Constt. of community hall with kitchen and bathroom at Bouth

Amount

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth for 1 meter from cutting edge and disposal of surplus excavated earth as directed:

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)(Including all leads and lifts carriages of material by MT/HL)

Providing & laying in Position Cement Concrete of specified grade including curing but excluding the cost of centring & shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) .

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)(Including all leads and lifts carriages of material by MT/HL)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level ,(Including all leads and lifts carriages of material by MT/HL)

Providing & fixing upto floor five level precast cement concrete hollow blocks, including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete. 1 :2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size) (Including all leads and lifts carriages of material by MT/HL)

Centring and shuttering including propping ,strutting etc. & removal of the form work.

Foundations & Footings, bases of columns etc. for mass concrete

Column

Suspended floors, roofs, landings, balconies and access platforms

Edges of slabs and breaks in floors and walls Under 20 cm wide

12mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand)(Including all leads and lifts carriages of material by MT/HL)

15mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand)(Including all leads and lifts carriages of material by MT/HL)

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)(Including all leads and lifts carriages of material by MT/HL)

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate(Including all leads and lifts carriages of material by MT/HL)

Providing and fixing strips in joints of terrazzo/ cement concrete floors. Glass strips 40 mm wide and 4 mm thick

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Distempering with dry distemper of approved brand and manufacture (two or more coats) and of required shade on new work, over and including water thinnable priming coat to give an even shade

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): SAL WOOD

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws Second class deodar wood 30mm thick

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).Second class deodar wood (30MM THICK SHUTTER)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 9 mm thick Marine plywood conforming to

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge Second class deodar wood (30mm thick)

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

250mm x 10mm

100mm x 10mm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete size 300 mm x 16 mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Double rubber stopper

Providing and fixing oxidized M.S. casement stays (straight peg type) with necessary screws etc. complete of 300 mm weighing not less than 200 gms

Providing and fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 ( 1 cement : 4 fine sand) L.M.R.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete(Including all leads and lifts carriages of material by MT/HL)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (Refer CPWD DSR E&M 2018 Item No. 1.10.1). Group c

Group B

GRoup C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (Refer CPWD DSR E&M 2018 Item No. 1.14). 2 x 2.5sqmm + 1 x 2.5 sqmm earth wire

Wiring for light/ power plug with 2 x 4 sqmm FRLs PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 no 4 sqmm FRLs PVC insulated copper conductor single core cable for loop earthing as reqd

Supply and fixing suitable GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 and 15/16 A modular socket outlet 15/16 A modular switch connection etc as reqd

Suppling and fixing 5A to 32A rating, 240/415 V , 10 kA, "C" Curve , miniture circuit breaker suitable for inductive load of following poles in the existing MCB, DB complete with connection, testing and commissioning etc as reqd (single pole)

1200mm size 18/20W LED batten Tubelight fitting

Supply and fixing 9W LED lamp

Supply of ceiling fan 230V 50Hz with double ball bearing with low power consumption of following sweeps including fan regulators 1400mm ceiling fan

Supply and fixing of main service line 16sqmm twin core aluminium cable unarmoured from the LT pole upto the MCV/DB including connection etc as reqd

Supply and fixing following way single pole and neutral sheet steel MCB distribution board, 240V , on surface / recess complete with tinned copper bus bar neutral bus bar, earth bar interconnections power painted including earthing etc as reqd ( without MCB/RCCB/Isolators) 12 way double door

Supply and fixing following modular switch / socket on the existing modular plate , and switch box including connections but excluding modular plate etc as reqd

5/6A switch

3Pin 5/6A socket outle

Supply and fixing modular blanking plate on the exising modular plate and switch box excluding modular plate as reqd

Supplying and fixing suitable G.I. box with modular plate and cover in front on surface or in recess , including providing and fixingg 3 Pin 5/6 A modular socket outlet and 5/6A modular switch connection etc as reqd

Supplying and Fixing of following rating 240/10KA"C" curve , minature circuit breaker suitable for inductive load of following poles in the existing MCB/ DB complete with connections , testing and commissioning as reqd Single pole and Neutral 63A

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :

100 mm inlet and 100 mm outlet

100 mm inlet and 75 mm outlet

Constructing brick masonry chamber for underground C.I. inspection chamber and bend with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:4 ( 1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg ) R.C.C. top slab with 1:1 ½ : 3 mix ( 1 cement : 1 ½ coarse sand : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:5:10 (1 cement: 5 fine sand: 10 graded stone aggregate 40mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line?

Providing and laying PVC soilneaste pipe including bed concrete and all round PVC pipe as per stander design 150mm dia(Prince , finolex , superme make of 4kg/cm2 pressure.)

75mm dia.

100mm dia.

150mm dia.

Providing and fixing PVC loose collar(surpreme/ prince make)

75mm dia.

100mm dia.

150mm dia.

Providing and fixing PVC Plan bend (surpreme/ prince make)

75mm dia.

100mm dia.

150mm dia.

Providing and fixing PVC door bend (surpreme/ prince make)

75mm dia.

100mm dia.

150mm dia.

Providing and placing on terrace on all floor levels polythene water storage tank ISI;12701 marked indicating the bis no with cover and suitable locking arrangements and making the necessary holes for inlet, outlet and overflow pipes including fitting and the base port for tanks syntax , electroplast , star , lotus, or equivalent having ISI make .

Providing and fixing Motor pump of ½ HP of sharp ,bajaj,or equivalent make including fittings (complete job)

Providing and fixing soap dish of approved quality

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making the walls etc.: Internal work-Exposed on wall

15 mm dia. nominal bore .

20 mm dia. nominal bore .

Providing and fixing G.I union in G.I pipes including cutting and threading the pipes and making long screws etc. complete (new work) 15mm dia nominal bore

Providing and fixing wash basin with C.I /M.S brackets 15mm C.P bras pillar taps , 32mm C.P bras waste of standard pattern , including Painting of fittings and brackets , cutting and making the good walls wherever . white vitrerous China . size wash basin 630x450mm with pair of 15mm c.p brass pillar tap .(make cera/equivalent)

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipe and fitting.(make cera/equivalent)

Providing and fixing 600x450mm beveled edge mirror of superior glass of approved quality complete with 6mm thick hard board .ground fixed to wooden cleats with C.P bras screws and washer complete

Providing and fixing PTMT grating of approved quality and colour . circular type 125mm nominal dia with 25mm waste hole(make jaquar/cera/equivalent)

Providing and fixing cp bib cock of approved quality 15mm nominal bore complete job (make jaquar/ cera /equivalent) Short nose

Providing and fixing C.P brass angle valve For basin mixer and gyser points of approved make confirming to . 15mm nominal bore complete job .(make jaquar/cera/equivalent)

Providing and fixing 110mm dia. PVC waste water / sewerage pipe of 4 kg pressure per sqm of supreme / prince/ finoeix make prakash surya

Providing and fixing unplasticised PVC connection pipe with brass union 30cm length 15mm nominal bore

Providing and fixing of 600x120x5 mm glass shelf with edges round off supported on aluminium angle frame with cp brass brackets and guard rail complete fixed with 40 mm long screws etc make jaquar/cera

Providing and fixing ball valve ( brass) of approved quality complete high or low pressure with plastic floats

Providing and fixing PTMP towel ring trapezoidal shape 215mm long 200 mm wide with a minimum distance of 37mm from wall face with concealed fittings arrangements of approved quality and colour , weighing not less than 80 gram

Providing and fixing white vitrous china pedestal type water closet ( European type wc pan) with seat and lid ,10 litre low level pipe with PVC flushing cistern including flush type with manually controlled device conforming to IS:7231 with all fittings and fixures, complete including cutting and making good the walls and floors where ever required.(make cera/equivalent)

Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design

Kitchen sink without drain board 610x510mm bowl depth 200mm

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 110 mm dia.

Providing and fixing CIB of approved size by way of making foundation in M10, Brickwork in 1:6 cement mortar including plastering with 1:4 cement mortar, painting and writings as per the direction of engineer in-charge including supply of materials, carriages all complete job.

RATTAN CHAND GOVT CONTRACTOR

JIA LAL

Prithi Singh