8122/SAR-60/2022-23

Amount

Dismantling of boarding any description , fixed in any position with nails complete

Dismantling of wall and ceiling boards including frame ( fibre pulp, insulation etc) or insulation boards/slabs /blankets any thickness including cover fillets complete

Dismantling of wrought iron and mild steel work of any description not otherwise provided complete all as specified and directed by Engr-in-Charge

Dismantling of Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified and directed by Engr-in-Charge

Demolition of cement concrete in reinforced roofs (reinforcement cut as required to facilitate) roof, floor (other than ground floor),beams,, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engr-in-Charge

Demolition of RCC/PCC concrete in ground and paving exc 15cm thickness (below and above ground level and similar suspended work complete all as specified and directed by Engr-in-Charge

Taking down Old CP bib tap complete all as specified and directed by Engr-in-Charge

Taking down Old CP Stop cock complete all as specified and directed by Engr-in-Charge

Taking down Old CP pillar tap complete all as specified and directed by Engr-in-Charge

Taking down Old brass float valve complete all as specified and directed by Engr-in-Charge

Taking down Old waste coupling of PTMT (half or full threaded) minimum weight 32mm 45gms/40gms complete all as specified and directed by Engr-in-Charge

Taking down Old Wash down water closet (Pedestal pattern) compete complete all as specified and directed by Engr-in-Charge

Taking down Old wash basin , vitreous china (flat back or angle back type ) any size , including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed by Engr-in-Charge

Taking down Old sinks kitchen or laboratary with plugs, washer and waste and wastes, including bedding in cement mortar on to dwarf walls or including fixing cantilever brackets and connecting union to waste pipe upto 05 sqm each complete all as specified and directed by Engr-in-Charge

Taking up cast iron 100mm/75 mm dia water mains (including all fittings) with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and directed by Engr-in-Charge

Taking down door closer aluminium extruded section body) complete all as specified and directed by Engr-in-Charge

Taking down tubular towel rail 20mm dia D type 60cm long between flanges complete all as specified and directed by Engr-in-Charge

Dismantling of cast iron or reinforced concrete drain pipes , joited in cement mortar and taking out og trenches, complete all as specified and directed by Engr-in-Charge

Taking down Old flush cistern complete all as specified and directed by Engr-in-Charge

Taking down PVC connection complete all as specified and directed by Engr-in-Charge

Taking down steel rolling shutter push or pull including gear box and connected items complete all as specified and directed by Engr-in-Charge

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified& directed.

M & L brick work sub class 'B' bricks (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work sub class 'B' bricks , (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20 mm gradded stone agg )as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, drain channels, copings,parapets copings, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed.

Demolition of cement concrete (un-renforced) in ground floor and paving. n exc 15cm thickness (below or above ground level.) & removal of rubbish material complete all as specified& directed by Engr-in-Charge.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate), 25mm thick, as in Sub base complete all as specified & directed by Engr-in-Charge.

M&L Non - skid Ceramic colour tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and over 15mm thick screed bed in CM 1:6 complete all as specified& directed by Engr-in-Charge.

Material and labour coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick and area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over screed bed 15mm thick 1:6 cement mortar complete all as specified & directed by Engr-in-Charge.

M&L for Providing and laying prepolished cement concrete Chequered tiles 30cmx30cmx25mm thick, with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape heavy duty , set,jointed and pointed in neat cement slurry in floors over screed bed 15mm thick 1:6 cement mortar complete all as specified& directed by Engr-in-Charge.

M&L for 40mm thick PCC Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in flooring complete all as specified

M&L for Glass dividing strips, 3mm thick, 38mm depth and inserted in position to conform to design complete all as specified & directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:4:8 type D -2 using 40 mm graded stone aggregate as in sub base complete all as specified& directed by Engr-in-Charge.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand compelete all as specified and directed

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in requiredcolour & pattern over and including 25mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; compelete all as specified and directed

Dismantling of cement concrete (un-reinforced) kerb stone and the like of any description of and in any position not otherwise specially provided for complete all as specified and directed.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and over 15mm thick screed bed in CM 1:6 complete all as specified& directed by Engr-in-Charge.

M&L Glazed ceramic coloured tiles in vertical surface 300x200X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified& directed by Engr-in-Charge.

M&L Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified & directed by Engr-in-Charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) of any thickness complete all as specified and directed.

M&L for false ceiling made out of E-board classic of size 595 x 595 x 4 mm thick, (as approved by GE) fixed with existing frame work fixing the board to frame complete all as per manufacurers instructions all as directed and specified.

Dismantling of false ceiling grid any type including cover fillets complete all as specified and directed.

M&L for GI frame consisting of main Tee of size 38.50 x 24.00 mm and cross Tee of size 28.50 x 24.00 mm thick made out of PGI sheet 0.30 mm thick doubled at web and single at flange, flange covered with powder coated sheet 0.25 mm thick and angle 24.00 x 24.00 x0.4 mm thick powder coated suspended with GI wire 3 mm dia and up to 2 Mtrs long complete including plugging fixing of angle to brick walls with steel rawl plugs @ 450 mm c/c complete all as specified and as directed by Engineer-in-Charge. Note : ceiling board measured and paid separately in respective items

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings.

M&L Pre- painted galvatume aluminum zinc coating GI based Semi-corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engr-in-Charge.

Demolition Mud in roofs, any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed by Engr-in-Charge.

M&L for providing cement concrete in type B0 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to (consolidated thickness 65mm or less) as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified& directed by Engr-in-Charge.

M&L screed laid 15mm thick in CM 1:4 as in roof over green concrete surface finished even and smooth using Lequid WPC complete all as specified. Note :-Lequid WPC will be measured and paid seperately)

Supply only integral liquid water proofing compound (ISI marked).

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L rendering 10mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in CM 1:4 on stone wall surfaces or other than fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound ( water proof compound paid seperatly) all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L for preparation of new plastered surfaces of walls and applying one coats of Oil bound distemper over a coat of 1mm thick wall care putty of approved tint complete all as specified & directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified.

Material and labour for preparation of newly plastered surface of walls & applying two coats of external emulision paint in camouflange pattern over a coat of primer complete all as specified.

Material and labour for preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified.

Providing and applying existing plaster/Old surfaces of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed

M & L for complete removal of existing treatment on walls/ceilings and preparation of surfaces of walls/ceilings and applying two coats of OBD ( oil bound distemper) over a coat 1mm thick parris putty complete all as specified and directed by Engr-in -Charge.

S&F powder coated stainless steel drapery rod of 25 mm inner dia (in lengths as directed) of approved colour with & including decorative bowel at both ends and pair of powder coated mild steel brackets fixed at both ends with PVC rawl plug & steel screws on walls/beam, including PVC curtain rings of matching colour @ 10cm C/C all as specified & as directed.

Taking down chowkhats (without taking off shutters from the frames) chowkatts n exc 1.5 sqm each complete all as specified & directed by Engr-in-Charge.

Taking down chowkatts (without taking off shutters from the frames) chowkatts exc 1.5 sq. m but n exc 4 sq m each complete all as specified & directed by Engr-in-Charge.

Taking down shutter of any decription exc.1Sqm and n.Exc 2 Sqm complete all as specified & directed by Engr-in-Charge.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

M&L Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified& directed by Engr-in-Charge.

S&F stainless steel hinges 100mm long medium weight, complete all as specified & directed by Engr-in-Charge.

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed by Engr-in-Charge.

S&F 150mm Aluminium handles, cast type, anodised complete all as specified & directed by Engr-in-Charge.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge Note : Glazing/penelling measured and paid saperately in respective items.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed. Note : Glazing/penelling measured and paid saperately in respective items.

Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m ,powder coated of any colour as approved (Thickness or powder coating not less than 50 micron)including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified Note : Glazing/penelling measured and paid saperately in respective items.

S&F anodized aluminium grill with power coating (minimum thickness 50 micron) of approved pattern and fixed to the existing window/ventilator frame with CP brass/stainless steel scrwed @ 200mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete as per requirement & directed by Engr-in-Charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for Slinding shutters of doors, windows & ventilators including providing and fixing hinges/ pivots/rollers and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge Note : Glazing/penelling measured and paid saperately in respective items.

S&F 4.8mm thick Sheet glass, ordinary quality and glazing with rubber bedding in square n exc 0.5 sq.m in each pane complete all as specified & directed by Engr-in-Charge.

S&F 5mm thick frosted glass with rubber bedding in square n exc 0.5 sq.m in each pane complete all as specified & directed by Engr-in-Charge.

S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining/Aluminium partion/aluminium door/window, Insulated PVC/Aluminium Wall Lining, and Solid PVC/Aluminium Partitions and fixing at site complete all as specified & directed by Engr-in-Charge.

S&F for 18/19mm thick High Density High Moisture Resistant board (HDHMR) Prelaminated both sides as in Controller's Desk ,palmed boxes,showcase,shutters of Cup Boards etc including 6mm designing teak wood beading on edges complete all as specified and as directed by Engr-in-Charge.

S&F 75mm extruded brass handles, fabricated type polished complete all as specified & directed by Engr-in-Charge.

S & F Width of flaps (when open) 30mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified & directed by Engr-in-Charge.

S&F FAST DM01SS Stainless Steel Furniture Door Catcher Magnet Size No. 2 for for Wadrobe, Cupboard and Almirah Door. (SS MAT) with Mounting Screw complete all as specified

S&F DOOR SEAL BOTTOM, DOOR AIR GAP RUBBER SHIELD (Best Quality) Anti Rust , Brown/white/balck colour, Black Rubber Complete all as specified

S&F of venation blinds( super quality) to window/ventilator complete all as specified and directed by Engr-in-Charge

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engr-in-Charge

Dismantling timber scantlings 40 sq. cm and over in section, in any position

M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240 Complete all as specified

M&L painting to new or previously untreated steel surfaces of any description over 10cm in width or girth with two coats of synthetic enamel paint over a coat of zinc chromic primer including preparation of surfaces complete all as specified

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified

Taking up or down 15mm steel tubing and connections, complete all as specified& directed by Engr-in-Charge.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed by Engr-in-Charge.

Taking up or down 20mm steel tubing and connections, complete all as specified & directed by Engr-in-Charge.

S&F 20mm GI tubing Medium grade fix to wall/floor complete all as specified & directed by Engr-in-Charge.

Taking up or down any size steel tubing and connections, including cleaning for re fixing and Refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and directed by Engr-in-Charge

M&L for brick/stone work cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Dismantling taking down water tanks of capacity exc 250ltr but not exc 500ltr and removing from site complete all as specified & directed by Engr-in-Charge.

S&F Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified & directed by Engr-in-Charge.

S&F ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 15 mm dia complete all as specified & directed by Engr-in-Charge

S&F Sand cast,100 mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,laid in trenches or in floors and complete all as specified & directed by Engr-in-Charge.

S&F Sand cast,100 mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in wall and complete all as specified & directed by Engr-in-Charge.

S&F Sand cast,75 mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors and complete all as specified & directed by Engr-in-Charge.

S&F Sand cast,75 mm dia Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in wall and complete all as specified & directed by Engr-in-Charge.

S&F CI Bends 100 mm dia (any radius),diminishing pieces or tapers (larger bore measured) complete all as specified & directed by Engr-in-Charge.

S&F CI Bends 75 mm dia (any radius),diminishing pieces or tapers (larger bore measured) complete all as specified & directed by Engr-in-Charge.

S&F 100mm Cast iron floor trap, with grating doom including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & directed by Engr-in-Charge.

S&F 75mm Cast iron floor trap, with grating doom including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & directed by Engr-in-Charge.

S&F 100mm dia Cast iron cowls complete all as specified & directed by Engr-in-Charge.

S&F 75mm dia Cast iron cowls complete all as specified & directed by Engr-in-Charge.

S&F 100mm dia pipe Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified & directed by Engr-in-Charge.

S&F 75mm dia pipe Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified & directed by Engr-in-Charge.

S&F for 150mm x150mm Salt-glazed stoneware gully traps, square or round mouthed, type 'P' including dismsntling old trap complete all as specified & directed by Engr-in-Charge.

S&F fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed omplete all as specified & directed by Engr-in-Charge.

S&F angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified & directed by Engr-in-Charge.

S&F vitreous china wash down water closet pan (Padestal pattern), white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging devicecomplete all as specified & directed by Engr-in-Charge.

S&F PVC valveless, syphonic action type, flushing cistern of 10 ltrs capacity low level, white, with intel, ball valve, float and handle including brackets complete all as specified & directed by Engr-in-Charge.

S&F brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified & directed by Engr-in-Charge.

S&F PVC connection of 15mm bore with 2 Nos. PTMT nuts, 60cm long fixed with one end to pillar tap & the other end to stop cock or iron pipe all as directed by Engineer-in-charge.

S&F Pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified & directed by Engr-in-Charge.

S&F for 32mm dia Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified & directed by Engr-in-Charge.

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges fixed to wall complete all as specified and directed.

S&F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified& directed

S&F Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified & directed by Engr-in-Charge.

M&L for formwork to soffits of suspended slabs such as wash hand basin ,roof slabs, floor slabs, landings and similar work, not exc 200mm thick (horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 , using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for mild steel TMT bars 10mm dia & over cut to length bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and bending with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F vitreous china wash basin white of size 550x400mm (ISI marked) flat back or angle back type excluding taps, waste chain & plug but incuding cast iron brackets and cutting for and pinning in ends of brackets or erecting stand complete fixed in repairs all as specified and directed.

S&F white vitreous china oval shaped wash hand basin of size 55cm X 40cm and including CP waste coupling complete all as directed by the Engr-in-charge.

S&F Urinal half stall flat back of size 580mm x 380mm x 350mm and including waste fitting with CP bottle trap, flushing cistern for urinal shall be vitrous china automatic high level and at minimum of height of 125cm from top of urinal pan and cistern shall be on valve less simphon principle and capacity exc 5ltr and over flow pipe shall be 20mm dia GI pipe medium grade all necessary fittings complete all as specified and directed by Engr-in-Charge.

S&F 32mm dia waste fitting (waste coupling) brass chromium plated for glazed ware sink, basin etc with long screwed shanks and fly nuts flange complete for the following sizes all as directed by Engr-in-charge

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor Overall length of cover plate 140mm complete all as specified & directed by Engr-in-Charge.

S&F in repair for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, fixed in repairs, with & including replacement of floor tiles if any broken during repair work and making good disturbed surfaces matching to the existing surfaces complete all as directed

M & L for concealed point wiring complete with PVC insulated and unsheathed FRLS cable of 1.5 sqmm (nominal area) with multi stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit ISI marked medium grade not less than 20 mm dia, with MS stove enamelled sunken boxes (normal and modular type as required) including earth dolly with plastic laminated sheet top cover (cover plate with frame in case of modular) of approved make and colour including 1.5 sqmm multi stranded FRLS copper conductor cable of green colour as continuous earth wire with lugs and accesseries and making good disturbed surfaces of walls/floor etc complete all as specified and directed for the followings :- One light / fan point controlled by one way switch

All as per above item No-116 here in before One 5 Amp socket outlet on independent board complete all as specified & directed by Engr-in-Charge.

All as per above item No-116 here in before One 5 Amp socket outlet on same board complete all as specified & directed by Engr-in-Charge.

All as per above item No-116 here in before but using 2.5 sqmm single core multi stranded copper conductor PVC insulated and unsheathed, FRLS cable for 15 Amp socket outlet on independent board including 2.5 sqmm multi stranded copper conductor cable of green colour as continuous earth wire with lugs etc as required complete all as specified and as directed.

S&F switch piano type 5 amp one way ISI Marked complete all as specified and directed by Engineer-in-Charge.

S&F switch piano type15 Amps one way ISI Marked complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F socket outlet 2-in-1, 6 pin 5 amp and 15 amps all as specified and directed.

S&F electronic fan regulator Step type complete all as specified and directed.

S&F of ceiling rose surface bakelite 63 x50mm three terminals complete all as specified and as directed.

S & F sub main wiring with PVC insulated, FRLS unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 4.0 sqmm (Nominal area) drawn in and including concealed PVC conduit of suitable size as directed with and including one run of 4.0 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed. Note: (i) Two runs of 4.0 sqmm cable and one run of 4.0 sqmm cable of earth continuity conductor and conduit shall be a unit length.

S & F sub main wiring with PVC insulated, FRLS, unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 6.0 sqmm (Nominal area) drawn in and including concealed PVC conduit of suitable size as directed with and including one run of 6.0 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed. Note: (i) Two runs of 6.0 sqmm cable and one run of 6.0 sqmm cable of earth continuity conductor and conduit shall be a unit length.

S & F sub main wiring with PVC insulated, FRLS, unsheathed two single core cable 1100 volts grade with stranded copper conductor of size 10.0 sqmm (Nominal area) drawn in and including concealed PVC conduit of suitable size as directed with and including one run of 10.0 sqmm multi stranded copper conductor single core PVC insulated, unsheathed cable of green colour as continuous earth wire including lugs etc connected and tested complete all as specified and as directed. Note: (i) Two runs of 10.0 sqmm cable and one run of 10.0 sqmm cable of earth continuity conductor and conduit shall be a unit length.

S & F Regid non-metallic PVC conduit 25 mm (external dia) ISI marked (on surface) incl of all accessories and all fittings such as Tees bends, elbows, reducers, bell mouth, tube ends and fixing accossories such as couplers lock nuts, saddles, pipe hook etc complete all as specified and as directed.

S&F sheet metal enclosure double door concealed suitable for SPN distribution boards when MCB to be used having 200 Amp rated bus bar 12 ways 240 V including fixing in new location with connection of circuit and submain as per site requirement complete all as specified and as directed . Note- (a) MCBs are to be measured and paid seperately. (b)Make of MCBs and DB should be same.(c) Extra circuit length where DBs are to be shifted from existing location to new location shall deemed to be included in the quoted rate.

S&F sheet metal enclosure double door concealed suitable for SPN distribution boards when MCB to be used having 200 Amp rated bus bar 8 ways 240 V including fixing in new location with connection of circuit and submain as per site requirement complete all as specified and as directed . Note- (a) MCBs are to be measured and paid seperately. (b)Make of MCBs and DB should be same.(c) Extra circuit length where DBs are to be shifted from existing location to new location shall deemed to be included in the quoted rate.

S&F sheet metal enclosure double door concealed suitable for SPN distribution boards when MCB to be used having 200 Amp rated bus bar 4 ways 240 V including fixing in new location with connection of circuit and submain as per site requirement complete all as specified and as directed . Note- (a) MCBs are to be measured and paid seperately. (b)Make of MCBs and DB should be same.(c) Extra circuit length where DBs are to be shifted from existing location to new location shall deemed to be included in the quoted rate.

S&F single pole and neutral enclosure with 2 pin and metal earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed.

S&F of Double door three phase prewired distribution board 4 way loadline VTPN when MCCB to be used as incomer and made out of CRCA sheets 1.6 mm thick, phosphatised powder coated with Bus Bar 200 Amps, 415 V, Earth Stud, Din Rail, Polymide terminal blocks for incoming and outgoing circuits, inbuilt loose wire box ,ground terminal blocks ,duly prewired with thimbled flame retardant copper conductors and poly layer for protection complete all as specified and directed (Note:-(a) MCCB and MCBs are to be measured and paid for seperately. (b) Make of MCBs/MCCBs and DB should be same.

S&F MCB SP 5 to 40 Amps, 240 volts curve 'B',breaking capacity 10KA, all as specified and as directed.

S&F MCB SPN 16 to 40 Amps, 240 volts, curve 'B', breaking capacity 10 KA, all as specified and as directed.

S&F MCB SPN 50 to 63 Amps, 240 volts, curve 'B', breaking capacity 10 KA, all as specified and as directed.

S&F MCCB , 125 Amps, 4Pole with adjustable thermal setting and rupturing capacity 16 kA complete all as specified and directed.

Supply and fixing Earthing to DBs /street light pole with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to main earth lead 4.0 sqmm galvanised iron wire by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead shall be protected by GI pipe 15 mm dia medium grade and connected to distribution board including excavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion complete all as specified and as directed.

M & L for Earth continuity conductor or main earthing lead of 4.0 Sqmm galvanized iron wire, buried in ground or fixed to wall in and including 15 mm bore GI pipe medium grade for protection of earth wire complete all as specified and directed. Note :- for item No. 160 and 161 cost of making good of disturbed surface /area to match with existing surface is deemed to be inclued in the quoted rate

S&F enviroment friendly,ultra modern,energy saving surface mounted decorative 10 Watt LED bulkhead fitting with pressure die cast aluminium housing ,high efficient LEDs with opal diffuser and IP65 protectio, lumen efficacy 85 lm/watt with colour temerature 6500K, THD≤ 20 CRI>80,2.5 kV surge protection all as specified and directed.

S&F enviroment friendly indoor decorative 20 Watt LED polycarbonate Batten with opal diffuser , operating voltage range 140v to 270 V, Driver efficiency 88%, lumen efficiency =100 lm/watt , THD≤ 20 CRI>80 , colour temperature 6500 K, inbuilt surge protection = 2.5 Kv, isolation=3.75, and with zero mercury content including all accessaries all as specified and directed.

S & F enviroment friendly recess/pendent mounting 36 watt LED flat panel 2'x2' fabricated CRCA sheet steel duly powder coated housing cool white with high efficient LEDs & glare free opal diffuser PF>0.95 , lumen efficacy>100 lm/W, THD<10% operating range 220v to 240V,CRI>80 including connection with existing wire and all accessaries all as specified and directed

M&L for flame proof wiring with single core PVC insulated and unsheathed 1100 volt grade FRLS electric cable with size 2.5 Sqmm phase and neutral drawn in and including ERW rigid steel stove enameled black conduit heavy duty ISI marked of size 20mm dia on surface/wall/ceiling including all flame proof conduct fittings and accessories such as tees junction boxes, bends duly tested by CMRI Dhanbad suitable for one light /fan point controlled by one flame proof rotary switch SP one way and including drawing continuous earth wire FRLS PVC insulated unsheathed 1100v grade cable with stranded copper conductor of size 2.5 Sqmm and connected to earth dolly complete all as specified and directed by Engrs-in-Charge.

Supply and fixing flame proof/weather proof direct entry type rotary switch single pole on & OFF rotary motion switch in cast aluminum alloy LM-6 enclosure epoxy powder coated single pole 230Volts 10 Amps, AC ON/OFF switch operated externally by Knob having 02 Nos of M-20 cable entries, earthing terminals suitable for mounting on Wall/Steel structure etc all as specified and directed.

Supply and fixing LED light fitting 1x16/20 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver,holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed Note :- (a) All fittings shall be ISI marked and shall have approval of CMRI Dhanbad .(b) Original Test certificate of Manufacturer shall be produced by Contractor

Supply and fixing of PVC round shape junction box cover of suitable size including fcomplete all as specified and as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, 1400 RPM, blades, and frame and louver complete with making arrangement for fixing of exhaust fan on steel/Aluminium frame window/ making opening in brick wall as per site requirement and also making good to disturbed surfaces as per matching to existing complete all as specified and as directed by Engr-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed by Engr-in-Charge.

Supply & fix wall mounting fans 230 volts single phase oscillating 400 mm sweep suitable for wall mounting complete all as specified and as directed by Engr-in-Charge.

S&F wall mounted Air circulator 750 mm sweep including copper wound motor ,metallic body , 50 Hz , 240 volt 1440 RPM including all fixing accessories complete all as specified and directed.

Taking down light fittings of any type any size any location complete all as specifed and directed.

Taking down DB including old U/s MCB/MCCB of any size any type from any location complete all as specifed and directed.

Taking down carefully copper / aluminium point wiring light / fan, socket or power point complete including fittings such as switches, sockets, ceiling rose, bell push bell buzzer lamp holder bracket etc. removing from site and making good disturbed surface of wall, floor etc complete all as specified and as directed.

Taking down carefully copper / aluminium Sub main wiring removing from site and making good disturbed surface of wall, etc complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide & not exc 1.5 mtr deep and getting out for taking out/laying cable, poles & stay etc complete all as specified and directed by engr-in-charge.

Returning, filling in including spresding leveling watering and well ramming in layers not exceeding 25cm thick after the cable have been laid and tested complete all as specified and directed by Engr-in-Charge..

Removal of excavated surplus soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engr-in-Charge.

M & L for dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying ( total 23 cm ) and compaction till 18 cm thick for measurement purpose complete all as specified and directed .

Material labour for common burnt clay bricks, sub class 'B' grade laid in trenches for protection of UG cables perpendicular to the direction of the cables complete all as specified and as directed by Engr-in-Charge

M & L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation of pole or similar works complete all as specified and directed.

M & L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete for fixing of pole complete all as specified and directed.

M & L for cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for copings of poles/stay/panels complete all as specified and directed.

Supply and erect true vertical steel tubular swaged pole confirming to IS-2713 part-II 410 SP-31 ,9.0 meter long complete with MS base plate of 6 mm thick of size 300x300 mm , finial taper plug, cap , bolt, nuts, eashers including painting externally with two coats of aluminium paint over a coat of red oxide primer for exposed portion and two coats of black bituminious paint for embeded portion in concrete as well as throughout internally including povision of white and blue colour strips with fluorescent paint upto 1.5 mtr height and numbering of pole complete all as specified and directes by engr-in-charge.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 protection with 4KV driver builtin sugre protection & additional 10KV surge protection device, system lumens 3500 lm, THD≤10%, efficacy not less than 100 lm/watt, Colour temp 5700 K , CRI ≥ 70, Prower Factor ≥0.95 complete and impact resistance IK07 f complete all as specified and directed by engr-in-charge.

M&L street light bracket made out from GI Pipe 32 mm bore, light grade, 1.2 m long bent to shape including fixing 02 set of clamp made out from MS Flats of size 25x5 mm complete with nuts and bolts and washers of suitable size duly painted with two coats of aluminium paint over a coat of red oxide primer all as specified and directed .

S&F non metallic junction box made out of thermoplastic of size 250x250x160 mm for street light poles with connector for connection incoming and outgoing cables including provn of 01 No MCB SP 2 Amp to control the pole light circuit including 4 nos aluminium bus bars mounting on the insulator and fixing clamp made of FI 25x3 mm with back strip with suitable nut, bolts and washers including suitable size of double compression cable glands for incoming and outgoing cables complete all as specified and directed.

S & F PVC insulated copper wire 2.5 sqmm 3 core for street light fitting from juction box to fitting comple along with suitable clamps all as specified and directed.

M&L for GI pipes 40 mm dia light grade for cable protection in trenches / poles complete all as specified and as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core all as specified and directed.

Boring of holes under road, pavement, hard standing by trenchless technology including HDPE pipe of 25 mm dia suitable for 0.4 mpa working pressure complete all as specified and directed.

Supply ,install testing and commissioning of energy efficient hi wall split Type Airconditioner with indoor & outdoor unit complete with Inverter Technology, 3D Airflow, power chill operation,cordless remote control unit and with in built air ioniser, PM 2.5 Filter for better indoor air quality with 5 star rating and EER 3.2 of capacity 1.5 TR with precharged CFC free refrigerant including cutting the holes and making good the disturbed surface with existing colour all as specified and directed by Engr-in-Charge. Note-cost of Outdoor unit stand shall be included in quoted rate.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 120 V to 280 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 5 KVA complete all as specified and directed.

S&F in replacement switch piano type 5 amp one way ISI Marked complete all as specified and directed by Engineer-in-Charge.

S&F in replacement switch piano type15 Amps one way ISI Marked complete all as specified and directed by Engineer-in-Charge.

S&F in replacement socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer-in-Charge.

S&F in replacement socket outlet 2-in-1, 6 pin 5 amp and 15 amps all as specified and directed.

S&F in replacement electronic fan regulator Step type complete all as specified and directed.

S&F in replacement of ceiling rose surface bakelite 63 x50mm three terminals complete all as specified and as directed.

S&F in replacement MCB SP 5 to 40 Amps, 240 volts curve 'B',breaking capacity 10KA, all as specified and as directed.

S&F in replacement MCB SPN 16 to 40 Amps, 240 volts, curve 'B', breaking capacity 10 KA, all as specified and as directed.

S&F in replacement MCB SPN 50 to 63 Amps, 240 volts, curve 'B', breaking capacity 10 KA, all as specified and as directed.

S&F in replacement single pole and neutral enclosure with 2 pin and metal earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed.

S&F in replacement MCB TPN 63 Amps, 415 volts, curve 'B', breaking capacity 10 KA, all as specified and as directed.