charge.

Supply only Chlorine testing kit to check the chlorine at installations, complete all as specified and directed by Engr-in-Charge.

Supply and laying, jointing and testing of XLPE insulated, armoured heavy duty electric cable with aluminium conductor 1100 volts grade of size 95 sqmm 3.5 core laid in trenches,ducts, pipes, , complete all as specified and directed by Engr-in-Charge.

Earthing of machinery/equipment Installed at power house/substation with galvanised steel earth plate electrode 600 mm × 600 mm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron strip 32× 6mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion, , complete all as specified and directed by Engr-in-Charge.

Opening, maintenance and general servicing of Servo voltage stablizers of different makes of 100 KVA including removal of sludge from disserstate coils, buck boost transformers, tightening of all nut bolts, cleaning of stablizers coils, checking and servicing of servo mechanism, gear synchronising system, automatic voltage regulator circuits and other allied electrical components complete all as specified and directed by Engr-in-charge. Note : Rate quoted by contractor is inclusive of following items:- (a) Servo motor with RC network having torque upto 10 kg/cm (b) Electronic cntrol card for automatic voltage regulation (c)Transformer oil -35 ltrs (d) Voltmeter 0-500 volt capacity (e) Ammeter CT Operated (f) Items like carbon bush, push buttons auto/manual/micro press switch, indicator lamps, etc

M&L for construction of stone masonary valve pit size 1 mtr x 1 mtr x .5 mtr(internal dimention) including stone work, PCC work and MS sheet work as per site requirment, complete all as specified and directed by Engr-in-charge

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth,foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. and taking out/laying of pipe lines of soft/loose soil, complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers, each layer not exceeding 25cm thick after pipes have been laid and tested, complete all as specified and directed by Engr-in-Charge.

Removing excavated material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed by Engr-in-Charge.

Taking up or down old unseviceable GI pipe of size 150 mm dia including all fittings, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 80.00 here-in-before but of 100 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 80.00 here-in-before but of 80 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 80.00 here-in-before but of 50 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 80.00 here-in-before but of 40 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 80.00 here-in-before but of 25 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 80.00 here-in-before but of 20 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 80.00 here-in-before but of 15 mm dia, complete all as specified and directed by Engr-in-Charge.

Supply & fixing GI pipes of size 150 mm dia, medium grade, galvanized with all fitting such as bends, tees, nipples, union and sockets, clamps etc laid in trenches, under floor/walls etc complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 88.00 here-in-before but of 100 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 88.00 here-in-before but of 80 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 88.00 here-in-before but of 50 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 88.00 here-in-before but of 40 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 88.00 here-in-before but of 25 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 88.00 here-in-before but of 20 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 88.00 here-in-before but of 15 mm dia, complete all as specified and directed by Engr-in-Charge.

Refixing GI/CI pipe obtained from Item No. 88.00 above and connections in new or old position (walls, trenches, ceiling and floors etc) of size 150 mm dia complete including main branch connections, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 96.00 here-in-before but of 100 mm dia obtained from item No. 89.00, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 96.00 here-in-before but of 80 mm dia obtained from item No. 90.00, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 96.00 here-in-before but of 50 mm dia obtained from item No. 91.00, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 96.00 here-in-before but of 40 mm dia obtained from item No. 92.00, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 96.00 here-in-before but of 25 mm dia obtained from item No. 93.00, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 96.00 here-in-before but of 20 mm dia obtained from item No. 94.00, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 96.00 here-in-before but of 15 mm dia obtained from item No. 95.00, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement cast iron sluice valve suitable of size 300 mm (PN 1.6) ISI Marked with iron wheel head both end flanged, non rising type and jointing with the rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers including taking down the old existing, complete all as specified and directed by Engr-in-Charge. .

All as per Ser item No 104.00 here-in-before but of size 200 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 104.00 here-in-before but of size 150 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 104.00 here-in-before but of size 100 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 104.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of cast iron non return valve suitable for 150 mm bore pipe heavy duty both end flanged of pressure rating PN 1.6 as per IS:5312 and jointing with the rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers including taking down the old existing, Complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 109.00 here-in-before but of size 100 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 109.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engr-in-Charge.

Supply and fix Foot Valve of size 50 mm dia, complete all as specified and directed by Engr-in-Charge.

Supply and fix Foot Valve of size 40 mm dia, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of cast iron air release valve with two air outlets of size 100 mm dia as per IS 14845 including all jointing materials like high pressure rubber gasket nuts, bolts, washers with arrangement for fixing, including taking down complete, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 114.00 here-in-before but of size 80 mm dia, complete all as specified and directed by Engr-in-Charge.

Repair to old sluice valve of size 300 mm dia for check nut, spindle, refacing, regrinding & refixing at its original location including cleaning, repacking stuffing box of sluice valve & spindle including fixing & testing, , complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 116.00 here-in-before but of 200 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 116.00 here-in-before but of 150 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 116.00 here-in-before but of 100 mm dia, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 116.00 here-in-before but of 80 mm dia, complete all as specified and directed by Engr-in-Charge.

M&L for repair to leaking run lead joints in CI/DI spigot and socket end pipe line of 100 to 150 mm bore by providing new lead ,using good quality spun yarn, including necessary excavation, returning filling in trenches in any type of soil,bailing out water, and at any depth, complete all as specified and directed by Engr-in-Charge. Note:- (i) Contractor fully responsible for necessory excavation for jointing work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate. (ii) Required extra fittings/pipe will be measured and paid separately.

Supply and fixing in replacement of LED multicolour (Colour changing) underwater lights of capacity 18 watt 12 Volt with IP-68 protection, complete all as specified and directed by Engr-in-Charge. Make : Cravin or equivalent as approved by GE.

Supply and fixing control module box included with MCB's for controlling 18 watt LED lights, , complete all as specified and directed by Engr-in-Charge. Make : Cravin or equivalent as approved by GE.

M&L for repair to leaking GI pipe line of size 50 mm to 80 mm bore by providing necessary fitting such as socket, Tee, Elbow,etc including necessary excavation, returning filling in trenches in any type of soil,bailing out water, and any depth, complete all as specified and directed by Engr-in-Charge. Note:- (i) Contractor fully responsible for necessory excavation for jointing work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate. (ii) Required extra pipe will be measured and paid separately.

All as per Ser item No 124.00 here-in-before but of size 20 mm to 40 mm bore pipe, , complete all as specified and directed by Engr-in-Charge.

Material and labour for repair to leaking flanged/circular welding joints of 100 to 200 mm bore MS/GI pipe line by providing rubber or fiber board gasket, new flanges if required at site, nut bolts, washers and welding works where required etc, including necessary excavation, returning filling in trenches in any type of soil, bailing out water, and any depth, complete all as specified and directed by Engr-in-Charge. Note:- (i) Contractor fully responsible for necessory excavation for jointing work required T&P equipment, mechanical excavation work and man power at site requirement with making good disturbed surfaces of road/wall/floor etc and matching with existing surface included quoted rate. (ii) Required extra pipe will be measured and paid separately..

All as per Ser item No 126.00 here-in-before but of dia 250 to 300 mm bore pipe, complete all as specified and directed by Engr-in-Charge.

M&L for cutting of existing road for crossing of MS/DI/CI/GI pipes for laying of any size pipes including necessary exacavation and earth work including repairing the same as per existing, complete all as specified and directed by Engr-in-Charge.

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) cement concrete in as in foundation filling of pole & stay, , complete all as specified and directed by Engr-in-Charge.

M&L for Premix ready mix road repair patching compound for instant road repair manufactured with a blend of bitumen, aggregates and high grade polymer to ensure immediate bonding with existing surface available in bag of 25 Kg, , complete all as specified and directed by Engr-in-Charge.

Supply of Copper Sulphate for swimming pool water cleaning and colouring, , complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of LED underwater lights of cap not less than 34 watt and 12 V DC supply, IP-68 protection of external body size 225 mm dia with independent control gear, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of driver of LED underwater lights of cap 34 watt and 12 V DC supply, protection of external body size 225 mm dia with independent control gear, , complete all as specified and directed by Engr-in-Charge.

Supply and fix water proof fountain light of capacity 10 watt having warm light output, complete all as specified and directed by Engr-in-Charge.

Supply and fixing the nipple brass nozzle as per sample including removal of existing unsv one, complete all as specified and directed by Engr-in-Charge.

Supply & Laying multicore PVC insulated and FR-LHS PVC round sheatehed, copper conductor(flexible) industrial cable 1100 volt grade confirming to Is 694 , 1.5 sqmm 1 core including suitable size PVC conduit laid, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 136.00 here-in-before but of size 2.5 sqmm 1 core, , complete all as specified and directed by Engr-in-Charge.

Supply & laying of flexible pipe of 15/20 mm dia used for wiring purpose, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of PVC Butterfly valve of of size 140 mm dia PN 16, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of PVC Foot valve of of size 110 mm dia PN 16, complete all as specified and directed by Engr-in-Charge.

Repair to leakage of 110 to 160 mm PVC pipe including all necessary fitting such as Tee, Socket, jointing material, etc, complete all as specified and directed by Engr-in-Charge.

Supply & fixing PVC pipe of size 110 mm dia class 3 (as per existing) including all necessary fitting such as bends, Socket, jointing material, etc complete all as specified and directed by Engr-in-Charge.

Supply & fixing PVC pipe of size 140 mm dia class 3 (as per existing) including all necessary fitting such as bends, Socket, jointing material, etc complete all as specified and directed by Engr-in-Charge.

Supply & fixing PVC pipe of size 160 mm dia class 3 (as per existing) including all necessary fitting such as bends, Socket, jointing material, etc complete all as specified and directed by Engr-in-Charge.

S&F cast iron fittings for spigot and socket ends for pressure pipe for water mains such as bends, tapers, tee pieces single branch, cross collar, caps and plugs suitable for upto 150 mm bore, all specifications as per IS-1538 (Pt-1 to 23)-1976, complete all as specified and directed by Engr-in-Charge.

Supply fabrication and fixing MS joints like Flanged, bends, Tee, Tapers, collars, elbow, tail piece (any type) caps, plugs for 80 mm to 300 mm bore pipe, complete all as specified and directed by Engr-in-Charge.

S&F of Gun metal, globe or gate valves, 80mm dia , heavy duty, with iron wheel head, screwed both ends (ISI marked), complete all as specified & directed by Engr-in-Charge.

S&F of Gun-metal, globe or gate valves, 50 mm dia , heavy duty, with iron wheel head, screwed both ends (ISI marked), complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 148.00 above but upto 40 mm bore, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 148.00 above but upto 25 mm bore, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 148.00 above but upto 20 mm bore, complete all as specified and directed by Engr-in-Charge.

All as per Ser item No 148.00 above but upto 15 mm bore, complete all as specified and directed by Engr-in-Charge.

Supply and fixing GI fittings medium grade ISI marked including complete all as required at site, complete all as specified and directed by Engr-in-Charge.

Elbow 15mm

Elbow 20mm

Elbow 25mm

Elbow 40mm

Elbow 50mm

Elbow 80mm

Socket 15mm

Socket 20mm

Socket 25mm

Socket 40mm

Socket 50mm

Socket 80mm

Union 15mm

Union 20mm

Union 25mm

Union 40mm

Union 50mm

Union 80mm

Elbow reducer 20 x 15mm

Elbow reducer 25 x 20mm

Elbow reducer 40 x 25mm

Socket reducer 25x20mm

Socket reducer 40x25mm

Socket reducer 40x20mm

Socket reducer 50x25mm

Nipple 15 x50mm

Nipple 15 x100mm

Nipple 20 x50mm

Nipple 20 x100mm

Nipple 25 x 50mm

Nipple 25 x 100mm

Nipple 40 x 50mm

Nipple 40 x 100mm

Nipple 50 x 50mm

Nipple 50 x 100mm

Tee 15mm

Tee 20mm

Tee 25mm

Tee 20x15mm

Tee 25x20mm

Tee 40x15mm

Tee 40x20mm

Tee 40x25mm

Tee 50x25mm

Dead plug 15mm

Dead plug 20mm

Dead plug 25mm

Dead plug 40mm

Dead plug 50mm

Lead wool

SHARMA SALES CORPORATION (BID ID -3310232)

PAUL TRADERS (BID ID -3316039)