Construction of control room building, boundary wall, water supply arrangement and other civil works at 33 KV S/S Jatoli-Rathbhan (A-III, Bharatpur)

PART-A

B-1/1.31 : Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

B-1/1.8 : Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or rains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils.

1.34 Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20%

B-1/1.36 Diluting and injection Chloropyrifos Emulsifiable concentrate 20% with 1% concentration for PRE-CONSTRUCTIONAL Anti termite treatment as per IS 6313 part III as amended from time to time and creating a continuous chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filling, junction of wall and floor along the external perimeter of building expansion joints, over the top surface of consolidated earth of which aproch is to be laid surrounding of pipes and conduits etc. complete as per specification (Plinth floor area only shall be measured for payment and excluding the cost of chemical emulsion) .

B-3/3.1.6 : Providing and laying in Position Cement Concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M15 grade Nominal Mix 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size).

B-6/6.1.6 : Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand).

B-5/5.3.2 : Add extra for Square or Rectangular Pillars in Superstructre brick work up to five storey upto 45 cm length and two corners are free.

B-5/5.2.2 : Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand)

B-4/4.1 : Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix

B-4/4.3 : Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc. M20 grade Nominal Mix / Design Mix

B-4/4.9 : Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc.

B-4/4.10.2 : Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel props and removal of formwork for upto floor five level for : Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor locks, sills, chhajjas, lintel, beam, plinth beam etc.

B-4/4.13.3 : Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Thermo-mechanically Treated bars (Conforming of relevent IS code)

B-9/9.19 Providing and fixing steel glazed doors windows and ventilator shutters of standard rolled steel section (IS 1038-1983) joints mitred and welded with steel lugs 13x3mm, 10cm. long embedded in cement concrete block 15x10x10cm. of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws with fixing clips or with bolts and nuts as required including providing and fixing of plain glass panes 4mm thick with cooper glazing clips and special metal sash putty of approved make or metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handles peg stay etc. as required : B-9.19.3 Windows side hung /Ventilators top or centre hung (openable)

B-9.19.2 Windows fixed

B-9/9.26 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance.

B-9/9.27 Providing and fixing Square bars or other flat welded to window, ventilatiors etc.

B-10/10.17.1 Grading roof for water proofing treatment with water proffing compound : Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

B-10/10.22 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design

B-3/3.8 : Providing & fixing precast cement concrete coping 1 : 2 : 4 mix 50mm thick complete as per specification :

B-5/5.8.3 : Half brick masonry in Superstructure , above plinth level upto floor V level using bricks of designation 75 Cement mortar 1 : 6 (1 cement : 6 coarse sand).

B-6/6.18.1 : Supplying and fixing stone lintels/bed plates of approved quarry rough dressed in cement mortar 1:4 : Upto 15 cm. thick.

B-11/11.17.3 Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand): Dark shade using ordinary cement.

B-12/12.7 : Finishing with neat cement (punning).

B-12/12.3 : Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :B-12/12.3.2 : 20mm thick.

B-12/12.3.3 : 12 mm thick.

B-12/12.19 : Making grooves as per design in plaster 10mm to 20mm wide.

B-12/12.5 : 6 mm thick cement plaster to ceiling of mix 1:3 (1cement : 3-fine sand)

B-12/12.20 : Making of drip course (Tapka) in cement sand mortar 1:6 width upto 40 mm and 10 mm thick as per approved design

B-12/12.22.1 : Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete : New Plastered Surface (three or more coats)

B-12/12.37 : Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: B-12/12.37.1 : New work (two or more coats) over and including scrapping and priming coat with cement primer.

B-12/12.42: Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ).

B-12/12.46: Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : B-12/12.46.1: Two or more coats on new work

B-6/6.17.3 : Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges :Kota stone minimum 30mm thick.

B-11/11.18.2 Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand): For area of each slab from 2001 to 5000 Sq.Cm

B-11/11.19.1 Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete: For area of each slab upto 2001 sq.cm.

B-9/9.5 : Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

B-8/8.13.2.1 : Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal dehyderesin in glue both sides with approved steel fittings complete as per annexure 'A': Commercial Veneer both side 30 mm thick . Commercial Veneer both side.

B-12/12.45.1: Applying priming coat : With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood.

B-9/9.17 Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint

B-9/9.17+9.17.1 Providing and fixing M.S. sheet 1mm thick double leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint:

B-11/11.26 : Random rubble dry stone Kharanja under floor.

B-9/9.39 Providing and fixing of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25 mmx 1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting in approved shade with deco paint of approved quality complete as per direction of Engineer In Charge

E-24.67.3 : Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type Fire Extinguisher (Stored Pressure type) conforming to IS:15683:2018 , Powder coated Internal & External Surface Deep drawn cylinder body of Mild Steel CR2 grade conforming to IS: 513, Squeeze grip Forged brass release valve with Inbuilt safety release device, Diaphragm Type, 0 to 28 bar range pressure gauge, 450 mm long EPDM discharge tube, QR code for Product Traceability including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificate from OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 6kg

B-7/7.12: Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar).

B-7/7.13 : Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed

B-9/9.38.3 Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size.: Welded mesh 25 mmx 25 mm x 2.1 mm

B-9/9.8+9.8.1 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide :with Extra if square,rectangular hollow tubelar sections are used or grill made by flats only

B-9/9.2 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete

B-3/3.1.2 : Providing and laying in Position Cement Concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M15 grade Nominal Mix 1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

B-11/11.38.3 (A) : Providing and laying of paver block as per IS 15658 : 2006 (Indian standard for precast concrete block for paving- specification) and IRC : SP:63-2004 (guidelines for the use of interlocking concrete block pavement) : M-40,80mm thick to be used in medium- traffic ( Medium traffic is defined as a daily traffic of 150-450 commercial vehicles exceeding 30 KN laden weight, or an equivalent of 0.5 to 2.0 MSA for a design life of 20 years.) like city streets, small and medium market roads, low volume roads, utility cuts on arterial roads, etc:Category A Denated units to key into each other on four faces zigzag shape as per IRC SP 63:2004

B-11/11.29:- Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin- charge).

S-1/1.2.2: P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 580x440mm.

S-1/1.14.1: P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete. : Flat Back (small) size 456x355x265mm.

S-2/2.14.9 : P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make :Brass / Gun metal Half-turn wt. 1 Kg. of approved quality / make, 25mm nominal bore.

S-2/2.7.2 : P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: P.V.C.heavy duty, 15mm nominal bore.

S-1/1.36.4 :P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall :Size 580 mm x 450 mm.

S-2/2.12.1 : P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15mm.Brass (IS : 8931 marked)

S-2/2.13.3 : P & F 15 mm. Dia Connection Pipe of approved quality/make :PVC pipe with C.P. Brass nuts upto length, 450mm

S-1/1.48.2 : P & F Grating of approved quality/make: Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make

S-1/1.45.2 : P & F Looking Mirrors with P.V.C. frame of approved make as per direction of Engineer-in-charge: Oval shape 450x350 mm

S-1/1.47.2 : P & F Towel Rail or Ring of approved quality/make: C.P. brass Towel Rail elbow type with concealed screws size 600 mm (Heavy duty).

S-2/2.26+2.27.1 : P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design including Hoisting Charges for first floor :500 litres capacity. (S-2.26.3+2.27.1)

S-2/2.7.2 : P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make: P.V.C.heavy duty, 15mm nominal bore.

S-2/2.38: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,)S-2/2.38.2: 20mm nominal size

S-2/2.38.3: 25mm nominal size

S-2/2.39: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work).S-2/2.39.2: 20mm nominal size

S-2/2.39.3: 25mm nominal size

S-2/2.15 : P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make ::(a)Gun-metal 15mm nominal bore (S-2.15.1)

(b)Gun-metal 25mm nominal bore (S-2.15.3)

S-3/(3.19.1+3.19.3) : Construction of manhole in all type of soil inner size 90 X 60 Cm. 230 mm thick brick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead.Depth up to 0.5 M

S-3/3.22.3 : Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300 mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1 : 3, Ralthal, Kharanja, 40 mm thick M-15 grade C.C flooring , earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr.: size 240 cm dia outside and 240 cm depth

S-3/3.27.1 : Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M-15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:Size 200x100x130 cm.(for 10 users) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 8mm ϕ @15 cm c/c bothways including shuttering complete in all respect.

S-3/3.16.3: P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. : 110 mm dia

S-3/3.17: P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant:S-3/3.17.8 (ii): bend 45: 110 mm

S-3/3.17.9 (ii): bend 87.5: 110 mm

S-3/3.17.12 (ii): Vent Cowel: 110 mm

S-3/3.17.15 (ii): pipe clip: 110 mm

S-3/3.16.5.1: Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height = Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc. PVC pipe 110 mm dia

S-1/1.38.9.2 : P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor :1.0 mm thick stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make as per Engineer-in-charge with large waste coupling.overall size (inches)22 x 18 x 7 , bowl size (inches) 20x16x7.

S-2/2.3.2: Making connection of G.I. distribution branch with G.I. main including all fitting.: Beyond 25mm & upto 100mm dia

E-15.7.2 : Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .1200 mm Sweep BEE 2 Star rated (service value >=4.5 to < 5 )

E-1.1: Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & it's ISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thick Hot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. (A) Short point (up to 3 mtr.) (1.1.1)

(B) Medium point (up to 6 mtr.) (1.1.2)

(C) Long point (up to 10 mtr.) (1.1.3)

E-3.3.1 : Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC Trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box, modular 10A switch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. on board

E-4.1 : Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR(a) E-4.1.7 : 2 X 2.5 sq.mm + 1.5 sq. mm

(b) E-4.1.14 : 2 X 4.0 sq. mm +2.5 sq. mm

E-7.36 :Providing and fixing of power plug point with non modular accessories as per PWD specification for electrical Works with Galvanized box of 1.2 mm thick with earth terminal with suitable size phenolic laminated sheet (IS : 2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet making connection , testing , etc. as required. . For specification of Wiring accessories refer Chapter E - 07 related item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

E-6.1.1.2 : Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. Single pole MCB (With B/C curve tripping Characteristics) 6 A to 32 A rating

E-6.2.1.2 : Providing & Fixing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR. Double pole isolator 63 A rating

E-6.9.2 : Providing & Fixing of Recessed/surface mounting heavy duty Enclosure made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted complete with din rail making internal DB terminations with copper lugs, detachable gland plate, including making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR Suitable for Six / Eight module for MCB/ RCCB.

E-7.12 : Providing & Fixing of ISI marked (IS:371) 6 amp surface type 3 pin ceiling rose with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

E-7.13 : Providing & Fixing of ISI marked (IS:1258) batten/angle lamp holder with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screwsincluding making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

E-5.9 : P & F 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR

E-7.20 : Providing & Fixing of IS 11037:1984 marked non modular socket size flush type 120 watt rotary minimum 5 step fan regulator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

E-17/ (17.2.2): Providing & Fixing of energy efficient direct fit (Retrofit) Polycarbonate/ Glass housing SMD Mid Power LED tube rod (with integral driver & alumn. heat sink ), on existing fixture. system lumen efficacy ≥ 100 lm/Watt output, internal surge protection of 2.5 KV ,THD < 20% ,p.f.≥0.95,CRI >80 , life time of minimum 35000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80)certificate / Report from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 1200mm , Min. Lumens output 2000 lm LED Tube rod with Polycarbonate Housing.

E-18.12 :Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass cover and secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <750mA. The luminaire shall be BIS certified and Trade mark certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum 70% lumen maintened , CRI >70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .: (a)LED Street Light fixture with Minimum lumen output 2450 lm (E-18.12.1)

(b)LED Street Light fixture with Minimum lumen output 11225 lm (E-18.12.6)

E-11.1 : Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Un-Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR(a) 4.0 sq. Mm : 2 core (ARM)( E-11.1.1.1)

(b) 6.0 sq. Mm : 2 core (ARM) ( E-11.1.2.1)

E-14.2 :Plate Earthing as per IS:3043 with Hot dipped G.I. Earth plate of size 600mm x 600mm x 6.0mm by embodying 3 to 4 mtr. below the ground level with 20 mm dia. G.I. 'B' class watering Pipe ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height 250 to 300 mm. and embodying the pipe complete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or less as required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .

E-14.6.6 : Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles, making connection with GI/Cu purity purity >95% thimble etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR . 10 SWG copper. Wire

E-18.18.2 : Providing & Fixing of Street light bracket made out from following size of ' B ' class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with heavy duty pole clamp, Saddles suitable fastners etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .25 mm dia.

E-15.12.1 : Providing & Fixing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single phase Exhaust fan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .300 mm sweep(900/1400 RPM)

P-2.1.2: Const. of tubewell from ground level & upto 100 mtr. Depth to accommodate housing and assembly pipe in all type of alluvium strata unconsolidated formations such as pebbles boulders etc. by percussion/ rotary drilling method as per IS: 2800 part 1: 1991 and IS: 2800 part 2: 1979 (both amended upto date) and technical specifications,with gravel as per IS :4097-1967 and it's packing as per IS:2800 (Part I&ll) 1979 as amended upto date (the work includes the cost of gravel & it"s primary packing and packing during development,lowering of housing & strainer assembly pipes with supply and wrapping of coir-rope, wherever necessary for arresting fine sand particals and development work, but excluding the cost of housing and stainer pipe assembly). The work would be compeled after obtaining sand free water. nominal bore 200 mm dia.

P-2.1.2+2.1.4: Const. of tubewell from 100 mtr. Depth to 200 mtr. Depth accommodate housing and assembly pipe in all type of alluvium strata unconsolidated formations such as pebbles boulders etc. by percussion/ rotary drilling method as per IS: 2800 part 1: 1991 and IS: 2800 part 2: 1979 (both amended upto date) and technical specifications,with gravel as per IS :4097-1967 and it's packing as per IS:2800 (Part I&ll) 1979 as amended upto date (the work includes the cost of gravel & it"s primary packing and packing during development,lowering of housing & strainer assembly pipes with supply and wrapping of coir-rope, wherever necessary for arresting fine sand particals and development work, but excluding the cost of housing and stainer pipe assembly). The work would be compeled after obtaining sand free water. nominal bore 200 mm dia.

P-2.11 Supply of ERW M.S. black casing pipe ISI marked (IS : 4270/2001) or amended upto date of following sizes : (b) 200 mm dia NB (Thickness of pipe 5.4mm & mass of tube 28.46kg/m) (P-2.11.2)

P-2.12 : Labour charg for making slots on blank pipes made of ERW M.S. black casing pipe ISI marked of following sizes, the sloting should be as per IS : 8100/1985: P-2.12.3 : (b) 200 mm dia nominal bore of 5.4 mm thickness (P-2.12.3)

P-2.10: Development of tube well having depth upto 250 mtr as per IS:11189-1985 and IS: 2800 (Part-I) - 1991 (both amended up to date ) using suitable methods to give sand free water for required yield of the gravel packed tube well.

P-2.22 : S & F M.S. clamp set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set.

S-4.8.4 : S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size: 200mm dia

E-21/21.2.2.1: Supply & fixing of PVC threaded casing pipes for Tube well (IS 12818:1992) of 3mtr. Each for depth up to 1200 ft. Plain and strainer Casing CS for Depth upto 400ft. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR .: more than 400 ft to 1200 ft. Depth: 40mm dia

E-4.7.4 : P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with Electrical BSR 2022. (6.0 Sq.mm 3 core flat / Round)

E-21.6.1 : SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with electrical BSR 2022 . 100 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively. (b)(E-21.6.1.4) 3.0 HP, 1-Ø, (40 -170)Mtr, (60- 20) LPM Copper Wound

E-21.3.1: Providing & Laying of Polypropylene rope Confirming to IS:5175 for submersible pump of following sizes. complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with electrical BSR 2022 : 12mm (suitable up to 50 mm OD pipe)

Item Rate BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

PART- B (Item Rate Basis)

Earth work in filling of Excavated earth except black cotton soil with watering and compaction of spreaded earth in 15-30 cm layers leveled and neatly dressed as per requirement of site and direction of engineer in charge, work includes cost of earth with taxes, loading , unloading, transporation labour, water and T&P etc. complete with all lead and lift

Supply and spreading of crusher dust free of organic matter including stacking spreading and laying in yard as per standard specification including all lead and lift, Transportation, labour, loading unloading, T&P required for spreading of crusher dust work as per direction ot Engineer in Charge including dressing ground upto 15cm depth.

Supply, stacking, spreading & hand ramming of quarry rubbish in layer not exceeding 15cm (loose) incl. all lead & lift, transportation, loading unloading with watering including labour T&P machinery water etc. complete in all respect finishing in lying level and camber as per direction of Engineer in charges

Supply stacking and spreading of graded crusher brocken hard stone aggregate fee from organic matter including stacking & spreading in yard / trenches as per the standard specification of size 40mm to 63 mm incl. all lead & lift, transportation, labour, loading, unloading & T&P required for gravelling work as per direction if Engineer in charge incl. dressing & leveling.

Providing & Fixing of four no. 10 ltr capacity steel bucket and filling of bucket by sand & approprite size of steel stand for fixing the steel bucket. the stand made by 65X65X6mm M.S angles with two or more coats of enamel paints including primer coat on all buckets & Stand including all meterial labour T&P and other required accessories. The size & Shape of bucket & stand (length of 2no, vertical posts 1.50mtr, length each 2no Horizontal member length 0.90 mtr. each and hold fast 2 No. 0.15 Mtr each) including E/W & Dully grouted in CC 1:2:4 (2X30X30X45CM) as per direction of Engineer in Charge. Including painting with primer & postman red colour paint and letter writing "FIRE"

Supply of tubular steel table for office purpose with particle board of one side laminted teak facing ISI marked 25 mm thickness and side steel rack in both sides with one shelve in each side with locking arrangement. Table sixe 1120x710x760 mm, Top size 1120x710x25 mm, frame size 1020x550x735 mm including primer and zinc paint complete with frame of 25x25 mm square medium pipe as per instruction of engineer in charge.

Supply of chair having frame of 19mm round pipe of (16 gauge) and having seat and back of 18 gauge perforated steel sheet of 16"x16" and 16"x8" (semicircular) respectively and duly painting with powder coating paint (size of chair LxBxH= 20"x18"x33")

Displaying Imporatant Telephone Numbers for Existing Bldg. wall scraping colour & painting & writing the name & phone no. as per direction of Engineer Incharge.

Displaying of safety equipment on existing bldg. wall in (size 1800x750 mm) including scrapping of colour, painting & writing different items name as per directions of Engineer -in-charge.

Supply & Planting of shady plants (Neem, Peepal, Goolar, Jamun, lmli or other specified) including the following activities : 1. Preparation of soil including cleaning & removing of unwanted shrubs removal of stones & garbage. 2. Supply of plant at site of two years of age & height more than 1.5O Mtr. 3. Supply of dry manure (Farm yard manure organic). 4. Supply of Insecticides. 5. Digging of pits size 60x60x60 cms. Including removal of stones, Manuring application of insecticides & watering at least 15 liter per plant after planting. 6. Maintenance of plant to be done by the contractor upto S.D. period. If the plant dies during maintenance, contarctor has to replace same height plant at his own Cost.

P&F sign board as per approved drawing and specification made of M.S sheet of 1.6mm thick of size 1200X900 mm stiffened by flat 20X3mm on both sides all arround the plate & duly framed with 32mm dia medium M.S black pipe fixed on frame of 50mm OD medium pipe (Vertical post 3600mm, 3000mm above ground level with angle iron hold fast 35X35X5mm with Horizantal member 1500mm to be jointed with flat 40X6mm and post embeded in cement concrete block M-15 grade of 450X450X750mm size below ground level as directed by E/. all MS will be stove enameled and both side lettering, figuring and border on sheet with ready mix synthetic enamelled paint of superior quality in required shade and colour etc. complete in all respect all support framed post & steel tubes will be painted with primer and two coats of enamel paint as per specification & Direction of E/. Over all size 1500 X 1200mm.

Please Enable Macros to View BoQ information