Balance work for Renovation and interior furnishing of auditorium at Indian Academy of Highway Engineers campus, Noida

Amount

Item Description

INTERIOR WORK

FIRE and CCTV

STAGE FURNISHING

FURNITURE

AUDIO-VIDEO SYSTEM

ELECTRICAL WORK ITEM

PLUMBING

CIVIL WORK

DISMANTLING

Description of Work / Item(s)

Amount

CIVIL WORK

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Make: Kajaria, Orient, Somany, HR Johnson, Vermora

Providing and laying Anti skid Vitrified tiles in 450 x 450 mm (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Tile size 450 x 450 (Make- Kajaria/ Orient/ Somany/ H.R. Johnson/Vermora )

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Size of Tile 600x600 mm

TILE GROUTING :- Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge.

Size of Tile 600x600 mm

Description of Work / Item(s)

Amount

DISMANTLING

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-inCharge.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Thickness above 25 mm up to 40 mm

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Description of Work / Item(s)

Amount

INTERIOR WORK

False Ceiling

Providing and fixing false ceiling including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable forboard, all as per manufacturer's specification and and also including the cost of making openings for light fittings, grills, diffusers, cut-outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: Make Lafarge, Saint Gobain, USG Boral, Armstrong

12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I

Providing & Fixing of Soft Fibre Acoustical Suspended Ceiling System with Beveled Tegular Edge Tiles With 15mm Exposed Grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.9 - 1.0, Colour Black, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600x600x15mm, suitable for Green Building application, with Recycled content of 66% GW & 74% RW. The tile shall be laid on 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38 mm and a load carrying capacity of 12.5 Kgs/M2 (as per standard installation layout mentioned below) & pull out strength of 100Kgs. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system INSTALLATION:To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications below) at 1200mm maximum. The First/ Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum. Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure. SUSPENSION SYSTEM accessories manufactured and supplied consisting of M6 Anchor Fasteners with hanger hole, pre Straightened Hanger wire of dia – 2.5 mm of 1.80 m length having a tensile strength of 344-413 MPa and a minimum pull strength of 110 kgs. (Adjustable hook clips of 0.7mm thick, galvanized spring steel can also be used for installation purpose as an additional accessory. The adjustable clip also consists of a 4 mm aquiline wire to be used with the main runner). Make Hunter Douglas, Linder,armstrong

Providing and Fixing 40 mm thick, pre-formed fiberglass blades with size of 200x1200mm, with laminated scrim finish on all sides and edges, Acoustical performance of 0.65 NRC (for 400mm high x 40mm thick with baffles at 400mm row centres. Overall depth of construction 1000 mm) in standard White color with Light reflectance 87%, or in the color specified by the Engineer-in-Charge, Fire Performance Class B – s1, d0 as per En 13501-1 and having a recycled content of 80%. INSTALLATION WITH DECK HANGING KIT: The Blades shall be factory fitted with “female inserts” on both sides. The blades to be suspended individually using the Deck Hanging kitcomprising of gripper structure anchors with an outer diameter of 16 mm and height 23 mm, aircraft cables of 1.5mm dia 2.44 LM in length and bottom end cable adjusters of 8.9mm outer diameter. Blades must be installed with minimum 100 mm on-centre spacing.Hanger Wire Attachment to Structure: Attach the gripper structureanchor to the structure with a fastener that will carry the full weight of the blades. Insert the end of the cable into the gripper anchor cap. Screw the gripper anchor cap completely into the gripper structure anchor. Insert Suspension Cables: The panel is to be suspended using the aircraft cables which are suspended from the soffit using the gripper structure anchors and its other end passing through the bottom end cable adjuster. The height & level of the panels can be adjusted using the bottom end cable adjusters. Suspend the Blade: Locate the two factory fitted female inserts on the blades. Suspend the Blades by screwing the bottom end of the cable adjuster into the female inserts.Installation to be carried out by Trained Installation team & Installation should be carried out as per recommended procedure. Make Hunter Douglas, Linder, armstrong

WALL TREATMENT

Providing and Fixing Channeled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm or as required by the Architect/ approving engineer, made of a Moisture Resistant fibre board with minimum 595 Kg/M3 density substrate with a laminated facing as per the approved shade & finish and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the visible surface has a perforation of 3mm width and 13mm of visible panel each. The edges of the panels shall be “tongue-and-grooved” to receive special clips for installation. The back of the perforated panel shall have sound absorbing non-woven acoustical fleece having NRC of 0.60. The panels shall be mounted on special aluminium splines (keel) using clips provided and approved by the Architect/ Engineer-in-Charge. INSTALLATION: Install MS battens (provided by others) of section 50x50mm tubular or as approved by the Architect on the solid wall horizontally using screws and plugs at spacing of 600mm centre-to-centre .The system is backline with 50 mm Roxul Rockwool insulation@48kg density and along with all accessories Screw the aluminium extruded keel for channelled woodworks provided over the lowest and second wooden batten at an on-centre distance of 600mm. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer-in-Charge and insert the tongue end of the panel in the skirting. Place the inside clip on the groove end of the panel along the Al keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into the groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden moulding of matching colour (provided by others). Installation to be carried out byTrained Installation team & Installation should be carried out as per recommended procedure. MAKE Topkaustik, Wood Fit, Armstrong, VEILS ( Note: Existing Frame for Wall panel is to be used after adjusting it according to profile of wall panel)

Providing and fixing of 68 mm thick wall panel system using Polyester fiber acoustic mat finish panel 9mm thick @ 200kg/m3 density with Class A fire rating as per ASTM E 84 & thermal conductivity 0.034w/mk with desired acoustic management 0.80 NRC. The G.I. frame of thickness 0.50 consists of GI metal stud frame of size 50mm having one flange of 41mm and other of 44mm placed @ every 600 mm c/c in vertical direction. These studs are placed at floor and ceiling channels of 76 mm width and 0.50 mm thick and having equal flanges of 32 mm. The floor and ceiling channels are fixed to floor and soffit using fasteners at every 600mm c/c. A horizontal frame section is placed at every 600 or 1200mm c/c .The Rockwool of thickness 50mm and density 48Kg/m3 is fixed in between the studs enact with chicken mess . On outer side one layer of 9mm perforated water proof plywood or MDF board is screwed .These boards are joined using “type S” Self tapping SS W 25 / 3.5 x 25mm corrosion resistant drywall steel screws spaced at 200mm centres on all joints and 300mm centres in the field of boards. Screw fixing is done mechanically. These boards are perforated on site or CNC ensuring min. 50% area is perforated. Finally 9mm thick Polyester fiber acoustic panels are pasted on top of MDF board (using any acrylic adhesive such as fevicol SR998 or hot melt adhesive) of the board as per design of the architect. The entire system should eco-friendly, 100% recyclable & toxic free. ( Note: Existing Frame for Wall panel is to be used after adjusting it according to profile of wall panel)

Providing and fixing grooved panel having system NRC up to 0.75 with lineal perforation. The panels shall be fire resistance (FR) BS476 Part 7 with melamine laminate panels having density of 800kg/m3 (base panel confirming to IS 12406 and laminated panel confirming to IS 14587). The black of the panels are perforated with a nonwoven fabric covering of 0.2mm for providing Sound absorption via the acoustic impedance method. Panel is fixed by using GI Framework spaced at 600mm centers @ aluminum framework spaced at 400mm centers with suitable brackets and the system is backline with 50 mm Roxul Rockwool and along with all accessories. Screw the aluminium extruded keel for channelled woodworks provided over the lowest and second wooden batten at an on-centre distance of 600mm. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer-in-Charge and insert the end of the panel in the skirting. Finish off the edges using wooden moulding of matching colour. Installation to be carried out by Trained Installation team & amp; Installation should be carried out as per recommended procedure. MAKE Topkaustik, Wood Fit, Armstrong, VEILS ( Note: Existing Frame for Wall panel is to be used after adjusting it according to profile of wall panel)

DOOR AND WINDOW

Providing & fixing Acoustical sound reducing Doorsmade with 2nd class Teak Wood framework, infill in 96 kg/ cum density resin bonded glass wool with 6mm commercial water proof ply and 4mm thick veneer on both sides. Anechoic barrier designed to achieve SHIELDING EFFECTIVENESS 25-35 dB..It should be provided with 300x300 double glazed vision window. The door to be attached with the door frame by SS ball bearing hinges with adequate strength and numbers to avoid sagging All joints to be sealed with Dow Corning 790 or equivalent mastic Sealant. Cost should include Door Handles, hinges, Long Tower bolts, Sliding Door bolts with Door Closures till 100Kg weight Capacity Stainless Steel Accesories should be used. The Work shall be executed as per drawings, Specifications & Instruction of engineer in charge. Properties: » Doors are supplied complete with their own mounting frames » Adjustable Soundproof Jambs & Seals » Infill Material : Insulation wool » Best Performance Wood Finished Door Assembly » Heavy Duty Hinges (4) » 3-Point Latching System Hard ware make Marshall/Assa Abloy/Dorma/Haffele teak wood seasoned vineer : Greenlam , Century

1000 x 2100 (SINGLE DOOR)

2000x 2100 (DOUBLE DOOR)

Providing & fixing of the chowkhats for the acoustic doors out of teakwood of size 175x 100 mm . MAKE: Action Tesa, Hara Design (fire rating 2 hrs)

Providing and fixing 450 mm brushed steel finish D shape handles as approved by consultant / engineer in charge.

Supply & fixing of 304 grade stainless steel ball bearing hinges from Marshall/Assa Abloy/Dorma/Haffele of size 100x100x3mm thick complete as per direction of Engineer-in-charge.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock, Exit device on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

FLOORING

Providing & fixing of the 6mm underlay in gangways and aisles after cleaning & rectification of the floor by filling white cement & POP mix .

Providing & laying carpet tile with following specification: Style: Tile Roll, Construction : Tufted Textured Loop Fiber Product: 100% Solution Dye PP, Gauge: 39.4/10cm. (1/12), Finish Pile Thickness: 7.49mm +/- 0.5, Production yarn weight: 20 oz, Dye Method: 100% solution Dyed, Primary backing: Action Back, Tuft Bind: As per ASTM Standards, Delamination Strength: As per ASTM Standards, Static Control: As per ASTM Standards, Soil retardant: Protek, Anti-Microbial: Alphasan Built in Protection, Moisture Control: Yes, Electrostatic propensity: less than 3.5KV-Permanent Cond, Flammability( Radient Panel ASTM-E-662): >_0.45 ( Class I) Make: Brintons, Deck O Floor. Alfa Carpeting Co. Pvt. Ltd.

Providing and fixing proprietary Anodized Aluminum Skirting of 100mm high, as per details and approval of Engineer-in-Charge MAKE: Indal, Mahaver,Hindalco, Jindal

Providing and fixing the Aluminium L shape trim to be of 32 mm in width at the edge of steps to prevent wear and tear of carpet from the edge . The trim to have brushed finish as per approved sample. MAKE: Indal, Mahaver,Hindalco, Jindal

Description of Work / Item(s)

Amount

Supply of 8.5TR actual capacity based on Noida climatic condition DX outdoor air cooled condensing unit complete in all respect inclduing scroll compressor, green refrigerant gas etc., & required valves. Note: Fins and copper tubes of Air Cooled Condenser along with copper tubing / piping with all joints and U-Bends exposed to coastal areas corrosive atmosphere / aggressive ambient, shall be painted with special corrosion prevention coating either in factory or at site. R-410a refrigerant shall be provided. DX Coil:- 6 row deep intertwined DX cooling coils with Copper tubes and Aluminium fins 12-13 fin./inch.

8.5 TR Condenser Unit with scroll compressor

Make: HITACHI/ Daikin/ Bluestar

Installation of airconditioning system of following items

Providing & fixing MS frame work for above out door units . The frame work shall be fabricated out of 50 x 50 x 6 mm thick angle iron and dully powder coated. Design of frame work shall have to be approved by site engineer/ consultant. Two layers of 100 x 100 and 6 mm thick vibration isolated shall be required below each supporting legs. MAKE: Tata, Jindal, Prakash Surya

Supply, Installation, testing and commissioning of the insulated refrigerant piping for all the units. The insulation shall be with 13 mm thick nitrile rubber make through out the running length of the refrigerant piping. The piping shall be well supported at specifications. (Make: Mandev/ Maxflow/ Rajco/ Ryku)

Copper pipe for 8.5 TR Unit (9/8" & 1/2")

Supply, installation, tesing and commissioning of Drier & Expansion Valve Make: Danfos or equivelent

Cable Tray

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. MAKE: Dexion, Pilco, Soltco, Ricco

300 mm width X 50 mm depth X 1.6 mm thickness with cover

150 mm width X 50 mm depth X 1.6 mm thickness with cover

Providing and fixing in position rigid uPVC pipe(min. 20 kg/ sqmt.) complete with fittings, condensated drain pipe duly insulated with 6 mm thick closed cell nitrile rubber insulation as per specification and standards . Piping shall be properly supported with MS hanger . Make: PRINCE/ SETIA/ POLYPAC

50 mm dia

Control Cables : supplly and laying, of the following 1100 volts grade PVC insulated sheathed copper conductor a moured cables on cable trays Gl Earthing, clamped to wall with suitable clamps, saddles and fixing bolts as per specifications , inculding termination, testing and commissioning. contractor should check cable size based on motor reting. Make : - slytone, gloster, universal

2 Core x 1.5 sqm

Civil work wall cutting/chessing

Air- Distribution Work

Ducting

Supply, fabrication, installation and testing of G.S.S. sheet metal ducting complete with vanes etc. as required & as per approved shop drawings.G.I. Sheet Metal Ducting (Rectangular) SITE Fabricated Make: Jindal/ Sail/Tata

24 Gauge

22 Gauge

20 Gauge

Grilles/Diffusers

Supply, Installation and Testing of return air grilles/ diffusers as per specifications and drawings.Make: System Air/ Pine Air/ Mapro/ Balance Air/ Conaire

Aluminium supply/ Return air grill without damper

Repaint of existing Grilles

Providing and fixing of Volume Control Dampers to be provided in supply air registers / terminals. Make: System Air/ Pine Air/ Mapro/ Balance Air/ Conaire

Providing and fixing fire retardant nonporous double layer flexible connection between each unit and duct. (AHU) Make: A FLEX/ K Flex/ Superlon

Supply & installation of duct insulation with 9mm thick close cell nitrile rubber. Make: A FLEX/ K Flex/Superlon

Providing and fixing of Duct acoustic lining with glass wool insulation, coverd with perforated aluminium 26 Ga, sheet, nuts, bolts etc.complete with all accessory as required. Make: UP twiga/ Owens corning

25 mm thick and 24 Kg density

AHU & Panel Works

Supply, Installation, Testing and commissioning of factory built floor mounted DX based double skin Air Handling Units made of 43mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8mm inside layer with polyurethane foam (PUF) insulation having density of 38kg/m3 factory injected between them by injection moulding machine, complete with thermal break profile, complete with DIDW backward curve SA blower section with blower (AMCA Certified) suitable for 65 mm External static pressure as required, minimum 2 bend GSS/PVC eliminators, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.4 mm) cooling coil of minimum 6 rows deep, complete with prefilter and electronic air cleaner filter (equivalent to MERV-13 filter), Mixng Box section, fresh air damper and return air damper, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% V, 50Hz, 3 Phase AC supply suitably designed for VFD applications, drain connections, stainless steel (18G) drain pan with nitrile rubber/PUF insulation, necessary vibration isolation arrangement, gravity louver, fire retardant canvas connection inside AHU & for duct connection complete with metallic flange & rubber gasket complete as per specification and of following capacities. Suitable capacity of VFD (min. IP-65) with TPN isolator within M.S enclosure box complete as required and as per specifications

10500 cfm/ 65 mm External Static

Supply Installation testting & commissioning of starter panel for Airhadling unit with all necssary Controling System. MAKE: Advance panels & switch gears, tricolite, associated switch gear & projects, Adlec System, Milestone, SPC Electrotech, Ambit, Risha

Dismentalling of AHU work

Dismentalling of already dismantled AHU unit except ducting/ grilles, diffuser all related to HVAC work. (The AHU has already been dismantled except ducting portion)

Ventilation system of following items for Auditorium Fire System

Air- Distribution Work

Ducting

Supply, fabrication, installation and testing of G.S.S. sheet metal ducting complete with vanes etc. as required & as per approved shop drawings.G.I. Sheet Metal Ducting (Rectangular) SITE Fabricated. Make: Jindal/ Sail/Tata

24 Gauge

22 Gauge

Providing and fixing fire retardant nonporous double layer flexible connection between each unit and duct. (FOR INLINE FAN)

Providing and fixing fire retardant nonporous double layer flexible connection between each unit and duct. (FOR TUBE AXIAL FAN)

Supply, Installation, Testing of UL Listed Motorized Fire Damper as per approved shop drawings and specifications. Make: System Air/ Pine Air/ Mapro/ Balance Air/ Conaire

Supply, Installation, Testing and Balancing of UL Listed Actuator with Control wiring for above Motorized Fire Damper as per approved shop drawings and specifications. Make: System Air/ Pine Air/ Mapro/ Balance Air/ Conaire

Supply, Installation, Testing and louver with bird screen for fresh air exhaust.

Ventilation, AHU & Panel Works

Supply Installation testing & commissioning of Inline fan for exhaust and fresh air as per below detail.Make: Balance Air/ Air flow/ Carryair/ Flackwood/ Merathan/ Systemair

Toilet Exhaust 500 cfm

Supply Installation testing & commissioning of Axial flow unit for exhaust and fresh air unit per below detail.

SMOKE FAN FOR EXHAUST -WITH CLASS H MOTOR Make: Balance Air/ Air flow/ Humidin/ Flackwood/ Merathan/ Ravi Aircon

11000 CFM/25MM static

Supply Installation testting & commissioning of starter panel with transformer 24 v Dc supply for fire damper for fan with all necssary Controling System. MAKE: Advance panels & switch gears, tricolite, associated switch gear & projects, Adlec System, Milestone, SPC Electrotech, Ambit, Risha

Civil Work for Fan installtion part

Description of Work / Item(s)

Amount

FIRE and CCTV

SECTION - I- STRUCTURED CABLING SYSTEM PASSIVE

Supply , Installation, Testing and Commissioning of CAT 6 UTP cable 23 AWG solid copper conductors for Connectivity of Hub room to End Point. Approved Makes: Belden/Siemon/Panduit/Der Wiser

Supply , Installation, Testing and Commissioning of CAT6 information outlet (I/O) for camera at user end. Approved Makes: Belden/Siemon/Panduit/Der Wiser

Supply , Installation , Testing and Commissioning of loaded 24 port CAT6 jack panel for CAT6 cable termination at rack end. Approved Makes: Belden/Siemon/Panduit/Der Wiser

Supply , Installation , Testing and Commissioning of CAT6 patch cord 3 feet for rack side switch to jack panel connectivity. Approved Makes: Belden/Siemon/Panduit/Der Wiser

Supply , Installation , Testing and Commissioning of CAT6 patch cord 7 feet for information outlet (I/O) to end user device connectivity. Approved Makes: Belden/Siemon/Panduit/Der Wiser

Supply , Installation , Testing and Commissioning of 1, 2 and 4 port face plate white for I/O fixing at user side. Approved Makes: Belden/Siemon/Panduit/Der Wiser

Supply , Installation , Testing and Commissioning of 15U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts. Approved Makes: Poweride/MTS/Rittal/APC/APW

SUB-HEAD -II- IP CCTV SYSTEM

Supply , Installation , Testing and Commissioning of 3 MP Dome Camera , ONVIF profile S & G ,UL , CE , FCC Certified , 1/2.8" CMOS sensor ,2.8mm to 12 mm motorized varifocal , triple stream ,Min Illumination :0.04 Lux @ (F1.2,AGC ON), 0 lux with IR ,120 dB WDR, Shutter Speed : 1/5 ̴ 1/100,000 s, Video Compression : H.265 , H.264 ,frame rate 25/30 fps @ 3MP ,Edge analytics : line crossing , perimeter intrusion ,Face detection , cross counting , stationary object , Inbuilt IR LED , IR distance upto 30 mtrs ,IK 10 Vandal proof ,IP 66 , POE. Approved Makes :Allgovision/ / Avigilon / Pelco/ Axis/ Impulse

Supply, Installation, Testing & Commissioning of ONVIF profile S & G ,UL certified 16 Channel NVR , 2 SATA ports , each SATA capacity of upto 8 TB , Recording Bandwidth 320 Mbps , 1 X HDMI , 1 X VGA , Alarm : 16ch in / 1ch out , 1 X RJ45 port , 1x3.0 USB for backup / upgrade, 2x 2.0 USB for mouse , Smart Phone support : iOS, Android Approved Makes :Allgovision/ Impulse / Avigilon / Pelco/ Axis

Supply , Installation , Testing and Commissioning of 6TB Surviellance Hard Disk. Approved Makes: WD /segate /Toshiba/HP

Supply , Installation , Testing and Commissioning of Professional Display Panel. 32" LED display, full hd resolution 1920x 1020 , 300 nits brightness including wall bracket for display complete as required Approved Makes: Panasonic / LG/ Sony/ Samsung

Supply , Installation , Testing and Commissioning of Intelligent Ethernet Switch, 24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3—10BASE-T, IEEE 802.3u—100BASE-T IEEE 802.3ab—1000BASE-T ) 4 SFP+ fixed 1000/10000 SFP+ ports, 1 RJ-45 serial console port and one OOB port, Support Throughput minimum 84 Gbps , Should support Zero touch Deployment With India Power Cord . POE Power budget - 400 Watt or more. support Device profiling, automatic port configuration and network segmentation improves security posture of the network. Approved Make : Extreme / Juniper / Arista / Impulse

Supply , Installation , Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest. Approved Makes: HP / DELL / IBM / LENOVO

SUB-HEAD -III- FIRE DETECTION SYSTEM

Supply , Installation , Testing and Commissioning of Addressable Multi-criteria Photo-Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. Designed to meet UL268, 7th Edition. Approved Makes :Ansul / Edwards / Notifier / Wissenschaftler / Rux

Below False Ceiling

Above False Ceiling

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required Approved Makes : Ansul/ Agni/ Edwards/Notifier/Wissenschaftler/Rux

MANUAL CALL POINT

Supply , Installation , Testing and Commissioning of Addressable Manual Call Point (Pull down / Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Approved Makes :Ansul / Edwards / Notifier / Wissenschaftler / Rux

FAULT ISOLATOR

Supply , Installation , Testing and Commissioning of Addressable Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance. Approved Makes :Ansul / Edwards / Notifier / Wissenschaftler / Rux

BEAM DETECTORS

SITC of Addressable analogue Beam detectors suitable for range upto 10-70 meters including transmitter and receiver units, mounting kits , complete as required . Makes :Ansul/Eaton/Siemens/Notifier

CONTROL MODULES

Supply , Installation , Testing and Commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide DPDTcontact rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance. Approved Makes :Ansul / Edwards / Notifier / Wissenschaftler / Rux

Hooter cum strobe

Supply , Installation , Testing and Commissioning of Addressable Sounder cum Strobe rated at 75 dBA @ 3m for Audible annunciation and 75cd flashintg at 1 Hz for visual indication. Approved Makes :Ansul / Edwards / Notifier / Wissenschaftler / Rux

FIRE ALARM CONTROL PANEL

Supply, Installation, Testing and Commissioning of UL 864 (10 EDITION) listed and FM approved microprocessor based 2 wire fault tolerant loop, (each loop accessing minimum 125 detectors and 125 modules ) with Peer to Peer network communication system with additional 20 % Spare capacity in each loop fire alarm/detection and integrated voice evacuation control panel of same make having 8 simultaneous multiplexed audio channels with LCD display min 600 character , graphic software and compatible computer with sufficient panel enclosure and cabinet size to accommodate Integrated voice evacuation unit for automated messaging with suitable Wattage amplifier. The panel must have minimum 1,000 event history storage. The panel shall have control and display switches for 24 speaker zones with one-way and two-way emergency audio communications facility. The panel should be modular snap fit type and should operate on the broadcast polling. The system should have automatic mapping feature. The panel shall be able to give location of all fire/fault conditions of addressable units via the address codes and shall have zone indication display LEDs on the main panel using the mountable LED strips on the panel. Further, the panel must be able to automatically switch ON /OFF respective control module whenever any alarm is triggered. The panel shall have rectifier, Loop cards, L C D unit to indicate Fire/Fault Signal with address and analog output, external/inbuilt printer to log all fire or fault events complete in all respects. The keypad should be rugged and rubberised for emergency operations to be operated by fireman wearing fire gloves. The panel shall have a built in power supply and battery charger which should be able to charge with a upto 260AH along with maintenance free 24 AH, 2 x 12 volt SMF Lead acid batteries capable backup of 24 hours operation and 30 minutes alarm operation complete as required. Panel shall have Bacnet/Modbus card for BMS integration either or on modbus or Bacnet. The system should offer fail safe degraded mode making the life safety system working in any given set of conditions.

01 Loop (each loop consist of 125 detector & 125 devices) Approved Makes :Ansul / Edwards / Notifier / Wissenschaftler / Rux / Bosch

Supply, Installation, Testing and Commissioning of Graphical User Interface of the (same make of the panel) ,complete in all respect as required and as per specifications. The system should be capable of establishing IP connectivity in Graphics software to take multiple system inputs from multiple panels. Highlighting an event in the “Event List Viewport” shall automatically cause the display of the map viewport and other configured viewports to display information relative to the highlighted event.

Supplying and Laying of 2 C X 1.5 Sq mm multi stranded twisted shielded FRLS Copper cable. Approved makes : Polycab/ RR Kabel/ Paramount/ Parasheild

Description of Work / Item(s)

Amount

STAGE FURNISHING

Supply, installation, testing and fixing of MAIN FRONT CURTAIN made out of glazed cotton cloth 450 GSM with linning , 50% gathering biparting , type side movement complete with providing and fixing heavy duty rails, brackets, moterised operation complete with required limitor switches(siemens/bohmen). for end stopper ,gear box, 2 (make rotoman, kirlosker) mini drums, weights, limit swithes, cuplink, runners, master runners,pullies, 3mm steel rope wire, 2HP motor (Crompton/ kirlosker). 2 nos air breaker contactors (L&t/Siemens). Push buttton for stop, . Motor mounting with C channel platform on side wall. Curtain cloth should be fire retarhdant. Basic rate of cloth will be Rs. 900 per meter (size of curtain- 9000 mmX5000 mm) MAKE: Reliance, Nexgen, Comrade

Supply, installation, testing and fixing of REAR CURTAIN made out of glazed cotton cloth 350 GSM with horizontal sliding arrangement complete with fixing rails, brackets, moterised opration complete with gear box, runners, master runners,pullies, 3mm steel rope wire, 1HP motor (Crompton). 2 nos air breaker contactors (L&t/Siemens). Push buttton for stop, forward and reverse and close positions. minimum overlap at centre 900mm. The curtain stitched in double gathering.Curtain cloth should be fire retarhdant.Basic rate of cloth will be Rs. 500 per meter (size of curtain- 9000X5000) MAKE: Reliance, Nexgen, Comrade

Supply, installation, testing and fixing of Stage frills to be installed above the stage on 28mm dia GI pipe adjustable at position according to stage positioning plan. Cloth material of desired shade with Stitching.Cloth should be fire retarhdant. MAKE: National Handloom, Nexgen, Comrade, Response

for front frill Basic rate of cloth will be 600 per meter

for back frill Basic rate of cloth will be 500 per meter

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. MAKE: Dexion, Pilco, Slotco, Ricco

100 mm width X 50 mm depth X 1.6 mm thickness

Supply, Installation, Testing and commissioning of Rotatable Side wings attached with ceiling grid and floor. Base frame to be made with 50mm x 25 mm x 3mm rectangular hollow MS pipe of grid size 600 x 600 mm duly painted with 1 coat of Red Oxide and 2 coats enamel paint. MS Grid to be filled with rockwool of density 48 kg/cum insulation inside and covered with 6mm thick perforated ply both side of the wings over which stretched fabric black in colour to be applied. Cloth of fabric should be fire rated with 350 gsm. basic rate of fabric will be 500 rs/ meter MAKE: National Handloom, Nexgen, Comrade, Response

The proscenium of a stage to be fabricated on site made with 38x38 x 3mm MS square hollow pipe of grid size 600 x 600 mm duly painted with 1 coat of Red Oxide and 2 coats enamel paint. Infill in 50mm thick Rock wool of density 48 kg/cum insulation padding.panell to be covered with 12mm Water Proof Ply on both side of the Procesium. Finishing with . Fixing with Polyester fiber acoustic mat finish panel 9mm thick @ 200kg/m3 density with Class A fire rating as per ASTM E 84 & thermal conductivity 0.034w/mk with desired acoustic management 0.80 NRC as per design by architect (2 vertical members- 2000X5000, 1 horizontal member- 12500X900)

Grid Structure Customized Fabrication of Main Overhead Grid over Stage using 40mm x 40mm x 5mm MS A Iron, in a 600 mm x 600 mm panel size. Section & suspended from the ceiling.Provides mounting positions for equipment and access to any point over the stage for rigging and maintenance. use as a foundation for curtians, light bar and frills structure mechanism MAKE: Tata, Jindal, Prakash Surya

Supply, Installation, Testing and commissioning of Side Ladder Made with 50x25mm size rectangular hollow MS pipe duly painted with 2 coats enamel paint for a stage side light Suitable for fixing 3 nos of lights. Used for provide cross lighting from the both sides to the performer or object. MAKE: Tata, Jindal, Prakash Surya

Stage Lighting Truss Bar Over Head Light Bar 40 od dia pipe of full length trussing with adequate clamps with black quick drying enamel paint to mounting for stage lighting, which is suspended from bars above the stage MAKE: Tata, Jindal, Prakash Surya

FOS “FRONT OF STAGE” LIGHT BAR 40 od dia pipe of full length trussing with adequate clamps, coated with black quick drying enamel paint required which is suspended from ceiling in front of stage MAKE: Tata, Jindal, Prakash Surya

STAGE LIGHTING

Supply, Installation, Testing & Commissioning of Wiring for DIMMABLE Points: Using PVC Insulated Finolex 2.5 sqmm 3-Core FRLS Cu. Cond. Cable for each socket ; starting from the Dimmer Rack to the Lighting bars/tree or stage points terminated at junction box with 1 or 2 x CEE 16 Amp. Sockets (all boxes to be mounted on Light Bars & all points to be marked & numbered) MAKE: Finolex, Havells, Polycab

Supply, Installation, Testing & Commissioning of Wiring for Direct Points Using PVC Insulated Finolex 1.5 sqmm 3Core FRLS Cu.Cond. cable for 2 sockets/box. cable for 2 sockets/box ; starting from the supplied MCB Box/Panel, having 10A SP MCBs, to the Lighting bars/tree or stage points ; terminated at junction box with 2 x SHUCKO 16 Amp. Sockets/per point (all points to be marked & numbered) MAKE: Finolex, Havells, Polycab

Supply, Installation, Laying, Testing & Commissioning of DMX Data Signal Point Wiring : Using 2-core PVC insulated 22AWG multi-stranded Cu.Cond. high speed data cable designed for EIA485 ; low capacitance, twisted pair shielded ; FHDPE insulation - starting from DMX Splitter to each Light Bar - either sides, Side Ladders and Floor Points, as required to be terminated with suitable XLR connectors MAKE: Falcon, Belden, Krystal

LIGHT FIXTURE

543W 3-in-1 LED PAR Aluminum Dye Cast Power supply: AC110V-250V Frequency: 50-60Hz Power Consumption: 120W Light Source: 36PCS 3W 3 in 1 LED Lamp Life: 6-10 ten thousand hrs. Refraction surface: Frosted LED Angle: 30(± 5) degree 45° , 60°Colour Temperature: 5600K MAKE: Effectron, Modern Stage Service, Canara lighting

250Watt COB LED Light Input Voltage(V):AC100-240V, 50/60Hz Working Lifetime(Hour): 60000 Beam angle: 38 degree Channel: 7Channels StrobeL1-20 times/ second Dimmer: 0-100 percent Connector:3-PinXLR (In and Out) Cooling System: Natural convection heat transfer MAKE: Effectron, Modern Stage Service, Canara lighting

750W Halogen Profile Spot 19 Degree Code : Providing and fixing of 750w of profile halogen spotlight with 150,,Die Cast Body diameter plano convex lens, 750W bi-pin halogen lamp, 240V, Aluminium Ellipsoidal anodized spherical reflector, CRC sheet metal body with matt black powder coat finish, complete with lamp, GI Hook clamp suitable for 50mm bar, 1 m long 2.0 sq.mm 3 core copper flexible cable with 3 pin 15 Amp plug top complete as required Approved MAKE: Effectron, Modern Stage Service, Canara lighting

400W LED Follow Spot Light Code : LK FLW 400 450W LED Follow Spot Light with daylight 450W COB 6500K White LED source having 5 Colors inbuilt, fader based intensity control, dimming and irish effects.Channel DmX Control, Manual Control Panel - Faders, IP20 Rating of Protection with Aluminium Die casted Body. MAKE: Effectron, Modern Stage Service, Canara lighting

CYCLORAMA Light : using 8 Nos.x 150w Hi-Power 4-in-1 'COB' LEDs, with a wide & even beam-angle of 80 degrees ; fully DMX-512 control with Smooth 0-100% linear Dimmer ; DMX 6/10 Ch. controls ; MS sheet housing ; IP-20 rated ; Power AC 100-260V/50Hz 330W ; with Power on mains connectors ; to be supplied with suitable C-clamp & Safety wire. MAKE: Effectron, Modern Stage Service, Canara lighting

4 EYES NON‐WATERPROOF COB BLINDER LIGHT Power input: 90- 245V050 - 60Hz Power: 450W Light Bead control: single point control Colour temperature: 3200K - 6500K Dimming: 0 - 100% linear dimming IP: IP20 Size: 420* 120 * 490mm weight:7.5KG. MAKE: Effectron, Modern Stage Service, Canara lighting

DMX Controller 48 Channels: DMX Controller 48 Channels Providing and fixing of wall mounted dimmer panel with patch panel capacity of 12 channel , 4 kw each channel total capacity of 48 kw totally compact DMX control and MCBs for each channel input of rated capacity protection with 3 phase and neutral bus bar, each channel indication lamps complete as required . DMX 512 MAKE: Codem Music, PLS, Light Sky, SHOWTEC, CANARA, MODERN STAGE SERVICE

Light controller DMX spliter 8C: DMX splitter is a DMX512 distribution amplifier it is specially designed for connection of DMX receiver (dimmers, color changers, move lights, etc) in a star configuration. DMX splitter can surmount the restriction that single RS485 can only connect 32 sets of equipment The multiple output optically isolated DMX512 distribution amplifier have become necessary in many DMX512 system. DMX splitter provide total electrical ground isolation between different branches of the stars. this greatly decreases problem with ground loops. MAKE: Codem Music, PLS, Light Sky, SHOWTEC, CANARA, MODERN STAGE SERVICE

Providing and fixing of Universal lighting DMX control desk, 240 Intelligent Fixtures + 240,Dimmer Channels; 1024 Channels; Load and Save shows with USB; Theatrical Plotting & Playback controlling 450 memories, chases or cue lists MIDI

Providing and fixing of pilot 2000 lighting console for intelligent lighting control

Black Steel Hook: G Clamp - Truss and Stage Lights

Description of Work / Item(s)

Amount

FURNITURE

Providing, supplying and installating Desk and chair. The Desk shall be made up of 25mm thick marin ply board (make geenply, century, bhutan tuff) , with approved laminate and shade. The profile shall be in curved shape in accordence adjusant desk and drawing given by Engineer-in-charage. The edges shall be sealed with 2mm thick strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The front shall be clad with modesty panel of 18mm thick marine ply with both side laminate duly edge banded. The top shall be supported on MS pipe frame having cross-section area 40 x 20 x 1.5 mm thick. The modesty shall be arrested together with MS rectangle pipe frame having cross-section area 50X25X2.18mm thick. The understructure shall have 2 nos. of legs made up of MS capsule pipe having cross-section area 80X40X2.5mm. The side shall have corner plate made up of 2mm thick CRCA sheet of grade 'D'. It should be supplied with 1 nos. of chair. Desk height- 750mm And Top Size- 1500mm (W) X 400mm (D) x 25mm thick for two seater. Desk will be in housed with the provision of led light at front refecting modesty in the cove. it shoud have provision for power socket and switch with goose neck mike The metal frame and sheet shall be electrostatically coated with epoxy powder with 40-60µ thick., INSTALLATION The Desk should be individually grouted to the floor by expandable fasteners in single frame or could be on common frame with the assistance of 10mm thick HR steel plate. The size shall have upper and lower deviation up to ±10mm. Supply installation and commissioning of CHAIR( Fixed based rotation chair) The seat and back shall be made up of 18mm and 12mm thick hot pressed commercial plywood respectively and padded with high resilience polyurethane foam for seat and back is moulded with density = 45+/-2Kgs/cu.m. and hardness= 20 +/-2 on Hampden machine at 25% compression.. The same shall be upholstered with fabric tapestry. The seat shall be arrested together with rectangle pipe frame having cross-section area 30X15X1.6mm thick. The understructure shall consist of MS round pipe having dia. 115mm with 2mm thick. The base plate shall be made of 6mm thick HR steel for grouting. Seat Height - 450mm, Seat Size - 460mm(W) x 500mm(D), Back Size - 460mm(W) x 400mm(H),. The armrest is made up of integral polyurethane foam and reinforced with M.S insert. MAKE: Steelcase, Veils, Geeken, Herman Miller CHAIR ( fixed bace rotation chair) The seat and back shall be made up of 18mm and 12mm thick hot pressed commercial plywood respectively and padded with high resilience polyurethane foam for seat and back is moulded with density = 50+/-2Kgs/cu.m. and hardness cusion 120 = +30 +/-2 back rest 80(=30/-10on Hampden machine at 25% compression. The same shall be upholstered with fabric tapestry exactly as approved by IAHE. The seat shall be arrested together with rectangle pipe frame having cross-section area 30X15X1.6mm thick. The understructure shall consist of MS round pipe having dia. 115mm with 2mm thick. The base plate shall be made of 6mm thick HR steel for grouting. Seat Height - 450mm, Seat Size - 460mm(W) x 500mm(D), Back Size - 460mm(W) x 500mm(H),. The armrest is made up of integral polyurethane foam and reinforced with M.S insert. INSTALLATION The Desk should be individually grouted to the floor by expandable fasteners in single frame or could be on common frame with the assistance of 10mm thick HR steel plate. The size shall have upper and lower deviation up to ±10mm. The metal frame shall be electrostatically coated with epoxy powder with 40-60µ thick. MAKE: Steelcase, Veils, Geeken, Herman Miller

Description of Work / Item(s)

Amount

AUDIO-VIDEO SYSTEM

Active line array : System Type 2-way full range, Active Array Element ; AMP Power : 800W Continuous, Bi-AMP (Class D-650W LF, Class AB- 150W HF), 1600W Program/ 3200W Peak ; Speaker : 2 x 1" Neodymium Compression Driver, 1.75" Voice Coil, 2 x 8" Neodymium MID Woofer, Water Resistant Coating,With Wave guide ; Frequency Response (±3dB) 70 Hz - 19 kHz ; MAX SPL@ 1m 127 dB (peak) ; Crossover (MID-High) 1.8kHz ; Dispersion (-6dB) 110° Horizontal / 10° Vertical

Audio Focus /Honeywell / DB Technologies

Speaker Brackets : For Hanging arrangement of Speaker

Supply installation testing & commissioning of active Subwoofer : system type active subwoofer ; Power Rating 2000W (PROGRAM)/ 4000W (PEAK) or better ; Transducer Low 18" Woofer or better , 3" Sandwich Voice Coil with long excursion or better ; MaxSPL 134dB Max or better ; Active Crossover BandPass type 12dB/oct. under analog processor ; Frequency Response (-6dB) Under analog processor ; 40Hz - 120Hz or better

Audio Focus /Honeywell / DB Technologies

Active stage monitor : System Type 2-Way Active Monitor with DSP ; Transducer Low 12” Woofer, 3" Voice Coil ; Transducer Driver 1" Compression Driver, 1.75" Voice Coil ; Nominal Coverage (HV) 60° X 40° (-6dB) ; Frequency Response 60Hz - 20KHz (-6dB) ; Crossover Frequency At 1.5KHz with 24dB filter slope, Linkwitz-Riley Type ; Max SPL 128dB Max ; Power Rating 1600W (PROGRAM) - 3200W (PEAK) ; Input Connector Line/Mic - Combo/Link - XLR ; Line Input Combo Connector OdBu ; DSP Presets VOCALI / FLAT/ VOCAL2

Audio Focus /Honeywell / DB Technologies

Mixer : On-board processors SPX algorithm: 24 programs, PARAMETER control:1, FOOT SW:1 (FX RTN CH on/off) ; Phantom power +48 V ; Digital I/O USB Audio Class 2.0 compliant, Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit ; Mono[MIC/LINE] 8 ; Mono/Stereo[MIC/LINE] 2 ; Stereo[LINE] 2 ; STEREO OUT 2 ; MONITOR OUT 1 ; Bus Stereo: 1, GROUP: 4, AUX: 4 (incl. FX)

Yamaha/Allen & Heath/Sound Craft

Wired Vocal Microphone , Transducer type Dynamic Polar pattern Super cardioid Frequency response: 30 - 18,000 Hz Nominal impedance 600 Ω Connection 3-pin XLR male

Sennheiser/Shure/Beyerdynamic

Instrument Microphone with high-frequency reproduction ; Polar Pattern: Cardioid, Frequency response : 50-17,000 Hz ; Open circuit voltage : 2.4 mV/Pa, Nominal impedance : 600 Ω, Load impedance : ≥ 2 kΩ, Connection : 3-pin XLR tc. complete with installation as per the site requirement.

Sennheiser/Shure/Beyerdynamic

Sennheiser/Shure/Beyerdynamic

Wireless Lapel microphone, with True diversity receiver receiver (UHF),12 Channel Preset , Display on Transmitter and Receiver , RF Power output 50mW , Polar Pattern :- Omnidirectional , Carrier frequency range 500Mhz to 865Mhz , Frequency response 20Hz to 20Khz , Mute Button on Transmitter , Battery Operation time Minimum 8hr , Should have Charging Contact in Body pack Transmitter . Receiver dynamic range 80dB (A-weighted) switching bandwidth Minimum 30Mhz

Sennheiser/Shure/Beyerdynamic

Condenser gooseneck microphone , Length :- 500mm or better , Frequency range :- 30Hz to 20Khz , Type :- Condenser , Polar pattern Cardioid , Nominal impedance 200 Ω

Sennheiser/Shure/Beyerdynamic

Input Source : CD Cum USB Player

Sony/Samsung/Philips

Floor Boxes : Container for electrical connections, usually intended to conceal them from sight and deter tampering.

Microphone stand (big) : Long Stands for microphone

Softline/GS/Hercules

Microphone Cable : Cable with thickness of 2 Core shielded cable

Krystal/Klotz/Beldon

i. XLR Male

Neutrik/Seetronic/Amphenol

ii. XLR Female

Neutrik/Seetronic/Amphenol

iii. RCA Connector

Neutrik/Seetronic/Amphenol

iv. EP Connector

Neutrik/Seetronic/Amphenol

v. Power Cable

Neutrik/Seetronic/Amphenol

vi. VGA Cable

Neutrik/Seetronic/Amphenol

vii. RCA to EP Cable

Neutrik/Seetronic/Amphenol

Rack: Equipment Rack for housing all rack mountable equipments with internal wiring, front glass door; heat dessipation fans; movement wheels, power distribution units , placed in a rack is typically described as rack-mount, rack-mount instrument, a rack-mounted system, a rack-mount chassis, subrack, rack-mountable, or occasionally simply shelf , Sidewalls, Split rear doors , Baying Kits, toolless Shelves, casters, Bolt Down Kits, Cable Management , Power Strips – vertical or Rackmount, Enclosure Monitoring System , Toolless Blanking Panels, Fans

Supply, installation, testing & comissioning of 4000-5000 ANSI Lumen Projector - 3 LCD, 1200 x 800 WXGA resolution, Aspect ratio : 16 : 9 , 3000: 1 contrast ratio, 245UHP lamp, Motorized zoom, focus & lens shift, picture by picture.

Christie/Planar /Panasonic

4k Display Size- 65", Brightness- 500 nits, Native Contrast Ratio- 5000:1, Haze- 44%, Operating Hour- 24/7, Input- DVI-D, Display Port 1.2 (1), HDMI 2.0 (2), USB 2.0 x 2,Processor-Coretex A72 1.7GHz Quad-Core CPU,Storage (FDM)- 8GB (3.88GB Occupied by O/S, 4.12GB Available), Certification- BIS,EMC Class A, Safety 60950-1 with hanging customised kit

Samsung/Sony/LG

Cyclorama Screen in Plastic Perforated Material. The screen to be fixed on tubular frame made out of 40mm dia MS pipe and Cross MS Pipe 25mm dia; Size:- 13.6 m x 6.4 m MAKE: Galalite, Eurolite, Best Vision

Presentation point with 1 x HDMI, 1 x VGA, 1 x Audio, 2 x Power, 1 x data, 1 x LAN at Stage for connecting laptop on Stage / Podium.(Make / Model : Custom)

Switcher with 4 HDMI inputs , 2 VGA inputs, 2 composite and 2 component Video inputs, single ouptput : 1 x HDMI, 1 X VGA, Control − RS−232 & IR(Make / Model : Kramer VP-438)

20 Mtrs HDMI to HDMI cable in existing conduit

5 Mtrs HDMI to HDMI Patch Cord

10 Mtrs HDMI to HDMI cable in existing conduit

20 Mtrs VGA Cable with audio cable in existing conduit

3 core 1.5 sqmm Power cable

Projector Mount Kit

Description of Work / Item(s)

Amount

ELECTRICAL WORK ITEM

SUB HEAD - I :- POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single Core cable etc. as required.

Wiring for group controlled (looped) light point / fan point / exhaust fan point/ call bell point (without independent switch etc.) with1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, and earthing the point with 1.5 sq. FRLS PVC insulated copper conductor single core cable etc. as required.-group-C

Wiring for power plug with 4X2.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 2.5 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit / submain alongwith earth wiring with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed in suitable size of medium class PVC conduit as required.

2 x 2.5 sq.mm + 1 x 2.5 sqmm earth wire

4 x 2.5 sq.mm + 2 x 2.5 sqmm earth wire

2 x 6 sq.mm + 2 x 2.5 sqmm earth wire for Em. light DB

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2Nos. 3 pin 5/6 amps modular socket outlet and 2Nos.5/6 amps modular switch, connection etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection, painting etc. as required

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. (for Circuit, Telephone & LAN )

Supplying and Fixing following sizes / modules , GI box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (75 mm X 75 mm) For Switch, Telephone, TV and LAN

SUB HEAD - II : SUPPLY AND INSTALLATION OF FAN & LIGHT FITTING

Supply and Installation, connecting, testing and commissioning & Receiving of recessed mounting type Led light fixture, LED of 1 to 3 W Nos. assembled on single MCPCB, having color temp 6500K & having 50000 burning hrs life with minimum @ L70, system lumen output should be minimum with efficacy> 80lm/W. LED driver, PF 0.95 & THD <20%. The colour rendering index of LED light should be more than 70. Housing made of CRCA with glare free diffused polycarbonate cover. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106 from NABL approved Lab. Manufacturer manadatory i/c connection wire, testing etc. to complete the job. 2 Yrs Guarantee certificate from manufacturer. MAKE: Philips, Crompton, Wipro, Surya Polycab, Halonix, Bajaj, Havells, C&S

1x5 W Led Foot light

1x9 W Led down light

1x10 W Led down light

1x12 W Led down light

1x120 W Flood light

5w/mtr Led Strip light

SUB HEAD - III : DISTRIBUTION BOARD

Supplying and fixing following way SP&N sheet steel, MCB distribution board of steel sheet for 240 volts on surface/recess complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB/RCCB/Isolator).

12 way, Double door

Supplying and fixing following way, horizental type three pole and neutral, pre-wired, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with loose wire box, terminal blocks, duly prewired with suitable size FRLS PVC insulated copper conductor upto terminal blocks, tinned copper busbar, neutral link, earth bar , din bar, detachable gland plate, interconnections, phophatized and powder painted including earthing etc. as required. (but without MCB/RCCB/Isolator)

8 way (4+24), Double door

Supplying and fixing 5 amps to 32 amps rating, 240 / 415 volts, 'C' curve, miniature circuit breaker suitable for inuctive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole MCB

25Amp DP MCB

Supplying and fixing following rating, 4P, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 Amps.10 KA (C Curve) 4P MCB

63 Amps.10 KA (C Curve) 4P MCB

Supplying and fixing following rating, DP, 240 volts, RCCB having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

25 Amps. DP

Supplying and fixing following rating, DP, 240 volts, RCCB having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 Amps. DP

63 Amps. DP

Supplying and fixing Cable End Box (loose wire box) suitable for following SP&N sheet steel, MCB distribution board of steel sheet 240 volts on surface/recess complete with connections, testing and commissioning etc. as required.

For 12 way, Double door SPN MCBDB

Supplying and fixing Cable End Box (loose wire box) suitable for following 4P sheet steel, MCB distribution board of steel sheet 415 volts on surface/recess complete with connections, testing and commissioning etc. as required.

For 8 way (4+24), Double door TPN MCBDB

Supplying and fixing of following ways surface/ recess mounting, Double door , vertical type, 415 V, TPN MCB , distribution board with MCCB incomer of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

8 way (4 + 24), Double door

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.(for Vertical DB)

125 A, 16kA, FPMCCB

Description of Work / Item(s)

Amount

TOILET CUBICLE

SUBHEAD-I : SANITARY FIXTURES & FITTINGS:

Providing and fixing Toilet cubicle(of following standard dimension which includes 600mm door size width) made up of thermosetting resign treated high pressure ,self supporting decorative compact laminates with permanently incorporate anti-bacterial agents(under JIS Z2801:2000 certification) during manufacturing .Compact board should be resistance to water immersion through permissible increase on thickness and mass <0.60% and board density >1.35kg/cm3 and fulfilled the criteria of greenguard gold certification and manufactured under EN438-2&3:2005 standard. 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant ,Scratch resistant ,Weather and climatic shock resistant. Finish of compact laminates should be suede finish which includes door, pilasters and intermediate panels finished with approved texture/shades as per IS2046 and fulfilled the criteria of fire retardant under BS-476/97 and EN 438-6 with classification of BS1D0 standard. The top supporting system will run above the ceiling to strengthen support the system it will be settled on end walls with M.S "L" angles mid and Pilaster will be fixed with box top support(304 grade) and intermediate panels will attached to the wall with the help of approved SS(grade 304) channels and all required hardware, made up of stainless steel as per manufacturer’s specification.. Door knob, gravity hinges,Thumb turn locksets with occupancy indicators ,coat hooks with door stopper , U channel, top rail with corner connector, adjustable foot/pedestal,Rubber noice deafening tape, screw & wall plugs should be approved under the instruction of Engineer-in-charge. . All screw will of 304 grade in SS with stain finish. All pilasters are supported by SS bottom cladding . The floor with a clearance height upto 110 mm.Finish and colour of Toilet cubicle should be approved under guidance of engineer-in-charge.

Toilet cubicle with standard dimension front 18mm thick with 2400mm(H)x1500(W), door size 600mmx1830mm), partition 12mm thick 1550 mm depth x 1930mm(H)(including gap of 110mm

Toilet cubicle I- shape(front partition)with 18mm thick standard dimension of 2400mm(H)x1500mm (W) which includes 600x1830mm door size or as per drawing.

All aspect specified by the manufacturers , Greenlam sturdo Classique Wings model or equivalent.

Providing, fixing, testing and commisioning of white colour, vitreous China wall mounted type water closet with C.P. bolts, nuts, C.I. chair or other hanging arrangements, 32 mm CP brass type push button flush valve, 32 mm flush bend, bakelite seat cover with C.P. hinges & rubber buffers, C.P. brass screw, washer with all accessories, including cutting and marking good the walls & floor slab wherever required.wall mounted closet Make: JAQUAR/ Kohler/Toto/Vitra

Providing and fixing concealed cistern with flush plate Make: JAQUAR/ Kohler/Toto/Vitra

Providing and fixing , testing and commissioning of 15 mm dia . Two way CP brass bib cock with hose union and CP wall flange ABS health faucet complete with hook and flexible ss tube minimum length 1.0m as required Make: JAQUAR/ Kohler/Toto/Vitra

Providing, fixing, testing and commisioning of starwhite colour vitreous china below/ over counter wash basin with CP brass waste assembly, wall flanges and rubber adapters for water connection complete Make: JAQUAR/ Kohler/Toto/Vitra

Providing , fixing testing and commissioning of CP brass bottle trap for wash basins and urinals allied Bottle Trap (with Internal Partition) 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange Make: JAQUAR/ Kohler/Toto/Vitra 32 mm dia

Providing and fixing wash basin taps pillar cock self closing system Make: JAQUAR/ Kohler/Toto/Vitra

Providing and fixing Waste coupling 32 mm size full threaded (Jaquar ALD-CHR-705 )/Hindware/ Kohler

Providing and fixing of C.P. brass angle valve with C.P. wall flange, Nut and Washer etc. complete as required. Make: JAQUAR/ Kohler/Toto/Vitra

Providing and fixing of copper connection 450 mm long including nuts and washers and making connection to fixtures and fittings complete as required. Make: JAQUAR/ Kohler/Toto/Vitra

Providing , fixing testing and commissioning of white vitreous china flat back or half stall sensor urinal of size 610 x 410 x 380 mm with fitting, standard size CP brass flush pipe , spreaders with union and clamps ( all in CP brass) with waste fitting and other coupling in Cp brass including painting of fitting and cutting and making good walls floor where ever required

Providing , fixing white glazed vitreous china urinal partition of approved make including rawal plugs, screws ,or any other approved devices for fixing arrangements making holes in a wall , floor and making good ( Division plate)

Providing , fixing aerosol perfume dispenser fixed to all / wall wooden cleats and CP brass screw including cutting and making good the wall where ever required

Providing and fixing 1250 x 600mm beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hardboard ground fixed to wooden cleats with C.P. brass screws and washers for making base for mirror . Mirror to be fixed with silicon pasted on wooden base complete. MAKE: Modi gaurd. Saint Gobain, Atul

Providing and fixing CP brass toilet paper holder Make: JAQUAR/ Kohler/Toto/Vitra

Providing and fixing of CP brass twin coat hook Make: JAQUAR/ Kohler/Toto/Vitra

Providing and fixing of Soap Dispenser with Metallic Bottle liquid soap dispenser complete as required. Make: JAQUAR/ Kohler/Toto/Vitra

SUBHEAD - II : COLD / FLUSHING WATER SUPPLY (INTERNAL / EXTERNAL):

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge. Make: AKG, Finolex, Supreme

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Providing and fixing unplasticised - PVC fittings with all accessories for unplasticised Rigid PVC pipes moulded conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Make: AKG, Finolex, Supreme

110 mm diameter

75 mm diameter

50 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. Make: AKG, Finolex, Supreme

110 mm bend

75 mm bend

50 mm bend

SUBHEAD-III : INTERNAL DRAINAGE (SOIL, WASTE & VENT)

Providing, fixing and jointing sound insulated POLO KAL NG piping system as per ON EN 1415 - part 1-6 & EN 12056 part 1-5 with three layer pipe made of PP/C +PP/MV +PP/C in blue ral 5014 (halogen and calcium free) colour , push / fit type , food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA at a flow rate of 4 ltr per sec and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and Cand DIN 19560, including all junctions bents , clean out plugs etc with all necessary fittings in blue colour fitted with factory , fitted lip ring (POLO PLAST , Germany)

Providing and fixing PP white trap minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections(McAlpine , UK).

110mm inlet and 110mm outlet.

Providing and fixing , testing and commissioning of pipe inlet fittings fabricated with POLO PLAST pipe with maximum # inlets 50,40 and 75 mm OD size POLO PLAST pipe, fixed to P trap including drip seal / pipe seal/ solvent / weld joint / rubber ring joint complete

Providing and fixing floor drain (FD) with 50mm/40mm outlet and one 40mm inlet for waste, with SS grating (adjustable height), having 50mm water seal

Providing and fixing Heavy thick CP brass hinged grating (cockroach trap) with rim of approved design including setting floor with cement mortar to match with floor finish as per requirement

Providing and fixing CP brass grating with frame of approved design including setting in floor with cement mortar to match with floor finish as per Engineer-in-charge requirement.

Size 100mm X 100mm

Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required.

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

G-TECH CONSTRUCTION & FABRICATORS

Intermarc

NEW AGE ACOUSTICS PVT LTD

Decor India

Dovetail Projects Pvt Ltd

SKY CONSTRUCTION COMPANY

APEX HVAC SERVICES PVT LTD

APEX HVAC SERVICES PVT LTD

G-TECH CONSTRUCTION & FABRICATORS

Dovetail Projects Pvt Ltd

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

Decor India

NEW AGE ACOUSTICS PVT LTD

Intermarc

SKY CONSTRUCTION COMPANY

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

G-TECH CONSTRUCTION & FABRICATORS

Intermarc

Dovetail Projects Pvt Ltd

APEX HVAC SERVICES PVT LTD

Decor India

SKY CONSTRUCTION COMPANY

NEW AGE ACOUSTICS PVT LTD

NEW AGE ACOUSTICS PVT LTD

dnv industrial systems pvt ltd

Intermarc

G-TECH CONSTRUCTION & FABRICATORS

APEX HVAC SERVICES PVT LTD

Decor India

SKY CONSTRUCTION COMPANY

Dovetail Projects Pvt Ltd

dnv industrial systems pvt ltd

NEW AGE ACOUSTICS PVT LTD

G-TECH CONSTRUCTION & FABRICATORS

Decor India

Dovetail Projects Pvt Ltd

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

SKY CONSTRUCTION COMPANY

APEX HVAC SERVICES PVT LTD

SKY CONSTRUCTION COMPANY

NEW AGE ACOUSTICS PVT LTD

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

APEX HVAC SERVICES PVT LTD

dnv industrial systems pvt ltd

G-TECH CONSTRUCTION & FABRICATORS

Decor India

Dovetail Projects Pvt Ltd

SKY CONSTRUCTION COMPANY

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

dnv industrial systems pvt ltd

Dovetail Projects Pvt Ltd

Decor India

NEW AGE ACOUSTICS PVT LTD

Intermarc

APEX HVAC SERVICES PVT LTD

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

Decor India

Dovetail Projects Pvt Ltd

NEW AGE ACOUSTICS PVT LTD

SKY CONSTRUCTION COMPANY

G-TECH CONSTRUCTION & FABRICATORS

Intermarc

APEX HVAC SERVICES PVT LTD

dnv industrial systems pvt ltd

G-TECH CONSTRUCTION & FABRICATORS

Decor India

SKY CONSTRUCTION COMPANY

APEX HVAC SERVICES PVT LTD

Dovetail Projects Pvt Ltd

NEW AGE ACOUSTICS PVT LTD

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

G-TECH CONSTRUCTION & FABRICATORS

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

dnv industrial systems pvt ltd

Decor India

Dovetail Projects Pvt Ltd

NEW AGE ACOUSTICS PVT LTD

Intermarc

SKY CONSTRUCTION COMPANY

SAHAI EXCLUSIVE CONTRACST PVT. LTD.

Dovetail Projects Pvt Ltd

dnv industrial systems pvt ltd

Decor India

NEW AGE ACOUSTICS PVT LTD

APEX HVAC SERVICES PVT LTD

SKY CONSTRUCTION COMPANY

Intermarc