Loading
Loading…
Loading…
Tender Value
₹82.2 L
EMD Value
₹1.6 L
Closing Date
27 Jul 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
TRACK2
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-XIVA, of STD/Jan/26 along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work each costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Any P-Way works.
34 conditions · 8 needing a document upload
Check list should be as per the annexure-XXIII as given in the tender document attached. Note: Tenderer's attention is invited to clause 1 of Section VII and other relevant clauses of Section I and II whereby in case of nonsubmission/ non compliance, the tender offer is likely to be rejected.
1.1) Following documents are common for all types of firms i.e. Sole proprietorship, Partnership, Limited Company or JV.
(a)Tender Form (First Sheet) as per 'Annexure-I' (Mandatory)
(b) Firm details as per Annexure-II
(c)Format for Certificate as per proforma given in 'Annexure-III A' (Mandatory)
(d) List of works of similar nature physically completed in all respects in current and last three financial year as per proforma given in 'Annexure-IV'
(e)Work Completion Certificate of works mentioned in para (d) above from the Organizations with whom they worked as per proforma given in 'Annexure-V' as applicable. (Mandatory)
(f)List of works on hand as per proforma given in Annexure-VI
(g)List of plants & Machinery available on hand (own) and proposed to be inducted (own and hired to be given separately) for the subject work in Annexure-VII.
(h)List of Personnel, Organization available on hand and proposed to be engaged for the subject work in Annexure -VIII.
(i) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-XIVA, of Standard Tender Document along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(j)Self attested copy of Permanent Account Number (PAN) issued by Income Tax Department.
(k)The tenderer(s) are required to submit the test report of the stone ballast conforming to railways specifications as given in the condition no.7.2.2 of section-VI along with their offer, issued from the approved laboratory as listed in condition no 7.1.1(a) of section-VI in the tender documents. (This item will be applicable only for the tenders of supply of ballast).
(l)Any other document in support of his/their credentials/scheme.
(m)Contractual Receipt of the year on the Letter Head of Chartered /Cost accountant. 'Annexure-IX' (Mandatory)
1.2 In addition to Para 1.1 above certain more documents are to be submitted by tenderers as per status of their firms. These documents are listed below - (Mandatory)
1.2.1For Sole Proprietorship firm a)Affidavit as per 'Annexure - X'. b)Special power of Attorney as per proforma given in 'Annexure-XI' to be submitted by sole proprietor firm duly notarized.(Not required if tender documents are submitted by proprietor himself) (Mandatory)
1.2.2 For Partnership firm a)Self/Notary attested copies of Partnership deed. b)Special Power of Attorney as per proforma given in 'Annexure-XII' to be submitted by Partnership firm. (Not required if one or more partners are authorized in Parternership deed to sign on behalf of the firm.) (d)All other documents in terms of explanatory notes in clause 22 of Standard Tender Document.
1.2.3 For Limited Company a) Copy of Memorandum & Articles of Association of Company. b)Self /Notary attested copy of resolution passed by Board of Directors authorizing its Director/Employee to deal with tender on behalf of company. c) 15.1.1 Attested copy of Notarized Special Power of Attorney including ratification clause duly signed by person authorized by the company vide (b) above as per proforma given in 'Annexure- XIII'. d) A copy of Certificate of Incorporation (Mandatory)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
NOTE: BE IT KNOWN TO THE TENDERER THAT :-
All mandatory documents are required to be submitted by the bidder/tenderer at the time of bidding, in case of nonsubmission/ noncompliance, the tender offer is likely to be rejected.
(a)No post tender submission of documents shall be permitted in respect of item mentioned above. However, only clarification can be called for by Railway in respect of any part / document submitted by the tenderer which shall be responded to by the tenderer within 10 working days of the date of issue of such letter for clarifications, failing which the offer shall be dealt with as per available documents.
Yard Remodeling work at NBQ Yard (Phase-I). (Project Id-08.04.31.25.3.53.009)
33-ENGG-RNY-2026-27
33-ENGG-RNY-2026-27
Open
Works - General
6 Months
Kamrup, Assam
₹0
₹1.6 L
27 Jul 2026
6 Jul 2026
13 Jul 2026
62 items across 1 schedule · ₹93,73,533.63 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | For Casual/Scattered Rail Renewal work | RM | 632.00 | 39.91 | 25,223.12 |
| 2 | For Casual/Scattered Rail Renewal work | RM | 182.00 | 42.26 | 7,691.32 |
| 3 | For location of work not involving deep screening | Each | 500.00 | 383.45 | 1,91,725 |
| 4 | Rail section of 90R and below | Each | 100.00 | 119.15 | 11,915 |
| 5 | Rail section of 52Kg and above | Each | 100.00 | 142.98 | 14,298 |
| 6 | 1 in 8½ Turnout (Under Traffic Block) | Set | 7.00 | 35,654.56 | 2,49,581.92 |
| 7 | 1 in 12 Turnout (Under Traffic Block) | Set | 2.00 | 40,799.74 | 81,599.48 |
| 8 | 1 in 8½ Turnout | Set | 3.00 | 44,480.1 | 1,33,440.3 |
| 9 | 1 in 12 Turnout | Set | 6.00 | 49,948.25 | 2,99,689.5 |
| 10 | 1 in 8½ Turnouts | Set | 3.00 | 51,137.17 | 1,53,411.51 |
| 11 | 1 in 12 Turnouts | Set | 6.00 | 59,305.9 | 3,55,835.4 |
| 12 | For 1 in 8½ Points & Crossing | Set | 3.00 | 8,837.08 | 26,511.24 |
| 13 | For 1 in 12 Points & Crossing | Set | 6.00 | 11,169.1 | 67,014.6 |
| 14 | Sleepers up to 2.85 m length | Each | 50.00 | 684.36 | 34,218 |
| 15 | Sleepers of length more than 2.85 m and up to 4.20 m | Each | 196.00 | 943.47 | 1,84,920.12 |
| 16 | Sleepers of more than 4.20 m length | Each | 50.00 | 1,487.83 | 74,391.5 |
| 17 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 1500.00 | 29.56 | 44,340 |
| 18 | Under Traffic Block Conditions: | cum | 1950.00 | 59.02 | 1,15,089 |
| 19 | When distance of nearest quarry is up to 10 km | cum | 1050.00 | 2,429.01 | 25,50,460.5 |
| 20 | For 60 Kg/60EI-R260 grade Rail, Single shot crucible fitted with Automatic Tapping Thimble Technology, 3 pieces Mould (Zircon washed) and Compressed Air Petrol heating technique. | Each | 80.00 | 2,078.4 | 1,66,272 |
| 21 | Spreading of ballast, from existing stacks available along formation on top or at cess, in required uniform thickness, compaction of ballast layer laid on new formation at all the locations with smooth wheeled power roller of 8- 10 tonne capacity to sufficient number of passes to form consolidated ballast bed of approximately 250mm thickness to a width of 4m symmetrical to centre line of proposed track in correct line & level with all ascents & descents, as directed by Engineer in-charge. Note: Item is inclusive of (a) providing ramp for taking roller to formation and removing the same & making good formation after completion of work; (b) redistribution & leveling of excess ballast while rolling to obtain uniform plane cambered surface. | cum | 1050.00 | 44.5 | 46,725 |
| 22 | Maximum Shifting / Slewing up to 1 metre | TRM | 1800.00 | 232.36 | 4,18,248 |
| 23 | For PSC Sleeper Track with Sleeper Density of 1660 | TRM | 8500.00 | 154.78 | 13,15,630 |
| 24 | For PSC Sleeper Track with Sleeper Density of 1660 | TRM | 4500.00 | 119.06 | 5,35,770 |
| 25 | 1 in 8½ PSC layout | Set | 3.00 | 12,850.89 | 38,552.67 |
| 26 | 1 in 12 PSC layout | Set | 6.00 | 16,744.29 | 1,00,465.74 |
| 27 | For rails up to 13 metre length | TRM | 300.00 | 40.55 | 12,165 |
| 28 | For Rail panel more than 40m length | RM | 400.00 | 28.22 | 11,288 |
| 29 | Other than PSC Sleeper track - Maximum slew up to 50mm | TRM | 1500.00 | 119.49 | 1,79,235 |
| 30 | With Contractor's Hydraulic Rail tensor | TRM | 1500.00 | 57.03 | 85,545 |
| 31 | With 2 bolts | Set | 80.00 | 123.26 | 9,860.8 |
| 32 | With 4 bolts | Set | 60.00 | 136.3 | 8,178 |
| 33 | With Contractor's hard wood block. | Each | 20.00 | 2,828.77 | 56,575.4 |
| 34 | Drilling holes of 16mm to 22mm dia. on all types of PSC sleepers and fixing the dowels with adhesive of RDSO approved quality for fixing check rails & guard rails, as directed by Engineer in-charge. | Each | 150.00 | 401.9 | 60,285 |
| 35 | Cleaning of side drains along the track including disposing of muck beyond Railway boundary as per instructions of Engineer in-charge to keep drains clean and clear in cuttings etc. | RM | 400.00 | 36.37 | 14,548 |
| 36 | Removing weeds & bushes in ballast section and cess up to 3.95m from centre line of track in mid section & station yard, as specified by Engineer in-charge including disposal of branches, bushes outside cess/yard. | TRM | 21300.00 | 16.74 | 3,56,562 |
| 37 | Making kutcha trapezoidal side drain of bottom width as 300mm and depth of 450mm in cutting section by excavation in all types of soil including utilising excavated muck for dressing of cess, slopes etc. in Railway land. | RM | 400.00 | 143.32 | 57,328 |
| 38 | For 60 Kg Rails | RM | 2500.00 | 78.99 | 1,97,475 |
| 39 | Anti-corrosive painting to weld collar for Thermit welded rail joints on track or on cess for new welded joints to protect against normal corrosion for any rail section with two coats of ready mixed bituminous black paint of reputed make confirming to latest IS:9862 on welded area up to 10cm on either side including on the underside of rail foot by brush including surface preparation as per Railway's AT Weld Manual including lettering / weld numbering with approved enamel paint as directed Note: Before painting, dust, loose rust and mill scale and dirt shall be removed thoroughly by wire brushing. Scrubbing welded area with water to make it free from slag and other water soluble compounds to make it dry. | Each | 80.00 | 26.78 | 2,142.4 |
| 40 | Kilometre & Gradient post | Each | 80.00 | 103.89 | 8,311.2 |
| 41 | Hectometre Post | Each | 80.00 | 121 | 9,680 |
| 42 | Curve Post | Each | 160.00 | 111.11 | 17,777.6 |
| 43 | CSM / DUO / 3X with or without DGS (7.5 KVA generator and 8x500 W) | Night | 60.00 | 5,431.83 | 3,25,909.8 |
| 44 | 60 Kg - 110/90 UTS - On Running Line | Each | 200.00 | 412.7 | 82,540 |
| 45 | 52 Kg - 90 UTS- On Running Line | Each | 100.00 | 334.53 | 33,453 |
| 46 | On Running Line | Each | 200.00 | 81.15 | 16,230 |
| 47 | For lead up to 500 metre. | MT | 170.00 | 430.9 | 73,253 |
| 48 | During period of traffic block | MT | 29.00 | 32.84 | 952.36 |
| 49 | Lead beyond 20 Km and up to 30 km | MT | 24.00 | 367.37 | 8,816.88 |
| 50 | Lead beyond 50 Km and up to 100 Km | MT | 24.00 | 697.45 | 16,738.8 |
| 51 | Lead beyond 50 Km and up to 100 Km | MT | 100.00 | 567.89 | 56,789 |
| 52 | Lead beyond 100 Km and up to 150 Km | MT | 96.00 | 906.53 | 87,026.88 |
| 53 | Extra for every Km per MT beyond 150 Km over item no. 172057 | MT-Km | 5760.00 | 3.46 | 19,929.6 |
| 54 | From Truck / Trailer | MT | 67.00 | 120.97 | 8,104.99 |
| 55 | P.Way fittings of all types and other similar loose items | MT | 60.00 | 435.2 | 26,112 |
| 56 | Painting of running rails and check rails of any rail section of level crossing with anti-corrosive paint on both sides of web, foot etc. including liner contact area (excluding bottom of foot) and fishing plane with two coats of thickness of 100 microns each by bituminous black paint confirms to IS-9862 of reputed make including painting of liners, ERC surface preparation, i.e. cleaning with wire brush / sand paper as a complete job as per Para No 613 (2)(b)(iii) of Indian Railways Permanent Way Manual, as directed by Engineer in-Charge. | RM | 800.00 | 63.38 | 50,704 |
| 57 | Fabricating of check rails of 52Kg and 90R sections for providing to curves by cutting web of rail horizontally by gas, grinding for smoothening the cut edge and drilling of parabolic shaped holes to the web of check rails as per drawing and specification and as per directions of engineer in-charge with all contractor's labour, tools and materials complete. Note: 1. Rails shall be supplied by Railways 2.The both ends of head of check rails are to bent/cut as per drawing. 3. The released rail scrap shall be stacked neatly with in a lead of 500m. 4.Drilling of holes shall be paid under relevant item. | RM | 200.00 | 241.6 | 48,320 |
| 58 | Dismantling Check Rail on curves on track of all rail sections, duly removing fish plates and bolts including removing chairs from sleepers, leading and stacking released materials away from track clear of infringements, complete and as directed. | RM | 200.00 | 70.98 | 14,196 |
| 59 | Fixing of check rails on curves on track of all rail sections as per drawing and to correct alignment and level with Railways fastenings including leading of rails and fittings, crossing of tracks, greasing of plate screws with approved grease etc., as per drawing and directions of Engineer in charge with all contractors labour, tools, plants, machinery, consumables etc., complete. Note: Required P.Way fittings will be supplied at SSE/P.Way stores. | RM | 200.00 | 81.21 | 16,242 |
| 60 | JCB Backhoe Loaders 3DX Plus or similar with minimum 1.10 cum bucket capacity | Hour | 40.00 | 827.84 | 33,113.6 |
| 61 | Hydra or similar tyre mounted Pick-n-Carry crane of 12T capacity for misc. works of handling of material | Hour | 60.00 | 1,536.98 | 92,218.8 |
| 62 | Tractor with Trolley for local transportation or other misc. works. | Hour | 90.00 | 365.64 | 32,907.6 |
| Schedule total | ₹93,73,533.63 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TD_33-ENGG-RNY-2026-27.pdf
ATTACHMENT
2026_03_13AdvanceCorrectionSlipNo_11.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .