Spl repair of Bldg in 491 (I) Sup Pl ASC and construction of vocational Lab in Kendriya Vidyalaya at Varanasi Cantt.

Amount

Excavation in trenches in soft/loose soil not exceeding 1.5 M wide and not exceeding 1.5 Mtr deep for foundation etc. or for manhole and getting out including filling bottom surface to required level or slope for laying of pipes/cables complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 M wide and not exceeding 3.0 Mtr deep for foundation etc or for manhole and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation filling, and mass concrete, complete all as specified and directed.

M&L for mild steel TMT bars 6 mm to 8mm dia cut to length bent to shape required incl cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over in reinforcement cut to length bent to shape required incl cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Reinforced cement concrete (design mix) M-25, (using 20 mm graded stone aggregate) as in footing, plinth beams and the like work complete all as specified and directed.

M&L for form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for reinforced cement concrete design mix M-25 (using 20 mm graded stone aggregates) in column complete all as specified and directed.

M&L for formwork to sides of concrete columns, raft beams, sides & soffits of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

M&L for Reinforced cement concrete (design mix) M-25, (using 20 mm graded stone aggregate) slabs supported on walls, roofs beams, and roofs slab, landings, balconies, canopies, deck slabs and in shelves and the like in similar RCC work complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof beam, roof slabs, floor slabs, lintel beam landings and similar work not exceeding 200mm thick horizontal or sloping complete all as specified and directed.

M&L for brick work with old size fly ash bricks straight or curved on plan exc 6m mean radius built in CM 1: 6 complete all as specified and as directed.

Returning filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft soil complete all as specified and directed.

Removing excavated surplus soil not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B-2 (using 40mm graded aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for Virified Ceramic tiles (light shade) 10 mm thick (square/ rectangular) polished , area of each tiles exc .18 sqm but not exceeding 0.36 sqm, in floors and neccessary vertical surface as skrting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bedding in CM (1:4) Complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4, mixed with liquid water proofing compound @ 200ml/50Kg cement complete all as specified and as directed. NOTE: Liquid water proofing compound shall be measured and paid separately under respective item here-in-under.

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L for rendering 15mm thick on other than fair faces of brick work or concrete surfaces in CM (1:6) complete all as specified and as directed.

M&L for preparing new plastered surfaces of wall and applying two coats of acrylic distemper over one coat primer and incl one coat 1 mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of water based premium acrylic smooth exterior emulsion paint over a coat of primer and including 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of old plastered surface of wall incl removal of existing treatment and applying two coats of water based premium acrylic smooth exterior emulsion paint over a coat of primer and including 1mm thick wall care putty complete all as specified and directed.

S&F 25 mm dia stainless steel curtain rod made up of 1.5 mm thick SS 304 Grade Pipe, cut to size and fixed in position including brackets complete all as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantcomplete and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: For WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F 30 mm Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

M&L for Powder coated Anodised aluminium frame for doors/windows/ventilators with one or more rebates including joining cleat for fixing complete all as specified and directed. Note:- Thickness of powder coating shall not be less than 50 micron.

S&F powder coated aluminium chequered grill of anodized section of mesh 50x50mm of 8 mm dia of aluminium bar fixed to frame with 20x2 mm aluminium flat with screw and stainless steel wire cloth 0.36 mm nominal of wire and average width of aperture 1.40 mm complete all as specified and directed.

M&L for 4.8 mm thick sheet glass ordinary quality (area of each pane not exc 0.5 Sqm ) incl rubber beading and jointing cleats complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified & directed.

S&F 150mm Aluminium handles, cast type, anodised of pattern/design as approved by GE/sample kept in GE's office complete all as specified and directed.

S&F 200mm(bolt length) Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 250mm(bolt length) Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S&F 150mm long stainless steel but hinges of approved quality with necessary stainless steel screws etc. complete all as specified and directed.

S&F 140mm Floor door stopper of aluminium alloy body and tongue, with hard drawn steel spring complete all as specified and directed.

M&L for applying high performance polyurethane liquid membrane waterproofing coating on roof in two layer complete as per manufacturer's instructions complete all as specified and directed. The treatment shall be carried out in following steps:- (i) Step 1: clean the roof surface thoroughly to make it free of dust, dirt, grease, and other debris. (ii) Step 2 : Fix the cracks on the surface bed by cutting it into the V section, followed by cleaning and filling with polyurethane-based crack filling compound and white cement in the ratio of 1: 2. (iii) Step 3 : Substrate should be neutralized using the acid application to remove the alkalinity. (iv) Step 4 : All joints, corners and RWP openings shall be properly repaired as per manufacturer's instructions. The material recommended by manufacturer shall be used and cost of same shall deemed included in quoted rates. (iv) Step 5 : Apply a pack of polyurethane primer coat to the surface as an adhesive coat, and allow to dry completely for at least 8 hours.

Contd/... (v) Step 6 : Two successive finishing coats with polyurethane liquid membrane must be applied by brush/roller/spray. Each coating must be dried for at least 12 hours before applying the subsequent coating. After Geotextile fabric of 40 GSM to be applied over first coat while first coat is still wet . This PU coating has to be continued 150 mm up the parapets or walls and at least 100 mm into the rainwater pipes. (vi) The final polyurethane coating is sprinkled with a layer of 300 microns of sand. NOTES: (a) The contractor shall submit a guarantee of 10 years from the date of completion of work for waterproofing treatment along with manufacturer's guarantee. The amount @ Rs. 40 (Forty) per Sqm and subject to min of Rs. 4000/- shall be retained from final bill till the expiry of guarantee period. The contractor at his own option may furnish fix deposit receipt in lieu duly plaged in favour of GE (East) Prayagraj. (b) The water proofing shall be carried out by authorised applicator of manufacturer. The name of applicator shall be got approved in writing from GE within 30 days since commencement of work.

Contd/... (c) Liquid membrane @ 1.5 Kg/Sqm/ 2 coats and epoxy primer @ 0.15Kg/Sqm shall be applied. The liquid membrane shall strictly as per relevant IS code/BIS code. (d) Each stage (preparation of surface, priming, Ist coat and 2nd coat) shall be got approved from GE in writing before execution of successive stage. (e) Production of Purchase vouchers for full quantity duly defaced by Engg-in-charge is mandatory requirement for release of payment. The same shall be recorded in MB.

M&L for vitrified ceramic parking tile 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.11 Sqm, in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bedding in cement mortar (1:4) complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L for rendering 5 mm thick on concrete surface in ceiling in CM 1:3 complete all as specified and as directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying two coats of white wash complete all as specified and as directed.

M&L for preparing old plastered or unplastered surfaces of walls and applying two coats of white wash complete all as specified and as directed.

M&L for preparing old plastered or unplastered surfaces of ceiling and applying one coats of white wash complete all as specified and as directed.

Demolition of brickwork built in cement or cement lime mortar complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in roof kerbs, mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for 40mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in floors finished even and smooth with using extra cement complete all as specified and directed.

M&L for 38mm wide glass dividing strips, 3mm thick and fixed to concrete floor complete all as specified and directed.

Demolition of mud or any other material of any description over RCC roof slab in any thickness and removing the same out side MOD land, complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in roof padding (levelling course) using water proofing compound, finishing the surface fair & even complete all as specified and directed. Note :- Water proofing compound shall be measured and paid under respective item.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F rolled mild steel work in roof trusses (framed), trussed, purlins, crane gantries, pillars, rails and fastenings and heavy bracket framing (beam, tee, angle, channel, Hollow or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W (Gde - E-250) quality - A complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated coloured steel sheet, 0.50mm thick having tensile strength of 550 mpa as in roof covering/cladding to wall fixed with self tapping screws incl taking down old asbstos cement corrugated sheet complete all as specified and directed.

M&L for steel rolling shutter push pull or manual type of thickness 1.25 mm without ball bearing erected in position including top cover, anchoring rod, hasp & staple and including one shop coat of primer incl taking down old rolling shutter complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel /iron surfaces of any description, over 10cm in width or girth, not otherwise described including preparation of surface complete all as specified and directed.

M&L for applying two coat of synthetic enamel paint on old steel /iron surfaces of any description, over 10cm in width or girth, not otherwise described including preparation of surface complete all as specified and directed.

M&L for strengthening of RCC members like col, parapet, facia, ceiling etc. by re concreting through guniting pressure including necessary scaffolding in the following step, complete all as specified and directed:- (a) Removing all loose/ decayed concrete by chiselling for exposing the reinforcement carefully and without disturbing the reinforcement, and clean the surface by sand blasting to make it dust free. (b) Providing addl reinforcement by welding with existing reinforcement to support the existing week/corroded bars. (c) Provide mild steel 12 gauge welded wire mesh of size 100 x100mm size and fixed properly to decayed concrete surface by tack welding/binding. (d) Apply a coat of primer with using Araldite epoxy resins (manufactured by M/s Ciba Geigy Ltd/ FAIR BOND EP/SIKA or other approved manufacture) (e) 35-40mm thick M-20 PCC, type A-0 (using 12.5mm graded stone aggregate) by guniting process using guniting machine at a pressure of 2 to 3 Kg/Sqm mixed with SC plasticiser as per manufacturer's instructions) including stripping, floating with wooden strippers for proper dimension control.

Contd/... (f) 10mm thick plaster in cement mortar 1:4 mixed with liquid water proofing compound @ 3% by weight of cement). NOTE : (i) All surrounding walls, joinery and fitting shall be covered with polythene sheet during work. (ii) Any damage by the contractor shall be repaired/changed without extra cost with entire satisfaction of Engg-in-charge . The decision of Engg-in-charge shall be final and binding in this regard. (iii) Welded mesh & addl reinforcement if required shall be measured and paid separately under respective item.

S&F welded steel wire fabric of weight not exc. 4kg /Sqm complete all as specified and directed.

M&L for 4.0 mm thick frosted sheet glass qrdinary quality and glazing with oil putty ( area not excceing 0.5 Sqm in each pane) including hacking out old brocken glass (any thickness, size, quality or description) from frames complete all as specified and directed.

S&F 0.56mm thick plain, aluminium sheeting, alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed.

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed.

M&L for point wiring for one light point/ fan point/ exhaust fan point controlled by one switch with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed conduit, including non metallic PVC conduit of apropriate size (not less than 20 mm dia) with all accessories, fitting and fixtures, factory made ressessed terminal boxes of reqd size (made of pressed steel sheet not less than 1.6 mm thick) duly painted with two coats of block bituminous paint over a coat of red oxide primer (both side), top cover made of 3 mm thick Phenolic laminated sheet, earthing cable of same discription to common earth drawn in same conduit connected to earth dolly and making good disturbed surfaces and finished to match with existing complete all as specified and directed.

All as per item No 62 above but with 2.5 sqmm cable for one 5/6 Amp socket outlet point on independent board .

All as per item No 62 above but with 1.5 sqmm cable for one 5/6 Amp socket outlet point on same board .

All as per item No. 62 but 3 pin 15 Amp socket outlet on independent board with 2.5 Sqmm cable.

All as per item No 62 above but with 4.0 sqmm cable for one 15/16 Amp socket outlet point independently (for Geyser & AC) controlled by one earth plug and socket box in lieu of sunken box, plate and cover. (Except sunken box, plate and cover) Note: Earth plug and socket box shall be measured and paid seperatly.

S&F switch piano flush type, single pole, one way, 5/6 Amps 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, suitable for 5/6 Amp, 2 module complete all as specified and directed.

S&F Switch Socket Combination 2 in 1, 6 pin, 16 Amps multipurpose type , 240 volts complete all as specified and as directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface Bakelite sheet 63.50mm dia complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F fan regulator, stepped type, 120 watt single phase complete all as specified and directed.

S&F LED retrofit lamp of capacity 9 watt, power backup up to 4 hrs B-22 holder base with polycarbonate body and aluminium heat sink warm white complete complete all as specified and directed.

S&F sheet metal enclosure vertical DB TPN, double door 6 way 415 Volts with 100 Amp ratred insulated bus bars and neutral bar including provn of 1 Nos. 100 Amp incoming MCCB, 3 pole and (6+6+6) outgoing Nos. MCB SP 5 to 32 Amp prewired complete all as specified and directed.

S&F sheet metal enclosure/Distribution board for MCBs, double door type, epoxy powder coated, factory made, Single Pole and Neutral (SPN), 8 way 240Volts with 200 Amps rated bus bar, with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB SPN, 40 amps, 240V, 10KA, 'B' curve complete all as specified and directed.

S&F MCB SP, 6-32 Amps, 240V, 10KA, C curve complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below GL) connected with GI wire 4.0 mm dia as earthing lead by means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe (ISImark) light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm diaTMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing including dismantling of old ineffective earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth strip and protection pipe upto 7.5 meter beyond the earth plates electrode)

S&F LED tube light fitting 1 x 20 watt, decorative , ultra slim round profile LED lighting fixture with co extruded polycarbonate body, environmental friendly , energy efficient complete with all accessories, prewired and making connection with and including 23/0.0076 flexible three core copper cabel (from connector to ceiling rose) not more than 1.2 mtr, fixed on wall firmly complete all as specified and directed.

S&F sheet metal enclosure, single pole and neutral with a two pin and earth plug and socket and 1x 20Amp SP MCB complete all as specified and directed.

M&L for sub main wiring with two single core FRLS PVC insulated unsheathed multistranded copper conductor of size 6 Sqmm nominal cross sectional area and one run as continuous earth wire of similar description, drawn in and including 20mm dia 'medium grade' PVC concealed conduits (with fittings) incl taking down the old unserviceable wiring complete all as specified and directed. NOTE: Two run of main wire and one run of earth wire with conduit shall measured as One unit length.

Supply, installation, testing and commissioning of Split type air conditioner unit 1.5 Ton capacity (indoor and outdoor) having digital inverter rotary type compressor (single phase unit both), 220V-240V, 50Hz, 5 star rating and EER 3.2 with cordless remote control, complete all as specified and directed. Note: Cost of copper tube up to 5 meter distance deemed to be included in quoted unit rate.

Supply, laying and testing (in replacement) 1.1_KV XLPE insulated PVC sheathed armoured Aluminium LT cable with stranded aluminium conductor of size 10 sq mm 4 core complete all as specified and directed.

S&F LED integral round shape surface/recess mounting high power LED luminaire, dome shape opal diffuser lamp of capacity 12w complete complete all as specified and directed.

S&F exhaust fan heavy duty, steel body with steel blads, 300mm sweep, single phase 240 volt including making electrical connection and writing MES No with black paint incl taking down carefully existing exhaust fan by disconnecting all electrical connection, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed. (NOTE: Fans shall be deposited by the contractor in AGE E/M yard).

S&F BLDC ceiling fan, 1200 mm sweep, BEE 5 star rated, 230 V, 50 Hz, single phase AC supply with remote or electronic regulator unit for speed control and all remaining accessories and writing MES No with black paint complete all as specified and directed.

S&F in repair sheet metal enclosure/ Distribution board for MCBs, double door type, epoxy powder coated, factory made, Triple Pole and Neutral (TPN), 4 way 415Volts with 200 amps rated copper bus bar, with enclosure blank plates for unused way complete all as specified and directed.

S&F in repair sheet metal enclosure/ Distribution board for MCBs, double door type, epoxy powder coated, factory made, Single Pole and Neutral (SPN), 4 way 415Volts with 200 amps rated copper bus bar, with enclosure blank plates for unused way complete all as specified and directed.

S&F in repair MCB SP 240 Volt 6 to 32 Amp ISI marked conforming to "B" curve, breaking capacity 10 KA complete all as specified and directed.

S&F in repair Isolator/ MCB SPN 40 Amp ISI marked conforming to "B" curve, breaking capacity 10 KA complete all as specified and directed.

S&F in repair MCB TPN 63 Amps, 415V ISI marked conforming to "B" curve, breaking capacity 10 KA complete all as specified and directed.

S&F in repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply, laying and testing 1.1_KV XLPE insulated PVC sheathed armoured Aluminium LT cable with stranded aluminium conductor of size 25 sq mm 3.5 core inclusing taking down existing Old/Unserveciable cable complete all as specified and directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item.

M&L for sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand up to 18 cm thick and consolidation complete all as specified and directed. Note : Punned thickness i.e 18 cm shall only be measured for payment purpose.

Supply and laying dry well burnt locally available brick sub class 'B' old size bricks laid flat with width equal to the length of whole bricks over cable as cable protection complete all as specified and directed.

M&L for boring hole for passing cable through / insertion of 40/50mm dia GI pipe under PCC road/ taxi track/ runway/ hard standing up to the depth 450mm to 1200 mm complete all specified and as directed. NOTES :- (i) Cost of equipments, tools & plants, material required for boring shall deemed to be included in quoted unit rates. (ii) GI pipe shall be measured and paid separately under respective item.

S&F for 40 mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hard standing complete all as specified and directed. NOTE : Excavation and earth work shall be measured & paid separately.

L.K.R.TIWARI CONSTRUCTION (BID ID -3450218)