EQUIPMENTS

List of Equipment Items

LVDT Trainer Kit SPECIFICATION (with Suitable number of patch cards ) 1. DISPLAY : Seven segment LED to display output Voltage values ( with polarity indicator ) ( DPM Circuitry ) 2. Single turn Potentiometer to calibrate the instrument. 3. To study characteristics behaviour of LVDT in positive and negative region with respect to voltage . 4. SENSITIVITY: 10 mV/mm 5. MICROMETER Measurement system. 6. LVDT ( i. TYPE: Linear displacement ii.CONFIGURATION : Axial type iii. LVDT Fullstroke : +10mm range iv. ACTUAL Displacement --> Micrometer type v. Pitch 1mm. )

Arduino UNO board with IC L293D with DC motor interfacing withoptical sensor setup to measure the speed of the DC motor kit SPECIFICATION 1) Arduino UNO board ATmega328 microcontroller, Input voltage - 7-12V, 14 Digital I/O Pins (6 PWM outputs), 6 Analog Inputs, 32k Flash Memory, 16MHz Clock Speed , 2) DC motor DC motor interface with Arduino with L293D motor driver. Voltage : <100 V, Power : <50 W, Power Source : DC, Speed : 10001-14000 RPM, Motor Type : 775 Motor, 3)L293D Motor driver Wide Supply-Voltage Range: 4.5 V to 36 V Output Current 0.6 A Per Channel. Pin compatible with L293D. 4)Optical sensor Using imported groove optical coupling sensor, width 5mm. If it covered, it will output high level; otherwise it output low level. The working voltage of 3.3V to 5 V. Output: digital switch output(0 and 1)

DC Dual Variable Power Supply Unit SPECIFICATION Range 0-30v Variation: both fine and coarse with current and voltage variation through potentiometer Display: Seven segment LED display to display voltage

Arduino sheild Board kit Ultrasonic sensor, Inductive soil Moisture sensor, Servo motor,Potentiometer, ( with Suitable number of patch cards ) SPECIFICATION 1. ARDUINO SHIELD BOARD: Power supply : 5-12 V, Motor controller : L 298P, Drives 2DC motor or 1 stepper motor, Max current : 2A per channel or 4A max ( with external power supply ) , Current sensing : 1.65 V/A. 2. ULTRASONIC SENSOR: Power supply : 3.3-5V, Operating current : 8mA, Working frequency : 50 Hz, Ranging distance : 1cm-350cm, Resolution : 1cm, Measuring angle : 15degrees, Trigger Input Pulse width: 10uS. 3. MOISTURE SENSOR: Voltage rating : 3.3-5V,Output Voltage - 3V, Opearing current - 5 mA, Temperature : 0 degree C to 40 degree C, Accuracy : ± ( 0.5 % n+1 ) 4.SERVO MOTOR: Operating Voltage : 5V, Torque : 2.5 Kg/cm, Operating speed : 0.1s / 60 degree C 5.POTENTIOMETER: Resistance : 0-2 KΩ

Interfacing push button , SPST, SPDT, Limit switch with 12 V DC motor kit SPECIFICATION ( with Suitable number of patch cards ) 1. Push button type ( to drive 12 V DC motor . i. Normally open- each one ii . Normally closed - each one ) 2. SPST - On -Off toggle switch ( to drive 12 V DC motor ) 3. SPDT - On -Off toggle switch to drive Load 1 - 12 V DC motor1 to drive Load 2 - 12 V DC motor2 4. LIMIT SWITCH - to drive 12 V DC motor 5. 12 V DC Motor - 2 Power supply.- 12 V DC , 500 mA to drive DC motors

Interfacing Transistor and relay with 12 V DC motor kit ( with Suitable number of patch cards ) SPECIFICATION 1. Transistor - BJT (BC 107 ) 2. Relay : i. NO (Normally Open ) ii. NC (Normally Closed ) Coil Voltage rating - 12 V DC Swiching circuit Voltage & Current rating - 12V DC , 500 mA 3. 12 V DC motor - 2 Power supply 12V DC , 500 mA to drive DC motors

3 Phase Induction Motor, Forward Reverse Control switch and Clamp Meter (with suitable no of patch cards) SPECIFICATION One HP- 3 Phase Squirrel cage Induction motor

440V , 10 A 3 Phase DOL STARTER KIT with Forward / Reverse control switch 1. 3⌀ DOL Starter (To drive 3⌀ Squirrel cage Induction motor) 2. I/P 3 phase connectivity pins 3. O/P 3 phase connectivity pins 4. Forward / Reverse control switch 3 Phase AC DOL Starter kit with Forward / Reverse Control switch test kit ( with Suitable number of patch cards ) -

Clampmeter - (TONGUE TESTER )

TECHLAB ELECTRONICS (BID ID -1271428)

Vi Microsystems Pvt Ltd (BID ID -1271421)