PROVISION OF CERTAIN SPECIAL REPAIR WORKS AT CH (CC) IN THE AREA OF AGE E/M HOSPITAL UNDER GE E/M LUCKNOW.

Amount

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in Soft/ Loose soil for foundation, trench of cables, pipes etc or for shaft, wells, manholes n exc 10 Square Metre on plan and getting out including trimming the sides and forming bottom surfaces to required levels, complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each, excavated soil in trenches after the cables have been laid and tested, complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.50 meter above the starting point , complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete (1:5:10), type E-2, using 40 mm graded mechanically crushed stone aggregates as in sub base 100 mm thick in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) , complete all as specified and directed by the Engineer in Charge.

Plain cement concrete type C1 (1:3:6), using 20 mm graded crushed stone aggregate,75 mm thick , as in path / plinth protection/paving laid in slope in 1:30 in panels n exc 2m long concrete surfaces finished even and smooth without using extra cement including making joints between panel to panel and filling the same with bitumen mastic bitumen & sand mixture in a ratio 1:3 in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) , complete all as specified and directed by the Engineer in Charge.

Plain Cement Concrete type B1 1:2:4 (using 20 mm graded stone aggregate) as in lintel upto 1.5 metre clear span, cills,steps, seismic and other band,coping, covering bed plates and likep including weathering, slightly rounded or chamfered angles and throating including necessary formwork , complete all as specified and directed by the Engineer in Charge.

Brickwork with Brickwork with Fly ash bricks (bricks shall be burnt clay flyash building bricks as per IS- 13757), straight or curved on plan exceeding 6.0 m mean radius built in cement sand mortar 1:6 in and including demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc ,complete all as specified and as directed by Engineer -in-Charge

Taking down Chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 Sq. m each, and making good the disturbed Surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sq. m but not exceeding 4.00 Sq. m each, and making good the disturbed surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description not exceeding 1 Sq. m each, from chowkhat, complete all as specified and directed by the Engineer in Charge.

Taking down shutters of any description exceeding 1 Sq. m but not exceeding 2 Sq. m each, from chowkhat, complete all as specified and directed by the Engineer in Charge.

Plain, solid, straight chowkhats & frames of 2nd class HW wrought, framed rebated on the solid, rounded or chamfered, put together with glue & pinned at joints including preparation of back of chowkhat & treated with coal tar ,complete all as specified and directed by Engineer-in- Charge.

Hold fast, band straps, supports ,Wind ties for stay securing bolts, posts & struts in fencing including cutting cutting tops to shape as directed, drilling holes, notching for wire, etc and similar work conforming to Fe-290 Gde E-165 , complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate for fixing of hold fast and making good ,complete all as specified and directed by Engineer-in- Charge.

Factory made 35 thick glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (divided into squares, with plain,chamfered or rounded,mitred and rebated sash bars,any numbers fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, complete all as specified and directed by the Engineer in Charge.

Factory made flush shutters 30 mm thick, solid core construction , with block board core and plywood face panels, commercial type on both sides , complete all as specified and directed by the Engineer in Charge.

Factory made flush shutters 25 mm thick, solid core construction , with block board core and plywood face panels, commercial type on both sides including 60mm thick leeping on edges , complete all as specified and directed by the Engineer in Charge.

Butt hinges 100 mm size ,extruded bradd with mild steel hinge pin, bright polished fixed type B11 ,complete all as specified and directed by the Engineer in Charge.

Aluminium alloy handles of size 125 mm, cast type anodized ,complete all as specified and directed by Engineer-in- Charge.

Aluminum anodizes barrel tower bolts of extuded section and fixed of 200 mm long size (length of bolt), complete all as specified and directed by Engineer-in-Charge

Aluminum alloy, anodized, sliding door bolt with hasp staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed length of bolt 250mm, bolts not less than 12mm dia with and including a minimum of 6 bolts not,four on bolt plate and two on staple plate complete (ISI marked ) , complete all as specified and directed by Engineer-in-Charge.

Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery ,complete all as specified and directed by Engineer-in- Charge.

Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in steel window clips and wooden beading in wooden joinery fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Continuous (Piano) hinges, width of flaps (when open ) 30mm, mild steel bright finish or electro galvanised,ISI Marked, complete all as specified and directed by Engineer-in- Charge.

Double action spring hinge mild steel of 150 mm size with steel wire spring, stove enamelled black , complete all as specified and directed by Engineer-in- Charge.

Fancy type drapery curtain rod made of mild steel duly PVC sleeved of 20 mm dia fixed as in repair, complete all as specified and directed by Engineer-in- Charge.

Brackets for fixing cutain rods of any dia powder coated fixed as in repair, complete all as specified and directed by Engineer-in- Charge.

Factory made steel windows with side hung shutter, box type hinges, steel handle 125mm long (fabricated of Z-Section & welded/riveted to shutter in lieu of locking handle), steel peg stay, 2 Nos. tower bolts 100mm on each leaf duly welded, complete with glazing bars, complete all as specified and directed by Engineer -in-charge. Note: Supply & fixing of sheet glass shall be measured and paid separately.

Factory made steel windows with side hung shutter, box type hinges, steel handle 125mm long (fabricated of Z-Section & welded/ riveted to shutter in lieu of locking handle), steel peg stay, 2 Nos. tower bolts 100mm on each leaf duly welded, complete without glazing bars but including MS flat for fixing wire mesh/cloth, complete all as specified and directed by Engineer -in-charge. Note: Supply & fixing of wire mesh/ cloth shall be measured and paid separately.

M S work as Framed works such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes,framed guard bars barred iron doors ladders, framed balusters walk ways railing, framed work of water tanks, framed and hung as gates including pintle hinges, stops, hand made sliding sliding bolts etc ,drilling bolting or reveting etc and similar work conforming Fe-290 Gde E-165 ,complete all as specified and directed by Engineer-in- Charge.

Preparation of new wooden surfaces of any description, exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer , complete all as specified and directed by Engineer-in-charge.

Preparing new steel surface of any description, over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer , complete all as specified and directed by Engineer-in-Charge.

Sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, , complete all as specified and directed by Engineer-in- Charge.

Figured glass 3 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, complete all as specified and directed by Engineer-in- Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares exceeding 0.5 Sq. m in each pane, including Hacking out old broken glass panes of any thickness, size ,quality or description from wooden frames , glazed with putty or fixed with beads ,complete all as specified and directed by Engineer-in- Charge.

First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in coloured cement to match the shade of tiles including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) rubbish off the premises ,complete all as specified and directed by Engineer-in- Charge.

Machine cut Kota stone slab 20 -25 mm thick (of size not less than 55 cm x 55 cm) laid as in flooring in designer pattern with marble stone with neat cement slurry @ 3.00 kg/Square metre over and including 20 mm thick (average thickness) cement screed (1:4) base, laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) in and including demolition of stone slab & tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar ,complete all as specified and directed by the Engineer in Charge.

Machine cut Kota stone slab 18-20 mm thick as in skirting, over and including 10 mm thick rendering of cement mortar (1:4), laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) in and including demolition of stone slab & tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar ,complete all as specified and directed by the Engineer in Charge.

Granite stone slab ( Black colour) 18-20 mm thick, work (table rubbed and polished and grinding) as in flooring including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed of 15 mm thick in CM 1:6 in and including demolition of stone slab & tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar ,complete all as specified and directed by the Engineer in Charge.

Factory made Machine pressed PCC intelocking tiles 60mm thick M-35 Grade (rubber laminated finish) of size and shape as approved, laid dry over and including sand not less than 40 mm thick, interstices filled in floors/pathway , laid bedded and pointed in cement mortar ,complete all as specified and directed by the Engineer in Charge.

Rendering 15mm thick on fair faces of brick wall or concrete surface in cement mortar 1:4 finished even and fair without using extra cement using in and including integral water proofing compound 2 % by weight of cement ,complete all as specified and directed by Engineer-in- Charge.

Rendering 10mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement ,complete all as specified and directed by Engineer-in- Charge.

Rendering 5mm thick on ceiling,sides of roof beam and soffits of roof slab in cement mortar 1:3 finished fair and even without using extra cement ,complete all as specified and directed by Engineer-in- Charge.

Rendering 15mm thickon fair faces of brick wall or concrete surface in cement mortar 1:4 finished even and fair without using extra cement using in and including integral water proofing compound 2 % by weight of cement including taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. ,complete all as specified and directed by Engineer-in- Charge.

Rendering 10mm thick on other than fair faces of brick wall or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement in and including taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. ,complete all as specified and directed by Engineer-in- Charge.

Prepartion of newly plastered or unplastered surfaces of ceiling and applying three coat of white wash ,complete all as specified and directed by Engineer-in- Charge.

Preparation of newly plastered surfaces and applying two coats of oil bound disemper over one coat of oil base primer on walls surface over and including a thin layer of wall care putty ,complete all as specified and directed by Engineer-in- Charge.

Preparation of newly plastered or unplastered surfaces of walls by brooming down and priming plastered and other surfaces with and applying two coats of cement base paint over a coat of cement paint primer (before application of cement base paint) ,complete all as specified and directed by Engineer-in- Charge.

Complete removal of existing treatment including prepartion of unplastered old surfaced and distempering walls with two coats of oil bound distemper white or tinted over a coat of oil base primer on wall sufaces including a thin layer of wall care putty ,complete all as specified and directed by Engineer-in- Charge.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, applying two coats of Apex ( Asian Paint) / Weather coat (Berger) ,complete all as specified and directed by Engineer-in- Charge.

Preparation of old plastered or unplastered surfaces of walls by washing, rubbing down & stopping etc, applying one coat of Apex ( Asian Paint) / Weather coat (Berger) ,complete all as specified and directed by Engineer-in- Charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm but n.exc 20 cm girth in stone concrete block/ slab wall/ concrete floor ,complete all as specified and as directed by Engineer -in-Charge

Steel water tubeing, 15 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down steel water tubing and connections ,complete all as specified and directed by Engineer-in- Charge.

Steel water tubing, 20 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down steel water tubing and connections ,complete all as specified and directed by Engineer-in- Charge.

Steel water tubing, 25 mm bore medium grade, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down steel water tubing and connections ,complete all as specified and directed by Engineer-in- Charge.

Wash basins with standard padestal pattern, vitreous china, white, flat back of size 550x400 mm including brackets and cutting for and pinning in ends in brackets or erecting stand ,32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia LDPE waste pipe of pressure rating 6 Kg/Cmsq and including new M S brackets including waste coupling of PTMT (half or full threaded) for 32/40mm dia fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Vitreous china wash down water closet pan (padestal pattern) with P or S trap white including fixing with bolt in floor with and including 10 litre capacity low level flushingcistern and flush pipe connecting to WC with cistern with and including plastic water closet seat, white closed pattern with flat bottom and cover and mild steel chromium plated hinging device with and including CP spray jet and fixed as in repair , complete all as specified and directed by the Engineer in -Charge

PVC valveless , syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm dia for low level , complete all as specified and directed by the Engineer in -Charge

PVC connection of PTMT ,non corrosive with nuts and washers on both ends,450mm long suitable for 15 mm bore fixed , complete all as specified and directed by the Engineer in -Charge.

Tubular towel rail 20mm dia D type,brass chromium plated 60 cm long between flanges ,complete all as specified and as directed by Engineer-in- Charge.

Bib taps for 15 mm bore pipe, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repair , complete all as specified and directed by the Engineer in -Charge

Stop valves 15 mm bore chromium plated fancy type concealed type ISI Marked, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed as in repair, complete all as specified and directed by the Engineer in -Charge

Angle valve two way cast copper alloy,chromium plated , fancy type with cup (concealed type) for 15 mm bore dia fixed as in repair , complete all as specified and directed by the Engineer in -Charge

Pillar taps, fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe fixed as in repair, complete all as specified and directed by the Engineer in -Charge

Rotational moulded PVC, double layered, water storage tanks of capacity 1000 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. but excluding ball valve in and including dismantling PVC water tanks exc 500 ltr but n. exc 1000 ltr capacity by disconnecting existing water connection and removal from site ,complete all as specified and directed by Engineer-in- Charge.

Brass valves, high pressure, with polythene float and fly nut ,20mm dia , screwed for iron pipes or brass ferrule and fixed in PVC OHT tanks ,complete all as specified and directed by Engineer-in- Charge.

Gun-metal, globe or gate valves 20mm dia , with iron wheel head, screwed both ends for iron pipe and fixed to 20mm dia GI tube ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 110mm bore single socketed in any length with ruber rings joints laid in trenches or in floors in and ncluding taking down old pipe including fittings ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 110mm bore single socketed in any length with ruber rings joints fixed to walls with necessary brackets in and ncluding taking down old pipe including fittings ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 110mm bore junction single, (single Tee) equal or unequal with access door fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) bends any radius 110mm bore fixed as in repair complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) Vent cowl 110mm bore fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 75mm bore single socketed in any length with ruber rings joints laid in trenches or in floors in and ncluding taking down old pipe including fittings ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 75 mm bore single socketed in any length with ruber rings joints fixed to walls with necessary brackets in and ncluding taking down old pipe including fittings ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 75mm bore junction single, (single Tee) equal or unequal with access door fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) bends any radius 75mm bore fixed as in repair complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) pipes 150mm bore single socketed in any length with ruber rings joints laid in trenches or in floors in and ncluding taking down old pipe including fittings ,complete all as specified and directed by Engineer-in- Charge.

Cutting into walls of existing manholes for connecting new drain pipe 150 mm dia bore, making good to wall in CM (1:3)/ PCC (1:2:4) after inserting pipe, cutting out benching & forming branch channel (1/2) round or (3/4 section) in cement concrete (1:2:4) type B-1, reforming benching as required and rendering smooth finished, including removal of rubbish outside MoD land, complete all as specified and directed by the Engineer-in-Charge.

Plain cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested, complete all as specified and directed by the Engineer-in-Charge.

Salt- glazed stoneware drain pipe grade ‘A’ 150 mm bore, ISI marked jointed with cement mortar, laid in trenches and tested including pipe fittings such as bend, junction etc. of same grade , complete all as specified and directed by the Engineer-in-Charge.

Water proofing treatment on roof surfaces shall be carrierd out with the specification as below ,complete all as specified and directed by Engineer-in-Charge :- (a) Complete removal of existing water proofing treatment of any type from roof surface and removing/ disposing out of the premises as directed . (b) 15mm thick screed plaster on RCC slab CM 1:4 by using in and including liquid water proofing compound @ 3% by weight of cement. (b) Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces and preparation of the surfaces. (c) Supply and laying 3mm thick APP water proofing membrane reinforced with non woven polyster matt laid using butane torch by torch on application with a side lap of 10cm and 15cm end lap weighing not less than 3.0 kg/sqm. (d) Providing 40mm thick brick tiles 230mm X 115mm laid on cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement tiles are bedded. Note : The tiles shall be laid to the slop to avoid stagnation of water.

Suplying, laying, testing Cast iron pipes with flanged ends, centrifugally cast, class A, in any length laid in trenches of 150 mm dia in and including taking out of existing unserviceable CI pipe , complete all as specified and directed by Engineer-in-Charge.

Suplying, laying, testing Cast iron pipes with flanged ends, centrifugally cast, class A, in any length laid in trenches of 80 mm dia in and including taking out of existing unserviceable CI pipe , complete all as specified and directed by Engineer-in-Charge.

Supplying, laying, jointing and testing of galvanised steel water tubing 15 mm bore, medium grade, with all GI fittings and laid in trenches in and including taking up or down steel water tubing and connections ,complete all as specified and directed by Engineer-in- Charge. Note : Excavation & earthwork shall be measured & paid separately under appropriate item of this BOQ.

All as per item no 85 above but of 25 mm bore

All as per item no 85 above but of 40 mm bore

All as per item no 85 above but of 50 mm bore

All as per item no 85 above but of 80 mm bore

Gun metal gate valve of size 20 mm bore, Class -1, ISI marked with iron wheel head, screwed both ends for iron pipe in and including taking up or down old unservicable gate valve ,complete all as specified and directed by Engineer-in- Charge. Note : Excavation & earthwork shall be measured & paid separately under appropriate item of this BOQ.

All as per item no 90 above but of 25 mm bore

All as per item no 90 above but of 40 mm bore

All as per item no 90 above but of 50 mm bore

Run lead joints suitable for spigot & socketed CI Pipe and caulking the joints properly for avoiding leakage etc including burning out lead joint in position, removing & recovering old lead & necessary earth work excavation as required for 80 mm dia bore fixed as in repair for new/old pipe lines of fittings , complete all as specified and directed by Engineer-in-Charge.

All as per item no 94 above but of 100 mm bore

Flanged joints complete with rubber or fibre board gasket for new/old pipe lines including nut bolts & washers etc. of 80mm bore size of water mains/fittings ,complete all as specified and directed by Engineer-in-Charge.

All as per item no 96 above but of 100 mm bore

Cutting of existing Cast Iron pipes water main in position for insertion of new tee for branch connection by inserting CI fittings etc for 80 mm bore pipe including necessary excavation & earth work and dewatering of residual water,complete all as specified and directed by Engineer-in-Charge. Note : CI fittings and joints shall be measured and paid separately under appropriate items)

All as per item no 98 above but of 100 mm bore

Boring under road for laying of GI pipe of size 15 mm to 25 mm bore ,complete all as specified and directed by Engineer-in-Charge.

All as per item no 100 above but of 40 to 50 mm bore

All as per item no 100 above but of 80 to 150 mm bore

Sluice valve of size 80 mm bore connection & testing 'ISI marked' both ends flanged and drilled cast iron body class PN-1.6 conforming to IS-14846/2000 complete with gun metal spindle including necessary nut bolts etc including taking down of unserviceable Sluice valve ,complete all as specified and directed by Engineer-in-Charge.

All as per item no 103 above but of 100 mm bore

All as per item no 103 above but of 150 mm bore

Cutting existing steel tubing for alterations or additions (Each cut measured) for 20 mm bore ,,complete all as specified and directed by Engineer-in-Charge.

All as per item no 106 above but of 25 mm bore

All as per item no 106 above but of 40 mm bore

All as per item no 106 above but of 50 mm bore

Construction of valves pit chamber of size 900x900x900mm (internal dimension), using PCC (1:4:8) 40 mm graded stone aggregate for foundation 15 cm thick, 23 cm thick wall in CM (1:4) 10 mm thick rendering all around the brick work with 1:6 cement mortar PCC (1:2:4) type B1 coping with 20 mm graded agregate for grouting MS frame including 4 mm thick MS top sheet cover with locking arrangement including 50 mm pad lock with double key arrangement, MS frame out of 40 x 40 x 5 mm thick angle iron including paintaing of steel surface with two coats of synthetic enamel paint over a coat of red oxide primers finishing coat including necessary excavation in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 mtrs ,complete all as specified and directed by Engineer-in-Charge.

All as per item no 110 above but of of size 600x600x600mm

Point wiring for one light/fan point controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly and make wall surface as existing same colour in and including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing,complete all as specified and directed by Engineer-in- Charge.

Point wiring for one socket outlet point 5 amps on independent board controlled by one, one way switch by using 1.5 Sq mm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including PVC concealed conduits and conduit accessories/fittings, pressed steel terminal switch boxes, 3 mm thick Bakelite sheet top cover (ISI Marked) fitted with Chromium plate brass screws washers and 1.5 Sq mm nominal cross sectional area multistranded copper conductor green PVC insulated unsheathed earth wire and connecting to earth dolly in and including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing ,complete all as specified and directed by Engineer-in- Charge.

All as per item no 113 hereinbefore but one socket outlet point on same baord with other switches with 1.5 sq mm single core multistranded PVC insulated FRLS cable including 1.5 sq mm single core multi stranded copper cable used as continuous earth wire ,complete all as specified and directed by Engineer-in- Charge.

Point wiring for 15 amps socket point controlled by one, one way switch using 2.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated FRLS unsheathed cables in and including PVC concealed conduit and conduit fittings including pressed steel terminal switch boxes and 3 mm thick plate for fixing of switches/sockets and fitted with Chromium plated brass screws & washers and1.5 Sq mm nominal cross sectional area multi stranded copper conductor, PVC insulated unsheathed earth wire and connected to earth dolly in and including taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc. to match with the existing good disturbed surfaces of walls, floors etc. match with the existing ,complete all as specified and directed by Engineer-in- Charge.

Switch piano flush type polycarbonate, SP,5/6 Amps, one way ,complete all as specified and as directed by Engineer-in- Charge.

Switch piano flush type polycarbonate , SP, 16/20 Amps, one way ,complete all as specified and as directed by Engineer-in- Charge.

Socket out let 2 in 1 socket 5 pin polycarbonate , (6 Amps) flush type controlled by one switch complete all as specified and directed.

Socket out let polycarbonate 6 pin, 20 Amps ,complete all as specified and as directed by Engineer-in- Charge.

Ceiling rose, Pilot 3 Plate ceiling rose 6A ,complete all as specified and as directed by Engineer-in- Charge.

Ceiling fan step regulator 120 Watt - 02 module of Indian standard ,complete all as specified and directed by Engineer-in- Charge.

Switch socket combination 2 in 1 , 3 pin , 5 & 15 amp flush type universal ,complete all as specified and as directed by Engineer-in- Charge.

Distribution box epoxy powder coated ,SPN 4 way, 240 V, with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door as in replacment ,complete all as specified and directed by Engineer-in- Charge.

Distribution box epoxy powder coated ,SPN 8 way, 240 V, with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door as in replacment ,complete all as specified and directed by Engineer-in- Charge.

Distribution box epoxy powder coated ,SPN 12 way, 240 V, with 200 amps rated bus bar, 240 Volts for MCBs, grouted flush to walls complete with IP 43 and metal double door as in replacment ,complete all as specified and directed by Engineer-in- Charge.

MCB SP, 6 to 32 Amps, 240 Volts to be housed in DBs of Proper and suitable size cable lugs to be fixed with MCBs as in replacment ,complete all as specified and directed by Engineer-in- Charge.

MCBs SPN/ Isolator, 40 Amps, 240 Volts to be housed in DBs Proper and suitable size cable lugs to be fixed with MCBs as in replacment ,complete all as specified and directed by Engineer-in- Charge.

Sub main wiring (concealed type ) with two single core 4 Sqmm FRLS PVC insulated and unsheathed 1100 volts grade cables with stranded copper conductor cable drawn through in and including 25 mm dia rigid non metallic PVC conduit and conduit accessories including one single core 4 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dully complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface in and including taking down old unservicable sub main wiring , complete all as specified and directed by Engineer-in-Charge. Note : (i) 2 run of 4 Sqmm ,1 run of PVC conduit & 1 run of 4 Sqmm cable will be measured as single run. (ii) Extra length of cables/wire required for connection to MCBs shall not be measured and paid separetly the rate quoted by contractor per unit shall be deemed to be included in the quoted rate of this item.

Sub main wiring (concealed type ) with two single core 10 Sqmm FRLS PVC insulated and unsheathed 1100 volts grade cables with stranded copper conductor cable drawn through in and including 25 mm dia rigid non metallic PVC conduit and conduit accessories including one single core 6 Sqmm FRLS PVC insulated unsheathed stranded copper earth cable connected to common earth dully complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface in and including taking down old unservicable sub main wiring , complete all as specified and directed by Engineer-in-Charge. Note : (i) 2 run of 10 Sqmm ,1 run of PVC conduit & 1 run of 6 Sqmm cable will be measured as single run. (ii) Extra length of cables/wire required for connection to MCBs shall not be measured and paid separetly the rate quoted by contractor per unit shall be deemed to be included in the quoted rate of this item.

Earthing complete with Galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to G I earth strip 4 dia G I wire by means of brass bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, pit cover of precast RCC (1:2:4), type B-1, reinforced XPM of weight not less than 4 kg/ Sq.m and MS frame etc. , complete all as specified and as directed by Engineer-in-Charge. Note :- (i) The unit rate includes earth lead and protection pipe up to maximum 7.5 metre from earth plate to earth point/test point. (ii) Earth pit shall be constructed minimum 0.5 metre away from earth.

Distribution Board TPN with and including of DPX MCCB 35 KA 160 Amps MCCB FP, as incomer and SP/TPN MCBs as outgoing protection class IP 54 , 4 way (DPX 160+12) with metal double door of metal double door as in replacement, complete all as specified and directed by Engineer-in-Charge. Note :- FP MCCBs 35 KA 160 Amps 1 No and 24 Nos MCB SP 32 Amps 230 Volts and Blanking plate shall be measured and paid under this this item

Flexible copper cable three core 1.5 sqmm suitable for connection of CFL fittings 2x36/3x36 watts or FTL fittings of any type , complete all as specified and directed by Engineer-in-Charge

Lamp holder, PVC/polycarbonate type with cord grip cap suitable for pendant fittings , complete all as specified and directed by Engineer-in-Charge

LED Bulk head fitting with clear glass complete with electronic control gear , with and including making connection , complete all as specified and directed by Engineer-in-Charge

LED tube light 20 watt 4 feet retro Bar Professional WH 5700K/CW 6500Kble FTL & Supply and fixing battern fitings suiatable for 20 W LED tube with single side connection Ultra bright, glass shell, glare free, wide angle, single side . prewired including providing connection of size 23/.0076 of required length form ceiling rose to the tube light fitting in and including taking down old unserviceable FTL T/L rod any watt , complete all as specified and directed by Engineer-in-Charge

Barttern fiting for LED tube rod 20 watt pre wired including connection in and including taking down old unserviceable FTL T/L rod any watt , complete all as specified and directed by Engineer-in-Charge

Bulk head light fitting 18 watt make philips Ultron 17-Watt (Cool White, Round) or equivalent of other , complete all as specified and directed by Engineer-in-Charge

M/s Reliable Electromech Systems

SB Singh and co.