REPAIR TO FOOTPATH, CULVERTS, FENCING, GATE AND COMPOUND WALL WITH DRAINS IN AOR OF AGE B/R-I AT BB CANTT, SRINAGAR

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling fencing wire mesh, any type complete all as specified and as directed.

M&L for cement concrete (1:2:4), type B2 (using 40mm graded crushed stone aggregates) as in foundation, filling in and mass concrete etc, complete all as specified and as directed.

M&L for mild steel work in hand rails, half round or other steel section or core for wooden hand -rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply only chain link MS galvanisd fencing, any size or type complete all as specified and as directed. Note : Actual weight of the fencing shall be ascertained by Board of Officers to be convened by GE.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, but length of bolt exc 5cm but n exc 10cm long and dia of neck 5 to 10mm, complete all as specified and as directed.

S&F in repair galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed. (Note : Each line wire to be measured)

M&L for preparation of new or previously untreated steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and as directed.

M&L for mild steel round bars, conforming to Gde-I (IS : 432 Part-I) Part-I, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips,complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition), complete all as specified and as directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facings, dressed stonework and precast concrete articles, complete all as specified and directed by Engineer-in-Charge.

M&L for brickwork with old size sub class 'B' bricks straight or curved on plan exc 6m mean radius and built in CM (1:6) etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor & pavings n exc 15 cm thick below or above ground level complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8), type D2 (using 40mm graded crushed stone aggregates) as in sub base or floors etc. complete all as specified and as directed.

M&L for 25mm thick cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base/ levelling course complete all as specified and as directed.

M&L for rubber moulded chequered cement concrete tiles with grey cement and pigments 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) etc complete all as specified and as directed.

M&L for exterior wall cladding tiles of size 300mmx 600mm of 7 o 8mm thick designer tiles coloured etc set and jointed in cement slurry and pointed in coloured cement to match the shade of tile, over and including 15 mm thick backing coat in CM (1:4) on brick work or concrete surfaces and finished even and fair to receive tiles complete all as specified and as direcrted.

M&L for rendering 15mm thick in CM (1:4) on brick work or concrete surfaces rendering is to be finished even and smooth (without using extra cement) complete all as specified and as directed.

M&L for preparation of newly plastered or unplastered wall surfaces and applying three costs of white wash complete all as specified and as directed.

M&L for cement concerte (1:2:4), type B1 (using 20mm graded crushed stone aggregates) as in cills, steps, seismic and other similar bands, plinth courses, copings, kneelers, apex stones, bed plates, bond stones etc. including weathering, slightly rounded or chamfered angles and throating including necessary use and waste of formwork, complete all as specified and as directed.

M&L for precast cement concrete (1:2:4), type B1 (using 20mm graded crushed stone aggregates) in cover slab (for manholes etc.), shelves and similar work with plain faces including necessary moulds and setting in cement mortar (1:4), complete all as specified and as directed.

M&L for framed work such as in angle iron frames for manhole covers and similar work confirming to Fe 290 grade E-165 complete all as specified and as directed.

S&F 150 mm (When open) width of recess between flenges parliamemtary hinges mild steel cold rolled complete all as specified and as directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410 -W grade E-250 Quality A complete all as specified and as directed.

M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

M/S NORTHERN ELECTRICAL WORKS

M/S SHIMAR STAR GLACIER

M/s Lal Enterprises

M/S BASHIR AHMAD MIR

Alishan Builders

M/S Mian Rashid Wani

M/S SUHEEL CONSTRUCTIONS

M/S MAHIR MUNEER