REPAIR REPLACEMENT OF JOINERY ROLLING SHUTTERS OF ARMY AD CENTRE INCLUDING REPAIR REPALCEMENT OF ELECTRIC FITTINGS AND FIXTURES WIRING AT ARMY AD COLLEGE ADM REGT AND OTHER CONNECTED WKS AT GMS UNDER GE I GOS

Amount

Taking down rolling shutters of any size complete all as specified & directed.

Supply and fixing of steel rolling shutters as per IS-6248-1979, made of required size MS laths interlocked together through their entire length and jointed together at the ends by end locks mounted on shafts (50 mm dia) heavy duty, thickness of lathe 1.20mm, grade II springs, guide channel 3.15mm thick, bottom plate 3.15mm thick gear oprated shutter with bevel gear box and crank handle, hood cover 1.20mm and 1 coat of red oxide primer including necessary concrete bed blocks with PCC 1:3:6 of size wall width x 150mm x300 mm and finishing with plaster 15mm thick in CM 1:4 finished even and smooth complete all as specified & directed.

S&F ball bearing suitable for rolling shutter compete all as specifed & directed.

S&F safety lever locks with four levers for rolling shutters complete all as specified and directed.

S & F MS pipe 50 to 125 mm dia as shaft including two coats of aluminum paint over a coat red oxide primer complete all as specifed & directed.

Supply and fixing Gear Box Set general parts of steel rolling shutters complete all as specifed & directed.

All as per item No 6 above but Guide channel 3" (3.15 mm)

All as per item No 6 above but Bottom plate 5" (2.25 mm)

Greasing and servicing only to existing rolling shutters complete area of shutter n exc 20 Sqm each.

M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Taking down chowkats or frames not exc 1.5 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames exc 1.5 Sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description not exc 1.00 Sqm each complete all as specified and directed.

Taking down shutters of any description exc1.00 Sqm but not exc 2.00 Sqm each complete all as specified and directed.

M&L Second class hard wood (Sal) plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F mild steel flat iron as in bands straps, supports or stays for rainwater, ventilating pipes including bolt if required, hooks (stay) heavy for large gates,hook and pintle hinges,large hasps and staples, hold fasts, wall ties, hooks for hanging fans ,cleats for securing purlins to wood trusses or rafters and similar small articles conforming to Fe -290 Gde E-165 complete all as specified and directed.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate for fixing of hold fast and making good complete all as specifed & directed.

M&L Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.20 (a) complete all as specified and directed.

M&L Second class hard wood 35 mm thick factory made plain, framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings,frame work of watertanks and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed.

M&L butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type B-21 for 100 mm long complete all as specified and directed.

M&L butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised type C-21 for 75 mm long complete all as specified and directed.

S&F extruded aluminium alloy handles fabricated type anodised of 150 mm size complete all as specified and directed.

S&F extruded aluminium alloy handles fabricated type anodised of 100 mm size complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 100 mm long complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 150 mm complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 250 mm length of bolt complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 2nd class hardwood Beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc., and removing old beads to Store complete all as specifed & directed.

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

Takig down pelment boxes/cupboard shutters of any size and any type.

M&L Particle board 18/19 mm thick, medium density, flat pressed,single layer type or three layer type with BWR type adhesive, fixed with screws in pelmet boxes or in narrow widths n exc 15cm each rebated or flat edged complete all as specified and directed.

S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2010 Part-II complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed.

Taking down aluminium door and windows of any size and of any description built in wall and making good at disturbed surface with cement mortar 1:4 and applying two coats of plastic emulsion paint as per existing treatment complete all as specified & directed.

S&F anodised glazed side hung door shutters with anodised aluminium frame of section of 100x44x2mm and bottom rail of 44.5x99x1.8mm including 5.5mm thick tinted sheet glass ordinary quality with all necessary suitable push & pull plate/handle , screw, jointing cleats, rubber packing aluminium snap beading and 1 No 200mm long Aluminium tower bolt, 100mm long 3 No Aluminium butt hinges B-21 Type and one No mortice brass lock 100 size 4 leaver (Vertical Type) with 01 No door closer Aluminium (Diie cast) body hydraullically regulated designation ;No 02 universal type, for each shutters complete all as specifed & directed. (Door shall be size approx 1.2mx2.1 in single leaf)

S&F aluminium anodised galzed hung type window shutters made out from anodised aluminium frame of 'H' section size 34.00x43.5x2mm thick with 4mm tinted sheet galss (Weight not less than 0.57 kg/RM and shutter 'Z' of size 34.00x43.5x28.00mm having thickness 2.00mm (Wt not less than 0.50kg/RM) and all necessary jointing cleats , glazing, clips rubber packing, aluminium snap beading Tower bolt 100mm long 1 No and sliding hinges 180mm longs including aluminium grill with Mosquito proofing etc complete all as specified and directed.

M&L double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

S&F door closer hydraulically regulated designation No 1, universal type, suitable for door shutter of weight not more than 35 Kg of aluminium (extruded section body) complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone,concrete or brick surrounds, glazed with putty of fixed with beads complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F figured glass 3 mm thick, pin head type and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and apply one coat of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceilings and apply one coat of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceilings and applying one coat of oil bound distemper complete all as specified and directed.

M&L for rendering 15mm thick on other than fair face of brick works in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement and mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed. (Note: supply only of WPC shall be measured and paid for seperately )

Supply only integral water proofing compound all as specified and directed.

M/L for taking down carefully old UNSV aluminium point wiring with wooden batten /concealed and all accessories of(light, fan, socket or power) such as switches socket ceiling rose, fan regulators, light fitting, main switches DB’s etc and making good disturb surface all as specified and directed.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN Dbs/TPN DBs/ Main switch including old unserviceable MCCBs/ MCBs isolators etc and making good to disturbed surface all as specified and directed at site complete all as specifed & directed.

Taking down care fully copper/ aluminium sub main wiring of any size from surface / concealed / esisrting conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed.

M&L for point wiring in repairs with 1.5 Sqmm signle core PVC insulated unsheathed copper FRLS multi stranded conductor cable in and including concealed PVC conduit of size 20/25 MM ISI marked inclusive of tees, bend, elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminted 3mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sqmm FRLS cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal incuding cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by ENgr-in-Charge for following:-

All as per item No 55 Above but for One fan point controlled by one, one way switch.

All as per item No 55 Above but for One exhaust fan point controlled by one, one way switch.

All as per item No 55 Above but for One 5 Amp socket point controlled by one switch on independent board

All as per item No 55 Above but for One 5 Amp socket point controlled by one switch on same board

All as per item No 55 Above but for One light point controlled by two 02 ways switches 5Amp

All as per item No 55 above but with cable PVC insulated 4.0 Sq mm in and including PVC Conduit incl continuous earthing with cable PVC insulated 4.0 Sq mm copper conductor for power socket 15Amps.

M&L for point wiring in repairs with 1.5 Sqmm signle core PVC insulated unsheathed copper FRLS multi stranded conductor cable in and including PVC casing capping of size 20/25 MM ISI marked inclusive of tees, bend, elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminted 3mm thick sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sqmm FRLS cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal incuding cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-Charge for following:-

All as per item No 62 Above but for One fan point controlled by one, one way switch.

All as per item No 62 One exhaust fan point controlled by one, one way switch.

All as per item No 52 One 5 Amp socket point controlled by one switch on independent board

All as per item No 62 One 5 Amp socket point controlled by one switch on same board

All as per item No 62 One light point controlled by two 02 ways switches 5Amp

All as per item No 62 above but with cable PVC insulated 4.0 Sq mm in and including PVC Conduit incl continuous earthing with cable PVC insulated 4.0 Sq mm copper conductor for power socket 15Amps (Make : Anchor/ Standard/ Finolex/Havells)

M&L for point wiring with 1.5 Sqmm signle core PVC insulated unsheathed copper FRLS multi stranded conductor cable in and including concealed PVC conduit of size 20/25 MM ISI marked inclusive of tees, bend, elbows etc upto and including GI sunk boxes of size 1.2 mm thick and 60mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switch/ socket of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sqmm FRLS cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal incuding cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by ENgr-in-Charge for following:-

All as per item No 69 Above but for One fan point controlled by one, one way switch.

All as per item No 69 Above but for One exhaust fan point controlled by one, one way switch.

All as per item No 69 Above but for One 5 Amp socket point controlled by one switch on independent board

All as per item No 69 Above but for One 5 Amp socket point controlled by one switch on same board

All as per item No 69 Above but for One light point controlled by two 02 ways switches 5Amp

All as per item No 69 above but with cable PVC insulated 4.0 Sq mm in and including PVC Conduit incl continuous earthing with cable PVC insulated 4.0 Sq mm copper conductor for power socket 15Amps.

M&L for in repairs switch socket combination 2-in-1, 5 pin 5 Amp.

M&L for in repairs socket outlet 5 pin 5 Amp.

M&L for in repairs switch socket combination 2-in-1, 5 pin 5 and 15 Amp.

M&L for in repairs switch piano (Flush type) 5 amps, 240 Volts, single pole one way.

M&L for in repairs switch piano (Flush type) 5 amps, 240 Volts, single pole two way.

M&L for in repairs switch piano (flush type) 15 Amps , 240 volts, 50 Hz one way.

M&L for in repairs Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type complete.

M&L for in repairs stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed.

M&L for in repairs Bell push, flush type, 5 amp, 240 volts, 50 Hz complete.

Supply and fix in repairs modular socket 6A , 2/3 pin combined 2 module complete all as specified and directed.

Supply and fix in repairs modular switch6A complete all as specified and directed.

Supply and fix in repairs modular switch 1 way 16A, 1 module complete all as specified and directed.

Supply and fix modular socket 6A / 16A , 2/3 pin combined 2 module complete all as specified and directed.

Supply and fix in repairs modular 6A 1 module 2 way switch complete all as specified and directed.

S & F in repairs for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F in repairs for for Bell push modular 6 Amps single module complete all as specifed & directed.

Supply and fix Ceiling rose 3 termianl complete all as specified and directed.

Supply and fix Modular switch 2 way 6A, 1 module, 240 volts complete all as specified and directed.

S&F modular cover plate with frame for module 2 complete all as specified and as directed

S&F modular cover plate with frame for module 3 complete all as specified and as directed

All as per item No 95 above but for 4 module complete all as specifed and as directed.

All as per item No 95 above but for 6 module complete all as specifed and as directed

All as per item No 95 above but for 08 module complete all as specifed and as directed

All as per item No 95 above but for 12 module complete all as specifed and as directed

S&F Metal flush box 1/2 module complete all as specified and directed

S&F Metal flush box 3 module complete all as specified and directed

S&F Metal flush box 4 module complete all as specified and directed

S&F Metal flush box 6 module complete all as specified and directed

S&F Metal flush box 8 module complete all as specified and directed

S&F Metal flush box 12 module complete all as specified and directed

S&F Bakelite Sheet cover plate of size (5x5) complete all as specified and as directed

S&F Bakelite Sheet cover plate of size (8x5) complete all as specified and as directed

S&F Bakelite Sheet cover plate of size (11x13) complete all as specified and as directed

S& F In Replacement PVC Gang box Square type for fittings complete all as specified and directed

S& F In Replacement PVC Board box of (4x4) Size complete all as specified and directed.

S& F In Replacement PVC Board box of (6x8) Size complete all as specified and directed.

S& F In Replacement PVC Board box of (8x10) Size complete all as specified and directed.

M&L for in repairs Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and directed.

S & Fin repair LED light fitting 18/ 20 Watt T5 batten type,PVC extruded batten with decorative end caps complete with polycarbonate /glass tube 4Ft White , internally pre-wired and including connecting up with suitable twisted flexible copper conductor cable with suitable size complete all as specified & directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S & F in repair of light fittings (2Ft) with wall mounted LED pattern with polycarbonate housing & integrated electronic driver of 10W cap T5(max lenght upto 600mm) complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F in repair LED globe light decorative wall light fixture made up of polycarbonate, suitable for 9W LED bulb B22 base complete incl 9 watt bulb complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F in repair aesthetically designed, decorative recess mounted 3Watts (Round) 3000 K spot light for low ceiling height complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F in repair aesthetically designed, decorative recess mounted 5 Watts (Round) 3000 K spot light for low ceiling height complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F in repair aesthetically designed, decorative recess mounted 12 Watts (Round) 6500K spot light for low ceiling height complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F in repair aesthetically designed, decorative recess mounted 06 Watts (Round) 6000K spot light for low ceiling height complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F in repairs crysta chip on board (COB) swivel downlight with crisp light throw and high CRI with capacity 3Watts complete 220 volts all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F in repairs crysta chip on board (COB) swivel downlight with crisp light throw and high CRI with capacity 6 Watts complete 220 volts all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F in repairs LED recessed panels with inbuild occupancy sensorwith inbuilt capability of switching on/off basis the occupancy in any space and is perfect for general and office lighting with capacity 36 watts 2x2 ft complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S & F in repairs high efficiency 2x1 ft recess LED flat panel with high brightness LED for glare free homogenous illumnination with capacity 20 watts complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

Supply and fix in replacement of bldg security light fitting LED type of 25 watt New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 luminaire with high power LEDs as light source and electronic driver. mounting bracket suitable to house the light fittinhg , with its Galvanised Flat Iron clamps conntected nuts bolts etc complete all as specified & directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

Supply and fixing in repairs baybrite flare multi functional LED luminaire of capaity 120 watts complete all as specified and directed. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

M/L for replacement of 2 Runs of cable PVC insulated but unsheathed 4.0 Sq mm, stranded copper conductor in and including PVC conduit with continuous earthing cable PVC insulated 2.5 Sq mm, stranded copper conductor all as specified and directed.

M/L in replacement of 2 Runs of cable PVC insulated but unsheathed 1.5 Sq mm, stranded copper conductor in and including PVC conduit with continuous earthing cable PVC insulated 1.0 Sq mm, stranded copper conductor all as specified and directed. Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre.

M/L in replacement of 2 Runs of cable PVC insulated but unsheathed 2.5 Sq mm, stranded copper conductor in and including PVC conduit with continuous earthing cable PVC insulated 1.5 Sq mm, stranded copper conductor all as specified and directed. Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre.

M/L replacement of 2 Runs of cable PVC insulated but unsheathed 6.0 Sq mm, stranded copper conductor in and including PVC conduit with continuous earthing cable PVC insulated 4.0 Sq mm, stranded copper conductor all as specified and directed.(Cable make Anchor/Havells/Finolex) Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre.

M/Lreplacement of 2 Runs of cable PVC insulated but unsheathed 10 Sq mm, stranded copper conductor in and including PVC conduit with continuous earthing cable PVC insulated 6.0 Sq mm, stranded copper conductor all as specified and directed. (Cable make Anchor/Havells/Finolex) Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre.

S& F In Replacement 3 core 1 Sqmm round Sheathed copper wire complete all as specified and directed

S & Fix in replacement sheet metal enclosure vertical DBs with provision for FP MCCB frame upto 100A in 16,KA as incomer 4 way double door made all as specified and directed.

S & Fix replacement sheet metal enclosure double door MCB DB, 220 volts, SPN 12 way complete all as specified and directed.

S & Fix replacement sheet metal enclosure double door MCB DB 220 Volts, SPN 8 way complete all as specified and directed.

S & Fix replacement sheet metal enclosure double door MCB DB 220 volts , TPN 4 way complete all as specified and directed.

S & Fix replacement sheet metal enclosure double door MCB DB 415 Volts, TPN 8 way complete all as specified and directed.

S & Fix replacement sheet metal enclosure double door MCB DB 415 Volts, TPN 12 way complete all as specified and directed.

Supply and fixing in repairs 5-32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) Single pole to be fixed in DB complete with connection testing and commissioning.

Supply and fixing in repairs 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) Single pole neutral to be fixed in DB complete with connection testing and commissioning.

Supply and fixing in repairs 40-63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) Single pole neutral to be fixed in DB complete with connection testing and commissioning.

Supply and fix in repairs MCCB 4 Pole, 415 V, fixed type, 25 to 100 Amps with breaking capacity 16 KA complete all as specified and directed

Supply and fix in repairs MCCB 4 Pole, 415 V, Adjustable type, 160 Amps with breaking capacity 36 KA complete all as specified and directed

Supply and fixing in repairs 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN 16 to 32 Amps current carrying capacity in the DB complete with connection testing and commissioning.

Supply and fixing in repairs 415V 10KA 'C' curve miniature circuit breaker (MCB) TPN TPN 40 To 100 AMPs current carrying capacity in the DB complete with connection testing and commissioning.

S&F in replcment of single pole and neutral enclosure with a two pin and earth plug socket 240 V with one MCB SP ‘C’ series rating 20 to 30 Amp complete all as specified and directed.

M&L, replacement for earthing with galvanized steel earth plate electrode 600 x 600 x 6mm thick, buried directly in ground(earth pit not less than 2.25 mtrs deep below ground level)with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers protected with & including 15 mm dia light grade GI pipe necessary excavation and earth works, charcoal and common salt filling, watering arrangement with 20 mm GI pipe light grade including PCC pit with Pre cast RCC (1:2:4) cover, GI funnel with mesh test point, testing & commissioning complete all as specified and directed.

Supply testing and commissioning AC three phase ,3x 240V ,50Hz, digital,electronic tamper proof energy meter of rating 10 to 60 Amps covered with PVC transparent cover with optical communication port incl taking down the unsv meter complete all as specified and directed.

Supply testing and commissioning AC single phase,50Hz, digital,electronic tamper proof energy meter of rating 5 to 30 Amps covered with PVC transparent cover with optical communication port incl taking down the unsv meter complete all as specified and directed.

S&F in repairs of LED bulbs in globe lights/fancy lights by replacing 7/9 watts LED bulbs in place of CFL bulb complete all as specified and directed

S&F in repair of PVC casing/ caping of size 25MM with ISI mark, by removing the old broken one complete all as specified and directed

S&F in repairs aestheticlly designed 1x1 ft LED flat panel for surace/recess mounting of capacity 24 watts complete all as specified and directed

S&F in repairs male/female sockets 5A, 220 volts, 50 Hz complete all as specified and directed

S&F in repair modular mcb sp 6 to 32 Amps, 220 volts, 50 Hz complete all as specified and directed

S&F LED strip lights with high brightness IP65 with unifomiy of lights complete all as specified and directed

S & F for PVC non-metallic rigid conduit ISI marked heavy duty white/ Ivory colour and its accessories heavy duty ISI marked of size 20 mm dia for LAN, telephone and TV connections including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed.

M&L for removing the exisitng panel and depositing it to AGE E/M office for safe custody and refixing the same after completion of work complete all as specified and directed

M/s MAA BHAIRABI ENTERPRISES

HARAGOURI SUPPLIERS

R K Traders

ABC CONSTRUCTION COMPANY

V.Venkata Ramaiah

M/s Bapujee Builders and Traders