(1) Replacing of damaged Cable 33 KV Line SIKANDARPUR Muzaffarnagar (2) Strengthening works 33 KV Line ANTHWADA (3) Work of 33 KV line PANNAWALI

1. Supply of following material G.I Angle (65×65×6)mm

G.I Channel (125×65)mm

Stay Sets (20x1800) mm

Stay wire G.I 7/8 SWG

G.I Wire No. 6 SWG

M.S. Earthing Rod

V Type Cross Arm 33 KV

Cross Arm Holding clamp for PCC Pole 9 M + S.T. Pole 11 M long & 13M long

Top Channel Holding Clamp for PCC Pole 9 M + S.T. Pole 11 M long & 13M long

Stay Clamp for PCC Pole 9 M + S.T. Pole 11 M long & 13M long

F Bracket for 33 KV

E Bracket for 33 KV

Danger Board with clamp for PCC Pole 9 M + S.T. Pole 11 M long & 13M long

Braccing clamps clamp for PCC Pole 9 M + S.T. Pole 11 M long & 13M long (Upper & Lower)

Aluminum Binding wire

Barbed wire

Grouting of Stay

Red Oxide Paint

Aluminium paint

M.S. Bolts Nuts & Washers

Earth wire clamp with Nut & Bolts

Concreting of support

Stone pad (300×300×75)mm

P.G. clamp for Dog to Dog conductor

Outdoor type cable jointing kit for 33 kv XLPE cable

HDPE, 80PN, 150 mm dia Pipe

G.I pipe 150mm dia 3 mtr long .

2. Safe carriage of with loading & unloading at both ends respectively. (under jurisdiction of PVVNL) a) ACSR Dog Conductor

b) 33 KV Pin Isulators (Polymer)

c) Disc Insulators B&S 7000 Kg. (Polymer)

d) Disc Fittings B&S for Dog 70 KN (Polymer)

e) Steel Tublar Pole SP-55 11M (Bottom Portion Galvanized)

f) 33 KV, 3×300mm² XLPE Cable

A- Erection of support after excavation of foundation pit in mix soil/normal soil/soft & hard rock and its back filling and leveling etc. The size of the pit will be (900×600)mm and having depth of 1/6th of the full length of the support & Erection of support. The work includes carriage and handling of supports from site store to pit site. (i) 11 M Long STP, SP-55 Round Pole

B- Fixing of all clamps, Cross Bracing Sets 3.5 Mtr. from M.S. Angle 65×65×6mm/50×50×6mm & other accessories on the supports as per drawing. Work includes cutting of holes and providing M.S. Bolts of 16×40mm size in the middle of cross bracing with 1 no. spring washer. The work also includes carriage & handling of accessories from sectional store to pit site as well as any fabrication work if required. (i) Single Pole (a) 11 M Long STP, SP-55 Round Pole

(ii) Double Pole Structures (a) 11 M Long STP, SP-55 Round Pole

Grouting of supports in CC 1:4:8 (Cement, sand & 40 mm brick ballast) Grouting will be done in the block of size (450×450)mm ×1/6th of full length of the support, up to ground level, 300 mm plinth above the ground level with C.C. 1:3:6 (Cement, Course sand and Stone grit) with muffing as per drawing, work includes back filling and proper ramming. (i) 11 M Long STP, SP-55 Round Pole

Grouting of stay rods (20×1800)mm including all work of excavation, cement concrete in size (0.60 × 0.60 × 0.30)m in ratio 1:4:8 cement, sand, 40mm brick ballast) as per drg. including back filling, proper ramming etc and fixing tightening & nozzling of stay wire with stay rod with the poles of required tension as per drawing.

Earthing of supports with MS earth Rod of (20×2500)mm long including excavation of pit and driving M.S. Rod 3.0 M apart from support and 0.5m below the ground level and connecting below the earth electrodes with the help of G.I. wire no. 8 SWG and earthing lugs.

Laying, spreading, lifting and final sagging of 3 phases of ACSR Dog conductor in accordance with profile and sag chart including binding, Jumpering and fixing of P.G. Clamp as per requirement in 03 Nos. conductor in parallel.

Providing & fixing of danger board at each location as per specification of the drawing with clamps etc.

Painting of following supports/structures with 2 coats of synthetic enamel paint after one coat of ready mix primer including cost of all material, as well as rubbing/cleaning of surface as required for proper completion of work. Painting will be done by post office red paint from top to cross arm and remaining by Aluminium paint. (a) All channels, X-Arms and Clamps of 11 Mtr, SP-55 Poles including all channels/X-Arms/Clamps etc (i) Single supports

(ii) Double supports

Wrapping of barbed wire on 33 KV PCC Poles/SP-55 ST & SP-72 ST Poles as anti-climbing device for a length of 0.9 Mtr., wire pitch/gap 13mm and fixing upper and lower end keeping lower end at a height of 2.75 Mtr. from the ground complete with supply and fixing of lower end & upper end clamps made of M.S. Flat 40×5mm complete with nuts & bolts & all other required material.

12. H.T. Power Cable Laying : i) Digging of trench of size 900x1050 mm for laying of 33KV cable including loops.

ii) Safely laying of 33KV 3x300mmsq XLPE cable in cable trench by laying 2 No. Cables in each trench. (single circuit laying)

iii) Safe laying of 33KV XLPE cable in Air on D/P / F/P.

iv) Laying of Ist class bricks along the length on both sides and stone slab 650x450x40 as a top cover over the XLPE cable in trench. (Single circuit laying) (as per RESPO Norms)

v) Filling river sand in side beneath & around cable in the trench.

v) Back filling of excavated earth in the cable trench up to the ground level and remming properly.

Cable Laying in HDPE,Pipe

vi) Making of 33KV outdoor type Heat shrink XLPE Cable Box of size 3x300mmsq and crimping of proper size Aluminium lugs. Work includes providing insulating tapes etc.

Dismentling of dmage STP pole , and associated accessories (steel scrap ) and cartage to nearest store

Dismentling of ACSR conductor, (Alluminium Scrap) and cartage to nearest store

Drilling and Laying of HDPE Pipe of 80PN, 150mm dia.

SHASHI ENTERPRISES

M/S PAWAN CONTRACTOR