Renovation of type IV-C, D-Type and C-Type Houses (05 Nos. Each Type Houses) in IIT Delhi Campus.

Amount

1) Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

1.1) All kinds of soil.

2) Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

3) Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

3.1) 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

3.2) 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

4) Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

5) Centering and shuttering including strutting, propping etc. and removal of form for :

5.1) Shelves (Cast in situ)

6) Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

6.1) Thermo-Mechanically Treated bars

7) Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

7.1) Cement mortar 1:4 (1 cement : 4 coarse sand)

8) Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

8.1) Cement mortar 1:3 (1 cement :3 coarse sand)

9) Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

10) Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

10.1) Granite of any colour and shade

10.1.1) Area of slab upto 0.50 sqm

10.1.2) Area of slab over 0.50 sqm

11) Providing edge moulding to 18 mm thick marble stone counters, vanitiesetc, including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.

11.1) Granite work

12) Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

13) Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

13.1) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

14) Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

14.1) Fixed to openings /wooden frames with rawl plugs screws etc.

17) Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.

18) Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

18.1) Twin rubber stopper

19) Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

19.1) Double strip (horizontal type)

20) Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer- in-charge.

21) Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

22) Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

22.1) Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

23) Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

24) Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

24.1) Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

25) Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles.

26) Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness.

27) 15 mm cement plaster:

27.1) 1:4 (1 cement : 4 fine sand)

28) 12 mm cement plaster finished with a floating coat of neat cement of mix :

28.1) 1:3 (1 cement: 3 fine sand)

29) 6 mm cement plaster of mix :

29.1) 1:3 (1 cement : 3 fine sand)

30) Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

30.1) Water thinnable cement primer

31) Applying priming coat :

31.1) With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

32) Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :

32.1) Two or more coats on new work

33) Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

33.1) Two or more coats on new work

34) Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

35) Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead :

35.1) With cement mortar 1:4 (1 cement : 4 fine sand)

36) Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

37) Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

37.1) Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

38) Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

39) Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

39.1) In cement mortar

40) Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

40.1) Of area 3 sq. metres and below

40.2) Of area beyond 3 Sq. meters

41) Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

41.1) For thickness of tiles 10 mm to 25 mm

41.2) For thickness of tiles above 25 mm and up to 40 mm

42) Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :

42.1)75 to 80 mm dia pipe

42.2) 100 mm dia pipe

43) Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-charge :

43.1) 15 mm to 40 mm nominal bore

44) Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

45) Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

46) Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

47) Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

47.1) White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

48) Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

48.1) W.C. pan with ISI marked white solid plastic seat and lid

49) Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

49.1) White Vitreous China Angle back wash basin size 600 x 480 mm with single 15mm C.P. brass pillar tap

49.2) White Vitreous China Angle back wash basin size 400 x 400 mm with single 15 mm C.P. brass pillar tap

50) Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and aking good the walls wherever required :

50.1) Kitchen sink without drain board

50.1.1) 610x460 mm bowl depth 200 mm

51) Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

51.1) Flexible pipe

51.1.1) 32 mm dia

52) Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

53) Providing and fixing soil, waste and vent pipes :

53.1) 100 mm dia

53.1.1) Sand cast iron S&S pipe as per IS: 1729

53.2) 75mm diameter :

53.2.1) Sand cast iron S&S pipe as per IS: 1729

54) Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. :

54.1) For 100 mm dia pipe

54.2) For 75 mm dia pipe

55) Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

55.1) 100 mm dia

55.1.1) Sand cast iron S & S as per IS-1729

55.2) 75 mm dia

55.2.1) Sand cast iron S & S as per IS-1729

56) Providing and fixing plain bend of required degree.

56.1) 100 mm dia

56.1.1) Sand cast iron S&S as per IS - 1729

56.2) 75 mm dia

56.2.1) Sand cast iron S&S as per IS -1729

57) Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

57.1.1) Sand cast iron S&S as per IS - 1729

57.2.1) Sand cast iron S&S as per IS-1729

58) Providing and fixing single equal plain junction of required degree :

58.1.1) Sand cast iron S&S as per IS-1729

58.2.1) Sand cast iron S&S as per IS-1729

59) Providing and fixing collor:

59.1.1) Sand cast iron S&S as per IS-1729

59.2) 75 mm dia

59.2.1) Sand cast iron S&S as per IS-1729

60) Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :

61) Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors

61.1) 100 mm inlet and 75 mm outlet

61.1.1) Sand Cast Iron S&S as per IS- 1729

62) Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall

62.1) 15 mm dia nominal bore

62.2) 20 mm dia nominal bore

62.3) 32 mm dia nominal bore

63) Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

63.1) 15 mm dia nominal bore

63.2) 20 mm dia nominal bore

64) Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work

64.1) 20 mm dia nominal bore

65) Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :

65.1) 25 to 40 mm nominal bore

66) Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

66.1) 20 mm nominal bore

67) Providing and fixing unplasticised PVC connection pipe with brass unions.

67.1) 45 cm length

67.1.1) 15 mm nominal bore

68) Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :

68.1) 15 mm diameter pipe

68.2) 20 mm diameter pipe

69) Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

69.1) 15 mm diameter pipe

69.2) 20 mm diameter pipe

69.3) 32 mm diameter pipe

70) Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

70.1) 15 mm nominal bore

70.2) 20 mm nominal bore

71) Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

72) Cutting holes up to 30x30 cm in walls including making good the same:

72.1) With common burnt clay F.P.S. (non modular) bricks

73) Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :

73.1) 100 mm diameter

74) Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

74.1) 100 mm diameter S.W. pipe

75) Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

75.1) 100x100 mm size P type

75.1.1) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

76) Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :

76.1) For pipes 100 to 250 mm diameter

77) Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

77.1) With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm)

78) Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

79) Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

79.1) 20 mm nominal bore

80) Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

80.1) For fixed portion

80.1.1) Powder coated aluminium (minimum thickness of powder coating 50 micron)

81) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

81.1) Powder coated aluminium (minimum thickness of powder coating 50 micron)

82) Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineerin-charge complete.

83) Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately)

84) Providing and Fixing of CP Brass bib cock (Short body) of approval quality complete as per the direction of Engineer in-charge. (Make - Jaquar/Marc/Kohler)

84.1) 15mm nominal bore

85) Providing and Fixing of C.P. brass bib cock (long body) of approved quality complete as per the direction of Engineer in-charge. (Make - Jaquar/Marc/Kohler)

85.1) 15mm nominal bore

86) Providing and Fixing of C.P. brass angle valve/angular stop cock for wash basin and geyser and WC points of approved quality complete as per the direction of Engineer in-charge.(Make - Jaquar/Marc/Kohler)

87) Providing and Fixing of C.P. brass stop cock (concealed) of standard design as per directions of Engineer-In-Charge conforming to IS:8931. (Make: Jaquar/Marc/Kohler)

87.1) 15mm nominal bore

88) Providing and Fixing hand health faucet of standard size and design with one metre long flexible tube and wall hook complete in all respect.- (Make: Jaquar/Marc/Kohler)

89) Providing and Fixing of C.P. brass shower head with arm complete as per the direction of Engineer in-charge. (Make: Jaquar/Marc/Kohler) 15mm nominal bore

90) Providing and Fixing of C.P. brass wall mixture tap of approved quality complete as per the direction of Engineer in-charge. (Make:Jaquar/Marc/Kohler).

90.1) 15mm nominal bore

91) Providing and Fixing of C.P. brass Bottle Trap for Wash basin of approved quality complete as per the direction of Engineer in-charge. (Make:Jaquar/Marc/Kohler).

92) Providing and Fixing of C.P. Central Hole Basin Mixer of approved quality complete as per the direction of Engineer in-charge. (Make - Jaquar/Marc/Kohler) - 15mm nominal bore

93) Removing of old iron door shutters and refixing the same after alternation in size, grill, sheet and wiremesh repair, godown lock replacing/repairing all complete as per the direction of Engineer in-charge.

94) Providing and fixing cup board shutters with 18-19mm thick BWR Plywood as per IS : 303 of approved make with necessary SS piano hinges of appropiate size etc. complete as per direction of Engineer In Charge.

95) Providing and fixing 6mm thick BWR ply wood sheet (ISI marked) in cup board including necessary glue and nails etc. complete as per direction of Engineer In Charge.

96) Providing and fixing cup board inside shelves, sides, back portion, drawers etc. with 18-19 mm thick BWR Plywood as per IS : 303 of approved make with necessary fixing arrangement and as per requirement complete as per direction of Engineer In Charge.

97) Providing and Fixing stainless steel jali (Grating) with or without hole for waste pipe for floar / Nahni trap. (Make - Chili / Hefle)

98) Providing and fixing Curtain/Drapery Rod with finials and rings (28mm diameter Electric Resistance Welded MS pipe having a corrugated virgin PVC extrusion on it. The finials and rings are made of ABS plastic in matching colours with an option of golden finish) in required position including Curtain Brackets/ End Knobs/ Pipe Holders etc. and including necessary cutting, tightening/fixing as required complete as per the instructions of Engineer-in-charge. (Make: Vista-Soffio-II or equivalent of MAC). Note:- For payment purpose total end to end length of rod including End Globe will be measured and no extra payment will be made for Curtain Bracket, End Knob, Pipe Holder, Finials and rings.

99) Providing and Fixing of glass corners of any size with necessary cleats and screws etc. complete as per the direction of Engineer in-charge. (Make: Jaquar/Marc/Kohler)

100) Providing and Fixing of glass shelf 600 mm long of any size with necessary cleats and screws etc. complete as per the direction of Engineer in-charge. (Make: Jaquar/Marc/Kohler)

101) Providing and fixing G.I. Tank Nipple in PVC Tanks.

101.1) 15 mm nominal bore

102) Providing and fixing fly proof wire gauge to windows, clerestory windows and doors with screws/ washer etc. or by approved means as per manufacture's specifications. (a) Stainless steel (grade 304) wire gauge of 0.38 mm dia wire and 1.4 mm aperute on both sides. (complete area of shutter will be measured for payment and no extra payment for folding the wire gauge at edges will be made for material and labour etc.)

103) Providing and fixing s.s. 304 Grade sliding door bolts with nuts and screws etc. complete :

104) Providing and fixing S.S 304 tower bolt (Barrel type) with necessary screws etc. complete :

105) Providing and fixing concealed handle for Aluminium window shutter of 128 mm conforming to IS: 733 and IS: 1285, fixingwith necessary screw, beading etc as per direction of Engineer in charge.

106) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A

107) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B

108) Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

109) Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

110) Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required

110.1) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

110.2) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

110.3) 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire

111) Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required

112) Suplying and fixing brass batten/ angel holder i/c connntion etc as required.

113) Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required

114) Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

115) Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

116) Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

116.1) 1 or 2 Module (75 mm x 75 mm)

116.2) 12 Module (200 mm x 150 mm)

117) Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

117.1) 5/6 A switch

117.2) b. 3- pin 5/6 amps socket outlet.

118) Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

119) Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

120) S/I/T/C of decorative wall light fixture suitable for upto 1X 9 watt. LED lamp complete as required. Make- Havells cat no. LHFOFWE1TZ1W012 or equivelant in Crompton / Osram / C&S

121) S/I/T/C of 20 watt, 1200mm (±6%) length 6000k, wall mounted LED fitting complete with LED tube & electronic driver etc as required. Make- Havells LHEXBLP7PN1W020 or equivalent in Crompton / Osram / C&S

122) Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

123) Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

123.1) 12 way , Double door

123.2) 16 way , Double door

124) Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

124.1) Single pole.

124.2) Double pole.

125) S/I/T/C of exhaust fan 250 mm 230 V 50 Hz 1400 RPM 10” including connetion etc. complete as required. Make:- Havells / Usha / Bajaj

126) S/I/T/C of heavy duty exhaust fan metalic body 300 mm 230 V 50 Hz 1400 RPM 12” including connetion etc. complete as required. Make:- Bajaj / Usha / Havells

127) Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

128) S/I/T/C of surface mounted bulk head LED fitting upto 1X10 watt. complete as required. Make- Havells or equivalant in Crompton / Osram / C&S

129) Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

130) S/I/T/C of surface mounted Mirror LED fitting upto 1 X 10 watt. complete as required. Make- Havells or equivalant in Crompton / Osram / C&S

Credit of Dismantled items

131) GI Pipe 15 mm to 40 mm dia

132) CI pipe upto 100 mm dia including fittings

133) PVC cistern of any size

134) MS iron frames and MS bars

135) Flush door shutter of various thickness with fittings

136) old PVC tanks of various capaciary

137) Brass stop cock of various size

138) Brass Bib cock of various size

139) Dismantled old MS box with backelite sheet of different size

140) Dismantled of old 1X40 W fittings

141) Dismantled of old ceiling fan of 1200mm / 1400mm

142) Dismantled of old fancy light with glass shade

143) Dismantled of old aluminium / copper wire

144) Dismantled of old SPN DB

145) Dismantled of old DP isolator

146) Dismantled of old SP MCB

147) Dismantled of old 5 A switch

148) Dismantled of old 5 A Socket

149) Dismantled of old 15A Switch

150) Dismantled of old 15A Socket

151) Dismantled of old fan regulator

M/s S.K.Industries

MODERN CONCEPT CONSTRUCTIONS