REPAIR TO SANITARY FITTING, PLASTERING, SUNKEN FLOOR, INTERNAL WATER SUPPLY FOR OTM MD ACCN UNDER AGE B/R - I AT ITARANA ALWAR

Amount

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc 15 cm thickness (below or above ground level.) & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

Demolition of brick/stone masonry built in cement/lime mortar of any mix and stacking serviceable stones aside for reuse & removing unserviceable materials in low laying area, complete, all as directed by Engr-in-Charge.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

Material and labour brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L for rendering 15mm thick in cement plaster 1:6 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair face of brick work of walls, mixed with water proofing compound (ISI marked), finished even & smooth without using extra cement complete all as specified. Note : - Supply only water proofing compound shall be measured and paid for separately.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

Supply only integral water proofing compound (ISI marked).

Material and labour preparation of newly plastered surface of walls & applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered surface of walls & applying two coats of cement base paint over a coat of primer complete all as specified.

M&L for preparation of new plastered surfaces and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of chalk whitening on walls all as specified & as directed.

M&L brooming down old decorated surfaces of walls, plastered including cornices, pilasters etc and applying one coat of white wash complete all as specified.

M&L brooming down old decorated plastered/asbestos cement surfaces of ceilings & applying one coat of white wash complete all as specified.

M&L for brooming down old decorated surfaces of wall, plastered or unplastered including cornices, pilasters etc and applying one coat of oil bound distemper of approved shade, complete, all as specified and directed.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified & as directed.

Material and labour glazed ceramic tiles (coloured) Ist quality 350mm x 250mm x 7mm / 450mm x 350mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in base course or levelling course and including Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified & as directed.

BLANK

Material and labour coloured non skid ceramic tiles 7 to 8mm thick Ist quality (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

Material and labour for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick Ist quality (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering (as screed bed) in cement & sand mortar 1:4 complete all as specified and as directed.

M&L machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L machine cut Kota stone slab 10 to 15mm thick , as in riser of step, skirting, dado etc. laid over & including screed bed or bedding layer of 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

S&F in repairs PVC connection 600 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides, complete all as specified.

S&F in repairs PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I. Note:- Unit Rate deemed to include taking down old one.

Fixing only in repairs 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I. Note:- . (i) Water tank shall be issued under Sch 'B' free for fixing only

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I. Note:- Unit Rate deemed to include taking down old one.

Fixing only in repairs 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I. Note:- (i) Water tank shall be issued under Sch 'B' free for fixing only

S&F in repairs pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot or cold' long screwed shanks and fly nuts, screwed for iron pipe and fixed bore of pipe in 15mm dia.

Fixing only in repairs pillar taps, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot or cold' long screwed shanks and fly nuts, screwed for iron pipe and fixed bore of pipe in 15mm dia. Note:- (i) Pillar tap shall be issued under Sch 'B' free for fixing only

Supply and fixing as in repairs Ball valves, high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball, screwed for iron pipe 20mm dia (minimum weight 210 gms) complete all as specified and as directed.

Fixing only in repairs Ball valves, high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball, screwed for iron pipe 20mm dia (minimum weight 210 gms) complete all as specified and as directed. Note:- (i) Ball valves shall be issued under Sch 'B' free for fixing only

S&F in repairs 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

Fixing only in repairs 15 mm bore bib tap, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule. Note:- (i) Bib tap shall be issued under Sch 'B' free for fixing only

S&F 15 mm bore bib tap, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed as in repairs.

S&F as in repairs 15mm bore bib tap standard of PTMT any colour, high pressure, screwed for iron pipe and fixed (minimum weight 90 gms) complete all as specified and as directed.

Fixing only as in repairs 15mm bore bib tap standard of PTMT any colour, high pressure, screwed for iron pipe and fixed (minimum weight 90 gms) complete all as specified and as directed. Note:- (i) Bib tap shall be issued under Sch 'B' free for fixing only

M&L for repair to exising 15mm bore bib tap/stop cock/Angle valve etccast copper alloy chromium plate by replacing brass jumper assembly with spindle, (brass Tee/elbow for MAP Qtr) PVC washer etc complete all as directed. Note : (i) Contractor or his authorised representative collect such type of complaints from B/R - I complaint cell at 9.00 AM on daily basis except sunday /Holiday. No extra payment shall be made on account of collection of complaint.

M&L for repair to existing 15mm bore bib tap/stop cock etc cast copper alloy by replacing brass jumper assembly PVC washer etc matching with existing complete all as directed. Note : (i) Contractor or his authorised representative collect such type of complaints from B/R - I complaint cell at 9.00 AM on daily basis except sunday /Holiday. No extra payment shall be made on account of collection of complaint.

S&F in repairs 15mm bore Stop valve, cast copper alloy, fancy type chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union.

Fixing only in repairs 15mm bore Stop valve, cast copper alloy, fancy type chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union. Note:- (i) Stop valve shall be issued under Sch 'B' free for fixing only

S&F in repairs 15 mm bore stop cock, CP, brass with crutch or butterfly handle, screwed down for iron pipe complete all as specified and directed.

Fixing only in repairs 15 mm bore stop cock, CP, brass with crutch or butterfly handle, screwed down for iron pipe complete all as specified and directed. Note:- (i) Stop cock shall be issued under Sch 'B' free for fixing only

S&F in repairs brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore all as specified and as directed.

Fixing only in repairs brass chromium plated wall mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore all as specified and as directed. Note:- (i) Wall mixer shall be issued under Sch 'B' free for fixing only

S&F in repairs screwable plastic lid cover including frame fixed with screw for existing 500 ltr capacity rotational moulded polythylene water tanks complete all as specified and directed. Note :- Cover shall be provided of make as per existing water tank.

S&F in repairs screwable plastic lid cover including frame fixed with screw for existing 1000 ltr capacity rotational moulded polythylene water tanks complete all as specified and directed. Note :- Cover shall be provided of make as per existing water tank.

S&F in repairs waste fitting 32mm bore, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including 32 mm dia PVC waste pipe, complete all as specified.

S&F in repairs waste fitting 38/40mm bore, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including 38 mm dia PVC waste pipe, complete all as specified.

S&F in repairs Jet spray chromium plated brass for EWC with & including PVC connection 900 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete.

S&F in repairs Jet spray PTMT for EWC with & including PVC connection 900 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete.

S&F in repairs health faucet, brass chromium plated for EWC with & including PVC connection 600 mm long suitable for 15 bore GI pipe with PTMT nut & nipple complete all as specified and directed.

S&F in repairs Plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repairs waste coupling of PTMT (half or full threaded) suitable for WHB/Sink, bore dia of discharge pipe 32mm (Minimum weight 45gms).

S&F in repairs waste coupling of PTMT (half or full threaded) suitable for WHB/Sink, bore dia of discharge pipe 40mm (Minimum weight 60gms).

S&F in repairs 32 mm dia PVC flexible waste pipe 80 cm long with socket for union, for WHB/urinal/sink complete all as specified and directed.

S&F in repairs 40 mm dia PVC flexible waste pipe 80 cm long with socket for union, for WHB/urinal/sink complete all as specified and directed.

S&F in repairs 15mm bore Angle valve chromium plated screwed down, high presuure with capstan heads screwed both ends for iron pipe or for union complete all as specified.

S&F in repairs 15mm bore two way Angle valve chromium plated screwed down, high presuure with capstan heads screwed both ends for iron pipe or for union complete all as specified.

Supply and fixing as in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

Supply & fixing in repairs vitreous china squatting pan (Orissa pattern) water closet (white) size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) complete including connection to trap and flushing pipe antisyphonage pipe etc including provision of PCC (1:7:12) type F2 in filling complete all as specified.

Dismantling & taking down 15mm bore PVC pipes & connections from wall, ceiling, floor, trenches complete all as specified and directed.

Dismantling & taking down 20mm bore PVC pipes & connections from wall, ceiling, floor, trenches complete all as specified and directed.

Cleaning & refixing old PVC pipe of 15 mm bore and connections in new or old position on wall, ceiling, floors etc & extra union near stop, tank nipple and saddle piece complete all as specified and directed.

Cleaning & refixing old PVC pipe of 20 mm bore and connections in new or old position on wall, ceiling, floors etc & extra union near stop, tank nipple and saddle piece complete all as specified and directed.

S&F to walls/chases/ceilings or laying in floors 1216 (outside dia - 16mm) polyethylene-Aluminium-Polyethylene (PE-AL-PE) composite pressure pipes including all Crimp type internal sealing Plansticmetal Composite fittings (such as elbows, tees, reducers, couplers, short pieces, connectors, etc) and hooks (in case of concealed pipe work)/ clamps (in case of exposed pipe work) complete all as specified & as directed.

S&F to walls/chases/ceilings or laying in floors 1620 (outside dia - 20mm) polyethylene-Aluminium-Polyethylene (PE-AL-PE) composite pressure pipes including all Crimp type internal sealing Plastic metal Composite fittings (such as elbows, tees, reducers, couplers, short pieces, connectors, etc) and hooks (in case of concealed pipe work)/ clamps (in case of exposed pipe work) complete all as specified & as directed.

S&F in repairs vitreous china wash hand basin, white, flat back of size 580mm x 450mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F repairs sink made of stainless steel 1mm thick for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to dwarf wall, connecting union to pipe, overall minimum size 495mm x 420mm bowl size 410mm x 330mm x 160mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete, all as specified and directed.

S&F fixed in repair vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and jet spray PTMT including 600 mm long PVC connection suitable for 15mm bore GI pipe/Stop Valve complete all as specified & as directed.

Taking up or down 15mm bore steel tubing and connection incl cleaning for refixing or removal to store

M&L galvanised steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Refixing old steel tubing and connection in new or old position (wall, ceiling, floor etc) of 15mm bore of pipe.

Taking up or down 20mm bore steel tubing and connection incl cleaning for refixing or removal to store

M&L galvanised steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

Refixing old steel tubing and connection in new or old position (wall, ceiling, floor etc) of 20mm bore of pipe.

Taking up or down 25mm bore steel tubing and connection incl cleaning for refixing or removal to store

M&L galvanised steel water tubing medium grade of 25mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

S&F chromium plated brass shower rose screwed for 15 mm bore GI pipe, 125 mm bore fixed in repairs.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed on wall with PVC rawl plug & cadmium plated brass screws, complete all as directed.

S&F in repairs corner shelf 300m long made of toughned glass minimum thickness of glass 5.5 mm thick with stainless steel railing fixed to wall by means of brass screws and rawl plugs complete all as specified and directed.

S&F as in repairs mild steel stove enameled black casement stay 300mm long for steel windows, with hinged joint & two plates, with studs complete all as specified.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting exc 10 cm but not exc 20 cm girth in brick walls.

S&F in repairs bottle trap of PTMT for wash hand basin having minimum water seal of 25mm (minimum weight 260 Gms) and bore of discharge pipe of 32mm complete all as specified and directed.

S&F in repairs 32mm bore Brass chromium plated bottle trap for wash basin with inlet and outlet screwed for pipe or connections including necessary packing, union and cap complete all as specified.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each.

Taking down chowkat or frame with shutters area not exc. 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts complete all as specified.

Supply and fixing factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

Taking down frame with shutters for window / ventilator area not exc. 1.5 Sqm each (without taking off the shutters from the frame) including guard bars of any description complete all as specified

Taking down frame with shutters for window / ventilator area exc. 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) including guard bars of any description complete all as specified

Supply & fixing butt hinges of size 100mm extruded aluminium alloy with galvanised mild steel hinge pin type B-21 anodised complete all as specified.

Supply & fixing factory made ‘Z’ type section steel windows with side hung shutters including projecting type hinges with steel handles and peg stay with glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

Supply & fixing factory made ‘Z’ type section steel windows with side hung shutters including projecting type hinges with steel handles and peg stay without glazing bars dovetailed or welded including one shop coat of Zinc Chromate primer complete all as specified.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, handle including one shop coat of Zinc Chromate primer complete all as specified.

Supply and fixing 200 mm long mild steel barrel tower bolts, stove enameled black with bright bolts and fixed complete all as specified

Supply and fixing 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

Supply and fixing 300 mm long mild steel sliding door bolts clip type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, ISI marked complete all as specified.

Supply and fixing 150 mm long mild steel pressed handle, oval type, stove enameled black complete all as specified

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

Supply & fixing aluminium handle 125mm size cast type, anodized complete all as specified.

S&F in repairs powder coated mild steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with & including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for in this Schedule all as specified & directed.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors and similar works of Gde E-165(Fe 290) including welding etc. complete all as specified & as directed.

S&F Bands, straps, supports or stays for rainwater, ventilating, pipes, including bolts, if required: hooks (stays), heavy, for large gates, hooks and pintal hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle, cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way strapes, plate washers and similar small articles confirming to Fe 410 or Fe 310.

Supply and fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

Supply and fixing in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

Material and labour preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

BLANK

Supply and fixing 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, glazing in repairs, complete all as specified.

S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, glazing in repairs, complete all as specified.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 metre in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for 40mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in flooring, finished even and smooth with using extra cement complete all as specified & as directed. Note : - Glass dividing strips shall be measured and paid for separately as “Supply only” under relevant item of this Schedule.

Supply only glass dividing strips 3mm thick and 38mm wide.

M&L for 20mm thick Granite slab of approved shade, as in platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) including required cutting to suit the size of oval type wash hand basin over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for 20mm thick Granite (of any type) work as in as in skirting/dado over & including 10mm thick screed bed (bedding layer) in CM 1:4, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting and polishing (mirror polish i.e. full granite polish as per local trade practice) all as specified & directed.

Taking down bib taps, stop cock, shower rose etc and removing blockages or air lock from GI/PVC tubing 15/20/25 mm dia by applying pressure through suitable pressure pumps/using acid/chemical to clear any blockage and refixing bib taps, stop cocks, shower rose etc. Note : (i) Contractor or his authorised representative collect such type of complaints from B/R-I complaint cell at 9.00 AM on daily basis except sunday / Holiday. No extra payment shall be made on account of collection of complaint.

M&L running welding in repairs, thickness of metal to be welded not exc 6mm all as specified & as directed.

M&L for running welding in repairs, thickness of metal to be welded exc 6 mm but not exc 9mm, all as specified & directed.

S&F 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified.

S&F 75 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified.

S&F in repairs 100mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door.

S&F in repairs 75mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door.

S&F as in repairs 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

S&F as in repairs 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified & as directed.

Supply and fixing in repairs CI Nahani trap with 75 mm bore outlet with CP grating including jointing to waste pipes with lead joint fixed in PCC 1:2:4 type B-1 using 20mm graded stone aggregate complete all as specified.

S&F in repairs cast iron trap ‘P’ or ‘S’ for 100 mm bore pipe complete all as specified & as directed.

S&F in repairs PVC trap ‘P’ or ‘S’ for 110 mm bore pipe complete all as specified & as directed.

Supply and fixing 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified including taking out old unserviceable PVC pipe with fittings.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including taking out old unserviceable PVC pipe with fittings.

Supply and fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified including taking out old unserviceable PVC pipe with fittings.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified including taking out old unserviceable PVC pipe with fittings.

S&F 75 mm bore PVC (SWR) bends any radius provided with access door complete all as specified.

S&F 110 mm bore PVC (SWR) single junction (single 'T' ) equal or unequal provided with access door complete all as specified.

S&F 75mm bore PVC (SWR) branch piece, single (single ‘Y’) equal or unequal.

Supply and fixing 110 mm bore PVC (SWR) bends any radius complete all as specified.

Supply and fixing 75 mm bore PVC (SWR) bends any radius complete all as specified.

Supply and fixing 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F PVC (SWR) floor trap dia of outlet 75mm, with PTMT grating including jointing with solvent cement including taking out old unserviceable trap.

S&F in repairs PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement complete all as specified.

S&F MS holdfast, hook and pintle hinges, large hasp and staples, clamps, hooks for hanging fans and similar small articles conforming to Grade E-165 (Fe 290) including necessary welding etc. and fixed in position.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) all as specified & as directed.

M&L reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete.

M&L formwork to edges of concrete flats, roofs, floors etc not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for rough finished surfaces.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia, complete, all as specified and directed.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates and the like including weathering, slightly rounded, chamfered angle and throating as directed including use and waste of form work (straight or curved) all exposed surface of concrete finished fair complete all as specified & as directed.

Material and labour 75 mm thick PCC (1:4:8) type D2 using 40 mm graded stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L factory made 60mm thick machine pressed precast cement concrete interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and no pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as Specified & directed.

M&L precast cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in kerb block with plain fair faces, kneelers, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angle throating, with plain or interlocking joints and setting in cement mortar 1:4, complete, all as directed.

M&L for 25 to 30mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, not exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4, complete.

Cleaning & removing all scale & dirt etc from tanks & from mouths of circulating pipes etc of capacity exc 250 litres & not exc 500 litres with gunny bags, cleaning with fresh water and bleaching powder including writing letter height not less than 15cm with synthetic enamel paint using stencil as (Tank Cleaned on -Dated-) all as specified and directed.

Cleaning & removing all scale & dirt etc from tanks & from mouths of circulating pipes etc of capacity exc 500 litres & not exc 1000 litres with gunny bags, cleaning with fresh water and bleaching powder including writing letter height not less than 15cm with synthetic enamel paint using stencil as (Tank Cleaned on -Dated-) all as specified and directed.

M & L for water proofing treatment in sunken floors as described hereunder:- (i) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick cement plaster in mortar 1:4 mixed with water proofing compound @ 3% by weight of cement. (ii) Preaparing plastered surfaces and providing APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm of make super thermolay manufactured by STP Ltd or ‘Hyper Plas’ (Polyster) manufactured by M/S IWL Ltd or ‘Shaliplas’ (polyester) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or ‘EMW FLATE’ of M/S Texas India Ltd} at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions, complete all as specified and as directed. Note: (i) Polymeric membrane shall be laid in sunken floor and on sides upto finished floor level (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iii) Above aspects are deemed to be included in quoted rate. (iv) Supply only water proofifng compound shall be measured and paid separatgely).