A/SAD/IGAR(S)27/32/25-26

Amount

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed in all kinds of soil.

Earth work in excavation by mechanical / manual means in fdn trenches or drain n-exc 1.5 m in cluding dressing of side and bottoms, lift up to n. exc 1.5 m in depth and getting out excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m. in all kinds of soil.

Providing and laying in position cement concrete 1:4:8 as in foundation filling and mass concrete of specified grade excluding the cost of centering and shuttering, All work up to plinth level.

Providing and laying in position specified grade of reinforced cement concrete, 1:2:4 as in base of column & up to plinth height, excluding the cost of centering, shuttering, finishing and reinforcement, All work up to plinth level.

Reinforced cement concrete work in 1:2:4 as in roof slab, lintel band/beam and Chajja .

Centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting work to sides of Lintels, beams, plinth beams, girders, bressumers and cantilevers side and sofits rough finishing surface of concret.

Centering and shuttering including strutting work to Suspended floors, roofs, landings, balconies and access platform surface of concret.

Providing and laying in Steel reinforcement TMT bar for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Column -12 mm dia bar Stub Column -10 mm dia bar PB (12 mm dia bar) PB & LB (10 mm dia bar)

Supply and fixing of 15x8 m PFT shelter as per drg No. 5 Sect/ ENGR/ 544, Sheet No 1/3 to 3/3, Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position incl nut, bolt & washer, col foundation bolt and applying a priming coat of approved steel primer etc all complete framing wk.

Fixing only for precoated galvanised iron profile sheets with two corrugation side lap. The sheet shall be fixed using self drilling with L-type or J-type of hook on CGI sheet.( Sheet supplyed by CP Store)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm thick, Zinc coating, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws for Ridges plain (500 - 600 mm) complete.

M/L for MS flat iron 40x6mm thick as in wind tie.

Providing and fixing false ceiling of 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks) including fixing with frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting. .

Providing and laying in Brick work with common burnt clay modular bricks of class designation in foundation and plinth in cm 1:6.

Providing and laying in Half brick masonry with common burnt clay F.P.S.(non modular) bricks of class designation 7.5 in superstructure above plinth level up to roof V level. sizes in cm 1:6.

Providing and laying in plastering 6 mm thick cm 1:3 on surface on ceiling/slab soffits ect.

M/L for plastering 15 mm thick cm 1:4 on external surfaces.

Wall triangle Junction

M/L for plastering 20 mm thick cm 1:6 on internal surfaces.

Cement plaster 18 mm thick in two coats under layer 12 mm thick cement plaster 1:5 and a top layer 6 mm thick cement plaster 1:3 finished with a floating coat of neat cement.

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in 75 (100) mm thick back filling for pitching including supplying of required materials and consolidation etc. complete with Stone aggregate 40 mm nominal size

Providing and laying in position cement concrete 1:4:8, 75mm thick as in floor sub filling and mass concrete of specified grade excluding the cost of centering and shuttering.

Providing and laying in Cement concrete pavement with 1:2:4, aggregate 12.5 mm nominal size, including finishing complete.

Providing and laying vitrified floor tiles of 1st quality 7 mm to 8 mm thick, size up to 50x50 cm of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 , including pointing the joints with white cement and matching pigments etc., complete.

Earth work in excavation by mechanical / manual means in fdn trenches or drain n-exc 1.5 m in cluding dressing of side and bottoms, lift up to n. exc 1.5 m in depth and getting out excavated soil and disposal of surplus excavated soil as directed,within a lead of 50 m. in all kinds of soil for Making plinth protection.

Making plinth protection 75 mm thick of cement concrete 1:3:6 over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth with neat cement punning.

Making for Sub base of drain,100 mm thick of cement concrete 1:4:8 and mass concrete of specified grade excluding the cost of centering and shuttering, All work up to plinth level. .

Making plinth protection drain 75 mm thick of cement concrete 1:3:6.with fine sand, including finishing the top smooth with neat cement punning. .

Making finishing the top smooth with neat cement punning for drain.

M/L for form work to sides of drain surface.

Providing and fixing to 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix including finishing the top smooth for drain .

Providing and fixing frame of 40x40x6mm angle iron including butt hinges, lock strikeplate , hollfast and all necessary fittings complete, including applying a priming coat of steel primer with two coat synthetic enamel paint .

Providing and fixing for ISI marked flush door shutter 30 mm thick non decorative type, core of block board or cross bands and face veneers on both faces including stainless steel hinges with necessary screws complet works.

Providing and fixing for fly proofing door shutter 35 mm thick non decorative type and 2nd class HW seasoned & chemically treated Hollock wood, with provn of galvanised MS wire gauge of average width of aperture 1.40 mm in both direction with wire of dia 0.63mm with 2nd class teak wood beading 62x19mm complet works and including stainless steel hinges with necessary screws complet works.

Providing and fixing for ISI marked stainless steel tower bolts 200x10 mm size with necessary screws complet works.

Providing and fixing for ISI marked stainless steel handles 100 mm with necessary screws complet works.

M/L for door painting with two coats of synthetic enamel paint over one coat of wood primer for wood surfaces.

Providing and fixing of glazed & fly proofing windows, steel work welded in built up sections/ framed work size 25x25x5 mm including cutting,hoisting, fixing in position with providing for sash bars, butt hinges, lock strikeplate , hollfast, 4mm thick glass pan with glazing clips and sash putty of approved make, galvanised MS wiremess gage with average width of aperture 1.4mm in both directions with wire of dia 0.63 mm with steel beading, and all necessary fittings complete, and applying a priming coat of steel primer with two coat synthetic enamel paint .

Finishing for New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)walls with Acrylic Smooth exterior paint of required shade

S&F for point wiring with PVC cashing capping ,with modular type switch wiring for light /ceiling fan/exhaust fan/ call bell point/ 5amp point with 1.5 sqmm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular type switch, modular plate phenolic laminated sheet, suitable size GI box and earthing the point with 1.5 sqmm . FR PVC insulated copper conductor single core cable ect. as required group A.

Supplying and fixing brass batten/ angle holder including with back plate suitable fitting connection etc. as required.

S&F for concealed power plug wiring with PVC conduit (2x2.5 sqmm+1 X 2.5 sq. mm earth wire) FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit,with earthing the point with 1.5 sqmm .

S&F for modular type 6 amp switch & socket 5 pin outlet including connections ect complet wk.

S&F for concealed power plug wiring with PVC conduit (2x4 sqmm) FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit,with earthing the point with 1.5 sqmm .

S&F for modular type 16 amp switch & socket, 6pin outlet including connections ect complete wk.

S&F for modular plate along with GI box 4 modular base & cover plate size 125x75mm for modular switches in recess ect. Complete wk.

M/L for ceiling rose, surface bakelite, 65x50 mm, two to three terminals.

S&F for modular stepped type electronic fan regulator on the exising modular plate switch box including connections ect complete wk.

Instalation, testing and commissioning of ceiling fan including wiring the down rods with 1.5 sqmm FR PVC insulated copper conductor single core cable etc complete wk.

M&L for Fan hooks made out of 16mm dia MS Rod

S/F MCB single pole 32 amps rating, 240/415 volts, circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Ditto- but MCB single pole 32 amps with neutral .

S/F DBS sheet metal enclosures for MCB to be used 2 + 4 way, Single door with bus bar.

supply & instalation, testing and commissioning of 63 amp DP MCB isolater.

supply & instalation, testing and commissioning of earthing with G.I. earth plate 600X600X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as requiredect complete wk.

supply & instalation 25mmx5mm GI earth strip in and on surfaces for connection including soldering ect complete wk.

M/L for twin core PVC insulated sheathed copper conductor 2x2.5 sq mm + 1x2.5 Sqmm earth wire in PVC cashing caping in sub main.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Service Taxes If any Service Taxes If any Services If any

M/S P ENTERPRISES (BID ID -3292845)

M/S NIRBHAY KUMAR (BID ID -3292552)