Balance Work for 04-Storeyed Research Hostel at Zakura Campus.

Amount

Supplying, installing, testing & commissioning to the entire satisfaction of the owner , water closet squatting pan (Indian type W.C. pan ) of approved brand and quality with 100mm UPVC P or S trap , 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device(handle lever) conforming to IS : 7231, 40 mm pipe, flush bend, with all fittings and fixtures complete including cutting and refurbishing the walls, plate form and floors wherever required as per the directions of Engineer-in-charge. All should as per tender specifications . * White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Supplying, installing, testing & commissioning to the entire satisfaction of the owner, white vitreous china floor mounted water closet (European type W.C. pan) of approved brand and quality with seat and lid, 10 litre low level vitreous china flushing cistern with dual flush , conforming to IS:7213 with pvc flush bend with all fittings and fixtures such as brackets etc. complete including cutting and refurbishing the walls and floors wherever required as per the directions of Engineer-in-charge. All should as per tender specifications . * W.C. pan with ISI marked white solid plastic seat and lid .

Supplying, installing, testing & commissioning to the entire satisfaction of EIC white vitreous china wall mounted water closet (European type W.C. pan) of approved brand and quality with seat and lid, 10 litre flush cistern with all fittings and fixtures complete including cutting and making good the walls and floors wherever required as per the directions of Engineer-in-charge. All should as per tender specifications .

Wash Basin Supplying, installing, testing & commissioning of under counter White Vitreous China Wash basin of approved brand and quality size 560x450 mm with a 15 mm C.P. brass basin mixer and cp waste pipe 40mm, including painting of fittings and brackets, cutting and refurnishing the walls wherever required .

Supplying, installing, testing & commissioning of CP Brass bib cock of approved brand and quality complete as required, including necessary Accessories such as C.P Nipples C.P Cups etc as per the directions of EIC

P/f of pvc waste piipe of 40mm dia approved make and quality

Angle Valve Supplying, installing, testing & commissioning of C.P. brass angle valve of approved brand and quality

Supplying, installing, testing & commissioning of CP Brass two way bib cock of approved brand and quality with wall flange & Health Faucet / jet spray Chain type with C.P flexible pipe 1 m long, wall hooked complete as required, including necessary Accessories such as C.P Nipples and C.P Cups as per the directions of EIC

Urinal holder Supply & fixing in position wall mounted urinal holder of approved brand and quality complete in all respect including all fixing accessories as per requirement

Supply & fixing in position 20mm dia 600mm long CP Towel Rod of approved brand and quality with hooks s per the directions of Engineer-in-charge.

Soap Case Supply & fixing in position wall mounted Soap case of approved brand and quality complete in all respect including all fixing accessories as per requirement

Mirror Supply & fixing in position of 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing of 15mm size chromium plated cast brass wall mixer Non telephonic 3 in 1 with shower lead of of approved brand and quality

Urinal Supplying, installing, testing & commissioning to the entire satisfaction of the owner, white vitreous china flat back half stall urinal of approved brand and quality of size 580x380x350mm , with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, upvc trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and refurnishing the walls and floors wherever required as per direction of EIC.

Urinal Partition Supplying, installing, testing & commissioning to the entire satisfaction of the owner, urinalpartion of approved brand and quality of size 1200x450mm including painting of fittings and cutting and making good the walls wherever required as per direction of EIC.

Geyser Provind and fixing of electric water heater (Geyser) of approved brand and quality having copper storage tank 50 lt capacity. . with automatic thermostatic control electric element, 2000 watt pressure release valve, pvc connection, M.S. nuts and bolts etc.complete, conforming to IS: 2082. 50liters capacity.

Wash Basin Counter Construction of wash basin counters made up of 50mm thick RCC slab with 8mm dia reinforcement bars, centering, shuttering etc complete. the counter to be cladded with 19mm thick granite slab on top of the counter, 100mm granite facia , 150mm high back splash with moulding edge polishing etc. complete as per the directions of Engineer in Charge. The cost shall include all material, labour, lead and lifts etc.

Sink Providing and fixing stainless steel sink of approved brand and quality with drain board, C.I. brackets duly painted white, 40mm C.P. waste, 40mm pvc waste pipe with connection pipe to wall and C.P. wall flange, rubber adapter for waste connection complete including cutting and making good the walls wherever required. * Kitchen sink with drain board * 510x1040 mm bowl depth 250mm.

Sink MIXER Supplying, installing, testing & commissioning of 15mm CP brass sink MIXER of approved brand and quality with swivel casted spout of approved make.

Providing and fixing of 15mm size chromium plated cast brass wall mixer Non telephonic with lead of approved brand and quality

INTERNAL & EXTERNAL DRAINAGE WORKS uPVC Pipes (inside the Toilet in filling or chased in wall) Supply, installation,testing & commissioning of uPVC SWR PIPE of approved make confirming to IS:13592 - 1992, Class-B (for 75 mm to 110mm ND) , and IS 4985 - 2000, class-10 kg/sqcm (for 32 mm to 63mm) including fittingsall necessary fittings and specials such as bends , door bends , door tees , cowl piece, junctions offsets, access pieces, jointing with Tee shaped rubber seal ring confirming to IS : 5382-1985 and with PVC Adhesive Solvent, including Cutting, chases/holes in floors / walls / slab.The pipes shall be running over slab (in-filling) in areas such as toilets, Pantry etc. Cost shall be including jamming by pillers, supports of 1:2:4 concrete, as per required slope/Line & level complete as approved by Engineer-in-Charge. All should as per tender specifications .

uPVC Pipes (inside the shaft for soil , Waste & Vent) Supply, installation,testing & commissioning of uPVC SWR PIPE of approved make confirming to IS:13592 - 1992, Class-B , including all necessary fittings and specials such as bends , door bends , door tees , cowl piece , junctions offsets, access pieces, jointing with Tee shaped rubber seal ring confirming to IS : 5382-1985 and with PVC Adhesive Solvent.The pipes shall be running inside the shaft/ ceiling level , Fixed and supported by galvanized steel clamps & hangers/MS Brackets etc. duly epoxy coated and concrate 1;2;4;for fixing floor trap,pipes.. Making proper connection as approved by Engineer-in-Charge. All should as per tender specifications .

Floor Trap Supply, installation,testing & commissioning of PVC Floor Trap of size 110x75x50/40 inside the toilet/Pantry filling area of minimum 50 mm water seal , making necessary cutting in slab or floors and making good including supports with cement concrete 1:3:6 complete as approved by Engineer-in-Charge

CP Jali Supply, installing of approved make CP Jali with all fittings complete.

INTERNAL WATER SUPPLY PP-R PIPES . Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipesconforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including adopter ,onion, all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in-charge Water supply pipe

25 mm dia

32mm dia.

40mm dia

Hot water Supply

25 mm dia

32mm dia.

40mm dia

PP-R PIPES . FOREXPOSED PIPE I SHAFT/TERRACE Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipesconforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including adopter ,union, all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-in- charge Domestic water supply pipe

25mm dia.

32mm dia.

40mm dia

50mm dia

EXTERNAL WATER SUPPLY GI pipes for water supply pipe Supply, installation,testing & commissioning of GI -C heavy class pipeline of , including all fitting of IS 1239 of approved make with all -fittings like tees, bends, elbows, reducers, unions nipples etc. The item includes cutting of masonry, concrete as required,laying pipes at the required positions & levels including cutting & threding pipes, jointing with white zinc,Teflon tape etc providing clamps, hangers , etc testing & commissioning, making good, painting in required shade complete to colour coding. Underground

40mm dia

VALVE FOR INTERNAL AND EXTERNAL WATER SUPLY Ball Valve Providing and fixing PP-R Fittings of approved quality and make.

Tank nipple

25 mm dia

32 mm dia

40 mm dia

50 mm dia

External Sewerage Pipes ( From first manhole to final discharge location) Supply, installation,testing & commissioning of uPVC SWR PIPE of approved make confirming to IS:13592 - 1992, Class-B , including all necessary fittings and specials such as bends, junctions offsets, access pieces, jointing with Tee shaped rubber seal ring confirming to IS : 5382-1985 and with PVC Adhesive Solvent. Making proper connection as approved by Engineer-in-Charge. 160mm dia

Rectangular Manhole Construction of intercepting chambers of 230mm thick brick masonry in 1:3 cement mortar, 150mm thick foundation in 1:3:6 cement concrete, 20mm thick waterproof cement plastering in 1:3 to both internal and external surface finished with floating coat of neat cement, SFRC cover and frame (medium duty, MD-10 grade designation) 560 mm internal diameter conforming to IS:12592, total weight of cover and frame to be not less than 118 kg fixed over 100mm thick RCC coping in 1:2:4 cement concrete with 10mm dia. HYSD bars at 100mm center to center both ways, curing, complete including excavation, backfilling centering shuttering and disposal of surplus earth , as per specifications and directions of the Engineer-in-charge. All should as per tender specifications. 600 x 600 for depth upto 1.0m

Valve Chamber Constructing brick masonary chamber (for housing valves, Meters etc.) of brick work with bricks of class 75 with cement mortar 1:5 (1 cement:5 fine sand) plastering internal face with cement mortar 1:3 (1 cement: 3 fine sand and rough plaster on outer face with a floating coat of neat cement. R.C.C top slab with medium duty D.I. manhole cover and frame of 600 mm dia (weight : 60 KG). Including excavation, dewatering, refilling, watering, ramming and removing the surplus excavated material complete as required. (All sizes are clear internal sizes). Size 600 x 600 x 600 mm deep

POLYETHYLENE WATER STORAGE TANKS WITH INSULATION Supplying, installing, testing & commissioning of Polyethylene Water Storage Tank, including making holes for inlet, outlet, overflow, level indicator, drain & vent points and suitable cement concrete base including installation,testing & commissioning of thermal insulation over tank with EPS insulation having thermal resistance not less than 0.89 oK.m2/W at 25 deg F, density 40 kg/ cum as per ASTM C 578, covered with wire mesh and finally covered with 12mm thick cement plaster of 1:3 mix (1 cement:3 sand) including all accessories etc . For roof top mounting including CC base over existing slab and necessary tapecrete water proofing works , tank nipples , shutoff valves and float switch.

Construct brick masonry septic tank in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 Coarse sand : 4 graded stone aggregate 20mm nominal size) foundation concrete (1:4:8) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size finished with a floating coat of neat cement complete. Inside size 8 x 2.5 x 2.5 m deep including C.I. manhole cover medium duty with frame of size 60x60mm size. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects.

Suitable rating common electrical starter and control panel ( MCC panel) for above mentioned pumps along with necessary rating cabling , earthing ,control wiring etc. with proper dressing, necessary ancillaries such as cable tray ,cable tray stand etc. All should as per tender specifications

PUMPS with bore Supply, installation, testing and commissioning of water pump set 1.5 HP submirsible pump with 125mm dia bore 20 mtr depth including upvc pipe, G.I pipes, submirsible wire ,fittings complete all respects.

providing and fixing of 1. HP centrifugal water pump of approved quiality and make including all fittings etc complete in all respects.

Excavation Excavtion of trenches in all types of pipes of required width upto 2.5m depth for pipes including ramming of bottoms and get out the excavated soil and then back filling and sand bedding, dewatering of sub soil water /rain water etc. the same as required, in layers not exceeding 20cm depth including consolidatin each deposited layer by ramming, watering etc. and disposing the excess soil to the approved dumping ground as directed by the Engineer-in-Charge.

providing & laying hand packed stone soling compacted consolidated rammed filling voids all complete carriage upto site of work all heads complete job

Backfilling with available Earth Backfilling in plinth, in embankments , around footing, pits, trenches, foundations etc in layers not exceeding 200mm thickness , including watering ,compacting by ramming/rolling /hand ramming , levelling to specified slopes dressing and consolidation etc at optimum moisture content with mechanical rollers /rammers etc.(compacted to 90% modified proctor density )complete as per specification and as directed ( payment shall be based on certified excavation quantity less volume occupied by structures and therotical completed quantity.As measured from drawings,backfilling with available earth in and around excavated area.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to plinth level 1:4:8 (1Cement: 4 fine sand: 8 grade stone aggregate 40mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement all work up to all levels. 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20mm nominal size) Crushed

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to all levels. 1:3:6 (1Cement: 3 fine sand: 6 graded stone aggregate 20mm nominal Size) Crushed

Supplying, cutting, Bending to shape, fabricating, fixing and tying in postion TMT Reinforcement Steel of Fe 500D Grade at all levels and location as shown in the structural drawing. The reinforcement shall be of an approved brand and the rate shall include cost of supply & tying reinforcement with 18 guage GI building wire in the reinforcement rate. The unit rate shall also include cost of all related operations VIZ. inputs of labour, materials tools and tackle, equipment, machinery etc complete. for measuremnt purpose actual quantity for reinforcement bars provided and authentic laps or couplers provided shall be considered.

Brick work with FPS bricks of class designation 75 in super structure up to all floors. In cement mortar 1cement: 6 fine sand mortar.

Providing and fixing to correct level, line plum, vertical, ,circular formwork with contractors own material in all shapes made of MS sheets for RCC/PCC works including necessary strutting,scafffolding, bracing etc. leaving necessary recesses, opening chamfers etc. keeping the same in position during concreting and removing after the specified period all complete after as per specification and direction of EIC. For work Below 5.0 m and Above FGL

15 MM THICK PLASTER IN 1:4 CM Providing and applying average 15 mm thk cement plaster in single coat incement sand mortar 1:4 to all internal surfaces at all levels including surfacepreparation, staging, scaffolding and providing & fixing 20 Gauge 150mm widechicken wire mesh at all concrete & brickwork joints and roughening the surfaceas directed.

Providing and applying Acrylic based (Apex) paint of approved make and colour over the external surfaces at all levels inclusive of surface preparation by scrapping the surface .

SYNTHETIC ENAMEL PAINT Providing and applying three coats of Synthetic Enamel paint on all surfaces, in approved colourover a coat of primer including preparation of surface by thoroughcleaning, sand papering and as per manufacturer specification to give a smooth and even surface, necessary scaffolding etc., complete and asdirected by Engineer-in-charge.

Tile Dado. Providing and fixing Tiles in Cladding / Dado of approved shade,sizeand pattern on masonry walls including border fixed in pattern asapproved by EIC and fixed with rich cement slurry over abacking coatplaster of 12mm thk.Cement mortar 1:3 and grouted with app.shade grout (Bal Grout ) Rate to include, Tile cutting , cleaning ofjoints, finishingjunction of plaster ,curing etc. complete and asper drawing

SYNTHETIC ENAMEL PAINT Providing and applying three coats of Synthetic Enamel paint o all surfaces, in approved colourover a coat of primer including preparation of surface by thoroughcleaning, sand papering and as per manufacturer specification to give asmooth and even surface, necessary scaffolding etc., complete and asdirected by Engineer-in-charge.

Providing and fixing of M. S. Grill (ornamental) of angles / tees / flats / round and square bars/Hollow sections duly welded in frames of wall or with approved design, welded complete including ornamental tops including applying a priming coat of red oxide and two or more coats of synthetic enamel paint complete.

Manufacturing of wardrobes manifactured out of ISI marked 19mm ply in sides , shelves etc with ISI marked 6mm ply on back side and shutter manufactured out of 25mm ISI marked board. All internal surfaces to be finished with 0.8mm sunmica and all external surfaces to be finished with 1.0mm dulmica. The rate shall include cost of all hardware fittings such as S.S hanger rods and holders, tower bolts and ornamental handles, S.S hinges and long key lock and also the cost of 19mm wide matching PVC lipping fixed to all exposed edges both internally and externally. The wardrobe shall have to be fixed on 100mm high wooden frame also finished with the dulmica. 600mm deep

Manufacturing of single bed 6'-0"x3'-)" 1'-2" size box type manufactured out of 19mm ISI brand ply with base and top of box of ISI brand 12mm ply with requisite wooden supports as required. The head side shall be 2'-0" and foot side 0'-6" above the top surface of the box as per the design provided by the Engineer. the head side, foot side and two side to be fixed with 4 No. bed bolts. The rate shall include 75mm wide 12mm thick ply lipping on outer edges of all expoded sides and finished with 1mm thick dulmica and all required wooden beedings as per design and all hardware fittings.

Providing and fixing of stainless steel pipe curtain rods with stainless steel brackets. Knobs etc. ( 20mm dia .)

Providing and fixing of ready made curtains of approvid quality (Linen, Silk, Velvet) and colour to meet the requirement at all places. 1.5M wide

Stone work Sunk or moulded in cement mortor 1:4 (1 cement : 4 coarse sand) including pointing with white cement mortor 1:2 ( 1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade using fine chisel dressed Devri stone including all leads, lift complete job. Thickness not less than 230mm. Thickness ,shape & size as per the drawings & design approved and as per directions of EIC. Surface measurement to be measured for payment

Stone work moulding in cement mortor 1:4 (1 cement : 4 coarse sand) including pointing with white cement mortor 1:2 ( 1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade using fine chisel dressed Devri stone including all leads, lift complete job. Thickness not less than 25mm and width not less than 100mm Thickness ,shape & size as per the drawings & design approved and as per directions of EIC.

Providing & fixing of stainless steel (grade 304) gate made of hollow tubes,channels etc including welding grinding,buffing ,polishing & making curvatures & fitting the same with necessary stainless nuts & bolts complete i.e fixing the railing with necessary accessories & stainless steel dash fasteners,stainless steel bolts etc of required size on the top of the floor or the side of waist slab with suitable arrangements as per approval of engineer in-charge.

Providing & fixing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position including SS expansion fastners for brick/concrete work(including cost of all materials,leads, lifts & carriages etc upto site of work complete) 1st class imported wood

Providing and fixing 35 mm thick glazed shutters wire shuttersfor windows and clerestory windows using 10 kg/Sqm. (4mm thick) glass panes including black enameled ISI marked M.S. butt hinges with necessary screws.

SOLID LAMINATE FLUSH DOOR SINGLE LEAF Providing & fixing of 35mm thick (total built up 37mm) ISI marked Phenol Bonded single leaf flush door as per design of approved make. Job consists of covering flush door panel with 1.0 mm thick laminate of approved make and colour on both the sides of shutter as per design. Grooves in between laminate panels to be filled with epoxy based grout matching with the colour / contrast colour of laminate. The shutter shall be finished with 6 mm thick teak wood lipping Patti all around the shutter and finished with paint matching the lamination on the teak wood lipping Patti; Rates to include necessary hardware like, door lock , 150mm SS Tower bolt 2 No , door closer of 100 Kg capacity , SS Door door stopper , 4 No. of 100mm SS hinges etc. complete as per instructions of EIC

Providing hoisting and fixing trusses / purlins / rafters / posts, post plates, in planks and any sort of work or like components, including cost of screws nails etc. complete. First. Class Budloo wood.

Providing & Fixing Colored powder coated Galvalume high rib profile sheets roofing (thickness of sheet in mm: 0.50 TCT) curved as per sections /architectural drawings including Eave gutters, downspouts, Gable trims, corner flashing, drip trims, foam closures (inside and outside) and all necessary flashings 0.5mm prepainted (Color to be established during detail engineering stage).and fixing with polymer coated bolts, and nuts, GI plain and bitumen washers or with self drilling fastener and EPDM washers and necessary waterproofing sealants etc. complete as directed by Engineer in Charge. (Including Soffits, Eves boarding, Ridges Valleys etc)

Providing and applying plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Wash Basin Supplying, installing, testing & commissioning of Vitreous China Wash basin size 630x450 mm with a 15 mm C.P. brass basin mixer , pedestal of approved brand and quality including painting of fittings and brackets, cutting and refurbishing the walls wherever required .

Demolishing cement concrete work, including disposal of unserviceable material within 50 meters lead. 1:1.5:3 or richer mix.

Providing and fixing 1st quality ceramic glazed Digital tiles conforming to IS: 13753 of minimum thickness 5mm of approved make make in all colors, shades, except burgundy, bottle green, black of any size as approved by Engineer In Charge in skirting, riser of steps and dados over 12mm thick bed of cement mortar 1:3 (1 Cement: 3 coarse sand) and jointing with grey cement slurry @3.3 Kg per Sqm including pointing in white cement mixed with pigment of matching shade complete.

Chemical water proofing coatings by way of crystalline treatments and chemical grouts to prevent the passing of water through concrete surface by way of

Crystalline waterproofing caoting (Internal Coating )

Joint Repear (Repair of all cold &Construction joints )

Master Pel 777 (Std. packing 20 ltr Hydrophobic concrate Addiltive for making plaster waterproof)

Providing and fixig of MS manhole cover of size .600x600 including hings lock,painting etc complete job made out of 50x50x5mm angle and 6mm plates length frame and cover

1:2:4 (1Cement: 2 fine sand: 4 grade stone aggregate 20mm nominal size)

Supplying and filling of stone dust below Rcc pipes including waatering, ramming and dressing complate

Supplying and fixing of manhole steps made of 16mm dia mild steel square or round bars and encased/embeddded in protective plastic cover, complete in all respect.

Providing and laying non-pressure of specified class R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete. Non-pressure NP-3 class R.C.C. pipes

150mm dia

300mmdia

Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality circular shape 560mm internal dia

Providing and applying of Master top 33 curing aid, hardening, sealing and dust proofing compound for concrete. The liquid surface hardening compound shall be Mastertop 33, a clear non-organic, voc free, surface applied solution. The product shall improve the compressive strength of concrete by 15% pull off adhesion by 15% and abrasion resistance bt 40% complete as desired by EIC

Providing 150mm wide cemented moulding (thickness as per design) around window frames as per the architectural drawing and design in 1:2 mix. The rate shall include the cost of reinforcement in the form of nails as required including scaffolding ,upto 4 floor 4 level including priming coat and two coats of Apex paint

Cement Plaster in the form of panels as per architectural drawings and design in 1:2 mix with the thickness varying from 20 to 30 mm in the form of tappered surfaces. The rate shall include the cost of reinforcement in the form of nails as required including scaffolding ,upto 4 floor 4 level including priming coat and two coats of Apex paint

M/S FALCON CONSTRUCTION COMPANY

M/S NASEER AHMAD BHAT

M/S ALLIANCE CONSTRUCTIONS