NIT No. 1077/TC/25-26

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 meters including removal and disposal of top organic soil not exceeding 150 mm in thickness if required and as per relevant clauses of section-200. (A) In area of light jungle

Dismantling of flexible pavements and disposal of dismantled materials including all leads, stacking serviceable and unserviceable materials separately and as per relevant clauses of section-200. (A) Bituminous courses

meter

Construction of RCC drain/chamber cover, placing in position, providing shuttering and concreting by using concrete mixer, compaction by vibration etc complete as per drawings and technical specifications excluding reinforcement. with RCC M-20

Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in drain/ cover/ chamber complete as per Drawing and Technical Specifications.

Granular Sub-base as per table 400-1 Construction of granular sub-base by providing graded Material, , carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface watering, rolling and compacting with vibratory power roller at OMC to achieve the desired density, complete as per clause 401 Plant mix method (with Mechanically crushed stone only) (b) For Sub-base cum drainage layer or upper sub-base with (i) Grading-V Material

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per clause 406.)

Prime coat (Providing and applying primer coat with oil based bitumen emulsion (SS-1, grade confirming to IS:8887) on prepared surface of granular Base including clearing of road surface and spraying primer using mechanical means as per clause 502. i) on WBM/WMM surface @0.85 Kg/sqm.

Tack coat Providing and applying tack coat with bitumen emulsion (RS-1, grade confirming to IS:8887) using emulsion pressure distributor on the prepared bituminous/granular surface cleaned with mechanical broom and as per clause 503. (ii) Granular surfaces treated with primes @ 0.30 kg /Sqm

Dense Bituminous Macadam (Providing and laying bituminous concrete with minimum 100-120 TPH capacity Batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder @ 4.0 to 4.5% by weight of total mix of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No.505 complete in all respects.) (B) With mechanical paver finisher (i) for Grading-I (37.5 mm nominal size bitumen content 4.00%)

Dense Bituminous Macadam Add extra to the Rate of Dense Bituminous Macadam with bitumen, if Bitumen Grade VG-40 is used instead of Bitumen Grade VG-30 in the items above. (@ 4%)

Bituminous Concrete (Providing and laying bituminous concrete with minimum 100-120 TPH capacity Batch type HMP using crushed aggregate of specified grading, premixed with bituminous binder @ 5.0 to 6.0% by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507complete in all respects) (B) With Mechanical paver (iii) for Grading II (13.2 mm nominal size aggreagate) with bitumen 6.0%

Add extra to the Rate of Bituminous Concrete with bitumen, if bitumen Grade VG-40 is used instead of Bitumen Grade VG-30 in the items above (@ 4%)

Retro- reflectrorized Traffic signs as per clause 801 (Providing and fixing of retro-reflectrorized cautionary, mandatory and informatory sign over refletorized sheeting of required grade conforming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium / Aluminium Composite Material (ACM) sheeting, including flurocarbon coating applied on exposed surface of aluminium to ensure corrosion resistance, supported on a mild steel frame of size 40 x 40 x 5 mm and mild steel angle iron post 75 mm x75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paints or powder coatingand the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.) (I) With Aluminium sheeting (A) made of Class-A high Intensity micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-2022 (for ODR & Village Roads) (a) With Aluminium Sheeting of 2 mm thickness (i) 900 mm equilateral traingle

(for ODR & Village Roads) (a) With Aluminium Sheeting of 2 mm (iii) 900 mm high octagon

(for ODR & Village Roads) (b) With Aluminium Sheeting of 1.5 mm (ii) 600mm circular

(for ODR & Village Roads) (b) With Aluminium Sheeting of 1.5 mm (iii) 600mm x 500 mm rectangular

Direction and Place Identification signs upto 0.9 sqm size board as per clause 8.1 (Providing and fixing of retro-reflectrorized cautionary, mandatory and informatory sign over refletorized sheeting of required grade conforming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium / Aluminium Composite Material (ACM) sheeting, including flurocarbon coating applied on exposed surface of aluminium to ensure corrosion resistance, supported on a mild steel frame of size 40 x 40 x 5 mm and mild steel angle iron post 75 mm x75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paints or powder coatingand the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.) (I) With Aluminium Sheeting of 2 mm thickness (C) Made of Class-A High Intensity micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-2022 (for ODR & Village Roads)

Direction and Place Identification signs with size more than 0.9 sqm size board as per clause 8.1 (Providing and fixing of retro-reflectrorized cautionary, mandatory and informatory sign over refletorized sheeting of required grade conforming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium / Aluminium Composite Material (ACM) sheeting, including flurocarbon coating applied on exposed surface of aluminium to ensure corrosion resistance, supported on a mild steel frame of size 40 x 40 x 5 mm and mild steel angle iron post 75 mm x75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paints or powder coatingand the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.) (I) With Aluminium Sheeting of 2 mm thickness (C) Made of Class-A High Intensity micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-2022 (for ODR & Village Roads)

Providing & Fixing Hazard Marker Partial Reflective hazard marker as per clause 15.66 of IRC 67-2022, made of 16 gauge (1.6 mm) thick mild steel sheet Confirming to IS:2062 Painted with one coat of Zinc Chromate Stoving Primer and two coats of Black Stove Enamel (Oven Baked) painted with 10 cm alternative bands of yellow Retro- Reflective Sheeting of Micro Prismatic Grade pasted as per IRC:79 and black paint, including back frame made of angle iron 25x25x3mm mounted over one MS angle Iron post of size 50x50x6mm of 1.65 meter long duly painted with synthetic enameled paint block including bolts and fixing the same in M-15 concrete black including bolts and fixing the same in M-15 concrete black of size 30x30x30 cm Including transportation etc. Complate (I) One Way Object Hazard Marker Size 300x900mm (B) Made of Class-B Micro Prismatic Grade Sheeting of Type XI (for National MDR, ODR & Village Roads)

Overhead Signs as per Clause 8.2 Providing and erecting overhead sign including fixing of retro-reflectrorized sheeting digitally printed of Class-C micro Prismatic Grade Sheeting of Type-XI confirming to ASTM D 4956 including covering with transparent sheeting (lamination sheeting) to protect from fading and damage due to wheather effect as per IRC:67-2022 made of retro-reflective type sheeting vide clause 801.3 fixed over Aluminum sheeting of overall thickness 2mm including application of fluorocarbon coating applied on exposed surface of aluminum to ensure corrosion resistance, supported on a mild steel back frame of ISA 40 x 40 x 5 mm with un supported length of sheet not exceeding 0.9m in any direction and required diagonal members including cost of sign boards and their back frames and painting all exposed components of the signs and support with primer and 2 coast of epoxy paints or powder coating as per clause 7.2 of IRC:67-2022) and erecting the sign board mounted over back support frame with vertical and lateral clearance as per clause 802.2 and 802.3 and relevant clauses and installed over a designed support system as per clause 802.6 of aluminum alloy or galvanized steel trestles and trusses of sections and typer as per structural design requirements and approved plans (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detaild in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board. (A) Truss and Vertical Support of aluminium alloy or galvanized steel

Add Extra, if circular/polygonal aluminium alloy/galvanise steel post is used instead of built-up section of angle/chanel/flat etc. for the vertical support of the truss and sign board (only the weight of posts shall be taken for this additional rate). (A) Truss and Vertical Support

Class-C Microprizmatic Grade sheeting of Type XI, fixed over 2mm thick Aluminium sheet as detailed above, for over head sign

Painting on Concrete Surfaces Two coats on new surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

(ii) Ordinary Kilometer Stone (precast)

(iii) Hectometer Stone (precast)

Providing and laying Reinforced Cement Concrete pipe NP 3 / prestressed concrete pipe on first class bedding. Laying Reinforced cement concrete pipe NP3 /prestressed concrete pipe complying IS:458 ends casted as per the requirments of flush jointing of pipe for culverts on first class bedding of granular material including joints duely filled and finished with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets. (B) 600 mm dia

Providing and laying Reinforced Cement Concrete pipe NP 3 / prestressed concrete pipe. Laying Reinforced cement concrete pipe NP3 /prestressed concrete pipe complying IS:458 ends casted as per the requirments of flush jointing of pipe for culverts including joints duely filled and finished with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets. (D) 1000 mm dia

Plain cement concrete complete as per drawing and Technical Specifications PCC Grade M 15

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with including all leads and lifts and as per relevant clauses of section-200 in (i) Lime / Cement Concrete (B) Cement Concrete Grade M-15 & M-20

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.) as per clause 304 (I) Ordinary soil (i) Upto 3M depth

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications as per clause 1500, 1700 & 2100 (A) Using batch type concrete mixer with integrated weigher. (i) P.C.C. Grade M-15

(A) Using batch type concrete mixer with integrated weigher. (ii) P.C.C. Grade M-20

Providing and laying Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications section 1500, 1700 and 2200 (A) Height upto 5m (a) Using batch type concrete mixer with integrated weigher. (ii) P.C.C. Grade M-20

Providing and laying Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications section 1500, 1700 and 2200 (D) Height upto 5m (a) Using batch type concrete mixer with integrated weigher. (i) R.C.C. Grade M-20

meter

Furnishing and placing Reinforced/ prestressed cement concrete in super structure as per drawing and technical specification section 1500, 1600 and 1700 (A) RCC Grade M25 (I) For Solid Slab Super Structure (a) Using batch type concrete mixer with integrated weigher (i) Height upto 5m

Filler joint (B) Providing and fixing 20mm thick compressible fibre board (12 m long x 25 cm deep) in expansion joint complete as per drawing specification

UOM Name

Percentage

Per mile

Siemens Per meter

Activity unit