SPECIAL REPAIRS TO BLDG NO. T-184 AND T-182 OF FD HOSP AND SPECIAL REPAIRS TO BLDG NO. T-35, T-232 (OR LIVING) AND T-238 OF IBSC AT ALONG MIL STNS UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Cement Concrete (Reinforced) in any Position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry Walling, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantling 40 Sq Cm and Over in Section in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed.

Taking down Wooden Chowkat or Frame of any description (without Taking Off Shutter from the Frame), exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Taking down Aluminium Door/ Window Frame with Shutter (without Taking Off Shutter from the Frame), not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Taking down/out Unserviceable Worn out Wire Cloth/Netting of any description, fixed with Beads, etc., complete all as specified and as directed.

Hacking out Old Broken Glass (any thickness, size, quality or description) from Wooden or Metal Frame or Stone, Concrete or Brick surrounds including hacking out old Putty or removing Beads, etc., punching or drilling out old Glazing Pins/ Spring Clips, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work of any description not otherwise provided for, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating the Serviceable Plain or Corrugated Steel Sheeting and Stacking properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Ceiling Frame (Snap Grid) with Hangers of any descriptions but except Wall and Ceiling Boards, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, scrubbing down with Water and Removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to include in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under Reamed Piles, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Roof Beams, Lintel Bands, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Chajjas, Chullah Hoods, Troughs and Similar Items, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns and Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Works; not exc. 200mm thick (Horizontal or Sloping), etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Chullah Hoods, Chajjas, Trough and and Similar Items including Edges (Horizontal or Sloping) Rough Finished Surface of Concrete Flat, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), 10 Cm in Width and Setting in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Holes in Brick/ Pre-cast Concrete Block Walling, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to Dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Boarding 50mm thick (100x50mm) in Frame Work to Ceiling, etc., Planned on One Side, fixed in any Position with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Cleanswan, Square, Rectangular or Triangular in Section, exc. 13.00 Sq Cm but not exc. 25.00 Sq Cm (50x50mm as STUDS), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Cleanswan, Square, Rectangular or Triangular in Section, exc. 6.00 Sq Cm but not exc. 13.00 Sq Cm (25x25mm as FORKING PIECE), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain Fillets, Wrought, Square, Rectangular or Triangular in Section, exc. 3.00 Sq Cm but not exc. 6.00 Sq Cm (40x12mm as COVER FILLET), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick BWP, Commercial Ply or 12mm thick Veneered Particle Board Medium density, Wood Particle Board with Commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

S&F Second Class Hardwood (well seasoned) Small Fittings such as Brackets of any type, Latch and Hinge Blocks, Shaped Door and Window Stops and the like, including all necessary Labours; Articles not exc. 200 Cu Cm Each, complete all as specified and as directed. NOTE : Butt Hinge (if required/ordered) will be Measured and Paid under appropriate Item as 'Supply only'.

M&L Anodised Aluminium Frame for Doors, Windows, Ventilators with One or More Rebates including Joining Cleat for fixing, etc., complete all as specified and as directed.

M&L Anodised Aluminium Door Shutters, Aluminium Section weighing not less than 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber/ Neoprene Packing, Handles (as approved) - 2 No. in Each Door, Stainless Steel Hinges of Size as ordered, anodised Aluminium Snap Beading, Screws, etc., complete all as specified and as directed. NOTE : Cost of Aluminium Fittings/ Builders Hardware as metioned here-in-above will deem to include in the Quoted Unit Rate.

M&L Anodised Aluminium Window and Ventilator Shutters, Side Hung type without Sash Bars, Aluminium Sections weighing 0.55 KG/RM including necessary Joining Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, Screws, Anodised Aluminium Fittings such as Peg Stays 150mm long (1 No.). Hinges Type B-21, 100mm long (2 No.) suitable Handle (1 No.), complete all as specified and as directed. NOTE : Cost of Aluminium Fittings/ Builders Hardware as metioned here-in-above will deem to include in the Quoted Unit Rate.

S&F Anodised Aluminium Grill for Window and Ventilator, etc. of Size as per Site requirement (as approved), complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt, 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy, complete all as specified and as directed.

Supply only Stainless Steel Butt Hinge 50mm in size, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge 100mm in size, complete all as specified and as directed.

S&F Aluminium Handle 150mm, Cast type, anodised, complete all as specified and as directed.

S&F Floor Door Stopper having Overall length of Cover Plate 140mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Floor Door Stopper having Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Brass Mortice Lock, Vertical type of size 100mm, 4 Levers (as approved), complete all as specified and as directed.

S&F Door Closer Aluminium alloy (Extruded Section) Body, Hydraulically Regulated, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in Width and of Weight between 61.00 to 80.00 KG and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Sheet Glass 5.5mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square, not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Solar Control Film 25 Micron, Reflective type, Sticked to Glass Panes as per Instructions of Manufacturers, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts (Flat Iron 25x3.0mm thick); Wall Ties and similar Small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Rolled Mild Steel in Joist, Channel, Angle, or Tee Sections in Vertical Post, conforming to Fe-410-W (Gde E-250) Quality 'B', fixed independently, without Connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the Length indicated), complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or Other Connecting Plates, complete all as specified and as directed.

M&L Mild Steel Tublar Trusses, Rafter, Purlins, etc. including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:1161-1979, Grade St-240, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or Notched (Ordinary and Counter Sunk) forming Holes, without any Aattachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Running Welding in Repairs in Steel Works, thickness of metal to be welded not exc. 6.0mm, complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @ 120 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Re-fixing Corrugated Mild Steel Sheeting of any thickness (except Sheets, Serviceable Sheet obtained from BOQ Item No. 1.011 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.80mm thick, Galvanised @ 120 Gram Per Sqm, in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Re-fixing Plain Mild Steel Sheeting of any thickness (except Sheets, Serviceable Sheet obtained from BOQ Item No. 1.011 here-in-before) in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted (Green Colour) Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Refixing Pre-painted Galvalume Corrugated Steel Sheet (Serviceable Pre-painted Galvalume Corrugated Steel Sheet obtained from BOQ Item No. 1.011 here-in-before) in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted (Green Colour) Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Anodised Aluminum Snap Grid/ Frame Work of size 605x605mm, all as per Specification and Drawing of MES Schedule (but except Hangers), complete all as specified and as directed.

S&F Hangers 6.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F Plywood Board 6.0mm thick, Grade BWP, Type BB, fixing with Mild Steel Screws to Timber/ Aluminum Frame Work as in Ceiling, Flat or Sloping, etc., complete all as specified and as directed.

S&F Plywood Board 6.0mm thick, Grade BWP, Type BB, fixing with Mild Steel Screws to Timber Frame Work as in Wall Panelling, etc., complete all as specified and as directed.

S&F Perforated Particle Board/ Tiles 12mm thick, 600x600mm in Size for Insulation and Accoustic purposes, fixed with Nails to Timber Frame Work or with Staples on Snap Grid, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smooth with using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strips 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality as approved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deem to include in the Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rect-angular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deem to include in the Quoted Unit Rate.

M&L Virified Ceramic Tiles 10mm thick (Square/ Rectangular) Polished, Area of Each Tiles not exc. 0.36 Sqm (1st quality as approved) in Floors etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deem to include in the Quoted Unit Rate.

M&L Virified Ceramic Tiles 10mm thick (Square/ Rectangular) Polished, Area of Each Tiles not exc. 0.36 Sqm (1st quality as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deem to include in the Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth Without Using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick on Brick/PCC Blocks or Concrete Works in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/ Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid separately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Wall Care Putty 3.0mm thick in Two Coats (1.5mm thick in Each Coat) on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain an Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and Applying Two Coats of Cement Based Paint (as approved Tint) over a Coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Complete Removal of Existing Surface Treatment of Walls and Applying Two Coats of Cement Based Paint (as approved Tint) over a Coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and Applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and Applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and Applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and Applying Two Coats of Synthetic Enamel Paint (1st quality Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New Steel and Iron Surfaces of any descriptions, over 10 Cm in Width or Girth and Applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any descriptions, over 10 Cm in Width or Girth and Applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Old Painted Steel and Iron Surfaces of any descriptions (on Corrugated Sheets), over 10 Cm in Width or Girth and Applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New Steel and Iron Surfaces of any descriptions, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and Applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors including Taking up or down Steel Tubing 15mm bore (dia) and Connections, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors including Taking up or down Steel Tubing 20mm bore (dia) and Connections, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butter-fly handle, screwed down, screwed for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with Long Screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, with Long Shank and Cup (Concealed type), screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Valve 20mm bore (dia), Cast Copper alloy, Chromium plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated (as approved), screwed down, high pressure, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule, Providing Water Pipe Line Connections including Lowering down unserviceable Water Storage Tank of any description after disconning of Water Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Gram, high pressure with Epoxy Coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of Size 580x440mm, Orissa Pattern with Integral Foot Rest, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzle of WC Pan) including Provision of Lime Concrete Bedding and Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float & Handle, Flush Pipe of Polyetylene of Low or High Density or PVC Pipe 32mm bore (dia) of suitable Length, a Pair of Cast Iron Brackets/ Erecting Stand duly Painted including Cutting and Pinning in Ends, Making Good disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 550x400mm in Size, Flat Back with Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) of suitable Length, a Pair of Cast Iron Bracket/ Erecting Stand duly Painted, Cutting and Pinning in Ends and Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in Size and 450mm in length with PTMT Nuts suitable for connecting with Flushing Cistern, Wash Hand Basin, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F Brass Chromium plated Shower Rose 125mm in Size with Arm and Flanges, with or without Swivel Joints including fixing to GI/ Steel Pipe 15mm bore (dia) or Union, complete all as specified and as directed.

S&F Stainless Steel Soap Dish of Approved Pattern, Size not less than 150mm, fixed on Wall with Wooden Plugs and Brass Chromoum Plated Screws and Fixed-in-repairs, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixed on Wall with Wooden Plugs and Brass Chromoum Plated Screws and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Floor Trap having Diameter of Outlet 75mm, Plain with Grating including Jointing to Waste Pipe fixed with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any Length with Rubber Ring Joints, laid in Floors or Fixed to Walls, etc. including Taking up or down Pipe of any descriptions, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any Radius, etc. and Jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down Unserviceable Sub-main Wiring from PVC Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 6 AMP 3 PIN SOCKET OUTLET POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 6 AMP, 3/5 PIN SOCKET POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 2.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 6/16 AMP, 3/5 PIN SOCKET OUTLET POINT on INDEPENDENT BOARD, complete all as specified and all as directed.

M&L Point Wiring with 4.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 4.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 16 AMP, 3 PIN SOCKET OUTLET POINT on INDEPENDENT BOARD, complete all as specified and all as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable and 1-Run of 6.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping will deem to include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Casing Capping only. Wires required for Looping, etc. as ordered will deem to include in the Quoted Unit Rate.

S&F PVC Casing Capping (ISI Marked) of size 25mm including all Fitting/ Fixtures such as Tee, Bend, Elbow, Socket, Saddles, etc. including Taking down/ out Unserviceable PVC Casing Capping, complete all as specified and as directed.

S&F Rigid Non-metallic PVC Conduit of Size 20mm (External Dia), exclusive of Boxes (Junction/ Terminal) but inclusive of all Tees, Bends, Elbows, Reducers, Bell Mouth Tube Ends and Fixing Accessories such as Couplers, Lock Nuts, Saddles, Pipe Hooks, etc. including Taking down/out Unserviceable PVC Conduit Pipe, complete all as specified and as directed.

S&F PVC Rectangular Closed Recessed Board/Block of Size 350x300x50mm Deep with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down/out Unserviceable Board/ Block of any description, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, 1-way, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 5 Pin, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 3/5 Pin 6 Amp & 3/5 Pin 16 Amp, 2-in-1 (Multi-plug), 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination, Multi-purpose type, 2-in-1, (3 Pin & 3 Pin) 6/16 Amp, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Rose Surface type, Bakelite 65x50mm, 3 Terminals suitable for 230 Volt AC, 6 Amp and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Stepped type, Electronic, Flush type, 120/280 Volt and connecting up, complete all as specified and as directed.

S&F Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F LED Bulk Head Light Fitting 10 Watt, Enviroment Friendly, Ultra Modern, Energy Saving, Surface Mounted comprising of High Brightness LEDs, Electri-cally connecting up with and including Twisted Flexible Copper Conductor Cable of Size 40/0.0076, Twin Core of suitable Length including Taking down/ out Unserviceable Light Fitting, complete all as specified and as directed.

S&F LED Tube Light Fitting 1x20 Watt, T-05 with 20 Watt LED Tube Rod and Integrated Electronic Driver, LED Batten with Aluminium Extrution Housing, Basic all Purpose, Surface and Wall mounted, complete with all Accessories, Pre-wired, fixing on 2 No. PVC Boxes, Electrically connecting up with and including Twisted Flexible Copper Conductor Cable of Size 40/0.0076, Twin Core of suitable Length including Taking down/ out Unserviceable Light Fitting, complete all as specified and as directed.

S&F LED Tube Light Fitting 1x20 Watt, T-08 with 20 Watt LED Tube Rod and Integrated Electronic Driver, LED Batten with Aluminium Extrution Housing, Basic all Purpose, Surface and Wall mounted, complete with all Accessories, Pre-wired, fixing on 2 No. PVC Boxes, Electrically connecting up with and including Twisted Flexible Copper Conductor Cable of Size 40/0.0076, Twin Core of suitable Length including Taking down/ out Unserviceable Light Fitting, complete all as specified and as directed.

S&F LED PANEL (2'x2') Light Fitting 28-32 Watt with High Brightness SMD LEDs as Light Source, Recess/Ceiling mounted, Ultra Modern, Enviromentaly Friendly, New Generation with Electronic Driver 28-30 Watt, complete with all Accessories, Pre-wired, Electrically connecting up with including suitable Size and Length Twisted Flexible Copper Conductor Cable, 3 Core including Taking down/ out Unserviceable Light Fitting, complete all as specified and as directed.

M&L Taking down Ceiling Fan/ Exhaust Fan of any Make/Model/Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-hanging/ Re-fixing, complete all as specified and as directed.

M&L Transporting Ceiling Fan 1200mm Sweep from the Site of Work at ALONG to nearest Workshop, Removing burnt Winding of any type, Cleaning Slot, Rewinding Fan Motor with Super Enamalled Copper insulated Wire of suitable Gauge and Weight (not less than 350 Gram) providing necessary Insulation Materials, Varnishing, Heating, Reassembling & Testing for Smooth Functioning after Rewinding, Removing the Fan to Site of Work after Rewinding, complete all as specified and as directed.

M&L Preparing old Painted Surfaces of Ceiling Fan of any Sweep including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamelled Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Mild Steel Flat Iron 25x6.0mm Fan Hook/ Clamp including suitable Size Mild Steel Bolts, Nuts & Washers and Similar Small Articles, conforming to Fe-290, Gde-E-165 including Taking down/out Unserviceable Mild Steel Fan Hook/ Clamp of any description, complete all as specified and as directed.

Supply & Hanging Ceiling Fan 1200mm Sweep with Brush Less Direct Current (BLDC) Motor, minimum Air delivery 210 CFM with Serving Value 6.00 BEE, 5 Star rated, 230 Volt, comprising of Blades, Holding Down Rod, Electronic Fan Regulator and Accessories, providing Electric Connection from Ceiling Rose to Fan with and including Twisted Flexible Copper Conductor Cable of suitable Size and Length, 3 Core, complete all as specified and as directed.

M&L Re-hanging/Re-fixing only Ceiling Fan (obtained from BOQ Item No. 2.023 here-in-before after Repaired and Painting) and connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out Unserviceable MCB of any description, complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out Unserviceable MCB of any description, complete all as specified and as directed.

S&F RCBOs 30 Amp, 32 mA, Double Pole for Earth Leakage, Overload and Short Circuit Protection and connecting up including Taking down/out Unservice-able RCBOs of any description, complete all as specified and as directed.

S&F MCB Distribution Board Sheet Metal Enclosure, SPN, 8-way, 240 Volt AC, Single Door with Steel Phosphotised Powder painted, having 200 Amp rated Neutral Bars & Earth Bar, Electrically connecting up including Taking down/out Unserviceable MCB Distribution Board of any description, complete all as specified and as directed.

S&F MCB Distribution Board Sheet Metal Enclosure, SPN, 8-way, 240 Volt AC, Double Doors with Steel Phosphotised Powder painted, having 200 Amp rated Neutral Bars & Earth Bar, Electrically connecting up including Taking down/out Unserviceable MCB Distribution Board of any description, complete all as specified and as directed.

S&F Sheet Metal Enclosure with Socket Plug Top, Single Pole & Neutral with a 2-Pin and Earth Plug and Socket with and including 1 No. MCB Single Pole, 20 Amp, 240 Volt, Electrically connecting up including Taking down/out Unservice-able Sheet Metal Enclosure of any description, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and not exc. 1.50 Metre in Depth for laying of Water Pipe Line, Cable Line, etc., Forming surfaces to required Foundation/ Gradient and getting out in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps with Surplus Soil along the Route of the Water Pipe Line, Cable Line, etc., in Soft/Loose Soil, complete all as specified and as directed.

Drilling/Making Hole (Horizontally) under Roads, Pavement, Hardstanding, etc., by any means suitable for passing GI Tubing 50mm to 80mm bore (dia), complete all as specified and as directed. NOTE : GI Tubing will be Measured & Paid separately under appropriate Items.

Disconnecting & Taking down/out unserviceable LT Cable of any Size and any description including Cable Protection Bricks/ Covers, GI Pipes, etc. from Trenches, Floors, Poles, Walls, complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured & Paid separately under appropriate Items.

Supply & Laying LT Under Ground Cable 1100 Volt grade, XLPE insulated, PVC sheathed heavy duty, armoured with multi-stranded Aluminium Conductor all as per IS:7098 (Part-I)-1998, Cross-sectional Area 10 Sqmm, 2 Core, laid in Trenches, Ducts or through Pipes or fixing to Poles, etc. complete all as specified and as directed. NOTE : Necessary Earth Works, Sand Cushioning, Cable Protection Cover, etc. will be Measured & Paid separately under appropriate Items.

Supply & Laying LT Under Ground Cable 1100 Volt grade, XLPE insulated, PVC sheathed heavy duty, armoured with multi-stranded Aluminium Conductor all as per IS:7098 (Part-I)-1998, Cross-sectional Area 10 Sqmm, 4 Core, laid in Trenches, Ducts or through Pipes or fixing to Poles, etc. complete all as specified and as directed. NOTE : Necessary Earth Works, Sand Cushioning, Cable Protection Cover, etc. will be Measured & Paid separately under appropriate Items.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only will be Measured.

Supply & Laying Unreinforced Pre-cast Concrete Cable Cover of Size 300x180x40mm thick, Class LV, Type 2, Flat, Concrete grade M-20 minimum, complete all as specified and as directed.

M&L Galvanised Steel Tubing Pipe 50mm bore (dia), light grade with Bend, laid in Trenches or under Roads, Pavement, Hardstanding, etc., complete all as specified and as directed.

Supply & Laying HDPE Double Wall Corrugated (DWC) High Density Poly-thene Pipes of Outer Dia 40mm & Inner Dia 32mm, having corrugation on the Outer Wall and Plain surface on the Inner Wall, conforming to IS:14930 (Part I & II), cut to length as per Site Requirements for protection of UG Cable/ in PCC including Cutting Floors, etc. and Making Good the Same with Original Specifi-cation to match the existing adjoining Surfaces, etc., complete all as specified and as directed. MAKE : REX POLY EXTRUSION (ELDREX) or equivalent Make with ISI Marked NOTE : Quoted Unit Rate is inclussive of All accessories for fixing of DWC Pipe with Walls, Roofs, Cable Tray, etc.

Supply, Installation & Commissioning LT Feeder Pillar Box, Factory Made (CPRI Approved/ Tested Manufacturer), Outdoor type, Platform mounted of Size 600x500x450mm, made out of 3.15mm thick CRCA Sheet, suitable for 415 Volt, 3 Phase, 4-Wire System, 50 Hz Supply, having Aluminium Bus-bar 300 Amp for Phases & Neutral, installed on Porcelain/ Epoxy Insulators, Dust Proof and Vermin Proof (IP54), Front & Rear Opening, Double Door Shutters with Locking Arrangements, Epoxy Powder coated, mounted on Mild Steel Angle Iron Frame 50x50x6.0mm and not less than 500mm Height from Natural Ground Level, grouting Angle Iron Legs in Cement Concrete 1:2:4 (20mm graded stone aggregate) Block of Size 300x300x600mm including necessary Formwork, Earthwork, Expossed Angle Iron Frame shall painted with Two Coats of Synethtic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer, providing all Electric Connections and Testing, comprising with and including following Accessories including Taking down/out unserviceable Feeder Pillar Box of any description, complete all as specified and as directed :- INCOMING :- (a) MCCB 125 Amp, 4 Pole, 36 kA, 415 Volt - 01 No. (b) Digital Amp Meter 0-200 Amp, Square Flush Pattern - 01 No. (c) Digital Voltmeter 0-500 Volt, Square Flush Pattern - 01 No. (d) LED Indicator Lamp (RYB) in Incomming Phase - 01 Set (e) MCCB shall be provided with suitable Spreaders of Aluminium Conductor for fixing of Incoming Cables (f) Connection from MCCB to Bus-bars with Solid Aluminium Conductor OUTGOING :- (a) MCCB 63 Amp, 4 Pole, 25 kA, 415 Volt - 03 No.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including Taking down/ out Unserviceable Earthing of any description, complete all as specified and as directed.

PARBIN SIDDIKI

M/S A K BROTHERS

M/S Abhi Traders

Construction House

STANDARD ELECTRIC WINDERS

FREEZCON

RIA CONSTRUCTION

M/S CHANDAN ENTERPRISE