COMPREHENSIVE MAINT AND MISC REPAIRS AT SPORTS COMPLEX ENGR REGT MES COMPLEX AND STN HQ UNDER AGE BR II OF GE SUKNA

Amount

M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) in top of chajja , roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and as directed.

M&L PCC 1:2:4 type C-1 (using 12.50 mm graded crushed stone aggregate) as in bed plates, filling in pressed steel door frames, hold fast blocks etc, complete all as specified and directed.

M&L for Reinforced Cement Concrete Type B-1 1:2:4 Nominal mix (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M&L PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in gap between roof sheets and brick wall, thickness of concrete bed exc. 5 cm and not exc.10 cm thick & width not exc. width of one brick thick wall including necessary scaffolding and formwork ht up to 7m complete all as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:6 complete all as specified and directed.

M & L for applying evenly a coat of blown type bitumen @ 1.50 Kg per Sqm including cleaning of surface and binding with clean dry sand @ 0.05 cum per Sqm including 150 micron Polythene film thick laid on a coat of bitumen primer, @0.30 to @ 0.50 kg per Sqm complete all as specified & directed.

M& L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting n.exc. 10 cm in girth complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side with liping/frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down and refixing in the same opening shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed. (Note-Renewal of builder's hard?ware articles, if specially ordered, shall be paid seperately for at 'supplied only' rates)

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 10 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling of grid size 605 x 605 mm including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all as specified and directed.

S & F in repair MS Helical door spring 150 mm size including roller and roller plate fixed to wooden or steel frames with welding etc complete all as specified and directed.

S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Hasp and staple 100 mm safety type brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and as directed.

S&F in repairs curtain harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. with two Nos of socket ,end caps and brakets (decorative type) complete for doors/window opening complete all as specified and directed.

S & F in repairs Stainless Steel Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

Supply & Fix floor door stopper of brass body and tongues with hard drawn steel spring, overall length cover plate 150 mm complete all as specified and directed

S & F Ball catches with 8 mm dia., steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repair Stainless steel kitchen rack made out of stainless steel sheet 1mm thick with approx size 900mmx900mmx250mm best quality complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S & F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Structural steel work of angle, channel etc., confirming to Fe 410 -W (Gde- E- 250) complete all as specified and directed.

S&F Roof truss (framed) trussed, purlins,crane gantires of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1998 grade St-240 including one shop coat of zink chromate primer paint including preparation of surface including dismantling complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S & F Steel ventilator with centre hung shutters including two pairs of brass cup pivots, catch spring and pulley wheel complete all as specified and directed.

S&F Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F pre-painted 4 mm thick E-board designer/ decorative ceiling of size 600x600mm fixed or laid / inserted to aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including anodised aluminium snap grid frame work for false ceiling hanging from structural steel / scantling with 6 mm GI wire (upo 1200mm length)adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size 600 mm long and expansion hold fastners 12.50 mm dia 40 mm long with and including building board complete all as specified and directed.

M&L for in repairs 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M&L in repairs 12 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & oter side balancing white lamination, fixed with screws to timber frame work as in selves complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm (minimum) thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing including cutting two groove line and laid over 25 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L machine cut kota stone 20-25 mm (minimum) thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 20 mm thick screed bed in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the stone and including rubbing / grinding and polishing complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 20 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc and laid fair in alternate bays and in including filler joints with sealing compound grade 'A' if required finished even and smooth without using extra cement complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor, etc complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in sunken portion complete all as specified and directed.

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n.exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 finish even and rough complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 cm thick backing with cm 1:3 complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm laid on floor surface jointed and pointed with coloured cement over and including 15 mm thick screed bed in cement mortar 1:6 with bedding complete all as specified and as directed by Engineer-in-Charge.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 10 mm thick in CM 1:3 complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for rendering 10 mm thick on brick or concrete surfaces etc in cement mortar 1:4 using WPC @ 2% by wt of cement at all around and base of sunken floor with proper slope complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for preparing old surfaces of walls (old decorated plastered or unplastered) and applying one coat of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L complete removal of existing treatment of old plastered ceilings surfaces and applying three coats of white wash complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L preparing of old plastered or un plastered surface of walls and applying one coats of oil bound distemper complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L preparation of old plastered wall surfaces and including applying one coat of cement base paint complete all as specified and directed.

M&L complete removal of existing treatment and preparation of old plastered wall surfaces and including applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L preperation of old decorated wall surfaces and including applying one coat of exterior weather coat paint complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S&F 4 mm thick tinted glass of any size with aluminium bedding and complete all as specified and directed.

S&F 4 mm thick frosted / pin headed glass in ventilator shutters complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

M&L for preparation of new painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of Synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors including taking up or down complete all as specified and directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors including taking up or down complete all as specified and directed.

M&L in repairs High dencity polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to wall,ceiling or floors etc.40 mm bore pipe complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), including 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank including dismantling of old tank complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 500 ltr to 1000 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

S & F in repair 15 mm bore bib tap chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs pillar tap 15 mm bore, fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repairs 15 mm bore stop cock fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S & F Fancy type chromium plated with long shank and cup (Concealed type) 15 mm bore Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repirs towel ring of PTMT fixed with and including Chromium plated brass screws and wooden / plastic cleats (minimum weight 90 gms) complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 600 mm & suitable for cold/hot water supply complete all as specified and directed.

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 75 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) branch piece single, (single Y) equal or unequal, complete all as specified and directed.

S & F 75 mm bore PVC (SWR) junction single, (single T) equal or unequal, complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single, (single T) equal or unequal, complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repairs vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S & F in repairs Vitreous China Squatting pan of Orissa pattern, size 580x440 mm size white with integral foot rest with Cast Iron `P' or `S' trap, front or back inlet and including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete bedding complete including making good to floor (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15 mm dia steel pipe complete all as specified and directed.

S&F in repairs Soap dish, Chromium plated approximate size 160x160x90mm white or SS fixed to wall with plugs with chromium plated screws and wooden/plastic cleats complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs Toilet paper holder brass chromium plated or stainless steel with flat recessed type complete all as specified and directed.

S&F in repairs health faucet 12 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook and connection with angular stop cock complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided including padding concrete on roof all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismentling boarding of any description, fixed in any position with nails as in cub board Self and partition ceiling complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surfaceduly miximg WPC. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (Contd...)

(iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (v) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction. (d) APP based polymeric membrane shall be manufactured by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (e) Water proofing paint shall be by M/s STP Ltd or Berger Paints or M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited

R N De (BID ID -3107403)

ASHISH ROY (BID ID -3105039)

DAS AND GHOSH CONSTRUCTION (BID ID -3103622)

M/S ASHRAFI CONSTRUCTION (BID ID -3108082)

SHIVALAYA ENTERPRISES (BID ID -3104095)

VICKY ENTERPRISES (BID ID -3103305)

M/s Ranjit Kumar Saha (BID ID -3103783)

R K UDYOG (BID ID -3106495)

M/S EASTERN ENGINEERING (BID ID -3104859)